WSL2-Linux-Kernel/arch/arm/mach-msm/board-qsd8x50.c

94 строки
2.5 KiB
C

/* Copyright (c) 2008-2009, Code Aurora Forum. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
* only version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
* 02110-1301, USA.
*/
#include <linux/kernel.h>
#include <linux/irq.h>
#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/io.h>
#include <asm/setup.h>
#include <mach/board.h>
#include <mach/irqs.h>
#include <mach/sirc.h>
#include <mach/gpio.h>
#include "devices.h"
extern struct sys_timer msm_timer;
static struct msm_gpio uart3_config_data[] = {
{ GPIO_CFG(86, 1, GPIO_INPUT, GPIO_PULL_DOWN, GPIO_2MA), "UART2_Rx"},
{ GPIO_CFG(87, 1, GPIO_OUTPUT, GPIO_PULL_DOWN, GPIO_2MA), "UART2_Tx"},
};
static struct platform_device *devices[] __initdata = {
&msm_device_uart3,
};
static void msm8x50_init_uart3(void)
{
msm_gpios_request_enable(uart3_config_data,
ARRAY_SIZE(uart3_config_data));
}
static void __init qsd8x50_map_io(void)
{
msm_map_qsd8x50_io();
msm_clock_init(msm_clocks_8x50, msm_num_clocks_8x50);
}
static void __init qsd8x50_init_irq(void)
{
msm_init_irq();
msm_init_sirc();
}
static void __init qsd8x50_init(void)
{
msm8x50_init_uart3();
platform_add_devices(devices, ARRAY_SIZE(devices));
}
MACHINE_START(QSD8X50_SURF, "QCT QSD8X50 SURF")
#ifdef CONFIG_MSM_DEBUG_UART
.phys_io = MSM_DEBUG_UART_PHYS,
.io_pg_offst = ((MSM_DEBUG_UART_BASE) >> 18) & 0xfffc,
#endif
.boot_params = PHYS_OFFSET + 0x100,
.map_io = qsd8x50_map_io,
.init_irq = qsd8x50_init_irq,
.init_machine = qsd8x50_init,
.timer = &msm_timer,
MACHINE_END
MACHINE_START(QSD8X50A_ST1_5, "QCT QSD8X50A ST1.5")
#ifdef CONFIG_MSM_DEBUG_UART
.phys_io = MSM_DEBUG_UART_PHYS,
.io_pg_offst = ((MSM_DEBUG_UART_BASE) >> 18) & 0xfffc,
#endif
.boot_params = PHYS_OFFSET + 0x100,
.map_io = qsd8x50_map_io,
.init_irq = qsd8x50_init_irq,
.init_machine = qsd8x50_init,
.timer = &msm_timer,
MACHINE_END