888 строки
35 KiB
ReStructuredText
888 строки
35 KiB
ReStructuredText
=============================
|
|
More Notes on HD-Audio Driver
|
|
=============================
|
|
|
|
Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
General
|
|
=======
|
|
|
|
HD-audio is the new standard on-board audio component on modern PCs
|
|
after AC97. Although Linux has been supporting HD-audio since long
|
|
time ago, there are often problems with new machines. A part of the
|
|
problem is broken BIOS, and the rest is the driver implementation.
|
|
This document explains the brief trouble-shooting and debugging
|
|
methods for the HD-audio hardware.
|
|
|
|
The HD-audio component consists of two parts: the controller chip and
|
|
the codec chips on the HD-audio bus. Linux provides a single driver
|
|
for all controllers, snd-hda-intel. Although the driver name contains
|
|
a word of a well-known hardware vendor, it's not specific to it but for
|
|
all controller chips by other companies. Since the HD-audio
|
|
controllers are supposed to be compatible, the single snd-hda-driver
|
|
should work in most cases. But, not surprisingly, there are known
|
|
bugs and issues specific to each controller type. The snd-hda-intel
|
|
driver has a bunch of workarounds for these as described below.
|
|
|
|
A controller may have multiple codecs. Usually you have one audio
|
|
codec and optionally one modem codec. In theory, there might be
|
|
multiple audio codecs, e.g. for analog and digital outputs, and the
|
|
driver might not work properly because of conflict of mixer elements.
|
|
This should be fixed in future if such hardware really exists.
|
|
|
|
The snd-hda-intel driver has several different codec parsers depending
|
|
on the codec. It has a generic parser as a fallback, but this
|
|
functionality is fairly limited until now. Instead of the generic
|
|
parser, usually the codec-specific parser (coded in patch_*.c) is used
|
|
for the codec-specific implementations. The details about the
|
|
codec-specific problems are explained in the later sections.
|
|
|
|
If you are interested in the deep debugging of HD-audio, read the
|
|
HD-audio specification at first. The specification is found on
|
|
Intel's web page, for example:
|
|
|
|
* https://www.intel.com/standards/hdaudio/
|
|
|
|
|
|
HD-Audio Controller
|
|
===================
|
|
|
|
DMA-Position Problem
|
|
--------------------
|
|
The most common problem of the controller is the inaccurate DMA
|
|
pointer reporting. The DMA pointer for playback and capture can be
|
|
read in two ways, either via a LPIB register or via a position-buffer
|
|
map. As default the driver tries to read from the io-mapped
|
|
position-buffer, and falls back to LPIB if the position-buffer appears
|
|
dead. However, this detection isn't perfect on some devices. In such
|
|
a case, you can change the default method via ``position_fix`` option.
|
|
|
|
``position_fix=1`` means to use LPIB method explicitly.
|
|
``position_fix=2`` means to use the position-buffer.
|
|
``position_fix=3`` means to use a combination of both methods, needed
|
|
for some VIA controllers. The capture stream position is corrected
|
|
by comparing both LPIB and position-buffer values.
|
|
``position_fix=4`` is another combination available for all controllers,
|
|
and uses LPIB for the playback and the position-buffer for the capture
|
|
streams.
|
|
``position_fix=5`` is specific to Intel platforms, so far, for Skylake
|
|
and onward. It applies the delay calculation for the precise position
|
|
reporting.
|
|
``position_fix=6`` is to correct the position with the fixed FIFO
|
|
size, mainly targeted for the recent AMD controllers.
|
|
0 is the default value for all other
|
|
controllers, the automatic check and fallback to LPIB as described in
|
|
the above. If you get a problem of repeated sounds, this option might
|
|
help.
|
|
|
|
In addition to that, every controller is known to be broken regarding
|
|
the wake-up timing. It wakes up a few samples before actually
|
|
processing the data on the buffer. This caused a lot of problems, for
|
|
example, with ALSA dmix or JACK. Since 2.6.27 kernel, the driver puts
|
|
an artificial delay to the wake up timing. This delay is controlled
|
|
via ``bdl_pos_adj`` option.
|
|
|
|
When ``bdl_pos_adj`` is a negative value (as default), it's assigned to
|
|
an appropriate value depending on the controller chip. For Intel
|
|
chips, it'd be 1 while it'd be 32 for others. Usually this works.
|
|
Only in case it doesn't work and you get warning messages, you should
|
|
change this parameter to other values.
|
|
|
|
|
|
Codec-Probing Problem
|
|
---------------------
|
|
A less often but a more severe problem is the codec probing. When
|
|
BIOS reports the available codec slots wrongly, the driver gets
|
|
confused and tries to access the non-existing codec slot. This often
|
|
results in the total screw-up, and destructs the further communication
|
|
with the codec chips. The symptom appears usually as error messages
|
|
like:
|
|
::
|
|
|
|
hda_intel: azx_get_response timeout, switching to polling mode:
|
|
last cmd=0x12345678
|
|
hda_intel: azx_get_response timeout, switching to single_cmd mode:
|
|
last cmd=0x12345678
|
|
|
|
The first line is a warning, and this is usually relatively harmless.
|
|
It means that the codec response isn't notified via an IRQ. The
|
|
driver uses explicit polling method to read the response. It gives
|
|
very slight CPU overhead, but you'd unlikely notice it.
|
|
|
|
The second line is, however, a fatal error. If this happens, usually
|
|
it means that something is really wrong. Most likely you are
|
|
accessing a non-existing codec slot.
|
|
|
|
Thus, if the second error message appears, try to narrow the probed
|
|
codec slots via ``probe_mask`` option. It's a bitmask, and each bit
|
|
corresponds to the codec slot. For example, to probe only the first
|
|
slot, pass ``probe_mask=1``. For the first and the third slots, pass
|
|
``probe_mask=5`` (where 5 = 1 | 4), and so on.
|
|
|
|
Since 2.6.29 kernel, the driver has a more robust probing method, so
|
|
this error might happen rarely, though.
|
|
|
|
On a machine with a broken BIOS, sometimes you need to force the
|
|
driver to probe the codec slots the hardware doesn't report for use.
|
|
In such a case, turn the bit 8 (0x100) of ``probe_mask`` option on.
|
|
Then the rest 8 bits are passed as the codec slots to probe
|
|
unconditionally. For example, ``probe_mask=0x103`` will force to probe
|
|
the codec slots 0 and 1 no matter what the hardware reports.
|
|
|
|
|
|
Interrupt Handling
|
|
------------------
|
|
HD-audio driver uses MSI as default (if available) since 2.6.33
|
|
kernel as MSI works better on some machines, and in general, it's
|
|
better for performance. However, Nvidia controllers showed bad
|
|
regressions with MSI (especially in a combination with AMD chipset),
|
|
thus we disabled MSI for them.
|
|
|
|
There seem also still other devices that don't work with MSI. If you
|
|
see a regression wrt the sound quality (stuttering, etc) or a lock-up
|
|
in the recent kernel, try to pass ``enable_msi=0`` option to disable
|
|
MSI. If it works, you can add the known bad device to the blacklist
|
|
defined in hda_intel.c. In such a case, please report and give the
|
|
patch back to the upstream developer.
|
|
|
|
|
|
HD-Audio Codec
|
|
==============
|
|
|
|
Model Option
|
|
------------
|
|
The most common problem regarding the HD-audio driver is the
|
|
unsupported codec features or the mismatched device configuration.
|
|
Most of codec-specific code has several preset models, either to
|
|
override the BIOS setup or to provide more comprehensive features.
|
|
|
|
The driver checks PCI SSID and looks through the static configuration
|
|
table until any matching entry is found. If you have a new machine,
|
|
you may see a message like below:
|
|
::
|
|
|
|
hda_codec: ALC880: BIOS auto-probing.
|
|
|
|
Meanwhile, in the earlier versions, you would see a message like:
|
|
::
|
|
|
|
hda_codec: Unknown model for ALC880, trying auto-probe from BIOS...
|
|
|
|
Even if you see such a message, DON'T PANIC. Take a deep breath and
|
|
keep your towel. First of all, it's an informational message, no
|
|
warning, no error. This means that the PCI SSID of your device isn't
|
|
listed in the known preset model (white-)list. But, this doesn't mean
|
|
that the driver is broken. Many codec-drivers provide the automatic
|
|
configuration mechanism based on the BIOS setup.
|
|
|
|
The HD-audio codec has usually "pin" widgets, and BIOS sets the default
|
|
configuration of each pin, which indicates the location, the
|
|
connection type, the jack color, etc. The HD-audio driver can guess
|
|
the right connection judging from these default configuration values.
|
|
However -- some codec-support codes, such as patch_analog.c, don't
|
|
support the automatic probing (yet as of 2.6.28). And, BIOS is often,
|
|
yes, pretty often broken. It sets up wrong values and screws up the
|
|
driver.
|
|
|
|
The preset model (or recently called as "fix-up") is provided
|
|
basically to overcome such a situation. When the matching preset
|
|
model is found in the white-list, the driver assumes the static
|
|
configuration of that preset with the correct pin setup, etc.
|
|
Thus, if you have a newer machine with a slightly different PCI SSID
|
|
(or codec SSID) from the existing one, you may have a good chance to
|
|
re-use the same model. You can pass the ``model`` option to specify the
|
|
preset model instead of PCI (and codec-) SSID look-up.
|
|
|
|
What ``model`` option values are available depends on the codec chip.
|
|
Check your codec chip from the codec proc file (see "Codec Proc-File"
|
|
section below). It will show the vendor/product name of your codec
|
|
chip. Then, see Documentation/sound/hd-audio/models.rst file,
|
|
the section of HD-audio driver. You can find a list of codecs
|
|
and ``model`` options belonging to each codec. For example, for Realtek
|
|
ALC262 codec chip, pass ``model=ultra`` for devices that are compatible
|
|
with Samsung Q1 Ultra.
|
|
|
|
Thus, the first thing you can do for any brand-new, unsupported and
|
|
non-working HD-audio hardware is to check HD-audio codec and several
|
|
different ``model`` option values. If you have any luck, some of them
|
|
might suit with your device well.
|
|
|
|
There are a few special model option values:
|
|
|
|
* when 'nofixup' is passed, the device-specific fixups in the codec
|
|
parser are skipped.
|
|
* when ``generic`` is passed, the codec-specific parser is skipped and
|
|
only the generic parser is used.
|
|
|
|
|
|
Speaker and Headphone Output
|
|
----------------------------
|
|
One of the most frequent (and obvious) bugs with HD-audio is the
|
|
silent output from either or both of a built-in speaker and a
|
|
headphone jack. In general, you should try a headphone output at
|
|
first. A speaker output often requires more additional controls like
|
|
the external amplifier bits. Thus a headphone output has a slightly
|
|
better chance.
|
|
|
|
Before making a bug report, double-check whether the mixer is set up
|
|
correctly. The recent version of snd-hda-intel driver provides mostly
|
|
"Master" volume control as well as "Front" volume (where Front
|
|
indicates the front-channels). In addition, there can be individual
|
|
"Headphone" and "Speaker" controls.
|
|
|
|
Ditto for the speaker output. There can be "External Amplifier"
|
|
switch on some codecs. Turn on this if present.
|
|
|
|
Another related problem is the automatic mute of speaker output by
|
|
headphone plugging. This feature is implemented in most cases, but
|
|
not on every preset model or codec-support code.
|
|
|
|
In anyway, try a different model option if you have such a problem.
|
|
Some other models may match better and give you more matching
|
|
functionality. If none of the available models works, send a bug
|
|
report. See the bug report section for details.
|
|
|
|
If you are masochistic enough to debug the driver problem, note the
|
|
following:
|
|
|
|
* The speaker (and the headphone, too) output often requires the
|
|
external amplifier. This can be set usually via EAPD verb or a
|
|
certain GPIO. If the codec pin supports EAPD, you have a better
|
|
chance via SET_EAPD_BTL verb (0x70c). On others, GPIO pin (mostly
|
|
it's either GPIO0 or GPIO1) may turn on/off EAPD.
|
|
* Some Realtek codecs require special vendor-specific coefficients to
|
|
turn on the amplifier. See patch_realtek.c.
|
|
* IDT codecs may have extra power-enable/disable controls on each
|
|
analog pin. See patch_sigmatel.c.
|
|
* Very rare but some devices don't accept the pin-detection verb until
|
|
triggered. Issuing GET_PIN_SENSE verb (0xf09) may result in the
|
|
codec-communication stall. Some examples are found in
|
|
patch_realtek.c.
|
|
|
|
|
|
Capture Problems
|
|
----------------
|
|
The capture problems are often because of missing setups of mixers.
|
|
Thus, before submitting a bug report, make sure that you set up the
|
|
mixer correctly. For example, both "Capture Volume" and "Capture
|
|
Switch" have to be set properly in addition to the right "Capture
|
|
Source" or "Input Source" selection. Some devices have "Mic Boost"
|
|
volume or switch.
|
|
|
|
When the PCM device is opened via "default" PCM (without pulse-audio
|
|
plugin), you'll likely have "Digital Capture Volume" control as well.
|
|
This is provided for the extra gain/attenuation of the signal in
|
|
software, especially for the inputs without the hardware volume
|
|
control such as digital microphones. Unless really needed, this
|
|
should be set to exactly 50%, corresponding to 0dB -- neither extra
|
|
gain nor attenuation. When you use "hw" PCM, i.e., a raw access PCM,
|
|
this control will have no influence, though.
|
|
|
|
It's known that some codecs / devices have fairly bad analog circuits,
|
|
and the recorded sound contains a certain DC-offset. This is no bug
|
|
of the driver.
|
|
|
|
Most of modern laptops have no analog CD-input connection. Thus, the
|
|
recording from CD input won't work in many cases although the driver
|
|
provides it as the capture source. Use CDDA instead.
|
|
|
|
The automatic switching of the built-in and external mic per plugging
|
|
is implemented on some codec models but not on every model. Partly
|
|
because of my laziness but mostly lack of testers. Feel free to
|
|
submit the improvement patch to the author.
|
|
|
|
|
|
Direct Debugging
|
|
----------------
|
|
If no model option gives you a better result, and you are a tough guy
|
|
to fight against evil, try debugging via hitting the raw HD-audio
|
|
codec verbs to the device. Some tools are available: hda-emu and
|
|
hda-analyzer. The detailed description is found in the sections
|
|
below. You'd need to enable hwdep for using these tools. See "Kernel
|
|
Configuration" section.
|
|
|
|
|
|
Other Issues
|
|
============
|
|
|
|
Kernel Configuration
|
|
--------------------
|
|
In general, I recommend you to enable the sound debug option,
|
|
``CONFIG_SND_DEBUG=y``, no matter whether you are debugging or not.
|
|
This enables snd_printd() macro and others, and you'll get additional
|
|
kernel messages at probing.
|
|
|
|
In addition, you can enable ``CONFIG_SND_DEBUG_VERBOSE=y``. But this
|
|
will give you far more messages. Thus turn this on only when you are
|
|
sure to want it.
|
|
|
|
Don't forget to turn on the appropriate ``CONFIG_SND_HDA_CODEC_*``
|
|
options. Note that each of them corresponds to the codec chip, not
|
|
the controller chip. Thus, even if lspci shows the Nvidia controller,
|
|
you may need to choose the option for other vendors. If you are
|
|
unsure, just select all yes.
|
|
|
|
``CONFIG_SND_HDA_HWDEP`` is a useful option for debugging the driver.
|
|
When this is enabled, the driver creates hardware-dependent devices
|
|
(one per each codec), and you have a raw access to the device via
|
|
these device files. For example, ``hwC0D2`` will be created for the
|
|
codec slot #2 of the first card (#0). For debug-tools such as
|
|
hda-verb and hda-analyzer, the hwdep device has to be enabled.
|
|
Thus, it'd be better to turn this on always.
|
|
|
|
``CONFIG_SND_HDA_RECONFIG`` is a new option, and this depends on the
|
|
hwdep option above. When enabled, you'll have some sysfs files under
|
|
the corresponding hwdep directory. See "HD-audio reconfiguration"
|
|
section below.
|
|
|
|
``CONFIG_SND_HDA_POWER_SAVE`` option enables the power-saving feature.
|
|
See "Power-saving" section below.
|
|
|
|
|
|
Codec Proc-File
|
|
---------------
|
|
The codec proc-file is a treasure-chest for debugging HD-audio.
|
|
It shows most of useful information of each codec widget.
|
|
|
|
The proc file is located in /proc/asound/card*/codec#*, one file per
|
|
each codec slot. You can know the codec vendor, product id and
|
|
names, the type of each widget, capabilities and so on.
|
|
This file, however, doesn't show the jack sensing state, so far. This
|
|
is because the jack-sensing might be depending on the trigger state.
|
|
|
|
This file will be picked up by the debug tools, and also it can be fed
|
|
to the emulator as the primary codec information. See the debug tools
|
|
section below.
|
|
|
|
This proc file can be also used to check whether the generic parser is
|
|
used. When the generic parser is used, the vendor/product ID name
|
|
will appear as "Realtek ID 0262", instead of "Realtek ALC262".
|
|
|
|
|
|
HD-Audio Reconfiguration
|
|
------------------------
|
|
This is an experimental feature to allow you re-configure the HD-audio
|
|
codec dynamically without reloading the driver. The following sysfs
|
|
files are available under each codec-hwdep device directory (e.g.
|
|
/sys/class/sound/hwC0D0):
|
|
|
|
vendor_id
|
|
Shows the 32bit codec vendor-id hex number. You can change the
|
|
vendor-id value by writing to this file.
|
|
subsystem_id
|
|
Shows the 32bit codec subsystem-id hex number. You can change the
|
|
subsystem-id value by writing to this file.
|
|
revision_id
|
|
Shows the 32bit codec revision-id hex number. You can change the
|
|
revision-id value by writing to this file.
|
|
afg
|
|
Shows the AFG ID. This is read-only.
|
|
mfg
|
|
Shows the MFG ID. This is read-only.
|
|
name
|
|
Shows the codec name string. Can be changed by writing to this
|
|
file.
|
|
modelname
|
|
Shows the currently set ``model`` option. Can be changed by writing
|
|
to this file.
|
|
init_verbs
|
|
The extra verbs to execute at initialization. You can add a verb by
|
|
writing to this file. Pass three numbers: nid, verb and parameter
|
|
(separated with a space).
|
|
hints
|
|
Shows / stores hint strings for codec parsers for any use.
|
|
Its format is ``key = value``. For example, passing ``jack_detect = no``
|
|
will disable the jack detection of the machine completely.
|
|
init_pin_configs
|
|
Shows the initial pin default config values set by BIOS.
|
|
driver_pin_configs
|
|
Shows the pin default values set by the codec parser explicitly.
|
|
This doesn't show all pin values but only the changed values by
|
|
the parser. That is, if the parser doesn't change the pin default
|
|
config values by itself, this will contain nothing.
|
|
user_pin_configs
|
|
Shows the pin default config values to override the BIOS setup.
|
|
Writing this (with two numbers, NID and value) appends the new
|
|
value. The given will be used instead of the initial BIOS value at
|
|
the next reconfiguration time. Note that this config will override
|
|
even the driver pin configs, too.
|
|
reconfig
|
|
Triggers the codec re-configuration. When any value is written to
|
|
this file, the driver re-initialize and parses the codec tree
|
|
again. All the changes done by the sysfs entries above are taken
|
|
into account.
|
|
clear
|
|
Resets the codec, removes the mixer elements and PCM stuff of the
|
|
specified codec, and clear all init verbs and hints.
|
|
|
|
For example, when you want to change the pin default configuration
|
|
value of the pin widget 0x14 to 0x9993013f, and let the driver
|
|
re-configure based on that state, run like below:
|
|
::
|
|
|
|
# echo 0x14 0x9993013f > /sys/class/sound/hwC0D0/user_pin_configs
|
|
# echo 1 > /sys/class/sound/hwC0D0/reconfig
|
|
|
|
|
|
Hint Strings
|
|
------------
|
|
The codec parser have several switches and adjustment knobs for
|
|
matching better with the actual codec or device behavior. Many of
|
|
them can be adjusted dynamically via "hints" strings as mentioned in
|
|
the section above. For example, by passing ``jack_detect = no`` string
|
|
via sysfs or a patch file, you can disable the jack detection, thus
|
|
the codec parser will skip the features like auto-mute or mic
|
|
auto-switch. As a boolean value, either ``yes``, ``no``, ``true``, ``false``,
|
|
``1`` or ``0`` can be passed.
|
|
|
|
The generic parser supports the following hints:
|
|
|
|
jack_detect (bool)
|
|
specify whether the jack detection is available at all on this
|
|
machine; default true
|
|
inv_jack_detect (bool)
|
|
indicates that the jack detection logic is inverted
|
|
trigger_sense (bool)
|
|
indicates that the jack detection needs the explicit call of
|
|
AC_VERB_SET_PIN_SENSE verb
|
|
inv_eapd (bool)
|
|
indicates that the EAPD is implemented in the inverted logic
|
|
pcm_format_first (bool)
|
|
sets the PCM format before the stream tag and channel ID
|
|
sticky_stream (bool)
|
|
keep the PCM format, stream tag and ID as long as possible;
|
|
default true
|
|
spdif_status_reset (bool)
|
|
reset the SPDIF status bits at each time the SPDIF stream is set
|
|
up
|
|
pin_amp_workaround (bool)
|
|
the output pin may have multiple amp values
|
|
single_adc_amp (bool)
|
|
ADCs can have only single input amps
|
|
auto_mute (bool)
|
|
enable/disable the headphone auto-mute feature; default true
|
|
auto_mic (bool)
|
|
enable/disable the mic auto-switch feature; default true
|
|
line_in_auto_switch (bool)
|
|
enable/disable the line-in auto-switch feature; default false
|
|
need_dac_fix (bool)
|
|
limits the DACs depending on the channel count
|
|
primary_hp (bool)
|
|
probe headphone jacks as the primary outputs; default true
|
|
multi_io (bool)
|
|
try probing multi-I/O config (e.g. shared line-in/surround,
|
|
mic/clfe jacks)
|
|
multi_cap_vol (bool)
|
|
provide multiple capture volumes
|
|
inv_dmic_split (bool)
|
|
provide split internal mic volume/switch for phase-inverted
|
|
digital mics
|
|
indep_hp (bool)
|
|
provide the independent headphone PCM stream and the corresponding
|
|
mixer control, if available
|
|
add_stereo_mix_input (bool)
|
|
add the stereo mix (analog-loopback mix) to the input mux if
|
|
available
|
|
add_jack_modes (bool)
|
|
add "xxx Jack Mode" enum controls to each I/O jack for allowing to
|
|
change the headphone amp and mic bias VREF capabilities
|
|
power_save_node (bool)
|
|
advanced power management for each widget, controlling the power
|
|
sate (D0/D3) of each widget node depending on the actual pin and
|
|
stream states
|
|
power_down_unused (bool)
|
|
power down the unused widgets, a subset of power_save_node, and
|
|
will be dropped in future
|
|
add_hp_mic (bool)
|
|
add the headphone to capture source if possible
|
|
hp_mic_detect (bool)
|
|
enable/disable the hp/mic shared input for a single built-in mic
|
|
case; default true
|
|
vmaster (bool)
|
|
enable/disable the virtual Master control; default true
|
|
mixer_nid (int)
|
|
specifies the widget NID of the analog-loopback mixer
|
|
|
|
|
|
Early Patching
|
|
--------------
|
|
When ``CONFIG_SND_HDA_PATCH_LOADER=y`` is set, you can pass a "patch"
|
|
as a firmware file for modifying the HD-audio setup before
|
|
initializing the codec. This can work basically like the
|
|
reconfiguration via sysfs in the above, but it does it before the
|
|
first codec configuration.
|
|
|
|
A patch file is a plain text file which looks like below:
|
|
|
|
::
|
|
|
|
[codec]
|
|
0x12345678 0xabcd1234 2
|
|
|
|
[model]
|
|
auto
|
|
|
|
[pincfg]
|
|
0x12 0x411111f0
|
|
|
|
[verb]
|
|
0x20 0x500 0x03
|
|
0x20 0x400 0xff
|
|
|
|
[hint]
|
|
jack_detect = no
|
|
|
|
|
|
The file needs to have a line ``[codec]``. The next line should contain
|
|
three numbers indicating the codec vendor-id (0x12345678 in the
|
|
example), the codec subsystem-id (0xabcd1234) and the address (2) of
|
|
the codec. The rest patch entries are applied to this specified codec
|
|
until another codec entry is given. Passing 0 or a negative number to
|
|
the first or the second value will make the check of the corresponding
|
|
field be skipped. It'll be useful for really broken devices that don't
|
|
initialize SSID properly.
|
|
|
|
The ``[model]`` line allows to change the model name of the each codec.
|
|
In the example above, it will be changed to model=auto.
|
|
Note that this overrides the module option.
|
|
|
|
After the ``[pincfg]`` line, the contents are parsed as the initial
|
|
default pin-configurations just like ``user_pin_configs`` sysfs above.
|
|
The values can be shown in user_pin_configs sysfs file, too.
|
|
|
|
Similarly, the lines after ``[verb]`` are parsed as ``init_verbs``
|
|
sysfs entries, and the lines after ``[hint]`` are parsed as ``hints``
|
|
sysfs entries, respectively.
|
|
|
|
Another example to override the codec vendor id from 0x12345678 to
|
|
0xdeadbeef is like below:
|
|
::
|
|
|
|
[codec]
|
|
0x12345678 0xabcd1234 2
|
|
|
|
[vendor_id]
|
|
0xdeadbeef
|
|
|
|
|
|
In the similar way, you can override the codec subsystem_id via
|
|
``[subsystem_id]``, the revision id via ``[revision_id]`` line.
|
|
Also, the codec chip name can be rewritten via ``[chip_name]`` line.
|
|
::
|
|
|
|
[codec]
|
|
0x12345678 0xabcd1234 2
|
|
|
|
[subsystem_id]
|
|
0xffff1111
|
|
|
|
[revision_id]
|
|
0x10
|
|
|
|
[chip_name]
|
|
My-own NEWS-0002
|
|
|
|
|
|
The hd-audio driver reads the file via request_firmware(). Thus,
|
|
a patch file has to be located on the appropriate firmware path,
|
|
typically, /lib/firmware. For example, when you pass the option
|
|
``patch=hda-init.fw``, the file /lib/firmware/hda-init.fw must be
|
|
present.
|
|
|
|
The patch module option is specific to each card instance, and you
|
|
need to give one file name for each instance, separated by commas.
|
|
For example, if you have two cards, one for an on-board analog and one
|
|
for an HDMI video board, you may pass patch option like below:
|
|
::
|
|
|
|
options snd-hda-intel patch=on-board-patch,hdmi-patch
|
|
|
|
|
|
Power-Saving
|
|
------------
|
|
The power-saving is a kind of auto-suspend of the device. When the
|
|
device is inactive for a certain time, the device is automatically
|
|
turned off to save the power. The time to go down is specified via
|
|
``power_save`` module option, and this option can be changed dynamically
|
|
via sysfs.
|
|
|
|
The power-saving won't work when the analog loopback is enabled on
|
|
some codecs. Make sure that you mute all unneeded signal routes when
|
|
you want the power-saving.
|
|
|
|
The power-saving feature might cause audible click noises at each
|
|
power-down/up depending on the device. Some of them might be
|
|
solvable, but some are hard, I'm afraid. Some distros such as
|
|
openSUSE enables the power-saving feature automatically when the power
|
|
cable is unplugged. Thus, if you hear noises, suspect first the
|
|
power-saving. See /sys/module/snd_hda_intel/parameters/power_save to
|
|
check the current value. If it's non-zero, the feature is turned on.
|
|
|
|
The recent kernel supports the runtime PM for the HD-audio controller
|
|
chip, too. It means that the HD-audio controller is also powered up /
|
|
down dynamically. The feature is enabled only for certain controller
|
|
chips like Intel LynxPoint. You can enable/disable this feature
|
|
forcibly by setting ``power_save_controller`` option, which is also
|
|
available at /sys/module/snd_hda_intel/parameters directory.
|
|
|
|
|
|
Tracepoints
|
|
-----------
|
|
The hd-audio driver gives a few basic tracepoints.
|
|
``hda:hda_send_cmd`` traces each CORB write while ``hda:hda_get_response``
|
|
traces the response from RIRB (only when read from the codec driver).
|
|
``hda:hda_bus_reset`` traces the bus-reset due to fatal error, etc,
|
|
``hda:hda_unsol_event`` traces the unsolicited events, and
|
|
``hda:hda_power_down`` and ``hda:hda_power_up`` trace the power down/up
|
|
via power-saving behavior.
|
|
|
|
Enabling all tracepoints can be done like
|
|
::
|
|
|
|
# echo 1 > /sys/kernel/debug/tracing/events/hda/enable
|
|
|
|
then after some commands, you can traces from
|
|
/sys/kernel/debug/tracing/trace file. For example, when you want to
|
|
trace what codec command is sent, enable the tracepoint like:
|
|
::
|
|
|
|
# cat /sys/kernel/debug/tracing/trace
|
|
# tracer: nop
|
|
#
|
|
# TASK-PID CPU# TIMESTAMP FUNCTION
|
|
# | | | | |
|
|
<...>-7807 [002] 105147.774889: hda_send_cmd: [0:0] val=e3a019
|
|
<...>-7807 [002] 105147.774893: hda_send_cmd: [0:0] val=e39019
|
|
<...>-7807 [002] 105147.999542: hda_send_cmd: [0:0] val=e3a01a
|
|
<...>-7807 [002] 105147.999543: hda_send_cmd: [0:0] val=e3901a
|
|
<...>-26764 [001] 349222.837143: hda_send_cmd: [0:0] val=e3a019
|
|
<...>-26764 [001] 349222.837148: hda_send_cmd: [0:0] val=e39019
|
|
<...>-26764 [001] 349223.058539: hda_send_cmd: [0:0] val=e3a01a
|
|
<...>-26764 [001] 349223.058541: hda_send_cmd: [0:0] val=e3901a
|
|
|
|
Here ``[0:0]`` indicates the card number and the codec address, and
|
|
``val`` shows the value sent to the codec, respectively. The value is
|
|
a packed value, and you can decode it via hda-decode-verb program
|
|
included in hda-emu package below. For example, the value e3a019 is
|
|
to set the left output-amp value to 25.
|
|
::
|
|
|
|
% hda-decode-verb 0xe3a019
|
|
raw value = 0x00e3a019
|
|
cid = 0, nid = 0x0e, verb = 0x3a0, parm = 0x19
|
|
raw value: verb = 0x3a0, parm = 0x19
|
|
verbname = set_amp_gain_mute
|
|
amp raw val = 0xa019
|
|
output, left, idx=0, mute=0, val=25
|
|
|
|
|
|
Development Tree
|
|
----------------
|
|
The latest development codes for HD-audio are found on sound git tree:
|
|
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git
|
|
|
|
The master branch or for-next branches can be used as the main
|
|
development branches in general while the development for the current
|
|
and next kernels are found in for-linus and for-next branches,
|
|
respectively.
|
|
|
|
|
|
Sending a Bug Report
|
|
--------------------
|
|
If any model or module options don't work for your device, it's time
|
|
to send a bug report to the developers. Give the following in your
|
|
bug report:
|
|
|
|
* Hardware vendor, product and model names
|
|
* Kernel version (and ALSA-driver version if you built externally)
|
|
* ``alsa-info.sh`` output; run with ``--no-upload`` option. See the
|
|
section below about alsa-info
|
|
|
|
If it's a regression, at best, send alsa-info outputs of both working
|
|
and non-working kernels. This is really helpful because we can
|
|
compare the codec registers directly.
|
|
|
|
Send a bug report either the following:
|
|
|
|
kernel-bugzilla
|
|
https://bugzilla.kernel.org/
|
|
alsa-devel ML
|
|
alsa-devel@alsa-project.org
|
|
|
|
|
|
Debug Tools
|
|
===========
|
|
|
|
This section describes some tools available for debugging HD-audio
|
|
problems.
|
|
|
|
alsa-info
|
|
---------
|
|
The script ``alsa-info.sh`` is a very useful tool to gather the audio
|
|
device information. It's included in alsa-utils package. The latest
|
|
version can be found on git repository:
|
|
|
|
* git://git.alsa-project.org/alsa-utils.git
|
|
|
|
The script can be fetched directly from the following URL, too:
|
|
|
|
* https://www.alsa-project.org/alsa-info.sh
|
|
|
|
Run this script as root, and it will gather the important information
|
|
such as the module lists, module parameters, proc file contents
|
|
including the codec proc files, mixer outputs and the control
|
|
elements. As default, it will store the information onto a web server
|
|
on alsa-project.org. But, if you send a bug report, it'd be better to
|
|
run with ``--no-upload`` option, and attach the generated file.
|
|
|
|
There are some other useful options. See ``--help`` option output for
|
|
details.
|
|
|
|
When a probe error occurs or when the driver obviously assigns a
|
|
mismatched model, it'd be helpful to load the driver with
|
|
``probe_only=1`` option (at best after the cold reboot) and run
|
|
alsa-info at this state. With this option, the driver won't configure
|
|
the mixer and PCM but just tries to probe the codec slot. After
|
|
probing, the proc file is available, so you can get the raw codec
|
|
information before modified by the driver. Of course, the driver
|
|
isn't usable with ``probe_only=1``. But you can continue the
|
|
configuration via hwdep sysfs file if hda-reconfig option is enabled.
|
|
Using ``probe_only`` mask 2 skips the reset of HDA codecs (use
|
|
``probe_only=3`` as module option). The hwdep interface can be used
|
|
to determine the BIOS codec initialization.
|
|
|
|
|
|
hda-verb
|
|
--------
|
|
hda-verb is a tiny program that allows you to access the HD-audio
|
|
codec directly. You can execute a raw HD-audio codec verb with this.
|
|
This program accesses the hwdep device, thus you need to enable the
|
|
kernel config ``CONFIG_SND_HDA_HWDEP=y`` beforehand.
|
|
|
|
The hda-verb program takes four arguments: the hwdep device file, the
|
|
widget NID, the verb and the parameter. When you access to the codec
|
|
on the slot 2 of the card 0, pass /dev/snd/hwC0D2 to the first
|
|
argument, typically. (However, the real path name depends on the
|
|
system.)
|
|
|
|
The second parameter is the widget number-id to access. The third
|
|
parameter can be either a hex/digit number or a string corresponding
|
|
to a verb. Similarly, the last parameter is the value to write, or
|
|
can be a string for the parameter type.
|
|
|
|
::
|
|
|
|
% hda-verb /dev/snd/hwC0D0 0x12 0x701 2
|
|
nid = 0x12, verb = 0x701, param = 0x2
|
|
value = 0x0
|
|
|
|
% hda-verb /dev/snd/hwC0D0 0x0 PARAMETERS VENDOR_ID
|
|
nid = 0x0, verb = 0xf00, param = 0x0
|
|
value = 0x10ec0262
|
|
|
|
% hda-verb /dev/snd/hwC0D0 2 set_a 0xb080
|
|
nid = 0x2, verb = 0x300, param = 0xb080
|
|
value = 0x0
|
|
|
|
|
|
Although you can issue any verbs with this program, the driver state
|
|
won't be always updated. For example, the volume values are usually
|
|
cached in the driver, and thus changing the widget amp value directly
|
|
via hda-verb won't change the mixer value.
|
|
|
|
The hda-verb program is included now in alsa-tools:
|
|
|
|
* git://git.alsa-project.org/alsa-tools.git
|
|
|
|
Also, the old stand-alone package is found in the ftp directory:
|
|
|
|
* ftp://ftp.suse.com/pub/people/tiwai/misc/
|
|
|
|
Also a git repository is available:
|
|
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/hda-verb.git
|
|
|
|
See README file in the tarball for more details about hda-verb
|
|
program.
|
|
|
|
|
|
hda-analyzer
|
|
------------
|
|
hda-analyzer provides a graphical interface to access the raw HD-audio
|
|
control, based on pyGTK2 binding. It's a more powerful version of
|
|
hda-verb. The program gives you an easy-to-use GUI stuff for showing
|
|
the widget information and adjusting the amp values, as well as the
|
|
proc-compatible output.
|
|
|
|
The hda-analyzer:
|
|
|
|
* https://git.alsa-project.org/?p=alsa.git;a=tree;f=hda-analyzer
|
|
|
|
is a part of alsa.git repository in alsa-project.org:
|
|
|
|
* git://git.alsa-project.org/alsa.git
|
|
|
|
Codecgraph
|
|
----------
|
|
Codecgraph is a utility program to generate a graph and visualizes the
|
|
codec-node connection of a codec chip. It's especially useful when
|
|
you analyze or debug a codec without a proper datasheet. The program
|
|
parses the given codec proc file and converts to SVG via graphiz
|
|
program.
|
|
|
|
The tarball and GIT trees are found in the web page at:
|
|
|
|
* http://helllabs.org/codecgraph/
|
|
|
|
|
|
hda-emu
|
|
-------
|
|
hda-emu is an HD-audio emulator. The main purpose of this program is
|
|
to debug an HD-audio codec without the real hardware. Thus, it
|
|
doesn't emulate the behavior with the real audio I/O, but it just
|
|
dumps the codec register changes and the ALSA-driver internal changes
|
|
at probing and operating the HD-audio driver.
|
|
|
|
The program requires a codec proc-file to simulate. Get a proc file
|
|
for the target codec beforehand, or pick up an example codec from the
|
|
codec proc collections in the tarball. Then, run the program with the
|
|
proc file, and the hda-emu program will start parsing the codec file
|
|
and simulates the HD-audio driver:
|
|
|
|
::
|
|
|
|
% hda-emu codecs/stac9200-dell-d820-laptop
|
|
# Parsing..
|
|
hda_codec: Unknown model for STAC9200, using BIOS defaults
|
|
hda_codec: pin nid 08 bios pin config 40c003fa
|
|
....
|
|
|
|
|
|
The program gives you only a very dumb command-line interface. You
|
|
can get a proc-file dump at the current state, get a list of control
|
|
(mixer) elements, set/get the control element value, simulate the PCM
|
|
operation, the jack plugging simulation, etc.
|
|
|
|
The program is found in the git repository below:
|
|
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/hda-emu.git
|
|
|
|
See README file in the repository for more details about hda-emu
|
|
program.
|
|
|
|
|
|
hda-jack-retask
|
|
---------------
|
|
hda-jack-retask is a user-friendly GUI program to manipulate the
|
|
HD-audio pin control for jack retasking. If you have a problem about
|
|
the jack assignment, try this program and check whether you can get
|
|
useful results. Once when you figure out the proper pin assignment,
|
|
it can be fixed either in the driver code statically or via passing a
|
|
firmware patch file (see "Early Patching" section).
|
|
|
|
The program is included in alsa-tools now:
|
|
|
|
* git://git.alsa-project.org/alsa-tools.git
|