WSL2-Linux-Kernel/include/asm-v850/v850e_uartb.h

263 строки
9.7 KiB
C
Исходник Ответственный История

Этот файл содержит невидимые символы Юникода!

Этот файл содержит невидимые символы Юникода, которые могут быть отображены не так, как показано ниже. Если это намеренно, можете спокойно проигнорировать это предупреждение. Используйте кнопку Экранировать, чтобы показать скрытые символы.

/*
* include/asm-v850/v850e_uartb.h -- V850E on-chip `UARTB' UART
*
* Copyright (C) 2001,02,03 NEC Electronics Corporation
* Copyright (C) 2001,02,03 Miles Bader <miles@gnu.org>
*
* This file is subject to the terms and conditions of the GNU General
* Public License. See the file COPYING in the main directory of this
* archive for more details.
*
* Written by Miles Bader <miles@gnu.org>
*/
/* The V850E UARTB is basically a superset of the original V850E UART, but
even where it's the same, the names and details have changed a bit.
It's similar enough to use the same driver (v850e_uart.c), but the
details have been abstracted slightly to do so. */
#ifndef __V850_V850E_UARTB_H__
#define __V850_V850E_UARTB_H__
/* Raw hardware interface. */
#define V850E_UARTB_BASE_ADDR(n) (0xFFFFFA00 + 0x10 * (n))
/* Addresses of specific UART control registers for channel N. */
#define V850E_UARTB_CTL0_ADDR(n) (V850E_UARTB_BASE_ADDR(n) + 0x0)
#define V850E_UARTB_CTL2_ADDR(n) (V850E_UARTB_BASE_ADDR(n) + 0x2)
#define V850E_UARTB_STR_ADDR(n) (V850E_UARTB_BASE_ADDR(n) + 0x4)
#define V850E_UARTB_RX_ADDR(n) (V850E_UARTB_BASE_ADDR(n) + 0x6)
#define V850E_UARTB_RXAP_ADDR(n) (V850E_UARTB_BASE_ADDR(n) + 0x6)
#define V850E_UARTB_TX_ADDR(n) (V850E_UARTB_BASE_ADDR(n) + 0x8)
#define V850E_UARTB_FIC0_ADDR(n) (V850E_UARTB_BASE_ADDR(n) + 0xA)
#define V850E_UARTB_FIC1_ADDR(n) (V850E_UARTB_BASE_ADDR(n) + 0xB)
#define V850E_UARTB_FIC2_ADDR(n) (V850E_UARTB_BASE_ADDR(n) + 0xC)
#define V850E_UARTB_FIS0_ADDR(n) (V850E_UARTB_BASE_ADDR(n) + 0xE)
#define V850E_UARTB_FIS1_ADDR(n) (V850E_UARTB_BASE_ADDR(n) + 0xF)
/* UARTB control register 0 (general config). */
#define V850E_UARTB_CTL0(n) (*(volatile u8 *)V850E_UARTB_CTL0_ADDR(n))
/* Control bits for config registers. */
#define V850E_UARTB_CTL0_PWR 0x80 /* clock enable */
#define V850E_UARTB_CTL0_TXE 0x40 /* transmit enable */
#define V850E_UARTB_CTL0_RXE 0x20 /* receive enable */
#define V850E_UARTB_CTL0_DIR 0x10 /* */
#define V850E_UARTB_CTL0_PS1 0x08 /* parity */
#define V850E_UARTB_CTL0_PS0 0x04 /* parity */
#define V850E_UARTB_CTL0_CL 0x02 /* char len 1:8bit, 0:7bit */
#define V850E_UARTB_CTL0_SL 0x01 /* stop bit 1:2bit, 0:1bit */
#define V850E_UARTB_CTL0_PS_MASK 0x0C /* mask covering parity bits */
#define V850E_UARTB_CTL0_PS_NONE 0x00 /* no parity */
#define V850E_UARTB_CTL0_PS_ZERO 0x04 /* zero parity */
#define V850E_UARTB_CTL0_PS_ODD 0x08 /* odd parity */
#define V850E_UARTB_CTL0_PS_EVEN 0x0C /* even parity */
#define V850E_UARTB_CTL0_CL_8 0x02 /* char len 1:8bit, 0:7bit */
#define V850E_UARTB_CTL0_SL_2 0x01 /* stop bit 1:2bit, 0:1bit */
/* UARTB control register 2 (clock divider). */
#define V850E_UARTB_CTL2(n) (*(volatile u16 *)V850E_UARTB_CTL2_ADDR(n))
#define V850E_UARTB_CTL2_MIN 4
#define V850E_UARTB_CTL2_MAX 0xFFFF
/* UARTB serial interface status register. */
#define V850E_UARTB_STR(n) (*(volatile u8 *)V850E_UARTB_STR_ADDR(n))
/* Control bits for status registers. */
#define V850E_UARTB_STR_TSF 0x80 /* UBTX or FIFO exist data */
#define V850E_UARTB_STR_OVF 0x08 /* overflow error */
#define V850E_UARTB_STR_PE 0x04 /* parity error */
#define V850E_UARTB_STR_FE 0x02 /* framing error */
#define V850E_UARTB_STR_OVE 0x01 /* overrun error */
/* UARTB receive data register. */
#define V850E_UARTB_RX(n) (*(volatile u8 *)V850E_UARTB_RX_ADDR(n))
#define V850E_UARTB_RXAP(n) (*(volatile u16 *)V850E_UARTB_RXAP_ADDR(n))
/* Control bits for status registers. */
#define V850E_UARTB_RXAP_PEF 0x0200 /* parity error */
#define V850E_UARTB_RXAP_FEF 0x0100 /* framing error */
/* UARTB transmit data register. */
#define V850E_UARTB_TX(n) (*(volatile u8 *)V850E_UARTB_TX_ADDR(n))
/* UARTB FIFO control register 0. */
#define V850E_UARTB_FIC0(n) (*(volatile u8 *)V850E_UARTB_FIC0_ADDR(n))
/* UARTB FIFO control register 1. */
#define V850E_UARTB_FIC1(n) (*(volatile u8 *)V850E_UARTB_FIC1_ADDR(n))
/* UARTB FIFO control register 2. */
#define V850E_UARTB_FIC2(n) (*(volatile u16 *)V850E_UARTB_FIC2_ADDR(n))
/* UARTB FIFO status register 0. */
#define V850E_UARTB_FIS0(n) (*(volatile u8 *)V850E_UARTB_FIS0_ADDR(n))
/* UARTB FIFO status register 1. */
#define V850E_UARTB_FIS1(n) (*(volatile u8 *)V850E_UARTB_FIS1_ADDR(n))
/* Slightly abstract interface used by driver. */
/* Interrupts used by the UART. */
/* Received when the most recently transmitted character has been sent. */
#define V850E_UART_TX_IRQ(chan) IRQ_INTUBTIT (chan)
/* Received when a new character has been received. */
#define V850E_UART_RX_IRQ(chan) IRQ_INTUBTIR (chan)
/* Use by serial driver for information purposes. */
#define V850E_UART_BASE_ADDR(chan) V850E_UARTB_BASE_ADDR(chan)
/* UART clock generator interface. */
/* This type encapsulates a particular uart frequency. */
typedef u16 v850e_uart_speed_t;
/* Calculate a uart speed from BAUD for this uart. */
static inline v850e_uart_speed_t v850e_uart_calc_speed (unsigned baud)
{
v850e_uart_speed_t speed;
/*
* V850E/ME2 UARTB baud rate is determined by the value of UBCTL2
* fx = V850E_UARTB_BASE_FREQ = CPU_CLOCK_FREQ/4
* baud = fx / 2*speed [ speed >= 4 ]
*/
speed = V850E_UARTB_CTL2_MIN;
while (((V850E_UARTB_BASE_FREQ / 2) / speed ) > baud)
speed++;
return speed;
}
/* Return the current speed of uart channel CHAN. */
#define v850e_uart_speed(chan) V850E_UARTB_CTL2 (chan)
/* Set the current speed of uart channel CHAN. */
#define v850e_uart_set_speed(chan, speed) (V850E_UARTB_CTL2 (chan) = (speed))
/* Return true if SPEED1 and SPEED2 are the same. */
#define v850e_uart_speed_eq(speed1, speed2) ((speed1) == (speed2))
/* Minimum baud rate possible. */
#define v850e_uart_min_baud() \
((V850E_UARTB_BASE_FREQ / 2) / V850E_UARTB_CTL2_MAX)
/* Maximum baud rate possible. The error is quite high at max, though. */
#define v850e_uart_max_baud() \
((V850E_UARTB_BASE_FREQ / 2) / V850E_UARTB_CTL2_MIN)
/* The `maximum' clock rate the uart can used, which is wanted (though not
really used in any useful way) by the serial framework. */
#define v850e_uart_max_clock() \
(V850E_UARTB_BASE_FREQ / 2)
/* UART configuration interface. */
/* Type of the uart config register; must be a scalar. */
typedef u16 v850e_uart_config_t;
/* The uart hardware config register for channel CHAN. */
#define V850E_UART_CONFIG(chan) V850E_UARTB_CTL0 (chan)
/* This config bit set if the uart is enabled. */
#define V850E_UART_CONFIG_ENABLED V850E_UARTB_CTL0_PWR
/* If the uart _isn't_ enabled, store this value to it to do so. */
#define V850E_UART_CONFIG_INIT V850E_UARTB_CTL0_PWR
/* Store this config value to disable the uart channel completely. */
#define V850E_UART_CONFIG_FINI 0
/* Setting/clearing these bits enable/disable TX/RX, respectively (but
otherwise generally leave things running). */
#define V850E_UART_CONFIG_RX_ENABLE V850E_UARTB_CTL0_RXE
#define V850E_UART_CONFIG_TX_ENABLE V850E_UARTB_CTL0_TXE
/* These masks define which config bits affect TX/RX modes, respectively. */
#define V850E_UART_CONFIG_RX_BITS \
(V850E_UARTB_CTL0_PS_MASK | V850E_UARTB_CTL0_CL_8)
#define V850E_UART_CONFIG_TX_BITS \
(V850E_UARTB_CTL0_PS_MASK | V850E_UARTB_CTL0_CL_8 | V850E_UARTB_CTL0_SL_2)
static inline v850e_uart_config_t v850e_uart_calc_config (unsigned cflags)
{
v850e_uart_config_t config = 0;
/* Figure out new configuration of control register. */
if (cflags & CSTOPB)
/* Number of stop bits, 1 or 2. */
config |= V850E_UARTB_CTL0_SL_2;
if ((cflags & CSIZE) == CS8)
/* Number of data bits, 7 or 8. */
config |= V850E_UARTB_CTL0_CL_8;
if (! (cflags & PARENB))
/* No parity check/generation. */
config |= V850E_UARTB_CTL0_PS_NONE;
else if (cflags & PARODD)
/* Odd parity check/generation. */
config |= V850E_UARTB_CTL0_PS_ODD;
else
/* Even parity check/generation. */
config |= V850E_UARTB_CTL0_PS_EVEN;
if (cflags & CREAD)
/* Reading enabled. */
config |= V850E_UARTB_CTL0_RXE;
config |= V850E_UARTB_CTL0_PWR;
config |= V850E_UARTB_CTL0_TXE; /* Writing is always enabled. */
config |= V850E_UARTB_CTL0_DIR; /* LSB first. */
return config;
}
/* This should delay as long as necessary for a recently written config
setting to settle, before we turn the uart back on. */
static inline void
v850e_uart_config_delay (v850e_uart_config_t config, v850e_uart_speed_t speed)
{
/* The UART may not be reset properly unless we wait at least 2
`basic-clocks' until turning on the TXE/RXE bits again.
A `basic clock' is the clock used by the baud-rate generator,
i.e., the cpu clock divided by the 2^new_clk_divlog2.
The loop takes 2 insns, so loop CYCLES / 2 times. */
register unsigned count = 1 << speed;
while (--count != 0)
/* nothing */;
}
/* RX/TX interface. */
/* Return true if all characters awaiting transmission on uart channel N
have been transmitted. */
#define v850e_uart_xmit_done(n) \
(! (V850E_UARTB_STR(n) & V850E_UARTB_STR_TSF))
/* Wait for this to be true. */
#define v850e_uart_wait_for_xmit_done(n) \
do { } while (! v850e_uart_xmit_done (n))
/* Return true if uart channel N is ready to transmit a character. */
#define v850e_uart_xmit_ok(n) \
(v850e_uart_xmit_done(n) && v850e_uart_cts(n))
/* Wait for this to be true. */
#define v850e_uart_wait_for_xmit_ok(n) \
do { } while (! v850e_uart_xmit_ok (n))
/* Write character CH to uart channel CHAN. */
#define v850e_uart_putc(chan, ch) (V850E_UARTB_TX(chan) = (ch))
/* Return latest character read on channel CHAN. */
#define v850e_uart_getc(chan) V850E_UARTB_RX (chan)
/* Return bit-mask of uart error status. */
#define v850e_uart_err(chan) V850E_UARTB_STR (chan)
/* Various error bits set in the error result. */
#define V850E_UART_ERR_OVERRUN V850E_UARTB_STR_OVE
#define V850E_UART_ERR_FRAME V850E_UARTB_STR_FE
#define V850E_UART_ERR_PARITY V850E_UARTB_STR_PE
#endif /* __V850_V850E_UARTB_H__ */