2004 строки
49 KiB
C
2004 строки
49 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
||
/*
|
||
* Copyright (c) 2009-2013, 2016-2018, The Linux Foundation. All rights reserved.
|
||
* Copyright (c) 2014, Sony Mobile Communications AB.
|
||
*
|
||
*/
|
||
|
||
#include <linux/acpi.h>
|
||
#include <linux/atomic.h>
|
||
#include <linux/clk.h>
|
||
#include <linux/delay.h>
|
||
#include <linux/dmaengine.h>
|
||
#include <linux/dmapool.h>
|
||
#include <linux/dma-mapping.h>
|
||
#include <linux/err.h>
|
||
#include <linux/i2c.h>
|
||
#include <linux/interrupt.h>
|
||
#include <linux/io.h>
|
||
#include <linux/module.h>
|
||
#include <linux/of.h>
|
||
#include <linux/platform_device.h>
|
||
#include <linux/pm_runtime.h>
|
||
#include <linux/scatterlist.h>
|
||
|
||
/* QUP Registers */
|
||
#define QUP_CONFIG 0x000
|
||
#define QUP_STATE 0x004
|
||
#define QUP_IO_MODE 0x008
|
||
#define QUP_SW_RESET 0x00c
|
||
#define QUP_OPERATIONAL 0x018
|
||
#define QUP_ERROR_FLAGS 0x01c
|
||
#define QUP_ERROR_FLAGS_EN 0x020
|
||
#define QUP_OPERATIONAL_MASK 0x028
|
||
#define QUP_HW_VERSION 0x030
|
||
#define QUP_MX_OUTPUT_CNT 0x100
|
||
#define QUP_OUT_FIFO_BASE 0x110
|
||
#define QUP_MX_WRITE_CNT 0x150
|
||
#define QUP_MX_INPUT_CNT 0x200
|
||
#define QUP_MX_READ_CNT 0x208
|
||
#define QUP_IN_FIFO_BASE 0x218
|
||
#define QUP_I2C_CLK_CTL 0x400
|
||
#define QUP_I2C_STATUS 0x404
|
||
#define QUP_I2C_MASTER_GEN 0x408
|
||
|
||
/* QUP States and reset values */
|
||
#define QUP_RESET_STATE 0
|
||
#define QUP_RUN_STATE 1
|
||
#define QUP_PAUSE_STATE 3
|
||
#define QUP_STATE_MASK 3
|
||
|
||
#define QUP_STATE_VALID BIT(2)
|
||
#define QUP_I2C_MAST_GEN BIT(4)
|
||
#define QUP_I2C_FLUSH BIT(6)
|
||
|
||
#define QUP_OPERATIONAL_RESET 0x000ff0
|
||
#define QUP_I2C_STATUS_RESET 0xfffffc
|
||
|
||
/* QUP OPERATIONAL FLAGS */
|
||
#define QUP_I2C_NACK_FLAG BIT(3)
|
||
#define QUP_OUT_NOT_EMPTY BIT(4)
|
||
#define QUP_IN_NOT_EMPTY BIT(5)
|
||
#define QUP_OUT_FULL BIT(6)
|
||
#define QUP_OUT_SVC_FLAG BIT(8)
|
||
#define QUP_IN_SVC_FLAG BIT(9)
|
||
#define QUP_MX_OUTPUT_DONE BIT(10)
|
||
#define QUP_MX_INPUT_DONE BIT(11)
|
||
#define OUT_BLOCK_WRITE_REQ BIT(12)
|
||
#define IN_BLOCK_READ_REQ BIT(13)
|
||
|
||
/* I2C mini core related values */
|
||
#define QUP_NO_INPUT BIT(7)
|
||
#define QUP_CLOCK_AUTO_GATE BIT(13)
|
||
#define I2C_MINI_CORE (2 << 8)
|
||
#define I2C_N_VAL 15
|
||
#define I2C_N_VAL_V2 7
|
||
|
||
/* Most significant word offset in FIFO port */
|
||
#define QUP_MSW_SHIFT (I2C_N_VAL + 1)
|
||
|
||
/* Packing/Unpacking words in FIFOs, and IO modes */
|
||
#define QUP_OUTPUT_BLK_MODE (1 << 10)
|
||
#define QUP_OUTPUT_BAM_MODE (3 << 10)
|
||
#define QUP_INPUT_BLK_MODE (1 << 12)
|
||
#define QUP_INPUT_BAM_MODE (3 << 12)
|
||
#define QUP_BAM_MODE (QUP_OUTPUT_BAM_MODE | QUP_INPUT_BAM_MODE)
|
||
#define QUP_UNPACK_EN BIT(14)
|
||
#define QUP_PACK_EN BIT(15)
|
||
|
||
#define QUP_REPACK_EN (QUP_UNPACK_EN | QUP_PACK_EN)
|
||
#define QUP_V2_TAGS_EN 1
|
||
|
||
#define QUP_OUTPUT_BLOCK_SIZE(x)(((x) >> 0) & 0x03)
|
||
#define QUP_OUTPUT_FIFO_SIZE(x) (((x) >> 2) & 0x07)
|
||
#define QUP_INPUT_BLOCK_SIZE(x) (((x) >> 5) & 0x03)
|
||
#define QUP_INPUT_FIFO_SIZE(x) (((x) >> 7) & 0x07)
|
||
|
||
/* QUP tags */
|
||
#define QUP_TAG_START (1 << 8)
|
||
#define QUP_TAG_DATA (2 << 8)
|
||
#define QUP_TAG_STOP (3 << 8)
|
||
#define QUP_TAG_REC (4 << 8)
|
||
#define QUP_BAM_INPUT_EOT 0x93
|
||
#define QUP_BAM_FLUSH_STOP 0x96
|
||
|
||
/* QUP v2 tags */
|
||
#define QUP_TAG_V2_START 0x81
|
||
#define QUP_TAG_V2_DATAWR 0x82
|
||
#define QUP_TAG_V2_DATAWR_STOP 0x83
|
||
#define QUP_TAG_V2_DATARD 0x85
|
||
#define QUP_TAG_V2_DATARD_NACK 0x86
|
||
#define QUP_TAG_V2_DATARD_STOP 0x87
|
||
|
||
/* Status, Error flags */
|
||
#define I2C_STATUS_WR_BUFFER_FULL BIT(0)
|
||
#define I2C_STATUS_BUS_ACTIVE BIT(8)
|
||
#define I2C_STATUS_ERROR_MASK 0x38000fc
|
||
#define QUP_STATUS_ERROR_FLAGS 0x7c
|
||
|
||
#define QUP_READ_LIMIT 256
|
||
#define SET_BIT 0x1
|
||
#define RESET_BIT 0x0
|
||
#define ONE_BYTE 0x1
|
||
#define QUP_I2C_MX_CONFIG_DURING_RUN BIT(31)
|
||
|
||
/* Maximum transfer length for single DMA descriptor */
|
||
#define MX_TX_RX_LEN SZ_64K
|
||
#define MX_BLOCKS (MX_TX_RX_LEN / QUP_READ_LIMIT)
|
||
/* Maximum transfer length for all DMA descriptors */
|
||
#define MX_DMA_TX_RX_LEN (2 * MX_TX_RX_LEN)
|
||
#define MX_DMA_BLOCKS (MX_DMA_TX_RX_LEN / QUP_READ_LIMIT)
|
||
|
||
/*
|
||
* Minimum transfer timeout for i2c transfers in seconds. It will be added on
|
||
* the top of maximum transfer time calculated from i2c bus speed to compensate
|
||
* the overheads.
|
||
*/
|
||
#define TOUT_MIN 2
|
||
|
||
/* I2C Frequency Modes */
|
||
#define I2C_STANDARD_FREQ 100000
|
||
#define I2C_FAST_MODE_FREQ 400000
|
||
#define I2C_FAST_MODE_PLUS_FREQ 1000000
|
||
|
||
/* Default values. Use these if FW query fails */
|
||
#define DEFAULT_CLK_FREQ I2C_STANDARD_FREQ
|
||
#define DEFAULT_SRC_CLK 20000000
|
||
|
||
/*
|
||
* Max tags length (start, stop and maximum 2 bytes address) for each QUP
|
||
* data transfer
|
||
*/
|
||
#define QUP_MAX_TAGS_LEN 4
|
||
/* Max data length for each DATARD tags */
|
||
#define RECV_MAX_DATA_LEN 254
|
||
/* TAG length for DATA READ in RX FIFO */
|
||
#define READ_RX_TAGS_LEN 2
|
||
|
||
static unsigned int scl_freq;
|
||
module_param_named(scl_freq, scl_freq, uint, 0444);
|
||
MODULE_PARM_DESC(scl_freq, "SCL frequency override");
|
||
|
||
/*
|
||
* count: no of blocks
|
||
* pos: current block number
|
||
* tx_tag_len: tx tag length for current block
|
||
* rx_tag_len: rx tag length for current block
|
||
* data_len: remaining data length for current message
|
||
* cur_blk_len: data length for current block
|
||
* total_tx_len: total tx length including tag bytes for current QUP transfer
|
||
* total_rx_len: total rx length including tag bytes for current QUP transfer
|
||
* tx_fifo_data_pos: current byte number in TX FIFO word
|
||
* tx_fifo_free: number of free bytes in current QUP block write.
|
||
* rx_fifo_data_pos: current byte number in RX FIFO word
|
||
* fifo_available: number of available bytes in RX FIFO for current
|
||
* QUP block read
|
||
* tx_fifo_data: QUP TX FIFO write works on word basis (4 bytes). New byte write
|
||
* to TX FIFO will be appended in this data and will be written to
|
||
* TX FIFO when all the 4 bytes are available.
|
||
* rx_fifo_data: QUP RX FIFO read works on word basis (4 bytes). This will
|
||
* contains the 4 bytes of RX data.
|
||
* cur_data: pointer to tell cur data position for current message
|
||
* cur_tx_tags: pointer to tell cur position in tags
|
||
* tx_tags_sent: all tx tag bytes have been written in FIFO word
|
||
* send_last_word: for tx FIFO, last word send is pending in current block
|
||
* rx_bytes_read: if all the bytes have been read from rx FIFO.
|
||
* rx_tags_fetched: all the rx tag bytes have been fetched from rx fifo word
|
||
* is_tx_blk_mode: whether tx uses block or FIFO mode in case of non BAM xfer.
|
||
* is_rx_blk_mode: whether rx uses block or FIFO mode in case of non BAM xfer.
|
||
* tags: contains tx tag bytes for current QUP transfer
|
||
*/
|
||
struct qup_i2c_block {
|
||
int count;
|
||
int pos;
|
||
int tx_tag_len;
|
||
int rx_tag_len;
|
||
int data_len;
|
||
int cur_blk_len;
|
||
int total_tx_len;
|
||
int total_rx_len;
|
||
int tx_fifo_data_pos;
|
||
int tx_fifo_free;
|
||
int rx_fifo_data_pos;
|
||
int fifo_available;
|
||
u32 tx_fifo_data;
|
||
u32 rx_fifo_data;
|
||
u8 *cur_data;
|
||
u8 *cur_tx_tags;
|
||
bool tx_tags_sent;
|
||
bool send_last_word;
|
||
bool rx_tags_fetched;
|
||
bool rx_bytes_read;
|
||
bool is_tx_blk_mode;
|
||
bool is_rx_blk_mode;
|
||
u8 tags[6];
|
||
};
|
||
|
||
struct qup_i2c_tag {
|
||
u8 *start;
|
||
dma_addr_t addr;
|
||
};
|
||
|
||
struct qup_i2c_bam {
|
||
struct qup_i2c_tag tag;
|
||
struct dma_chan *dma;
|
||
struct scatterlist *sg;
|
||
unsigned int sg_cnt;
|
||
};
|
||
|
||
struct qup_i2c_dev {
|
||
struct device *dev;
|
||
void __iomem *base;
|
||
int irq;
|
||
struct clk *clk;
|
||
struct clk *pclk;
|
||
struct i2c_adapter adap;
|
||
|
||
int clk_ctl;
|
||
int out_fifo_sz;
|
||
int in_fifo_sz;
|
||
int out_blk_sz;
|
||
int in_blk_sz;
|
||
|
||
int blk_xfer_limit;
|
||
unsigned long one_byte_t;
|
||
unsigned long xfer_timeout;
|
||
struct qup_i2c_block blk;
|
||
|
||
struct i2c_msg *msg;
|
||
/* Current posion in user message buffer */
|
||
int pos;
|
||
/* I2C protocol errors */
|
||
u32 bus_err;
|
||
/* QUP core errors */
|
||
u32 qup_err;
|
||
|
||
/* To check if this is the last msg */
|
||
bool is_last;
|
||
bool is_smbus_read;
|
||
|
||
/* To configure when bus is in run state */
|
||
u32 config_run;
|
||
|
||
/* dma parameters */
|
||
bool is_dma;
|
||
/* To check if the current transfer is using DMA */
|
||
bool use_dma;
|
||
unsigned int max_xfer_sg_len;
|
||
unsigned int tag_buf_pos;
|
||
/* The threshold length above which block mode will be used */
|
||
unsigned int blk_mode_threshold;
|
||
struct dma_pool *dpool;
|
||
struct qup_i2c_tag start_tag;
|
||
struct qup_i2c_bam brx;
|
||
struct qup_i2c_bam btx;
|
||
|
||
struct completion xfer;
|
||
/* function to write data in tx fifo */
|
||
void (*write_tx_fifo)(struct qup_i2c_dev *qup);
|
||
/* function to read data from rx fifo */
|
||
void (*read_rx_fifo)(struct qup_i2c_dev *qup);
|
||
/* function to write tags in tx fifo for i2c read transfer */
|
||
void (*write_rx_tags)(struct qup_i2c_dev *qup);
|
||
};
|
||
|
||
static irqreturn_t qup_i2c_interrupt(int irq, void *dev)
|
||
{
|
||
struct qup_i2c_dev *qup = dev;
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
u32 bus_err;
|
||
u32 qup_err;
|
||
u32 opflags;
|
||
|
||
bus_err = readl(qup->base + QUP_I2C_STATUS);
|
||
qup_err = readl(qup->base + QUP_ERROR_FLAGS);
|
||
opflags = readl(qup->base + QUP_OPERATIONAL);
|
||
|
||
if (!qup->msg) {
|
||
/* Clear Error interrupt */
|
||
writel(QUP_RESET_STATE, qup->base + QUP_STATE);
|
||
return IRQ_HANDLED;
|
||
}
|
||
|
||
bus_err &= I2C_STATUS_ERROR_MASK;
|
||
qup_err &= QUP_STATUS_ERROR_FLAGS;
|
||
|
||
/* Clear the error bits in QUP_ERROR_FLAGS */
|
||
if (qup_err)
|
||
writel(qup_err, qup->base + QUP_ERROR_FLAGS);
|
||
|
||
/* Clear the error bits in QUP_I2C_STATUS */
|
||
if (bus_err)
|
||
writel(bus_err, qup->base + QUP_I2C_STATUS);
|
||
|
||
/*
|
||
* Check for BAM mode and returns if already error has come for current
|
||
* transfer. In Error case, sometimes, QUP generates more than one
|
||
* interrupt.
|
||
*/
|
||
if (qup->use_dma && (qup->qup_err || qup->bus_err))
|
||
return IRQ_HANDLED;
|
||
|
||
/* Reset the QUP State in case of error */
|
||
if (qup_err || bus_err) {
|
||
/*
|
||
* Don’t reset the QUP state in case of BAM mode. The BAM
|
||
* flush operation needs to be scheduled in transfer function
|
||
* which will clear the remaining schedule descriptors in BAM
|
||
* HW FIFO and generates the BAM interrupt.
|
||
*/
|
||
if (!qup->use_dma)
|
||
writel(QUP_RESET_STATE, qup->base + QUP_STATE);
|
||
goto done;
|
||
}
|
||
|
||
if (opflags & QUP_OUT_SVC_FLAG) {
|
||
writel(QUP_OUT_SVC_FLAG, qup->base + QUP_OPERATIONAL);
|
||
|
||
if (opflags & OUT_BLOCK_WRITE_REQ) {
|
||
blk->tx_fifo_free += qup->out_blk_sz;
|
||
if (qup->msg->flags & I2C_M_RD)
|
||
qup->write_rx_tags(qup);
|
||
else
|
||
qup->write_tx_fifo(qup);
|
||
}
|
||
}
|
||
|
||
if (opflags & QUP_IN_SVC_FLAG) {
|
||
writel(QUP_IN_SVC_FLAG, qup->base + QUP_OPERATIONAL);
|
||
|
||
if (!blk->is_rx_blk_mode) {
|
||
blk->fifo_available += qup->in_fifo_sz;
|
||
qup->read_rx_fifo(qup);
|
||
} else if (opflags & IN_BLOCK_READ_REQ) {
|
||
blk->fifo_available += qup->in_blk_sz;
|
||
qup->read_rx_fifo(qup);
|
||
}
|
||
}
|
||
|
||
if (qup->msg->flags & I2C_M_RD) {
|
||
if (!blk->rx_bytes_read)
|
||
return IRQ_HANDLED;
|
||
} else {
|
||
/*
|
||
* Ideally, QUP_MAX_OUTPUT_DONE_FLAG should be checked
|
||
* for FIFO mode also. But, QUP_MAX_OUTPUT_DONE_FLAG lags
|
||
* behind QUP_OUTPUT_SERVICE_FLAG sometimes. The only reason
|
||
* of interrupt for write message in FIFO mode is
|
||
* QUP_MAX_OUTPUT_DONE_FLAG condition.
|
||
*/
|
||
if (blk->is_tx_blk_mode && !(opflags & QUP_MX_OUTPUT_DONE))
|
||
return IRQ_HANDLED;
|
||
}
|
||
|
||
done:
|
||
qup->qup_err = qup_err;
|
||
qup->bus_err = bus_err;
|
||
complete(&qup->xfer);
|
||
return IRQ_HANDLED;
|
||
}
|
||
|
||
static int qup_i2c_poll_state_mask(struct qup_i2c_dev *qup,
|
||
u32 req_state, u32 req_mask)
|
||
{
|
||
int retries = 1;
|
||
u32 state;
|
||
|
||
/*
|
||
* State transition takes 3 AHB clocks cycles + 3 I2C master clock
|
||
* cycles. So retry once after a 1uS delay.
|
||
*/
|
||
do {
|
||
state = readl(qup->base + QUP_STATE);
|
||
|
||
if (state & QUP_STATE_VALID &&
|
||
(state & req_mask) == req_state)
|
||
return 0;
|
||
|
||
udelay(1);
|
||
} while (retries--);
|
||
|
||
return -ETIMEDOUT;
|
||
}
|
||
|
||
static int qup_i2c_poll_state(struct qup_i2c_dev *qup, u32 req_state)
|
||
{
|
||
return qup_i2c_poll_state_mask(qup, req_state, QUP_STATE_MASK);
|
||
}
|
||
|
||
static void qup_i2c_flush(struct qup_i2c_dev *qup)
|
||
{
|
||
u32 val = readl(qup->base + QUP_STATE);
|
||
|
||
val |= QUP_I2C_FLUSH;
|
||
writel(val, qup->base + QUP_STATE);
|
||
}
|
||
|
||
static int qup_i2c_poll_state_valid(struct qup_i2c_dev *qup)
|
||
{
|
||
return qup_i2c_poll_state_mask(qup, 0, 0);
|
||
}
|
||
|
||
static int qup_i2c_poll_state_i2c_master(struct qup_i2c_dev *qup)
|
||
{
|
||
return qup_i2c_poll_state_mask(qup, QUP_I2C_MAST_GEN, QUP_I2C_MAST_GEN);
|
||
}
|
||
|
||
static int qup_i2c_change_state(struct qup_i2c_dev *qup, u32 state)
|
||
{
|
||
if (qup_i2c_poll_state_valid(qup) != 0)
|
||
return -EIO;
|
||
|
||
writel(state, qup->base + QUP_STATE);
|
||
|
||
if (qup_i2c_poll_state(qup, state) != 0)
|
||
return -EIO;
|
||
return 0;
|
||
}
|
||
|
||
/* Check if I2C bus returns to IDLE state */
|
||
static int qup_i2c_bus_active(struct qup_i2c_dev *qup, int len)
|
||
{
|
||
unsigned long timeout;
|
||
u32 status;
|
||
int ret = 0;
|
||
|
||
timeout = jiffies + len * 4;
|
||
for (;;) {
|
||
status = readl(qup->base + QUP_I2C_STATUS);
|
||
if (!(status & I2C_STATUS_BUS_ACTIVE))
|
||
break;
|
||
|
||
if (time_after(jiffies, timeout))
|
||
ret = -ETIMEDOUT;
|
||
|
||
usleep_range(len, len * 2);
|
||
}
|
||
|
||
return ret;
|
||
}
|
||
|
||
static void qup_i2c_write_tx_fifo_v1(struct qup_i2c_dev *qup)
|
||
{
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
struct i2c_msg *msg = qup->msg;
|
||
u32 addr = i2c_8bit_addr_from_msg(msg);
|
||
u32 qup_tag;
|
||
int idx;
|
||
u32 val;
|
||
|
||
if (qup->pos == 0) {
|
||
val = QUP_TAG_START | addr;
|
||
idx = 1;
|
||
blk->tx_fifo_free--;
|
||
} else {
|
||
val = 0;
|
||
idx = 0;
|
||
}
|
||
|
||
while (blk->tx_fifo_free && qup->pos < msg->len) {
|
||
if (qup->pos == msg->len - 1)
|
||
qup_tag = QUP_TAG_STOP;
|
||
else
|
||
qup_tag = QUP_TAG_DATA;
|
||
|
||
if (idx & 1)
|
||
val |= (qup_tag | msg->buf[qup->pos]) << QUP_MSW_SHIFT;
|
||
else
|
||
val = qup_tag | msg->buf[qup->pos];
|
||
|
||
/* Write out the pair and the last odd value */
|
||
if (idx & 1 || qup->pos == msg->len - 1)
|
||
writel(val, qup->base + QUP_OUT_FIFO_BASE);
|
||
|
||
qup->pos++;
|
||
idx++;
|
||
blk->tx_fifo_free--;
|
||
}
|
||
}
|
||
|
||
static void qup_i2c_set_blk_data(struct qup_i2c_dev *qup,
|
||
struct i2c_msg *msg)
|
||
{
|
||
qup->blk.pos = 0;
|
||
qup->blk.data_len = msg->len;
|
||
qup->blk.count = DIV_ROUND_UP(msg->len, qup->blk_xfer_limit);
|
||
}
|
||
|
||
static int qup_i2c_get_data_len(struct qup_i2c_dev *qup)
|
||
{
|
||
int data_len;
|
||
|
||
if (qup->blk.data_len > qup->blk_xfer_limit)
|
||
data_len = qup->blk_xfer_limit;
|
||
else
|
||
data_len = qup->blk.data_len;
|
||
|
||
return data_len;
|
||
}
|
||
|
||
static bool qup_i2c_check_msg_len(struct i2c_msg *msg)
|
||
{
|
||
return ((msg->flags & I2C_M_RD) && (msg->flags & I2C_M_RECV_LEN));
|
||
}
|
||
|
||
static int qup_i2c_set_tags_smb(u16 addr, u8 *tags, struct qup_i2c_dev *qup,
|
||
struct i2c_msg *msg)
|
||
{
|
||
int len = 0;
|
||
|
||
if (qup->is_smbus_read) {
|
||
tags[len++] = QUP_TAG_V2_DATARD_STOP;
|
||
tags[len++] = qup_i2c_get_data_len(qup);
|
||
} else {
|
||
tags[len++] = QUP_TAG_V2_START;
|
||
tags[len++] = addr & 0xff;
|
||
|
||
if (msg->flags & I2C_M_TEN)
|
||
tags[len++] = addr >> 8;
|
||
|
||
tags[len++] = QUP_TAG_V2_DATARD;
|
||
/* Read 1 byte indicating the length of the SMBus message */
|
||
tags[len++] = 1;
|
||
}
|
||
return len;
|
||
}
|
||
|
||
static int qup_i2c_set_tags(u8 *tags, struct qup_i2c_dev *qup,
|
||
struct i2c_msg *msg)
|
||
{
|
||
u16 addr = i2c_8bit_addr_from_msg(msg);
|
||
int len = 0;
|
||
int data_len;
|
||
|
||
int last = (qup->blk.pos == (qup->blk.count - 1)) && (qup->is_last);
|
||
|
||
/* Handle tags for SMBus block read */
|
||
if (qup_i2c_check_msg_len(msg))
|
||
return qup_i2c_set_tags_smb(addr, tags, qup, msg);
|
||
|
||
if (qup->blk.pos == 0) {
|
||
tags[len++] = QUP_TAG_V2_START;
|
||
tags[len++] = addr & 0xff;
|
||
|
||
if (msg->flags & I2C_M_TEN)
|
||
tags[len++] = addr >> 8;
|
||
}
|
||
|
||
/* Send _STOP commands for the last block */
|
||
if (last) {
|
||
if (msg->flags & I2C_M_RD)
|
||
tags[len++] = QUP_TAG_V2_DATARD_STOP;
|
||
else
|
||
tags[len++] = QUP_TAG_V2_DATAWR_STOP;
|
||
} else {
|
||
if (msg->flags & I2C_M_RD)
|
||
tags[len++] = qup->blk.pos == (qup->blk.count - 1) ?
|
||
QUP_TAG_V2_DATARD_NACK :
|
||
QUP_TAG_V2_DATARD;
|
||
else
|
||
tags[len++] = QUP_TAG_V2_DATAWR;
|
||
}
|
||
|
||
data_len = qup_i2c_get_data_len(qup);
|
||
|
||
/* 0 implies 256 bytes */
|
||
if (data_len == QUP_READ_LIMIT)
|
||
tags[len++] = 0;
|
||
else
|
||
tags[len++] = data_len;
|
||
|
||
return len;
|
||
}
|
||
|
||
|
||
static void qup_i2c_bam_cb(void *data)
|
||
{
|
||
struct qup_i2c_dev *qup = data;
|
||
|
||
complete(&qup->xfer);
|
||
}
|
||
|
||
static int qup_sg_set_buf(struct scatterlist *sg, void *buf,
|
||
unsigned int buflen, struct qup_i2c_dev *qup,
|
||
int dir)
|
||
{
|
||
int ret;
|
||
|
||
sg_set_buf(sg, buf, buflen);
|
||
ret = dma_map_sg(qup->dev, sg, 1, dir);
|
||
if (!ret)
|
||
return -EINVAL;
|
||
|
||
return 0;
|
||
}
|
||
|
||
static void qup_i2c_rel_dma(struct qup_i2c_dev *qup)
|
||
{
|
||
if (qup->btx.dma)
|
||
dma_release_channel(qup->btx.dma);
|
||
if (qup->brx.dma)
|
||
dma_release_channel(qup->brx.dma);
|
||
qup->btx.dma = NULL;
|
||
qup->brx.dma = NULL;
|
||
}
|
||
|
||
static int qup_i2c_req_dma(struct qup_i2c_dev *qup)
|
||
{
|
||
int err;
|
||
|
||
if (!qup->btx.dma) {
|
||
qup->btx.dma = dma_request_slave_channel_reason(qup->dev, "tx");
|
||
if (IS_ERR(qup->btx.dma)) {
|
||
err = PTR_ERR(qup->btx.dma);
|
||
qup->btx.dma = NULL;
|
||
dev_err(qup->dev, "\n tx channel not available");
|
||
return err;
|
||
}
|
||
}
|
||
|
||
if (!qup->brx.dma) {
|
||
qup->brx.dma = dma_request_slave_channel_reason(qup->dev, "rx");
|
||
if (IS_ERR(qup->brx.dma)) {
|
||
dev_err(qup->dev, "\n rx channel not available");
|
||
err = PTR_ERR(qup->brx.dma);
|
||
qup->brx.dma = NULL;
|
||
qup_i2c_rel_dma(qup);
|
||
return err;
|
||
}
|
||
}
|
||
return 0;
|
||
}
|
||
|
||
static int qup_i2c_bam_make_desc(struct qup_i2c_dev *qup, struct i2c_msg *msg)
|
||
{
|
||
int ret = 0, limit = QUP_READ_LIMIT;
|
||
u32 len = 0, blocks, rem;
|
||
u32 i = 0, tlen, tx_len = 0;
|
||
u8 *tags;
|
||
|
||
qup->blk_xfer_limit = QUP_READ_LIMIT;
|
||
qup_i2c_set_blk_data(qup, msg);
|
||
|
||
blocks = qup->blk.count;
|
||
rem = msg->len - (blocks - 1) * limit;
|
||
|
||
if (msg->flags & I2C_M_RD) {
|
||
while (qup->blk.pos < blocks) {
|
||
tlen = (i == (blocks - 1)) ? rem : limit;
|
||
tags = &qup->start_tag.start[qup->tag_buf_pos + len];
|
||
len += qup_i2c_set_tags(tags, qup, msg);
|
||
qup->blk.data_len -= tlen;
|
||
|
||
/* scratch buf to read the start and len tags */
|
||
ret = qup_sg_set_buf(&qup->brx.sg[qup->brx.sg_cnt++],
|
||
&qup->brx.tag.start[0],
|
||
2, qup, DMA_FROM_DEVICE);
|
||
|
||
if (ret)
|
||
return ret;
|
||
|
||
ret = qup_sg_set_buf(&qup->brx.sg[qup->brx.sg_cnt++],
|
||
&msg->buf[limit * i],
|
||
tlen, qup,
|
||
DMA_FROM_DEVICE);
|
||
if (ret)
|
||
return ret;
|
||
|
||
i++;
|
||
qup->blk.pos = i;
|
||
}
|
||
ret = qup_sg_set_buf(&qup->btx.sg[qup->btx.sg_cnt++],
|
||
&qup->start_tag.start[qup->tag_buf_pos],
|
||
len, qup, DMA_TO_DEVICE);
|
||
if (ret)
|
||
return ret;
|
||
|
||
qup->tag_buf_pos += len;
|
||
} else {
|
||
while (qup->blk.pos < blocks) {
|
||
tlen = (i == (blocks - 1)) ? rem : limit;
|
||
tags = &qup->start_tag.start[qup->tag_buf_pos + tx_len];
|
||
len = qup_i2c_set_tags(tags, qup, msg);
|
||
qup->blk.data_len -= tlen;
|
||
|
||
ret = qup_sg_set_buf(&qup->btx.sg[qup->btx.sg_cnt++],
|
||
tags, len,
|
||
qup, DMA_TO_DEVICE);
|
||
if (ret)
|
||
return ret;
|
||
|
||
tx_len += len;
|
||
ret = qup_sg_set_buf(&qup->btx.sg[qup->btx.sg_cnt++],
|
||
&msg->buf[limit * i],
|
||
tlen, qup, DMA_TO_DEVICE);
|
||
if (ret)
|
||
return ret;
|
||
i++;
|
||
qup->blk.pos = i;
|
||
}
|
||
|
||
qup->tag_buf_pos += tx_len;
|
||
}
|
||
|
||
return 0;
|
||
}
|
||
|
||
static int qup_i2c_bam_schedule_desc(struct qup_i2c_dev *qup)
|
||
{
|
||
struct dma_async_tx_descriptor *txd, *rxd = NULL;
|
||
int ret = 0;
|
||
dma_cookie_t cookie_rx, cookie_tx;
|
||
u32 len = 0;
|
||
u32 tx_cnt = qup->btx.sg_cnt, rx_cnt = qup->brx.sg_cnt;
|
||
|
||
/* schedule the EOT and FLUSH I2C tags */
|
||
len = 1;
|
||
if (rx_cnt) {
|
||
qup->btx.tag.start[0] = QUP_BAM_INPUT_EOT;
|
||
len++;
|
||
|
||
/* scratch buf to read the BAM EOT FLUSH tags */
|
||
ret = qup_sg_set_buf(&qup->brx.sg[rx_cnt++],
|
||
&qup->brx.tag.start[0],
|
||
1, qup, DMA_FROM_DEVICE);
|
||
if (ret)
|
||
return ret;
|
||
}
|
||
|
||
qup->btx.tag.start[len - 1] = QUP_BAM_FLUSH_STOP;
|
||
ret = qup_sg_set_buf(&qup->btx.sg[tx_cnt++], &qup->btx.tag.start[0],
|
||
len, qup, DMA_TO_DEVICE);
|
||
if (ret)
|
||
return ret;
|
||
|
||
txd = dmaengine_prep_slave_sg(qup->btx.dma, qup->btx.sg, tx_cnt,
|
||
DMA_MEM_TO_DEV,
|
||
DMA_PREP_INTERRUPT | DMA_PREP_FENCE);
|
||
if (!txd) {
|
||
dev_err(qup->dev, "failed to get tx desc\n");
|
||
ret = -EINVAL;
|
||
goto desc_err;
|
||
}
|
||
|
||
if (!rx_cnt) {
|
||
txd->callback = qup_i2c_bam_cb;
|
||
txd->callback_param = qup;
|
||
}
|
||
|
||
cookie_tx = dmaengine_submit(txd);
|
||
if (dma_submit_error(cookie_tx)) {
|
||
ret = -EINVAL;
|
||
goto desc_err;
|
||
}
|
||
|
||
dma_async_issue_pending(qup->btx.dma);
|
||
|
||
if (rx_cnt) {
|
||
rxd = dmaengine_prep_slave_sg(qup->brx.dma, qup->brx.sg,
|
||
rx_cnt, DMA_DEV_TO_MEM,
|
||
DMA_PREP_INTERRUPT);
|
||
if (!rxd) {
|
||
dev_err(qup->dev, "failed to get rx desc\n");
|
||
ret = -EINVAL;
|
||
|
||
/* abort TX descriptors */
|
||
dmaengine_terminate_all(qup->btx.dma);
|
||
goto desc_err;
|
||
}
|
||
|
||
rxd->callback = qup_i2c_bam_cb;
|
||
rxd->callback_param = qup;
|
||
cookie_rx = dmaengine_submit(rxd);
|
||
if (dma_submit_error(cookie_rx)) {
|
||
ret = -EINVAL;
|
||
goto desc_err;
|
||
}
|
||
|
||
dma_async_issue_pending(qup->brx.dma);
|
||
}
|
||
|
||
if (!wait_for_completion_timeout(&qup->xfer, qup->xfer_timeout)) {
|
||
dev_err(qup->dev, "normal trans timed out\n");
|
||
ret = -ETIMEDOUT;
|
||
}
|
||
|
||
if (ret || qup->bus_err || qup->qup_err) {
|
||
reinit_completion(&qup->xfer);
|
||
|
||
if (qup_i2c_change_state(qup, QUP_RUN_STATE)) {
|
||
dev_err(qup->dev, "change to run state timed out");
|
||
goto desc_err;
|
||
}
|
||
|
||
qup_i2c_flush(qup);
|
||
|
||
/* wait for remaining interrupts to occur */
|
||
if (!wait_for_completion_timeout(&qup->xfer, HZ))
|
||
dev_err(qup->dev, "flush timed out\n");
|
||
|
||
ret = (qup->bus_err & QUP_I2C_NACK_FLAG) ? -ENXIO : -EIO;
|
||
}
|
||
|
||
desc_err:
|
||
dma_unmap_sg(qup->dev, qup->btx.sg, tx_cnt, DMA_TO_DEVICE);
|
||
|
||
if (rx_cnt)
|
||
dma_unmap_sg(qup->dev, qup->brx.sg, rx_cnt,
|
||
DMA_FROM_DEVICE);
|
||
|
||
return ret;
|
||
}
|
||
|
||
static void qup_i2c_bam_clear_tag_buffers(struct qup_i2c_dev *qup)
|
||
{
|
||
qup->btx.sg_cnt = 0;
|
||
qup->brx.sg_cnt = 0;
|
||
qup->tag_buf_pos = 0;
|
||
}
|
||
|
||
static int qup_i2c_bam_xfer(struct i2c_adapter *adap, struct i2c_msg *msg,
|
||
int num)
|
||
{
|
||
struct qup_i2c_dev *qup = i2c_get_adapdata(adap);
|
||
int ret = 0;
|
||
int idx = 0;
|
||
|
||
enable_irq(qup->irq);
|
||
ret = qup_i2c_req_dma(qup);
|
||
|
||
if (ret)
|
||
goto out;
|
||
|
||
writel(0, qup->base + QUP_MX_INPUT_CNT);
|
||
writel(0, qup->base + QUP_MX_OUTPUT_CNT);
|
||
|
||
/* set BAM mode */
|
||
writel(QUP_REPACK_EN | QUP_BAM_MODE, qup->base + QUP_IO_MODE);
|
||
|
||
/* mask fifo irqs */
|
||
writel((0x3 << 8), qup->base + QUP_OPERATIONAL_MASK);
|
||
|
||
/* set RUN STATE */
|
||
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
||
if (ret)
|
||
goto out;
|
||
|
||
writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL);
|
||
qup_i2c_bam_clear_tag_buffers(qup);
|
||
|
||
for (idx = 0; idx < num; idx++) {
|
||
qup->msg = msg + idx;
|
||
qup->is_last = idx == (num - 1);
|
||
|
||
ret = qup_i2c_bam_make_desc(qup, qup->msg);
|
||
if (ret)
|
||
break;
|
||
|
||
/*
|
||
* Make DMA descriptor and schedule the BAM transfer if its
|
||
* already crossed the maximum length. Since the memory for all
|
||
* tags buffers have been taken for 2 maximum possible
|
||
* transfers length so it will never cross the buffer actual
|
||
* length.
|
||
*/
|
||
if (qup->btx.sg_cnt > qup->max_xfer_sg_len ||
|
||
qup->brx.sg_cnt > qup->max_xfer_sg_len ||
|
||
qup->is_last) {
|
||
ret = qup_i2c_bam_schedule_desc(qup);
|
||
if (ret)
|
||
break;
|
||
|
||
qup_i2c_bam_clear_tag_buffers(qup);
|
||
}
|
||
}
|
||
|
||
out:
|
||
disable_irq(qup->irq);
|
||
|
||
qup->msg = NULL;
|
||
return ret;
|
||
}
|
||
|
||
static int qup_i2c_wait_for_complete(struct qup_i2c_dev *qup,
|
||
struct i2c_msg *msg)
|
||
{
|
||
unsigned long left;
|
||
int ret = 0;
|
||
|
||
left = wait_for_completion_timeout(&qup->xfer, qup->xfer_timeout);
|
||
if (!left) {
|
||
writel(1, qup->base + QUP_SW_RESET);
|
||
ret = -ETIMEDOUT;
|
||
}
|
||
|
||
if (qup->bus_err || qup->qup_err)
|
||
ret = (qup->bus_err & QUP_I2C_NACK_FLAG) ? -ENXIO : -EIO;
|
||
|
||
return ret;
|
||
}
|
||
|
||
static void qup_i2c_read_rx_fifo_v1(struct qup_i2c_dev *qup)
|
||
{
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
struct i2c_msg *msg = qup->msg;
|
||
u32 val = 0;
|
||
int idx = 0;
|
||
|
||
while (blk->fifo_available && qup->pos < msg->len) {
|
||
if ((idx & 1) == 0) {
|
||
/* Reading 2 words at time */
|
||
val = readl(qup->base + QUP_IN_FIFO_BASE);
|
||
msg->buf[qup->pos++] = val & 0xFF;
|
||
} else {
|
||
msg->buf[qup->pos++] = val >> QUP_MSW_SHIFT;
|
||
}
|
||
idx++;
|
||
blk->fifo_available--;
|
||
}
|
||
|
||
if (qup->pos == msg->len)
|
||
blk->rx_bytes_read = true;
|
||
}
|
||
|
||
static void qup_i2c_write_rx_tags_v1(struct qup_i2c_dev *qup)
|
||
{
|
||
struct i2c_msg *msg = qup->msg;
|
||
u32 addr, len, val;
|
||
|
||
addr = i2c_8bit_addr_from_msg(msg);
|
||
|
||
/* 0 is used to specify a length 256 (QUP_READ_LIMIT) */
|
||
len = (msg->len == QUP_READ_LIMIT) ? 0 : msg->len;
|
||
|
||
val = ((QUP_TAG_REC | len) << QUP_MSW_SHIFT) | QUP_TAG_START | addr;
|
||
writel(val, qup->base + QUP_OUT_FIFO_BASE);
|
||
}
|
||
|
||
static void qup_i2c_conf_v1(struct qup_i2c_dev *qup)
|
||
{
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
u32 qup_config = I2C_MINI_CORE | I2C_N_VAL;
|
||
u32 io_mode = QUP_REPACK_EN;
|
||
|
||
blk->is_tx_blk_mode =
|
||
blk->total_tx_len > qup->out_fifo_sz ? true : false;
|
||
blk->is_rx_blk_mode =
|
||
blk->total_rx_len > qup->in_fifo_sz ? true : false;
|
||
|
||
if (blk->is_tx_blk_mode) {
|
||
io_mode |= QUP_OUTPUT_BLK_MODE;
|
||
writel(0, qup->base + QUP_MX_WRITE_CNT);
|
||
writel(blk->total_tx_len, qup->base + QUP_MX_OUTPUT_CNT);
|
||
} else {
|
||
writel(0, qup->base + QUP_MX_OUTPUT_CNT);
|
||
writel(blk->total_tx_len, qup->base + QUP_MX_WRITE_CNT);
|
||
}
|
||
|
||
if (blk->total_rx_len) {
|
||
if (blk->is_rx_blk_mode) {
|
||
io_mode |= QUP_INPUT_BLK_MODE;
|
||
writel(0, qup->base + QUP_MX_READ_CNT);
|
||
writel(blk->total_rx_len, qup->base + QUP_MX_INPUT_CNT);
|
||
} else {
|
||
writel(0, qup->base + QUP_MX_INPUT_CNT);
|
||
writel(blk->total_rx_len, qup->base + QUP_MX_READ_CNT);
|
||
}
|
||
} else {
|
||
qup_config |= QUP_NO_INPUT;
|
||
}
|
||
|
||
writel(qup_config, qup->base + QUP_CONFIG);
|
||
writel(io_mode, qup->base + QUP_IO_MODE);
|
||
}
|
||
|
||
static void qup_i2c_clear_blk_v1(struct qup_i2c_block *blk)
|
||
{
|
||
blk->tx_fifo_free = 0;
|
||
blk->fifo_available = 0;
|
||
blk->rx_bytes_read = false;
|
||
}
|
||
|
||
static int qup_i2c_conf_xfer_v1(struct qup_i2c_dev *qup, bool is_rx)
|
||
{
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
int ret;
|
||
|
||
qup_i2c_clear_blk_v1(blk);
|
||
qup_i2c_conf_v1(qup);
|
||
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
||
if (ret)
|
||
return ret;
|
||
|
||
writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL);
|
||
|
||
ret = qup_i2c_change_state(qup, QUP_PAUSE_STATE);
|
||
if (ret)
|
||
return ret;
|
||
|
||
reinit_completion(&qup->xfer);
|
||
enable_irq(qup->irq);
|
||
if (!blk->is_tx_blk_mode) {
|
||
blk->tx_fifo_free = qup->out_fifo_sz;
|
||
|
||
if (is_rx)
|
||
qup_i2c_write_rx_tags_v1(qup);
|
||
else
|
||
qup_i2c_write_tx_fifo_v1(qup);
|
||
}
|
||
|
||
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
||
if (ret)
|
||
goto err;
|
||
|
||
ret = qup_i2c_wait_for_complete(qup, qup->msg);
|
||
if (ret)
|
||
goto err;
|
||
|
||
ret = qup_i2c_bus_active(qup, ONE_BYTE);
|
||
|
||
err:
|
||
disable_irq(qup->irq);
|
||
return ret;
|
||
}
|
||
|
||
static int qup_i2c_write_one(struct qup_i2c_dev *qup)
|
||
{
|
||
struct i2c_msg *msg = qup->msg;
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
|
||
qup->pos = 0;
|
||
blk->total_tx_len = msg->len + 1;
|
||
blk->total_rx_len = 0;
|
||
|
||
return qup_i2c_conf_xfer_v1(qup, false);
|
||
}
|
||
|
||
static int qup_i2c_read_one(struct qup_i2c_dev *qup)
|
||
{
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
|
||
qup->pos = 0;
|
||
blk->total_tx_len = 2;
|
||
blk->total_rx_len = qup->msg->len;
|
||
|
||
return qup_i2c_conf_xfer_v1(qup, true);
|
||
}
|
||
|
||
static int qup_i2c_xfer(struct i2c_adapter *adap,
|
||
struct i2c_msg msgs[],
|
||
int num)
|
||
{
|
||
struct qup_i2c_dev *qup = i2c_get_adapdata(adap);
|
||
int ret, idx;
|
||
|
||
ret = pm_runtime_get_sync(qup->dev);
|
||
if (ret < 0)
|
||
goto out;
|
||
|
||
qup->bus_err = 0;
|
||
qup->qup_err = 0;
|
||
|
||
writel(1, qup->base + QUP_SW_RESET);
|
||
ret = qup_i2c_poll_state(qup, QUP_RESET_STATE);
|
||
if (ret)
|
||
goto out;
|
||
|
||
/* Configure QUP as I2C mini core */
|
||
writel(I2C_MINI_CORE | I2C_N_VAL, qup->base + QUP_CONFIG);
|
||
|
||
for (idx = 0; idx < num; idx++) {
|
||
if (qup_i2c_poll_state_i2c_master(qup)) {
|
||
ret = -EIO;
|
||
goto out;
|
||
}
|
||
|
||
if (qup_i2c_check_msg_len(&msgs[idx])) {
|
||
ret = -EINVAL;
|
||
goto out;
|
||
}
|
||
|
||
qup->msg = &msgs[idx];
|
||
if (msgs[idx].flags & I2C_M_RD)
|
||
ret = qup_i2c_read_one(qup);
|
||
else
|
||
ret = qup_i2c_write_one(qup);
|
||
|
||
if (ret)
|
||
break;
|
||
|
||
ret = qup_i2c_change_state(qup, QUP_RESET_STATE);
|
||
if (ret)
|
||
break;
|
||
}
|
||
|
||
if (ret == 0)
|
||
ret = num;
|
||
out:
|
||
|
||
pm_runtime_mark_last_busy(qup->dev);
|
||
pm_runtime_put_autosuspend(qup->dev);
|
||
|
||
return ret;
|
||
}
|
||
|
||
/*
|
||
* Configure registers related with reconfiguration during run and call it
|
||
* before each i2c sub transfer.
|
||
*/
|
||
static void qup_i2c_conf_count_v2(struct qup_i2c_dev *qup)
|
||
{
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
u32 qup_config = I2C_MINI_CORE | I2C_N_VAL_V2;
|
||
|
||
if (blk->is_tx_blk_mode)
|
||
writel(qup->config_run | blk->total_tx_len,
|
||
qup->base + QUP_MX_OUTPUT_CNT);
|
||
else
|
||
writel(qup->config_run | blk->total_tx_len,
|
||
qup->base + QUP_MX_WRITE_CNT);
|
||
|
||
if (blk->total_rx_len) {
|
||
if (blk->is_rx_blk_mode)
|
||
writel(qup->config_run | blk->total_rx_len,
|
||
qup->base + QUP_MX_INPUT_CNT);
|
||
else
|
||
writel(qup->config_run | blk->total_rx_len,
|
||
qup->base + QUP_MX_READ_CNT);
|
||
} else {
|
||
qup_config |= QUP_NO_INPUT;
|
||
}
|
||
|
||
writel(qup_config, qup->base + QUP_CONFIG);
|
||
}
|
||
|
||
/*
|
||
* Configure registers related with transfer mode (FIFO/Block)
|
||
* before starting of i2c transfer. It will be called only once in
|
||
* QUP RESET state.
|
||
*/
|
||
static void qup_i2c_conf_mode_v2(struct qup_i2c_dev *qup)
|
||
{
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
u32 io_mode = QUP_REPACK_EN;
|
||
|
||
if (blk->is_tx_blk_mode) {
|
||
io_mode |= QUP_OUTPUT_BLK_MODE;
|
||
writel(0, qup->base + QUP_MX_WRITE_CNT);
|
||
} else {
|
||
writel(0, qup->base + QUP_MX_OUTPUT_CNT);
|
||
}
|
||
|
||
if (blk->is_rx_blk_mode) {
|
||
io_mode |= QUP_INPUT_BLK_MODE;
|
||
writel(0, qup->base + QUP_MX_READ_CNT);
|
||
} else {
|
||
writel(0, qup->base + QUP_MX_INPUT_CNT);
|
||
}
|
||
|
||
writel(io_mode, qup->base + QUP_IO_MODE);
|
||
}
|
||
|
||
/* Clear required variables before starting of any QUP v2 sub transfer. */
|
||
static void qup_i2c_clear_blk_v2(struct qup_i2c_block *blk)
|
||
{
|
||
blk->send_last_word = false;
|
||
blk->tx_tags_sent = false;
|
||
blk->tx_fifo_data = 0;
|
||
blk->tx_fifo_data_pos = 0;
|
||
blk->tx_fifo_free = 0;
|
||
|
||
blk->rx_tags_fetched = false;
|
||
blk->rx_bytes_read = false;
|
||
blk->rx_fifo_data = 0;
|
||
blk->rx_fifo_data_pos = 0;
|
||
blk->fifo_available = 0;
|
||
}
|
||
|
||
/* Receive data from RX FIFO for read message in QUP v2 i2c transfer. */
|
||
static void qup_i2c_recv_data(struct qup_i2c_dev *qup)
|
||
{
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
int j;
|
||
|
||
for (j = blk->rx_fifo_data_pos;
|
||
blk->cur_blk_len && blk->fifo_available;
|
||
blk->cur_blk_len--, blk->fifo_available--) {
|
||
if (j == 0)
|
||
blk->rx_fifo_data = readl(qup->base + QUP_IN_FIFO_BASE);
|
||
|
||
*(blk->cur_data++) = blk->rx_fifo_data;
|
||
blk->rx_fifo_data >>= 8;
|
||
|
||
if (j == 3)
|
||
j = 0;
|
||
else
|
||
j++;
|
||
}
|
||
|
||
blk->rx_fifo_data_pos = j;
|
||
}
|
||
|
||
/* Receive tags for read message in QUP v2 i2c transfer. */
|
||
static void qup_i2c_recv_tags(struct qup_i2c_dev *qup)
|
||
{
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
|
||
blk->rx_fifo_data = readl(qup->base + QUP_IN_FIFO_BASE);
|
||
blk->rx_fifo_data >>= blk->rx_tag_len * 8;
|
||
blk->rx_fifo_data_pos = blk->rx_tag_len;
|
||
blk->fifo_available -= blk->rx_tag_len;
|
||
}
|
||
|
||
/*
|
||
* Read the data and tags from RX FIFO. Since in read case, the tags will be
|
||
* preceded by received data bytes so
|
||
* 1. Check if rx_tags_fetched is false i.e. the start of QUP block so receive
|
||
* all tag bytes and discard that.
|
||
* 2. Read the data from RX FIFO. When all the data bytes have been read then
|
||
* set rx_bytes_read to true.
|
||
*/
|
||
static void qup_i2c_read_rx_fifo_v2(struct qup_i2c_dev *qup)
|
||
{
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
|
||
if (!blk->rx_tags_fetched) {
|
||
qup_i2c_recv_tags(qup);
|
||
blk->rx_tags_fetched = true;
|
||
}
|
||
|
||
qup_i2c_recv_data(qup);
|
||
if (!blk->cur_blk_len)
|
||
blk->rx_bytes_read = true;
|
||
}
|
||
|
||
/*
|
||
* Write bytes in TX FIFO for write message in QUP v2 i2c transfer. QUP TX FIFO
|
||
* write works on word basis (4 bytes). Append new data byte write for TX FIFO
|
||
* in tx_fifo_data and write to TX FIFO when all the 4 bytes are present.
|
||
*/
|
||
static void
|
||
qup_i2c_write_blk_data(struct qup_i2c_dev *qup, u8 **data, unsigned int *len)
|
||
{
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
unsigned int j;
|
||
|
||
for (j = blk->tx_fifo_data_pos; *len && blk->tx_fifo_free;
|
||
(*len)--, blk->tx_fifo_free--) {
|
||
blk->tx_fifo_data |= *(*data)++ << (j * 8);
|
||
if (j == 3) {
|
||
writel(blk->tx_fifo_data,
|
||
qup->base + QUP_OUT_FIFO_BASE);
|
||
blk->tx_fifo_data = 0x0;
|
||
j = 0;
|
||
} else {
|
||
j++;
|
||
}
|
||
}
|
||
|
||
blk->tx_fifo_data_pos = j;
|
||
}
|
||
|
||
/* Transfer tags for read message in QUP v2 i2c transfer. */
|
||
static void qup_i2c_write_rx_tags_v2(struct qup_i2c_dev *qup)
|
||
{
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
|
||
qup_i2c_write_blk_data(qup, &blk->cur_tx_tags, &blk->tx_tag_len);
|
||
if (blk->tx_fifo_data_pos)
|
||
writel(blk->tx_fifo_data, qup->base + QUP_OUT_FIFO_BASE);
|
||
}
|
||
|
||
/*
|
||
* Write the data and tags in TX FIFO. Since in write case, both tags and data
|
||
* need to be written and QUP write tags can have maximum 256 data length, so
|
||
*
|
||
* 1. Check if tx_tags_sent is false i.e. the start of QUP block so write the
|
||
* tags to TX FIFO and set tx_tags_sent to true.
|
||
* 2. Check if send_last_word is true. It will be set when last few data bytes
|
||
* (less than 4 bytes) are reamining to be written in FIFO because of no FIFO
|
||
* space. All this data bytes are available in tx_fifo_data so write this
|
||
* in FIFO.
|
||
* 3. Write the data to TX FIFO and check for cur_blk_len. If it is non zero
|
||
* then more data is pending otherwise following 3 cases can be possible
|
||
* a. if tx_fifo_data_pos is zero i.e. all the data bytes in this block
|
||
* have been written in TX FIFO so nothing else is required.
|
||
* b. tx_fifo_free is non zero i.e tx FIFO is free so copy the remaining data
|
||
* from tx_fifo_data to tx FIFO. Since, qup_i2c_write_blk_data do write
|
||
* in 4 bytes and FIFO space is in multiple of 4 bytes so tx_fifo_free
|
||
* will be always greater than or equal to 4 bytes.
|
||
* c. tx_fifo_free is zero. In this case, last few bytes (less than 4
|
||
* bytes) are copied to tx_fifo_data but couldn't be sent because of
|
||
* FIFO full so make send_last_word true.
|
||
*/
|
||
static void qup_i2c_write_tx_fifo_v2(struct qup_i2c_dev *qup)
|
||
{
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
|
||
if (!blk->tx_tags_sent) {
|
||
qup_i2c_write_blk_data(qup, &blk->cur_tx_tags,
|
||
&blk->tx_tag_len);
|
||
blk->tx_tags_sent = true;
|
||
}
|
||
|
||
if (blk->send_last_word)
|
||
goto send_last_word;
|
||
|
||
qup_i2c_write_blk_data(qup, &blk->cur_data, &blk->cur_blk_len);
|
||
if (!blk->cur_blk_len) {
|
||
if (!blk->tx_fifo_data_pos)
|
||
return;
|
||
|
||
if (blk->tx_fifo_free)
|
||
goto send_last_word;
|
||
|
||
blk->send_last_word = true;
|
||
}
|
||
|
||
return;
|
||
|
||
send_last_word:
|
||
writel(blk->tx_fifo_data, qup->base + QUP_OUT_FIFO_BASE);
|
||
}
|
||
|
||
/*
|
||
* Main transfer function which read or write i2c data.
|
||
* The QUP v2 supports reconfiguration during run in which multiple i2c sub
|
||
* transfers can be scheduled.
|
||
*/
|
||
static int
|
||
qup_i2c_conf_xfer_v2(struct qup_i2c_dev *qup, bool is_rx, bool is_first,
|
||
bool change_pause_state)
|
||
{
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
struct i2c_msg *msg = qup->msg;
|
||
int ret;
|
||
|
||
/*
|
||
* Check if its SMBus Block read for which the top level read will be
|
||
* done into 2 QUP reads. One with message length 1 while other one is
|
||
* with actual length.
|
||
*/
|
||
if (qup_i2c_check_msg_len(msg)) {
|
||
if (qup->is_smbus_read) {
|
||
/*
|
||
* If the message length is already read in
|
||
* the first byte of the buffer, account for
|
||
* that by setting the offset
|
||
*/
|
||
blk->cur_data += 1;
|
||
is_first = false;
|
||
} else {
|
||
change_pause_state = false;
|
||
}
|
||
}
|
||
|
||
qup->config_run = is_first ? 0 : QUP_I2C_MX_CONFIG_DURING_RUN;
|
||
|
||
qup_i2c_clear_blk_v2(blk);
|
||
qup_i2c_conf_count_v2(qup);
|
||
|
||
/* If it is first sub transfer, then configure i2c bus clocks */
|
||
if (is_first) {
|
||
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
||
if (ret)
|
||
return ret;
|
||
|
||
writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL);
|
||
|
||
ret = qup_i2c_change_state(qup, QUP_PAUSE_STATE);
|
||
if (ret)
|
||
return ret;
|
||
}
|
||
|
||
reinit_completion(&qup->xfer);
|
||
enable_irq(qup->irq);
|
||
/*
|
||
* In FIFO mode, tx FIFO can be written directly while in block mode the
|
||
* it will be written after getting OUT_BLOCK_WRITE_REQ interrupt
|
||
*/
|
||
if (!blk->is_tx_blk_mode) {
|
||
blk->tx_fifo_free = qup->out_fifo_sz;
|
||
|
||
if (is_rx)
|
||
qup_i2c_write_rx_tags_v2(qup);
|
||
else
|
||
qup_i2c_write_tx_fifo_v2(qup);
|
||
}
|
||
|
||
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
||
if (ret)
|
||
goto err;
|
||
|
||
ret = qup_i2c_wait_for_complete(qup, msg);
|
||
if (ret)
|
||
goto err;
|
||
|
||
/* Move to pause state for all the transfers, except last one */
|
||
if (change_pause_state) {
|
||
ret = qup_i2c_change_state(qup, QUP_PAUSE_STATE);
|
||
if (ret)
|
||
goto err;
|
||
}
|
||
|
||
err:
|
||
disable_irq(qup->irq);
|
||
return ret;
|
||
}
|
||
|
||
/*
|
||
* Transfer one read/write message in i2c transfer. It splits the message into
|
||
* multiple of blk_xfer_limit data length blocks and schedule each
|
||
* QUP block individually.
|
||
*/
|
||
static int qup_i2c_xfer_v2_msg(struct qup_i2c_dev *qup, int msg_id, bool is_rx)
|
||
{
|
||
int ret = 0;
|
||
unsigned int data_len, i;
|
||
struct i2c_msg *msg = qup->msg;
|
||
struct qup_i2c_block *blk = &qup->blk;
|
||
u8 *msg_buf = msg->buf;
|
||
|
||
qup->blk_xfer_limit = is_rx ? RECV_MAX_DATA_LEN : QUP_READ_LIMIT;
|
||
qup_i2c_set_blk_data(qup, msg);
|
||
|
||
for (i = 0; i < blk->count; i++) {
|
||
data_len = qup_i2c_get_data_len(qup);
|
||
blk->pos = i;
|
||
blk->cur_tx_tags = blk->tags;
|
||
blk->cur_blk_len = data_len;
|
||
blk->tx_tag_len =
|
||
qup_i2c_set_tags(blk->cur_tx_tags, qup, qup->msg);
|
||
|
||
blk->cur_data = msg_buf;
|
||
|
||
if (is_rx) {
|
||
blk->total_tx_len = blk->tx_tag_len;
|
||
blk->rx_tag_len = 2;
|
||
blk->total_rx_len = blk->rx_tag_len + data_len;
|
||
} else {
|
||
blk->total_tx_len = blk->tx_tag_len + data_len;
|
||
blk->total_rx_len = 0;
|
||
}
|
||
|
||
ret = qup_i2c_conf_xfer_v2(qup, is_rx, !msg_id && !i,
|
||
!qup->is_last || i < blk->count - 1);
|
||
if (ret)
|
||
return ret;
|
||
|
||
/* Handle SMBus block read length */
|
||
if (qup_i2c_check_msg_len(msg) && msg->len == 1 &&
|
||
!qup->is_smbus_read) {
|
||
if (msg->buf[0] > I2C_SMBUS_BLOCK_MAX)
|
||
return -EPROTO;
|
||
|
||
msg->len = msg->buf[0];
|
||
qup->is_smbus_read = true;
|
||
ret = qup_i2c_xfer_v2_msg(qup, msg_id, true);
|
||
qup->is_smbus_read = false;
|
||
if (ret)
|
||
return ret;
|
||
|
||
msg->len += 1;
|
||
}
|
||
|
||
msg_buf += data_len;
|
||
blk->data_len -= qup->blk_xfer_limit;
|
||
}
|
||
|
||
return ret;
|
||
}
|
||
|
||
/*
|
||
* QUP v2 supports 3 modes
|
||
* Programmed IO using FIFO mode : Less than FIFO size
|
||
* Programmed IO using Block mode : Greater than FIFO size
|
||
* DMA using BAM : Appropriate for any transaction size but the address should
|
||
* be DMA applicable
|
||
*
|
||
* This function determines the mode which will be used for this transfer. An
|
||
* i2c transfer contains multiple message. Following are the rules to determine
|
||
* the mode used.
|
||
* 1. Determine complete length, maximum tx and rx length for complete transfer.
|
||
* 2. If complete transfer length is greater than fifo size then use the DMA
|
||
* mode.
|
||
* 3. In FIFO or block mode, tx and rx can operate in different mode so check
|
||
* for maximum tx and rx length to determine mode.
|
||
*/
|
||
static int
|
||
qup_i2c_determine_mode_v2(struct qup_i2c_dev *qup,
|
||
struct i2c_msg msgs[], int num)
|
||
{
|
||
int idx;
|
||
bool no_dma = false;
|
||
unsigned int max_tx_len = 0, max_rx_len = 0, total_len = 0;
|
||
|
||
/* All i2c_msgs should be transferred using either dma or cpu */
|
||
for (idx = 0; idx < num; idx++) {
|
||
if (msgs[idx].flags & I2C_M_RD)
|
||
max_rx_len = max_t(unsigned int, max_rx_len,
|
||
msgs[idx].len);
|
||
else
|
||
max_tx_len = max_t(unsigned int, max_tx_len,
|
||
msgs[idx].len);
|
||
|
||
if (is_vmalloc_addr(msgs[idx].buf))
|
||
no_dma = true;
|
||
|
||
total_len += msgs[idx].len;
|
||
}
|
||
|
||
if (!no_dma && qup->is_dma &&
|
||
(total_len > qup->out_fifo_sz || total_len > qup->in_fifo_sz)) {
|
||
qup->use_dma = true;
|
||
} else {
|
||
qup->blk.is_tx_blk_mode = max_tx_len > qup->out_fifo_sz -
|
||
QUP_MAX_TAGS_LEN ? true : false;
|
||
qup->blk.is_rx_blk_mode = max_rx_len > qup->in_fifo_sz -
|
||
READ_RX_TAGS_LEN ? true : false;
|
||
}
|
||
|
||
return 0;
|
||
}
|
||
|
||
static int qup_i2c_xfer_v2(struct i2c_adapter *adap,
|
||
struct i2c_msg msgs[],
|
||
int num)
|
||
{
|
||
struct qup_i2c_dev *qup = i2c_get_adapdata(adap);
|
||
int ret, idx = 0;
|
||
|
||
qup->bus_err = 0;
|
||
qup->qup_err = 0;
|
||
|
||
ret = pm_runtime_get_sync(qup->dev);
|
||
if (ret < 0)
|
||
goto out;
|
||
|
||
ret = qup_i2c_determine_mode_v2(qup, msgs, num);
|
||
if (ret)
|
||
goto out;
|
||
|
||
writel(1, qup->base + QUP_SW_RESET);
|
||
ret = qup_i2c_poll_state(qup, QUP_RESET_STATE);
|
||
if (ret)
|
||
goto out;
|
||
|
||
/* Configure QUP as I2C mini core */
|
||
writel(I2C_MINI_CORE | I2C_N_VAL_V2, qup->base + QUP_CONFIG);
|
||
writel(QUP_V2_TAGS_EN, qup->base + QUP_I2C_MASTER_GEN);
|
||
|
||
if (qup_i2c_poll_state_i2c_master(qup)) {
|
||
ret = -EIO;
|
||
goto out;
|
||
}
|
||
|
||
if (qup->use_dma) {
|
||
reinit_completion(&qup->xfer);
|
||
ret = qup_i2c_bam_xfer(adap, &msgs[0], num);
|
||
qup->use_dma = false;
|
||
} else {
|
||
qup_i2c_conf_mode_v2(qup);
|
||
|
||
for (idx = 0; idx < num; idx++) {
|
||
qup->msg = &msgs[idx];
|
||
qup->is_last = idx == (num - 1);
|
||
|
||
ret = qup_i2c_xfer_v2_msg(qup, idx,
|
||
!!(msgs[idx].flags & I2C_M_RD));
|
||
if (ret)
|
||
break;
|
||
}
|
||
qup->msg = NULL;
|
||
}
|
||
|
||
if (!ret)
|
||
ret = qup_i2c_bus_active(qup, ONE_BYTE);
|
||
|
||
if (!ret)
|
||
qup_i2c_change_state(qup, QUP_RESET_STATE);
|
||
|
||
if (ret == 0)
|
||
ret = num;
|
||
out:
|
||
pm_runtime_mark_last_busy(qup->dev);
|
||
pm_runtime_put_autosuspend(qup->dev);
|
||
|
||
return ret;
|
||
}
|
||
|
||
static u32 qup_i2c_func(struct i2c_adapter *adap)
|
||
{
|
||
return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK);
|
||
}
|
||
|
||
static const struct i2c_algorithm qup_i2c_algo = {
|
||
.master_xfer = qup_i2c_xfer,
|
||
.functionality = qup_i2c_func,
|
||
};
|
||
|
||
static const struct i2c_algorithm qup_i2c_algo_v2 = {
|
||
.master_xfer = qup_i2c_xfer_v2,
|
||
.functionality = qup_i2c_func,
|
||
};
|
||
|
||
/*
|
||
* The QUP block will issue a NACK and STOP on the bus when reaching
|
||
* the end of the read, the length of the read is specified as one byte
|
||
* which limits the possible read to 256 (QUP_READ_LIMIT) bytes.
|
||
*/
|
||
static const struct i2c_adapter_quirks qup_i2c_quirks = {
|
||
.flags = I2C_AQ_NO_ZERO_LEN,
|
||
.max_read_len = QUP_READ_LIMIT,
|
||
};
|
||
|
||
static const struct i2c_adapter_quirks qup_i2c_quirks_v2 = {
|
||
.flags = I2C_AQ_NO_ZERO_LEN,
|
||
};
|
||
|
||
static void qup_i2c_enable_clocks(struct qup_i2c_dev *qup)
|
||
{
|
||
clk_prepare_enable(qup->clk);
|
||
clk_prepare_enable(qup->pclk);
|
||
}
|
||
|
||
static void qup_i2c_disable_clocks(struct qup_i2c_dev *qup)
|
||
{
|
||
u32 config;
|
||
|
||
qup_i2c_change_state(qup, QUP_RESET_STATE);
|
||
clk_disable_unprepare(qup->clk);
|
||
config = readl(qup->base + QUP_CONFIG);
|
||
config |= QUP_CLOCK_AUTO_GATE;
|
||
writel(config, qup->base + QUP_CONFIG);
|
||
clk_disable_unprepare(qup->pclk);
|
||
}
|
||
|
||
static const struct acpi_device_id qup_i2c_acpi_match[] = {
|
||
{ "QCOM8010"},
|
||
{ },
|
||
};
|
||
MODULE_DEVICE_TABLE(acpi, qup_i2c_acpi_match);
|
||
|
||
static int qup_i2c_probe(struct platform_device *pdev)
|
||
{
|
||
static const int blk_sizes[] = {4, 16, 32};
|
||
struct qup_i2c_dev *qup;
|
||
unsigned long one_bit_t;
|
||
struct resource *res;
|
||
u32 io_mode, hw_ver, size;
|
||
int ret, fs_div, hs_div;
|
||
u32 src_clk_freq = DEFAULT_SRC_CLK;
|
||
u32 clk_freq = DEFAULT_CLK_FREQ;
|
||
int blocks;
|
||
bool is_qup_v1;
|
||
|
||
qup = devm_kzalloc(&pdev->dev, sizeof(*qup), GFP_KERNEL);
|
||
if (!qup)
|
||
return -ENOMEM;
|
||
|
||
qup->dev = &pdev->dev;
|
||
init_completion(&qup->xfer);
|
||
platform_set_drvdata(pdev, qup);
|
||
|
||
if (scl_freq) {
|
||
dev_notice(qup->dev, "Using override frequency of %u\n", scl_freq);
|
||
clk_freq = scl_freq;
|
||
} else {
|
||
ret = device_property_read_u32(qup->dev, "clock-frequency", &clk_freq);
|
||
if (ret) {
|
||
dev_notice(qup->dev, "using default clock-frequency %d",
|
||
DEFAULT_CLK_FREQ);
|
||
}
|
||
}
|
||
|
||
if (of_device_is_compatible(pdev->dev.of_node, "qcom,i2c-qup-v1.1.1")) {
|
||
qup->adap.algo = &qup_i2c_algo;
|
||
qup->adap.quirks = &qup_i2c_quirks;
|
||
is_qup_v1 = true;
|
||
} else {
|
||
qup->adap.algo = &qup_i2c_algo_v2;
|
||
qup->adap.quirks = &qup_i2c_quirks_v2;
|
||
is_qup_v1 = false;
|
||
if (acpi_match_device(qup_i2c_acpi_match, qup->dev))
|
||
goto nodma;
|
||
else
|
||
ret = qup_i2c_req_dma(qup);
|
||
|
||
if (ret == -EPROBE_DEFER)
|
||
goto fail_dma;
|
||
else if (ret != 0)
|
||
goto nodma;
|
||
|
||
qup->max_xfer_sg_len = (MX_BLOCKS << 1);
|
||
blocks = (MX_DMA_BLOCKS << 1) + 1;
|
||
qup->btx.sg = devm_kcalloc(&pdev->dev,
|
||
blocks, sizeof(*qup->btx.sg),
|
||
GFP_KERNEL);
|
||
if (!qup->btx.sg) {
|
||
ret = -ENOMEM;
|
||
goto fail_dma;
|
||
}
|
||
sg_init_table(qup->btx.sg, blocks);
|
||
|
||
qup->brx.sg = devm_kcalloc(&pdev->dev,
|
||
blocks, sizeof(*qup->brx.sg),
|
||
GFP_KERNEL);
|
||
if (!qup->brx.sg) {
|
||
ret = -ENOMEM;
|
||
goto fail_dma;
|
||
}
|
||
sg_init_table(qup->brx.sg, blocks);
|
||
|
||
/* 2 tag bytes for each block + 5 for start, stop tags */
|
||
size = blocks * 2 + 5;
|
||
|
||
qup->start_tag.start = devm_kzalloc(&pdev->dev,
|
||
size, GFP_KERNEL);
|
||
if (!qup->start_tag.start) {
|
||
ret = -ENOMEM;
|
||
goto fail_dma;
|
||
}
|
||
|
||
qup->brx.tag.start = devm_kzalloc(&pdev->dev, 2, GFP_KERNEL);
|
||
if (!qup->brx.tag.start) {
|
||
ret = -ENOMEM;
|
||
goto fail_dma;
|
||
}
|
||
|
||
qup->btx.tag.start = devm_kzalloc(&pdev->dev, 2, GFP_KERNEL);
|
||
if (!qup->btx.tag.start) {
|
||
ret = -ENOMEM;
|
||
goto fail_dma;
|
||
}
|
||
qup->is_dma = true;
|
||
}
|
||
|
||
nodma:
|
||
/* We support frequencies up to FAST Mode Plus (1MHz) */
|
||
if (!clk_freq || clk_freq > I2C_FAST_MODE_PLUS_FREQ) {
|
||
dev_err(qup->dev, "clock frequency not supported %d\n",
|
||
clk_freq);
|
||
return -EINVAL;
|
||
}
|
||
|
||
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
||
qup->base = devm_ioremap_resource(qup->dev, res);
|
||
if (IS_ERR(qup->base))
|
||
return PTR_ERR(qup->base);
|
||
|
||
qup->irq = platform_get_irq(pdev, 0);
|
||
if (qup->irq < 0) {
|
||
dev_err(qup->dev, "No IRQ defined\n");
|
||
return qup->irq;
|
||
}
|
||
|
||
if (has_acpi_companion(qup->dev)) {
|
||
ret = device_property_read_u32(qup->dev,
|
||
"src-clock-hz", &src_clk_freq);
|
||
if (ret) {
|
||
dev_notice(qup->dev, "using default src-clock-hz %d",
|
||
DEFAULT_SRC_CLK);
|
||
}
|
||
ACPI_COMPANION_SET(&qup->adap.dev, ACPI_COMPANION(qup->dev));
|
||
} else {
|
||
qup->clk = devm_clk_get(qup->dev, "core");
|
||
if (IS_ERR(qup->clk)) {
|
||
dev_err(qup->dev, "Could not get core clock\n");
|
||
return PTR_ERR(qup->clk);
|
||
}
|
||
|
||
qup->pclk = devm_clk_get(qup->dev, "iface");
|
||
if (IS_ERR(qup->pclk)) {
|
||
dev_err(qup->dev, "Could not get iface clock\n");
|
||
return PTR_ERR(qup->pclk);
|
||
}
|
||
qup_i2c_enable_clocks(qup);
|
||
src_clk_freq = clk_get_rate(qup->clk);
|
||
}
|
||
|
||
/*
|
||
* Bootloaders might leave a pending interrupt on certain QUP's,
|
||
* so we reset the core before registering for interrupts.
|
||
*/
|
||
writel(1, qup->base + QUP_SW_RESET);
|
||
ret = qup_i2c_poll_state_valid(qup);
|
||
if (ret)
|
||
goto fail;
|
||
|
||
ret = devm_request_irq(qup->dev, qup->irq, qup_i2c_interrupt,
|
||
IRQF_TRIGGER_HIGH, "i2c_qup", qup);
|
||
if (ret) {
|
||
dev_err(qup->dev, "Request %d IRQ failed\n", qup->irq);
|
||
goto fail;
|
||
}
|
||
disable_irq(qup->irq);
|
||
|
||
hw_ver = readl(qup->base + QUP_HW_VERSION);
|
||
dev_dbg(qup->dev, "Revision %x\n", hw_ver);
|
||
|
||
io_mode = readl(qup->base + QUP_IO_MODE);
|
||
|
||
/*
|
||
* The block/fifo size w.r.t. 'actual data' is 1/2 due to 'tag'
|
||
* associated with each byte written/received
|
||
*/
|
||
size = QUP_OUTPUT_BLOCK_SIZE(io_mode);
|
||
if (size >= ARRAY_SIZE(blk_sizes)) {
|
||
ret = -EIO;
|
||
goto fail;
|
||
}
|
||
qup->out_blk_sz = blk_sizes[size];
|
||
|
||
size = QUP_INPUT_BLOCK_SIZE(io_mode);
|
||
if (size >= ARRAY_SIZE(blk_sizes)) {
|
||
ret = -EIO;
|
||
goto fail;
|
||
}
|
||
qup->in_blk_sz = blk_sizes[size];
|
||
|
||
if (is_qup_v1) {
|
||
/*
|
||
* in QUP v1, QUP_CONFIG uses N as 15 i.e 16 bits constitutes a
|
||
* single transfer but the block size is in bytes so divide the
|
||
* in_blk_sz and out_blk_sz by 2
|
||
*/
|
||
qup->in_blk_sz /= 2;
|
||
qup->out_blk_sz /= 2;
|
||
qup->write_tx_fifo = qup_i2c_write_tx_fifo_v1;
|
||
qup->read_rx_fifo = qup_i2c_read_rx_fifo_v1;
|
||
qup->write_rx_tags = qup_i2c_write_rx_tags_v1;
|
||
} else {
|
||
qup->write_tx_fifo = qup_i2c_write_tx_fifo_v2;
|
||
qup->read_rx_fifo = qup_i2c_read_rx_fifo_v2;
|
||
qup->write_rx_tags = qup_i2c_write_rx_tags_v2;
|
||
}
|
||
|
||
size = QUP_OUTPUT_FIFO_SIZE(io_mode);
|
||
qup->out_fifo_sz = qup->out_blk_sz * (2 << size);
|
||
|
||
size = QUP_INPUT_FIFO_SIZE(io_mode);
|
||
qup->in_fifo_sz = qup->in_blk_sz * (2 << size);
|
||
|
||
hs_div = 3;
|
||
if (clk_freq <= I2C_STANDARD_FREQ) {
|
||
fs_div = ((src_clk_freq / clk_freq) / 2) - 3;
|
||
qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff);
|
||
} else {
|
||
/* 33%/66% duty cycle */
|
||
fs_div = ((src_clk_freq / clk_freq) - 6) * 2 / 3;
|
||
qup->clk_ctl = ((fs_div / 2) << 16) | (hs_div << 8) | (fs_div & 0xff);
|
||
}
|
||
|
||
/*
|
||
* Time it takes for a byte to be clocked out on the bus.
|
||
* Each byte takes 9 clock cycles (8 bits + 1 ack).
|
||
*/
|
||
one_bit_t = (USEC_PER_SEC / clk_freq) + 1;
|
||
qup->one_byte_t = one_bit_t * 9;
|
||
qup->xfer_timeout = TOUT_MIN * HZ +
|
||
usecs_to_jiffies(MX_DMA_TX_RX_LEN * qup->one_byte_t);
|
||
|
||
dev_dbg(qup->dev, "IN:block:%d, fifo:%d, OUT:block:%d, fifo:%d\n",
|
||
qup->in_blk_sz, qup->in_fifo_sz,
|
||
qup->out_blk_sz, qup->out_fifo_sz);
|
||
|
||
i2c_set_adapdata(&qup->adap, qup);
|
||
qup->adap.dev.parent = qup->dev;
|
||
qup->adap.dev.of_node = pdev->dev.of_node;
|
||
qup->is_last = true;
|
||
|
||
strlcpy(qup->adap.name, "QUP I2C adapter", sizeof(qup->adap.name));
|
||
|
||
pm_runtime_set_autosuspend_delay(qup->dev, MSEC_PER_SEC);
|
||
pm_runtime_use_autosuspend(qup->dev);
|
||
pm_runtime_set_active(qup->dev);
|
||
pm_runtime_enable(qup->dev);
|
||
|
||
ret = i2c_add_adapter(&qup->adap);
|
||
if (ret)
|
||
goto fail_runtime;
|
||
|
||
return 0;
|
||
|
||
fail_runtime:
|
||
pm_runtime_disable(qup->dev);
|
||
pm_runtime_set_suspended(qup->dev);
|
||
fail:
|
||
qup_i2c_disable_clocks(qup);
|
||
fail_dma:
|
||
if (qup->btx.dma)
|
||
dma_release_channel(qup->btx.dma);
|
||
if (qup->brx.dma)
|
||
dma_release_channel(qup->brx.dma);
|
||
return ret;
|
||
}
|
||
|
||
static int qup_i2c_remove(struct platform_device *pdev)
|
||
{
|
||
struct qup_i2c_dev *qup = platform_get_drvdata(pdev);
|
||
|
||
if (qup->is_dma) {
|
||
dma_release_channel(qup->btx.dma);
|
||
dma_release_channel(qup->brx.dma);
|
||
}
|
||
|
||
disable_irq(qup->irq);
|
||
qup_i2c_disable_clocks(qup);
|
||
i2c_del_adapter(&qup->adap);
|
||
pm_runtime_disable(qup->dev);
|
||
pm_runtime_set_suspended(qup->dev);
|
||
return 0;
|
||
}
|
||
|
||
#ifdef CONFIG_PM
|
||
static int qup_i2c_pm_suspend_runtime(struct device *device)
|
||
{
|
||
struct qup_i2c_dev *qup = dev_get_drvdata(device);
|
||
|
||
dev_dbg(device, "pm_runtime: suspending...\n");
|
||
qup_i2c_disable_clocks(qup);
|
||
return 0;
|
||
}
|
||
|
||
static int qup_i2c_pm_resume_runtime(struct device *device)
|
||
{
|
||
struct qup_i2c_dev *qup = dev_get_drvdata(device);
|
||
|
||
dev_dbg(device, "pm_runtime: resuming...\n");
|
||
qup_i2c_enable_clocks(qup);
|
||
return 0;
|
||
}
|
||
#endif
|
||
|
||
#ifdef CONFIG_PM_SLEEP
|
||
static int qup_i2c_suspend(struct device *device)
|
||
{
|
||
if (!pm_runtime_suspended(device))
|
||
return qup_i2c_pm_suspend_runtime(device);
|
||
return 0;
|
||
}
|
||
|
||
static int qup_i2c_resume(struct device *device)
|
||
{
|
||
qup_i2c_pm_resume_runtime(device);
|
||
pm_runtime_mark_last_busy(device);
|
||
pm_request_autosuspend(device);
|
||
return 0;
|
||
}
|
||
#endif
|
||
|
||
static const struct dev_pm_ops qup_i2c_qup_pm_ops = {
|
||
SET_SYSTEM_SLEEP_PM_OPS(
|
||
qup_i2c_suspend,
|
||
qup_i2c_resume)
|
||
SET_RUNTIME_PM_OPS(
|
||
qup_i2c_pm_suspend_runtime,
|
||
qup_i2c_pm_resume_runtime,
|
||
NULL)
|
||
};
|
||
|
||
static const struct of_device_id qup_i2c_dt_match[] = {
|
||
{ .compatible = "qcom,i2c-qup-v1.1.1" },
|
||
{ .compatible = "qcom,i2c-qup-v2.1.1" },
|
||
{ .compatible = "qcom,i2c-qup-v2.2.1" },
|
||
{}
|
||
};
|
||
MODULE_DEVICE_TABLE(of, qup_i2c_dt_match);
|
||
|
||
static struct platform_driver qup_i2c_driver = {
|
||
.probe = qup_i2c_probe,
|
||
.remove = qup_i2c_remove,
|
||
.driver = {
|
||
.name = "i2c_qup",
|
||
.pm = &qup_i2c_qup_pm_ops,
|
||
.of_match_table = qup_i2c_dt_match,
|
||
.acpi_match_table = ACPI_PTR(qup_i2c_acpi_match),
|
||
},
|
||
};
|
||
|
||
module_platform_driver(qup_i2c_driver);
|
||
|
||
MODULE_LICENSE("GPL v2");
|
||
MODULE_ALIAS("platform:i2c_qup");
|