WSL2-Linux-Kernel/drivers/ata/pata_ns87410.c

164 строки
4.1 KiB
C

// SPDX-License-Identifier: GPL-2.0-or-later
/*
* pata_ns87410.c - National Semiconductor 87410 PATA for new ATA layer
* (C) 2006 Red Hat Inc
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_ns87410"
#define DRV_VERSION "0.4.6"
/**
* ns87410_pre_reset - probe begin
* @link: ATA link
* @deadline: deadline jiffies for the operation
*
* Check enabled ports
*/
static int ns87410_pre_reset(struct ata_link *link, unsigned long deadline)
{
struct ata_port *ap = link->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const struct pci_bits ns87410_enable_bits[] = {
{ 0x43, 1, 0x08, 0x08 },
{ 0x47, 1, 0x08, 0x08 }
};
if (!pci_test_config_bits(pdev, &ns87410_enable_bits[ap->port_no]))
return -ENOENT;
return ata_sff_prereset(link, deadline);
}
/**
* ns87410_set_piomode - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Program timing data. This is kept per channel not per device,
* and only affects the data port.
*/
static void ns87410_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int port = 0x40 + 4 * ap->port_no;
u8 idetcr, idefr;
struct ata_timing at;
static const u8 activebits[15] = {
0, 1, 2, 3, 4,
5, 5, 6, 6, 6,
6, 7, 7, 7, 7
};
static const u8 recoverbits[12] = {
0, 1, 2, 3, 4, 5, 6, 6, 7, 7, 7, 7
};
pci_read_config_byte(pdev, port + 3, &idefr);
if (ata_pio_need_iordy(adev))
idefr |= 0x04; /* IORDY enable */
else
idefr &= ~0x04;
if (ata_timing_compute(adev, adev->pio_mode, &at, 30303, 1) < 0) {
dev_err(&pdev->dev, "unknown mode %d\n", adev->pio_mode);
return;
}
at.active = clamp_val(at.active, 2, 16) - 2;
at.setup = clamp_val(at.setup, 1, 4) - 1;
at.recover = clamp_val(at.recover, 1, 12) - 1;
idetcr = (at.setup << 6) | (recoverbits[at.recover] << 3) | activebits[at.active];
pci_write_config_byte(pdev, port, idetcr);
pci_write_config_byte(pdev, port + 3, idefr);
/* We use ap->private_data as a pointer to the device currently
loaded for timing */
ap->private_data = adev;
}
/**
* ns87410_qc_issue - command issue
* @qc: command pending
*
* Called when the libata layer is about to issue a command. We wrap
* this interface so that we can load the correct ATA timings if
* necessary.
*/
static unsigned int ns87410_qc_issue(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ata_device *adev = qc->dev;
/* If modes have been configured and the channel data is not loaded
then load it. We have to check if pio_mode is set as the core code
does not set adev->pio_mode to XFER_PIO_0 while probing as would be
logical */
if (adev->pio_mode && adev != ap->private_data)
ns87410_set_piomode(ap, adev);
return ata_sff_qc_issue(qc);
}
static const struct scsi_host_template ns87410_sht = {
ATA_PIO_SHT(DRV_NAME),
};
static struct ata_port_operations ns87410_port_ops = {
.inherits = &ata_sff_port_ops,
.qc_issue = ns87410_qc_issue,
.cable_detect = ata_cable_40wire,
.set_piomode = ns87410_set_piomode,
.prereset = ns87410_pre_reset,
};
static int ns87410_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO3,
.port_ops = &ns87410_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
return ata_pci_sff_init_one(dev, ppi, &ns87410_sht, NULL, 0);
}
static const struct pci_device_id ns87410[] = {
{ PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_87410), },
{ },
};
static struct pci_driver ns87410_pci_driver = {
.name = DRV_NAME,
.id_table = ns87410,
.probe = ns87410_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM_SLEEP
.suspend = ata_pci_device_suspend,
.resume = ata_pci_device_resume,
#endif
};
module_pci_driver(ns87410_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Nat Semi 87410");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, ns87410);
MODULE_VERSION(DRV_VERSION);