WSL2-Linux-Kernel/include/linux/ide.h

1313 строки
41 KiB
C
Исходник Ответственный История

Этот файл содержит невидимые символы Юникода!

Этот файл содержит невидимые символы Юникода, которые могут быть отображены не так, как показано ниже. Если это намеренно, можете спокойно проигнорировать это предупреждение. Используйте кнопку Экранировать, чтобы показать скрытые символы.

#ifndef _IDE_H
#define _IDE_H
/*
* linux/include/linux/ide.h
*
* Copyright (C) 1994-2002 Linus Torvalds & authors
*/
#include <linux/init.h>
#include <linux/ioport.h>
#include <linux/hdreg.h>
#include <linux/hdsmart.h>
#include <linux/blkdev.h>
#include <linux/proc_fs.h>
#include <linux/interrupt.h>
#include <linux/bitops.h>
#include <linux/bio.h>
#include <linux/device.h>
#include <linux/pci.h>
#include <linux/completion.h>
#ifdef CONFIG_BLK_DEV_IDEACPI
#include <acpi/acpi.h>
#endif
#include <asm/byteorder.h>
#include <asm/system.h>
#include <asm/io.h>
#include <asm/semaphore.h>
#include <asm/mutex.h>
#if defined(CRIS) || defined(FRV)
# define SUPPORT_VLB_SYNC 0
#else
# define SUPPORT_VLB_SYNC 1
#endif
/*
* Used to indicate "no IRQ", should be a value that cannot be an IRQ
* number.
*/
#define IDE_NO_IRQ (-1)
typedef unsigned char byte; /* used everywhere */
/*
* Probably not wise to fiddle with these
*/
#define ERROR_MAX 8 /* Max read/write errors per sector */
#define ERROR_RESET 3 /* Reset controller every 4th retry */
#define ERROR_RECAL 1 /* Recalibrate every 2nd retry */
/*
* Tune flags
*/
#define IDE_TUNE_NOAUTO 2
#define IDE_TUNE_AUTO 1
#define IDE_TUNE_DEFAULT 0
/*
* state flags
*/
#define DMA_PIO_RETRY 1 /* retrying in PIO */
#define HWIF(drive) ((ide_hwif_t *)((drive)->hwif))
#define HWGROUP(drive) ((ide_hwgroup_t *)(HWIF(drive)->hwgroup))
/*
* Definitions for accessing IDE controller registers
*/
#define IDE_NR_PORTS (10)
#define IDE_DATA_OFFSET (0)
#define IDE_ERROR_OFFSET (1)
#define IDE_NSECTOR_OFFSET (2)
#define IDE_SECTOR_OFFSET (3)
#define IDE_LCYL_OFFSET (4)
#define IDE_HCYL_OFFSET (5)
#define IDE_SELECT_OFFSET (6)
#define IDE_STATUS_OFFSET (7)
#define IDE_CONTROL_OFFSET (8)
#define IDE_IRQ_OFFSET (9)
#define IDE_FEATURE_OFFSET IDE_ERROR_OFFSET
#define IDE_COMMAND_OFFSET IDE_STATUS_OFFSET
#define IDE_DATA_REG (HWIF(drive)->io_ports[IDE_DATA_OFFSET])
#define IDE_ERROR_REG (HWIF(drive)->io_ports[IDE_ERROR_OFFSET])
#define IDE_NSECTOR_REG (HWIF(drive)->io_ports[IDE_NSECTOR_OFFSET])
#define IDE_SECTOR_REG (HWIF(drive)->io_ports[IDE_SECTOR_OFFSET])
#define IDE_LCYL_REG (HWIF(drive)->io_ports[IDE_LCYL_OFFSET])
#define IDE_HCYL_REG (HWIF(drive)->io_ports[IDE_HCYL_OFFSET])
#define IDE_SELECT_REG (HWIF(drive)->io_ports[IDE_SELECT_OFFSET])
#define IDE_STATUS_REG (HWIF(drive)->io_ports[IDE_STATUS_OFFSET])
#define IDE_CONTROL_REG (HWIF(drive)->io_ports[IDE_CONTROL_OFFSET])
#define IDE_IRQ_REG (HWIF(drive)->io_ports[IDE_IRQ_OFFSET])
#define IDE_FEATURE_REG IDE_ERROR_REG
#define IDE_COMMAND_REG IDE_STATUS_REG
#define IDE_ALTSTATUS_REG IDE_CONTROL_REG
#define IDE_IREASON_REG IDE_NSECTOR_REG
#define IDE_BCOUNTL_REG IDE_LCYL_REG
#define IDE_BCOUNTH_REG IDE_HCYL_REG
#define OK_STAT(stat,good,bad) (((stat)&((good)|(bad)))==(good))
#define BAD_R_STAT (BUSY_STAT | ERR_STAT)
#define BAD_W_STAT (BAD_R_STAT | WRERR_STAT)
#define BAD_STAT (BAD_R_STAT | DRQ_STAT)
#define DRIVE_READY (READY_STAT | SEEK_STAT)
#define BAD_CRC (ABRT_ERR | ICRC_ERR)
#define SATA_NR_PORTS (3) /* 16 possible ?? */
#define SATA_STATUS_OFFSET (0)
#define SATA_STATUS_REG (HWIF(drive)->sata_scr[SATA_STATUS_OFFSET])
#define SATA_ERROR_OFFSET (1)
#define SATA_ERROR_REG (HWIF(drive)->sata_scr[SATA_ERROR_OFFSET])
#define SATA_CONTROL_OFFSET (2)
#define SATA_CONTROL_REG (HWIF(drive)->sata_scr[SATA_CONTROL_OFFSET])
#define SATA_MISC_OFFSET (0)
#define SATA_MISC_REG (HWIF(drive)->sata_misc[SATA_MISC_OFFSET])
#define SATA_PHY_OFFSET (1)
#define SATA_PHY_REG (HWIF(drive)->sata_misc[SATA_PHY_OFFSET])
#define SATA_IEN_OFFSET (2)
#define SATA_IEN_REG (HWIF(drive)->sata_misc[SATA_IEN_OFFSET])
/*
* Our Physical Region Descriptor (PRD) table should be large enough
* to handle the biggest I/O request we are likely to see. Since requests
* can have no more than 256 sectors, and since the typical blocksize is
* two or more sectors, we could get by with a limit of 128 entries here for
* the usual worst case. Most requests seem to include some contiguous blocks,
* further reducing the number of table entries required.
*
* The driver reverts to PIO mode for individual requests that exceed
* this limit (possible with 512 byte blocksizes, eg. MSDOS f/s), so handling
* 100% of all crazy scenarios here is not necessary.
*
* As it turns out though, we must allocate a full 4KB page for this,
* so the two PRD tables (ide0 & ide1) will each get half of that,
* allowing each to have about 256 entries (8 bytes each) from this.
*/
#define PRD_BYTES 8
#define PRD_ENTRIES 256
/*
* Some more useful definitions
*/
#define PARTN_BITS 6 /* number of minor dev bits for partitions */
#define MAX_DRIVES 2 /* per interface; 2 assumed by lots of code */
#define SECTOR_SIZE 512
#define SECTOR_WORDS (SECTOR_SIZE / 4) /* number of 32bit words per sector */
#define IDE_LARGE_SEEK(b1,b2,t) (((b1) > (b2) + (t)) || ((b2) > (b1) + (t)))
/*
* Timeouts for various operations:
*/
#define WAIT_DRQ (HZ/10) /* 100msec - spec allows up to 20ms */
#define WAIT_READY (5*HZ) /* 5sec - some laptops are very slow */
#define WAIT_PIDENTIFY (10*HZ) /* 10sec - should be less than 3ms (?), if all ATAPI CD is closed at boot */
#define WAIT_WORSTCASE (30*HZ) /* 30sec - worst case when spinning up */
#define WAIT_CMD (10*HZ) /* 10sec - maximum wait for an IRQ to happen */
#define WAIT_MIN_SLEEP (2*HZ/100) /* 20msec - minimum sleep time */
/*
* Check for an interrupt and acknowledge the interrupt status
*/
struct hwif_s;
typedef int (ide_ack_intr_t)(struct hwif_s *);
/*
* hwif_chipset_t is used to keep track of the specific hardware
* chipset used by each IDE interface, if known.
*/
enum { ide_unknown, ide_generic, ide_pci,
ide_cmd640, ide_dtc2278, ide_ali14xx,
ide_qd65xx, ide_umc8672, ide_ht6560b,
ide_rz1000, ide_trm290,
ide_cmd646, ide_cy82c693, ide_4drives,
ide_pmac, ide_etrax100, ide_acorn,
ide_au1xxx, ide_forced
};
typedef u8 hwif_chipset_t;
/*
* Structure to hold all information about the location of this port
*/
typedef struct hw_regs_s {
unsigned long io_ports[IDE_NR_PORTS]; /* task file registers */
int irq; /* our irq number */
ide_ack_intr_t *ack_intr; /* acknowledge interrupt */
hwif_chipset_t chipset;
struct device *dev;
} hw_regs_t;
struct hwif_s * ide_find_port(unsigned long);
void ide_init_port_data(struct hwif_s *, unsigned int);
void ide_init_port_hw(struct hwif_s *, hw_regs_t *);
struct ide_drive_s;
int ide_register_hw(hw_regs_t *, void (*)(struct ide_drive_s *),
struct hwif_s **);
void ide_setup_ports( hw_regs_t *hw,
unsigned long base,
int *offsets,
unsigned long ctrl,
unsigned long intr,
ide_ack_intr_t *ack_intr,
#if 0
ide_io_ops_t *iops,
#endif
int irq);
static inline void ide_std_init_ports(hw_regs_t *hw,
unsigned long io_addr,
unsigned long ctl_addr)
{
unsigned int i;
for (i = IDE_DATA_OFFSET; i <= IDE_STATUS_OFFSET; i++)
hw->io_ports[i] = io_addr++;
hw->io_ports[IDE_CONTROL_OFFSET] = ctl_addr;
}
#include <asm/ide.h>
#if !defined(MAX_HWIFS) || defined(CONFIG_EMBEDDED)
#undef MAX_HWIFS
#define MAX_HWIFS CONFIG_IDE_MAX_HWIFS
#endif
/* needed on alpha, x86/x86_64, ia64, mips, ppc32 and sh */
#ifndef IDE_ARCH_OBSOLETE_DEFAULTS
# define ide_default_io_base(index) (0)
# define ide_default_irq(base) (0)
# define ide_init_default_irq(base) (0)
#endif
#ifdef CONFIG_IDE_ARCH_OBSOLETE_INIT
static inline void ide_init_hwif_ports(hw_regs_t *hw,
unsigned long io_addr,
unsigned long ctl_addr,
int *irq)
{
if (!ctl_addr)
ide_std_init_ports(hw, io_addr, ide_default_io_ctl(io_addr));
else
ide_std_init_ports(hw, io_addr, ctl_addr);
if (irq)
*irq = 0;
hw->io_ports[IDE_IRQ_OFFSET] = 0;
#ifdef CONFIG_PPC32
if (ppc_ide_md.ide_init_hwif)
ppc_ide_md.ide_init_hwif(hw, io_addr, ctl_addr, irq);
#endif
}
#else
static inline void ide_init_hwif_ports(hw_regs_t *hw,
unsigned long io_addr,
unsigned long ctl_addr,
int *irq)
{
if (io_addr || ctl_addr)
printk(KERN_WARNING "%s: must not be called\n", __FUNCTION__);
}
#endif /* CONFIG_IDE_ARCH_OBSOLETE_INIT */
/* Currently only m68k, apus and m8xx need it */
#ifndef IDE_ARCH_ACK_INTR
# define ide_ack_intr(hwif) (1)
#endif
/* Currently only Atari needs it */
#ifndef IDE_ARCH_LOCK
# define ide_release_lock() do {} while (0)
# define ide_get_lock(hdlr, data) do {} while (0)
#endif /* IDE_ARCH_LOCK */
/*
* Now for the data we need to maintain per-drive: ide_drive_t
*/
#define ide_scsi 0x21
#define ide_disk 0x20
#define ide_optical 0x7
#define ide_cdrom 0x5
#define ide_tape 0x1
#define ide_floppy 0x0
/*
* Special Driver Flags
*
* set_geometry : respecify drive geometry
* recalibrate : seek to cyl 0
* set_multmode : set multmode count
* set_tune : tune interface for drive
* serviced : service command
* reserved : unused
*/
typedef union {
unsigned all : 8;
struct {
unsigned set_geometry : 1;
unsigned recalibrate : 1;
unsigned set_multmode : 1;
unsigned set_tune : 1;
unsigned serviced : 1;
unsigned reserved : 3;
} b;
} special_t;
/*
* ATA-IDE Select Register, aka Device-Head
*
* head : always zeros here
* unit : drive select number: 0/1
* bit5 : always 1
* lba : using LBA instead of CHS
* bit7 : always 1
*/
typedef union {
unsigned all : 8;
struct {
#if defined(__LITTLE_ENDIAN_BITFIELD)
unsigned head : 4;
unsigned unit : 1;
unsigned bit5 : 1;
unsigned lba : 1;
unsigned bit7 : 1;
#elif defined(__BIG_ENDIAN_BITFIELD)
unsigned bit7 : 1;
unsigned lba : 1;
unsigned bit5 : 1;
unsigned unit : 1;
unsigned head : 4;
#else
#error "Please fix <asm/byteorder.h>"
#endif
} b;
} select_t, ata_select_t;
/*
* Status returned from various ide_ functions
*/
typedef enum {
ide_stopped, /* no drive operation was started */
ide_started, /* a drive operation was started, handler was set */
} ide_startstop_t;
struct ide_driver_s;
struct ide_settings_s;
#ifdef CONFIG_BLK_DEV_IDEACPI
struct ide_acpi_drive_link;
struct ide_acpi_hwif_link;
#endif
typedef struct ide_drive_s {
char name[4]; /* drive name, such as "hda" */
char driver_req[10]; /* requests specific driver */
struct request_queue *queue; /* request queue */
struct request *rq; /* current request */
struct ide_drive_s *next; /* circular list of hwgroup drives */
void *driver_data; /* extra driver data */
struct hd_driveid *id; /* drive model identification info */
#ifdef CONFIG_IDE_PROC_FS
struct proc_dir_entry *proc; /* /proc/ide/ directory entry */
struct ide_settings_s *settings;/* /proc/ide/ drive settings */
#endif
struct hwif_s *hwif; /* actually (ide_hwif_t *) */
unsigned long sleep; /* sleep until this time */
unsigned long service_start; /* time we started last request */
unsigned long service_time; /* service time of last request */
unsigned long timeout; /* max time to wait for irq */
special_t special; /* special action flags */
select_t select; /* basic drive/head select reg value */
u8 keep_settings; /* restore settings after drive reset */
u8 using_dma; /* disk is using dma for read/write */
u8 retry_pio; /* retrying dma capable host in pio */
u8 state; /* retry state */
u8 waiting_for_dma; /* dma currently in progress */
u8 unmask; /* okay to unmask other irqs */
u8 noflush; /* don't attempt flushes */
u8 dsc_overlap; /* DSC overlap */
u8 nice1; /* give potential excess bandwidth */
unsigned present : 1; /* drive is physically present */
unsigned dead : 1; /* device ejected hint */
unsigned id_read : 1; /* 1=id read from disk 0 = synthetic */
unsigned noprobe : 1; /* from: hdx=noprobe */
unsigned removable : 1; /* 1 if need to do check_media_change */
unsigned attach : 1; /* needed for removable devices */
unsigned forced_geom : 1; /* 1 if hdx=c,h,s was given at boot */
unsigned no_unmask : 1; /* disallow setting unmask bit */
unsigned no_io_32bit : 1; /* disallow enabling 32bit I/O */
unsigned atapi_overlap : 1; /* ATAPI overlap (not supported) */
unsigned nice0 : 1; /* give obvious excess bandwidth */
unsigned nice2 : 1; /* give a share in our own bandwidth */
unsigned doorlocking : 1; /* for removable only: door lock/unlock works */
unsigned nodma : 1; /* disallow DMA */
unsigned autotune : 2; /* 0=default, 1=autotune, 2=noautotune */
unsigned remap_0_to_1 : 1; /* 0=noremap, 1=remap 0->1 (for EZDrive) */
unsigned blocked : 1; /* 1=powermanagment told us not to do anything, so sleep nicely */
unsigned vdma : 1; /* 1=doing PIO over DMA 0=doing normal DMA */
unsigned scsi : 1; /* 0=default, 1=ide-scsi emulation */
unsigned sleeping : 1; /* 1=sleeping & sleep field valid */
unsigned post_reset : 1;
unsigned udma33_warned : 1;
u8 addressing; /* 0=28-bit, 1=48-bit, 2=48-bit doing 28-bit */
u8 quirk_list; /* considered quirky, set for a specific host */
u8 init_speed; /* transfer rate set at boot */
u8 current_speed; /* current transfer rate set */
u8 desired_speed; /* desired transfer rate set */
u8 dn; /* now wide spread use */
u8 wcache; /* status of write cache */
u8 acoustic; /* acoustic management */
u8 media; /* disk, cdrom, tape, floppy, ... */
u8 ctl; /* "normal" value for IDE_CONTROL_REG */
u8 ready_stat; /* min status value for drive ready */
u8 mult_count; /* current multiple sector setting */
u8 mult_req; /* requested multiple sector setting */
u8 tune_req; /* requested drive tuning setting */
u8 io_32bit; /* 0=16-bit, 1=32-bit, 2/3=32bit+sync */
u8 bad_wstat; /* used for ignoring WRERR_STAT */
u8 nowerr; /* used for ignoring WRERR_STAT */
u8 sect0; /* offset of first sector for DM6:DDO */
u8 head; /* "real" number of heads */
u8 sect; /* "real" sectors per track */
u8 bios_head; /* BIOS/fdisk/LILO number of heads */
u8 bios_sect; /* BIOS/fdisk/LILO sectors per track */
unsigned int bios_cyl; /* BIOS/fdisk/LILO number of cyls */
unsigned int cyl; /* "real" number of cyls */
unsigned int drive_data; /* used by set_pio_mode/selectproc */
unsigned int failures; /* current failure count */
unsigned int max_failures; /* maximum allowed failure count */
u64 probed_capacity;/* initial reported media capacity (ide-cd only currently) */
u64 capacity64; /* total number of sectors */
int lun; /* logical unit */
int crc_count; /* crc counter to reduce drive speed */
#ifdef CONFIG_BLK_DEV_IDEACPI
struct ide_acpi_drive_link *acpidata;
#endif
struct list_head list;
struct device gendev;
struct completion gendev_rel_comp; /* to deal with device release() */
} ide_drive_t;
#define to_ide_device(dev)container_of(dev, ide_drive_t, gendev)
#define IDE_CHIPSET_PCI_MASK \
((1<<ide_pci)|(1<<ide_cmd646)|(1<<ide_ali14xx))
#define IDE_CHIPSET_IS_PCI(c) ((IDE_CHIPSET_PCI_MASK >> (c)) & 1)
struct ide_port_info;
typedef struct hwif_s {
struct hwif_s *next; /* for linked-list in ide_hwgroup_t */
struct hwif_s *mate; /* other hwif from same PCI chip */
struct hwgroup_s *hwgroup; /* actually (ide_hwgroup_t *) */
struct proc_dir_entry *proc; /* /proc/ide/ directory entry */
char name[6]; /* name of interface, eg. "ide0" */
/* task file registers for pata and sata */
unsigned long io_ports[IDE_NR_PORTS];
unsigned long sata_scr[SATA_NR_PORTS];
unsigned long sata_misc[SATA_NR_PORTS];
ide_drive_t drives[MAX_DRIVES]; /* drive info */
u8 major; /* our major number */
u8 index; /* 0 for ide0; 1 for ide1; ... */
u8 channel; /* for dual-port chips: 0=primary, 1=secondary */
u8 straight8; /* Alan's straight 8 check */
u8 bus_state; /* power state of the IDE bus */
u32 host_flags;
u8 pio_mask;
u8 ultra_mask;
u8 mwdma_mask;
u8 swdma_mask;
u8 cbl; /* cable type */
hwif_chipset_t chipset; /* sub-module for tuning.. */
struct pci_dev *pci_dev; /* for pci chipsets */
const struct ide_port_info *cds; /* chipset device struct */
ide_ack_intr_t *ack_intr;
void (*rw_disk)(ide_drive_t *, struct request *);
#if 0
ide_hwif_ops_t *hwifops;
#else
/* routine to program host for PIO mode */
void (*set_pio_mode)(ide_drive_t *, const u8);
/* routine to program host for DMA mode */
void (*set_dma_mode)(ide_drive_t *, const u8);
/* tweaks hardware to select drive */
void (*selectproc)(ide_drive_t *);
/* chipset polling based on hba specifics */
int (*reset_poll)(ide_drive_t *);
/* chipset specific changes to default for device-hba resets */
void (*pre_reset)(ide_drive_t *);
/* routine to reset controller after a disk reset */
void (*resetproc)(ide_drive_t *);
/* special host masking for drive selection */
void (*maskproc)(ide_drive_t *, int);
/* check host's drive quirk list */
void (*quirkproc)(ide_drive_t *);
/* driver soft-power interface */
int (*busproc)(ide_drive_t *, int);
#endif
u8 (*mdma_filter)(ide_drive_t *);
u8 (*udma_filter)(ide_drive_t *);
void (*ata_input_data)(ide_drive_t *, void *, u32);
void (*ata_output_data)(ide_drive_t *, void *, u32);
void (*atapi_input_bytes)(ide_drive_t *, void *, u32);
void (*atapi_output_bytes)(ide_drive_t *, void *, u32);
void (*dma_host_set)(ide_drive_t *, int);
int (*dma_setup)(ide_drive_t *);
void (*dma_exec_cmd)(ide_drive_t *, u8);
void (*dma_start)(ide_drive_t *);
int (*ide_dma_end)(ide_drive_t *drive);
int (*ide_dma_test_irq)(ide_drive_t *drive);
void (*ide_dma_clear_irq)(ide_drive_t *drive);
void (*dma_lost_irq)(ide_drive_t *drive);
void (*dma_timeout)(ide_drive_t *drive);
void (*OUTB)(u8 addr, unsigned long port);
void (*OUTBSYNC)(ide_drive_t *drive, u8 addr, unsigned long port);
void (*OUTW)(u16 addr, unsigned long port);
void (*OUTSW)(unsigned long port, void *addr, u32 count);
void (*OUTSL)(unsigned long port, void *addr, u32 count);
u8 (*INB)(unsigned long port);
u16 (*INW)(unsigned long port);
void (*INSW)(unsigned long port, void *addr, u32 count);
void (*INSL)(unsigned long port, void *addr, u32 count);
/* dma physical region descriptor table (cpu view) */
unsigned int *dmatable_cpu;
/* dma physical region descriptor table (dma view) */
dma_addr_t dmatable_dma;
/* Scatter-gather list used to build the above */
struct scatterlist *sg_table;
int sg_max_nents; /* Maximum number of entries in it */
int sg_nents; /* Current number of entries in it */
int sg_dma_direction; /* dma transfer direction */
/* data phase of the active command (currently only valid for PIO/DMA) */
int data_phase;
unsigned int nsect;
unsigned int nleft;
struct scatterlist *cursg;
unsigned int cursg_ofs;
int rqsize; /* max sectors per request */
int irq; /* our irq number */
unsigned long dma_base; /* base addr for dma ports */
unsigned long dma_command; /* dma command register */
unsigned long dma_vendor1; /* dma vendor 1 register */
unsigned long dma_status; /* dma status register */
unsigned long dma_vendor3; /* dma vendor 3 register */
unsigned long dma_prdtable; /* actual prd table address */
unsigned long config_data; /* for use by chipset-specific code */
unsigned long select_data; /* for use by chipset-specific code */
unsigned long extra_base; /* extra addr for dma ports */
unsigned extra_ports; /* number of extra dma ports */
unsigned noprobe : 1; /* don't probe for this interface */
unsigned present : 1; /* this interface exists */
unsigned hold : 1; /* this interface is always present */
unsigned serialized : 1; /* serialized all channel operation */
unsigned sharing_irq: 1; /* 1 = sharing irq with another hwif */
unsigned reset : 1; /* reset after probe */
unsigned auto_poll : 1; /* supports nop auto-poll */
unsigned sg_mapped : 1; /* sg_table and sg_nents are ready */
unsigned no_io_32bit : 1; /* 1 = can not do 32-bit IO ops */
unsigned mmio : 1; /* host uses MMIO */
struct device gendev;
struct completion gendev_rel_comp; /* To deal with device release() */
void *hwif_data; /* extra hwif data */
unsigned dma;
#ifdef CONFIG_BLK_DEV_IDEACPI
struct ide_acpi_hwif_link *acpidata;
#endif
} ____cacheline_internodealigned_in_smp ide_hwif_t;
/*
* internal ide interrupt handler type
*/
typedef ide_startstop_t (ide_handler_t)(ide_drive_t *);
typedef int (ide_expiry_t)(ide_drive_t *);
typedef struct hwgroup_s {
/* irq handler, if active */
ide_startstop_t (*handler)(ide_drive_t *);
/* irq handler, suspended if active */
ide_startstop_t (*handler_save)(ide_drive_t *);
/* BOOL: protects all fields below */
volatile int busy;
/* BOOL: wake us up on timer expiry */
unsigned int sleeping : 1;
/* BOOL: polling active & poll_timeout field valid */
unsigned int polling : 1;
/* BOOL: in a polling reset situation. Must not trigger another reset yet */
unsigned int resetting : 1;
/* current drive */
ide_drive_t *drive;
/* ptr to current hwif in linked-list */
ide_hwif_t *hwif;
/* for pci chipsets */
struct pci_dev *pci_dev;
/* current request */
struct request *rq;
/* failsafe timer */
struct timer_list timer;
/* local copy of current write rq */
struct request wrq;
/* timeout value during long polls */
unsigned long poll_timeout;
/* queried upon timeouts */
int (*expiry)(ide_drive_t *);
/* ide_system_bus_speed */
int pio_clock;
int req_gen;
int req_gen_timer;
unsigned char cmd_buf[4];
} ide_hwgroup_t;
typedef struct ide_driver_s ide_driver_t;
extern struct mutex ide_setting_mtx;
int set_io_32bit(ide_drive_t *, int);
int set_pio_mode(ide_drive_t *, int);
int set_using_dma(ide_drive_t *, int);
#ifdef CONFIG_IDE_PROC_FS
/*
* configurable drive settings
*/
#define TYPE_INT 0
#define TYPE_BYTE 1
#define TYPE_SHORT 2
#define SETTING_READ (1 << 0)
#define SETTING_WRITE (1 << 1)
#define SETTING_RW (SETTING_READ | SETTING_WRITE)
typedef int (ide_procset_t)(ide_drive_t *, int);
typedef struct ide_settings_s {
char *name;
int rw;
int data_type;
int min;
int max;
int mul_factor;
int div_factor;
void *data;
ide_procset_t *set;
int auto_remove;
struct ide_settings_s *next;
} ide_settings_t;
int ide_add_setting(ide_drive_t *, const char *, int, int, int, int, int, int, void *, ide_procset_t *set);
/*
* /proc/ide interface
*/
typedef struct {
const char *name;
mode_t mode;
read_proc_t *read_proc;
write_proc_t *write_proc;
} ide_proc_entry_t;
void proc_ide_create(void);
void proc_ide_destroy(void);
void ide_proc_register_port(ide_hwif_t *);
void ide_proc_unregister_port(ide_hwif_t *);
void ide_proc_register_driver(ide_drive_t *, ide_driver_t *);
void ide_proc_unregister_driver(ide_drive_t *, ide_driver_t *);
void ide_add_generic_settings(ide_drive_t *);
read_proc_t proc_ide_read_capacity;
read_proc_t proc_ide_read_geometry;
#ifdef CONFIG_BLK_DEV_IDEPCI
void ide_pci_create_host_proc(const char *, get_info_t *);
#endif
/*
* Standard exit stuff:
*/
#define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) \
{ \
len -= off; \
if (len < count) { \
*eof = 1; \
if (len <= 0) \
return 0; \
} else \
len = count; \
*start = page + off; \
return len; \
}
#else
static inline void proc_ide_create(void) { ; }
static inline void proc_ide_destroy(void) { ; }
static inline void ide_proc_register_port(ide_hwif_t *hwif) { ; }
static inline void ide_proc_unregister_port(ide_hwif_t *hwif) { ; }
static inline void ide_proc_register_driver(ide_drive_t *drive, ide_driver_t *driver) { ; }
static inline void ide_proc_unregister_driver(ide_drive_t *drive, ide_driver_t *driver) { ; }
static inline void ide_add_generic_settings(ide_drive_t *drive) { ; }
#define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) return 0;
#endif
/*
* Power Management step value (rq->pm->pm_step).
*
* The step value starts at 0 (ide_pm_state_start_suspend) for a
* suspend operation or 1000 (ide_pm_state_start_resume) for a
* resume operation.
*
* For each step, the core calls the subdriver start_power_step() first.
* This can return:
* - ide_stopped : In this case, the core calls us back again unless
* step have been set to ide_power_state_completed.
* - ide_started : In this case, the channel is left busy until an
* async event (interrupt) occurs.
* Typically, start_power_step() will issue a taskfile request with
* do_rw_taskfile().
*
* Upon reception of the interrupt, the core will call complete_power_step()
* with the error code if any. This routine should update the step value
* and return. It should not start a new request. The core will call
* start_power_step for the new step value, unless step have been set to
* ide_power_state_completed.
*
* Subdrivers are expected to define their own additional power
* steps from 1..999 for suspend and from 1001..1999 for resume,
* other values are reserved for future use.
*/
enum {
ide_pm_state_completed = -1,
ide_pm_state_start_suspend = 0,
ide_pm_state_start_resume = 1000,
};
/*
* Subdrivers support.
*
* The gendriver.owner field should be set to the module owner of this driver.
* The gendriver.name field should be set to the name of this driver
*/
struct ide_driver_s {
const char *version;
u8 media;
unsigned supports_dsc_overlap : 1;
ide_startstop_t (*do_request)(ide_drive_t *, struct request *, sector_t);
int (*end_request)(ide_drive_t *, int, int);
ide_startstop_t (*error)(ide_drive_t *, struct request *rq, u8, u8);
ide_startstop_t (*abort)(ide_drive_t *, struct request *rq);
struct device_driver gen_driver;
int (*probe)(ide_drive_t *);
void (*remove)(ide_drive_t *);
void (*resume)(ide_drive_t *);
void (*shutdown)(ide_drive_t *);
#ifdef CONFIG_IDE_PROC_FS
ide_proc_entry_t *proc;
#endif
};
#define to_ide_driver(drv) container_of(drv, ide_driver_t, gen_driver)
int generic_ide_ioctl(ide_drive_t *, struct file *, struct block_device *, unsigned, unsigned long);
/*
* ide_hwifs[] is the master data structure used to keep track
* of just about everything in ide.c. Whenever possible, routines
* should be using pointers to a drive (ide_drive_t *) or
* pointers to a hwif (ide_hwif_t *), rather than indexing this
* structure directly (the allocation/layout may change!).
*
*/
#ifndef _IDE_C
extern ide_hwif_t ide_hwifs[]; /* master data repository */
#endif
extern int noautodma;
extern int ide_end_request (ide_drive_t *drive, int uptodate, int nrsecs);
int ide_end_dequeued_request(ide_drive_t *drive, struct request *rq,
int uptodate, int nr_sectors);
extern void ide_set_handler (ide_drive_t *drive, ide_handler_t *handler, unsigned int timeout, ide_expiry_t *expiry);
void ide_execute_command(ide_drive_t *, u8, ide_handler_t *, unsigned int,
ide_expiry_t *);
ide_startstop_t __ide_error(ide_drive_t *, struct request *, u8, u8);
ide_startstop_t ide_error (ide_drive_t *drive, const char *msg, byte stat);
ide_startstop_t __ide_abort(ide_drive_t *, struct request *);
extern ide_startstop_t ide_abort(ide_drive_t *, const char *);
extern void ide_fix_driveid(struct hd_driveid *);
extern void ide_fixstring(u8 *, const int, const int);
int ide_wait_stat(ide_startstop_t *, ide_drive_t *, u8, u8, unsigned long);
extern ide_startstop_t ide_do_reset (ide_drive_t *);
extern void ide_init_drive_cmd (struct request *rq);
/*
* "action" parameter type for ide_do_drive_cmd() below.
*/
typedef enum {
ide_wait, /* insert rq at end of list, and wait for it */
ide_preempt, /* insert rq in front of current request */
ide_head_wait, /* insert rq in front of current request and wait for it */
ide_end /* insert rq at end of list, but don't wait for it */
} ide_action_t;
extern int ide_do_drive_cmd(ide_drive_t *, struct request *, ide_action_t);
extern void ide_end_drive_cmd(ide_drive_t *, u8, u8);
enum {
IDE_TFLAG_LBA48 = (1 << 0),
IDE_TFLAG_NO_SELECT_MASK = (1 << 1),
IDE_TFLAG_FLAGGED = (1 << 2),
IDE_TFLAG_OUT_DATA = (1 << 3),
IDE_TFLAG_OUT_HOB_FEATURE = (1 << 4),
IDE_TFLAG_OUT_HOB_NSECT = (1 << 5),
IDE_TFLAG_OUT_HOB_LBAL = (1 << 6),
IDE_TFLAG_OUT_HOB_LBAM = (1 << 7),
IDE_TFLAG_OUT_HOB_LBAH = (1 << 8),
IDE_TFLAG_OUT_HOB = IDE_TFLAG_OUT_HOB_FEATURE |
IDE_TFLAG_OUT_HOB_NSECT |
IDE_TFLAG_OUT_HOB_LBAL |
IDE_TFLAG_OUT_HOB_LBAM |
IDE_TFLAG_OUT_HOB_LBAH,
IDE_TFLAG_OUT_FEATURE = (1 << 9),
IDE_TFLAG_OUT_NSECT = (1 << 10),
IDE_TFLAG_OUT_LBAL = (1 << 11),
IDE_TFLAG_OUT_LBAM = (1 << 12),
IDE_TFLAG_OUT_LBAH = (1 << 13),
IDE_TFLAG_OUT_TF = IDE_TFLAG_OUT_FEATURE |
IDE_TFLAG_OUT_NSECT |
IDE_TFLAG_OUT_LBAL |
IDE_TFLAG_OUT_LBAM |
IDE_TFLAG_OUT_LBAH,
IDE_TFLAG_OUT_DEVICE = (1 << 14),
IDE_TFLAG_WRITE = (1 << 15),
IDE_TFLAG_FLAGGED_SET_IN_FLAGS = (1 << 16),
IDE_TFLAG_IN_DATA = (1 << 17),
IDE_TFLAG_CUSTOM_HANDLER = (1 << 18),
IDE_TFLAG_DMA_PIO_FALLBACK = (1 << 19),
IDE_TFLAG_IN_HOB_FEATURE = (1 << 20),
IDE_TFLAG_IN_HOB_NSECT = (1 << 21),
IDE_TFLAG_IN_HOB_LBAL = (1 << 22),
IDE_TFLAG_IN_HOB_LBAM = (1 << 23),
IDE_TFLAG_IN_HOB_LBAH = (1 << 24),
IDE_TFLAG_IN_HOB_LBA = IDE_TFLAG_IN_HOB_LBAL |
IDE_TFLAG_IN_HOB_LBAM |
IDE_TFLAG_IN_HOB_LBAH,
IDE_TFLAG_IN_HOB = IDE_TFLAG_IN_HOB_FEATURE |
IDE_TFLAG_IN_HOB_NSECT |
IDE_TFLAG_IN_HOB_LBA,
IDE_TFLAG_IN_NSECT = (1 << 25),
IDE_TFLAG_IN_LBAL = (1 << 26),
IDE_TFLAG_IN_LBAM = (1 << 27),
IDE_TFLAG_IN_LBAH = (1 << 28),
IDE_TFLAG_IN_LBA = IDE_TFLAG_IN_LBAL |
IDE_TFLAG_IN_LBAM |
IDE_TFLAG_IN_LBAH,
IDE_TFLAG_IN_TF = IDE_TFLAG_IN_NSECT |
IDE_TFLAG_IN_LBA,
IDE_TFLAG_IN_DEVICE = (1 << 29),
IDE_TFLAG_HOB = IDE_TFLAG_OUT_HOB |
IDE_TFLAG_IN_HOB,
IDE_TFLAG_TF = IDE_TFLAG_OUT_TF |
IDE_TFLAG_IN_TF,
IDE_TFLAG_DEVICE = IDE_TFLAG_OUT_DEVICE |
IDE_TFLAG_IN_DEVICE,
/* force 16-bit I/O operations */
IDE_TFLAG_IO_16BIT = (1 << 30),
};
struct ide_taskfile {
u8 hob_data; /* 0: high data byte (for TASKFILE IOCTL) */
u8 hob_feature; /* 1-5: additional data to support LBA48 */
u8 hob_nsect;
u8 hob_lbal;
u8 hob_lbam;
u8 hob_lbah;
u8 data; /* 6: low data byte (for TASKFILE IOCTL) */
union { /*  7: */
u8 error; /* read: error */
u8 feature; /* write: feature */
};
u8 nsect; /* 8: number of sectors */
u8 lbal; /* 9: LBA low */
u8 lbam; /* 10: LBA mid */
u8 lbah; /* 11: LBA high */
u8 device; /* 12: device select */
union { /* 13: */
u8 status; /*  read: status  */
u8 command; /* write: command */
};
};
typedef struct ide_task_s {
union {
struct ide_taskfile tf;
u8 tf_array[14];
};
u32 tf_flags;
int data_phase;
struct request *rq; /* copy of request */
void *special; /* valid_t generally */
} ide_task_t;
void ide_tf_load(ide_drive_t *, ide_task_t *);
void ide_tf_read(ide_drive_t *, ide_task_t *);
extern void SELECT_DRIVE(ide_drive_t *);
extern void SELECT_MASK(ide_drive_t *, int);
extern int drive_is_ready(ide_drive_t *);
void ide_pktcmd_tf_load(ide_drive_t *, u32, u16, u8);
ide_startstop_t do_rw_taskfile(ide_drive_t *, ide_task_t *);
void task_end_request(ide_drive_t *, struct request *, u8);
u8 wait_drive_not_busy(ide_drive_t *);
int ide_raw_taskfile(ide_drive_t *, ide_task_t *, u8 *, u16);
int ide_no_data_taskfile(ide_drive_t *, ide_task_t *);
int ide_taskfile_ioctl(ide_drive_t *, unsigned int, unsigned long);
int ide_cmd_ioctl(ide_drive_t *, unsigned int, unsigned long);
int ide_task_ioctl(ide_drive_t *, unsigned int, unsigned long);
extern int system_bus_clock(void);
extern int ide_driveid_update(ide_drive_t *);
extern int ide_ata66_check(ide_drive_t *, ide_task_t *);
extern int ide_config_drive_speed(ide_drive_t *, u8);
extern u8 eighty_ninty_three (ide_drive_t *);
extern int set_transfer(ide_drive_t *, ide_task_t *);
extern int taskfile_lib_get_identify(ide_drive_t *drive, u8 *);
extern int ide_wait_not_busy(ide_hwif_t *hwif, unsigned long timeout);
extern void ide_stall_queue(ide_drive_t *drive, unsigned long timeout);
extern int ide_spin_wait_hwgroup(ide_drive_t *);
extern void ide_timer_expiry(unsigned long);
extern irqreturn_t ide_intr(int irq, void *dev_id);
extern void do_ide_request(struct request_queue *);
void ide_init_disk(struct gendisk *, ide_drive_t *);
#ifdef CONFIG_IDEPCI_PCIBUS_ORDER
extern int ide_scan_direction;
int __init ide_scan_pcibus(void);
extern int __ide_pci_register_driver(struct pci_driver *driver, struct module *owner, const char *mod_name);
#define ide_pci_register_driver(d) __ide_pci_register_driver(d, THIS_MODULE, KBUILD_MODNAME)
#else
#define ide_pci_register_driver(d) pci_register_driver(d)
#endif
void ide_pci_setup_ports(struct pci_dev *, const struct ide_port_info *, int, u8 *);
void ide_setup_pci_noise(struct pci_dev *, const struct ide_port_info *);
extern void default_hwif_iops(ide_hwif_t *);
extern void default_hwif_mmiops(ide_hwif_t *);
extern void default_hwif_transport(ide_hwif_t *);
typedef struct ide_pci_enablebit_s {
u8 reg; /* byte pci reg holding the enable-bit */
u8 mask; /* mask to isolate the enable-bit */
u8 val; /* value of masked reg when "enabled" */
} ide_pci_enablebit_t;
enum {
/* Uses ISA control ports not PCI ones. */
IDE_HFLAG_ISA_PORTS = (1 << 0),
/* single port device */
IDE_HFLAG_SINGLE = (1 << 1),
/* don't use legacy PIO blacklist */
IDE_HFLAG_PIO_NO_BLACKLIST = (1 << 2),
/* don't use conservative PIO "downgrade" */
IDE_HFLAG_PIO_NO_DOWNGRADE = (1 << 3),
/* use PIO8/9 for prefetch off/on */
IDE_HFLAG_ABUSE_PREFETCH = (1 << 4),
/* use PIO6/7 for fast-devsel off/on */
IDE_HFLAG_ABUSE_FAST_DEVSEL = (1 << 5),
/* use 100-102 and 200-202 PIO values to set DMA modes */
IDE_HFLAG_ABUSE_DMA_MODES = (1 << 6),
/*
* keep DMA setting when programming PIO mode, may be used only
* for hosts which have separate PIO and DMA timings (ie. PMAC)
*/
IDE_HFLAG_SET_PIO_MODE_KEEP_DMA = (1 << 7),
/* program host for the transfer mode after programming device */
IDE_HFLAG_POST_SET_MODE = (1 << 8),
/* don't program host/device for the transfer mode ("smart" hosts) */
IDE_HFLAG_NO_SET_MODE = (1 << 9),
/* trust BIOS for programming chipset/device for DMA */
IDE_HFLAG_TRUST_BIOS_FOR_DMA = (1 << 10),
/* host uses VDMA */
IDE_HFLAG_VDMA = (1 << 11),
/* ATAPI DMA is unsupported */
IDE_HFLAG_NO_ATAPI_DMA = (1 << 12),
/* set if host is a "bootable" controller */
IDE_HFLAG_BOOTABLE = (1 << 13),
/* host doesn't support DMA */
IDE_HFLAG_NO_DMA = (1 << 14),
/* check if host is PCI IDE device before allowing DMA */
IDE_HFLAG_NO_AUTODMA = (1 << 15),
/* host is CS5510/CS5520 */
IDE_HFLAG_CS5520 = (1 << 16),
/* no LBA48 */
IDE_HFLAG_NO_LBA48 = (1 << 17),
/* no LBA48 DMA */
IDE_HFLAG_NO_LBA48_DMA = (1 << 18),
/* data FIFO is cleared by an error */
IDE_HFLAG_ERROR_STOPS_FIFO = (1 << 19),
/* serialize ports */
IDE_HFLAG_SERIALIZE = (1 << 20),
/* use legacy IRQs */
IDE_HFLAG_LEGACY_IRQS = (1 << 21),
/* force use of legacy IRQs */
IDE_HFLAG_FORCE_LEGACY_IRQS = (1 << 22),
/* limit LBA48 requests to 256 sectors */
IDE_HFLAG_RQSIZE_256 = (1 << 23),
/* use 32-bit I/O ops */
IDE_HFLAG_IO_32BIT = (1 << 24),
/* unmask IRQs */
IDE_HFLAG_UNMASK_IRQS = (1 << 25),
IDE_HFLAG_ABUSE_SET_DMA_MODE = (1 << 26),
/* host is CY82C693 */
IDE_HFLAG_CY82C693 = (1 << 27),
};
#ifdef CONFIG_BLK_DEV_OFFBOARD
# define IDE_HFLAG_OFF_BOARD IDE_HFLAG_BOOTABLE
#else
# define IDE_HFLAG_OFF_BOARD 0
#endif
struct ide_port_info {
char *name;
unsigned int (*init_chipset)(struct pci_dev *, const char *);
void (*init_iops)(ide_hwif_t *);
void (*init_hwif)(ide_hwif_t *);
void (*init_dma)(ide_hwif_t *, unsigned long);
ide_pci_enablebit_t enablebits[2];
hwif_chipset_t chipset;
u8 extra;
u32 host_flags;
u8 pio_mask;
u8 swdma_mask;
u8 mwdma_mask;
u8 udma_mask;
};
int ide_setup_pci_device(struct pci_dev *, const struct ide_port_info *);
int ide_setup_pci_devices(struct pci_dev *, struct pci_dev *, const struct ide_port_info *);
void ide_map_sg(ide_drive_t *, struct request *);
void ide_init_sg_cmd(ide_drive_t *, struct request *);
#define BAD_DMA_DRIVE 0
#define GOOD_DMA_DRIVE 1
struct drive_list_entry {
const char *id_model;
const char *id_firmware;
};
int ide_in_drive_list(struct hd_driveid *, const struct drive_list_entry *);
#ifdef CONFIG_BLK_DEV_IDEDMA
int __ide_dma_bad_drive(ide_drive_t *);
int ide_id_dma_bug(ide_drive_t *);
u8 ide_find_dma_mode(ide_drive_t *, u8);
static inline u8 ide_max_dma_mode(ide_drive_t *drive)
{
return ide_find_dma_mode(drive, XFER_UDMA_6);
}
void ide_dma_off_quietly(ide_drive_t *);
void ide_dma_off(ide_drive_t *);
void ide_dma_on(ide_drive_t *);
int ide_set_dma(ide_drive_t *);
ide_startstop_t ide_dma_intr(ide_drive_t *);
#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
extern int ide_build_sglist(ide_drive_t *, struct request *);
extern int ide_build_dmatable(ide_drive_t *, struct request *);
extern void ide_destroy_dmatable(ide_drive_t *);
extern int ide_release_dma(ide_hwif_t *);
extern void ide_setup_dma(ide_hwif_t *, unsigned long, unsigned int);
void ide_dma_host_set(ide_drive_t *, int);
extern int ide_dma_setup(ide_drive_t *);
extern void ide_dma_start(ide_drive_t *);
extern int __ide_dma_end(ide_drive_t *);
extern void ide_dma_lost_irq(ide_drive_t *);
extern void ide_dma_timeout(ide_drive_t *);
#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */
#else
static inline int ide_id_dma_bug(ide_drive_t *drive) { return 0; }
static inline u8 ide_find_dma_mode(ide_drive_t *drive, u8 speed) { return 0; }
static inline u8 ide_max_dma_mode(ide_drive_t *drive) { return 0; }
static inline void ide_dma_off_quietly(ide_drive_t *drive) { ; }
static inline void ide_dma_off(ide_drive_t *drive) { ; }
static inline void ide_dma_on(ide_drive_t *drive) { ; }
static inline void ide_dma_verbose(ide_drive_t *drive) { ; }
static inline int ide_set_dma(ide_drive_t *drive) { return 1; }
#endif /* CONFIG_BLK_DEV_IDEDMA */
#ifndef CONFIG_BLK_DEV_IDEDMA_PCI
static inline void ide_release_dma(ide_hwif_t *drive) {;}
#endif
#ifdef CONFIG_BLK_DEV_IDEACPI
extern int ide_acpi_exec_tfs(ide_drive_t *drive);
extern void ide_acpi_get_timing(ide_hwif_t *hwif);
extern void ide_acpi_push_timing(ide_hwif_t *hwif);
extern void ide_acpi_init(ide_hwif_t *hwif);
extern void ide_acpi_set_state(ide_hwif_t *hwif, int on);
#else
static inline int ide_acpi_exec_tfs(ide_drive_t *drive) { return 0; }
static inline void ide_acpi_get_timing(ide_hwif_t *hwif) { ; }
static inline void ide_acpi_push_timing(ide_hwif_t *hwif) { ; }
static inline void ide_acpi_init(ide_hwif_t *hwif) { ; }
static inline void ide_acpi_set_state(ide_hwif_t *hwif, int on) {}
#endif
extern int ide_hwif_request_regions(ide_hwif_t *hwif);
extern void ide_hwif_release_regions(ide_hwif_t* hwif);
extern void ide_unregister (unsigned int index);
void ide_register_region(struct gendisk *);
void ide_unregister_region(struct gendisk *);
void ide_undecoded_slave(ide_drive_t *);
int ide_device_add_all(u8 *idx);
int ide_device_add(u8 idx[4]);
static inline void *ide_get_hwifdata (ide_hwif_t * hwif)
{
return hwif->hwif_data;
}
static inline void ide_set_hwifdata (ide_hwif_t * hwif, void *data)
{
hwif->hwif_data = data;
}
const char *ide_xfer_verbose(u8 mode);
extern void ide_toggle_bounce(ide_drive_t *drive, int on);
extern int ide_set_xfer_rate(ide_drive_t *drive, u8 rate);
static inline int ide_dev_has_iordy(struct hd_driveid *id)
{
return ((id->field_valid & 2) && (id->capability & 8)) ? 1 : 0;
}
static inline int ide_dev_is_sata(struct hd_driveid *id)
{
/*
* See if word 93 is 0 AND drive is at least ATA-5 compatible
* verifying that word 80 by casting it to a signed type --
* this trick allows us to filter out the reserved values of
* 0x0000 and 0xffff along with the earlier ATA revisions...
*/
if (id->hw_config == 0 && (short)id->major_rev_num >= 0x0020)
return 1;
return 0;
}
u64 ide_get_lba_addr(struct ide_taskfile *, int);
u8 ide_dump_status(ide_drive_t *, const char *, u8);
typedef struct ide_pio_timings_s {
int setup_time; /* Address setup (ns) minimum */
int active_time; /* Active pulse (ns) minimum */
int cycle_time; /* Cycle time (ns) minimum = */
/* active + recovery (+ setup for some chips) */
} ide_pio_timings_t;
unsigned int ide_pio_cycle_time(ide_drive_t *, u8);
u8 ide_get_best_pio_mode(ide_drive_t *, u8, u8);
extern const ide_pio_timings_t ide_pio_timings[6];
int ide_set_pio_mode(ide_drive_t *, u8);
int ide_set_dma_mode(ide_drive_t *, u8);
void ide_set_pio(ide_drive_t *, u8);
static inline void ide_set_max_pio(ide_drive_t *drive)
{
ide_set_pio(drive, 255);
}
extern spinlock_t ide_lock;
extern struct mutex ide_cfg_mtx;
/*
* Structure locking:
*
* ide_cfg_mtx and ide_lock together protect changes to
* ide_hwif_t->{next,hwgroup}
* ide_drive_t->next
*
* ide_hwgroup_t->busy: ide_lock
* ide_hwgroup_t->hwif: ide_lock
* ide_hwif_t->mate: constant, no locking
* ide_drive_t->hwif: constant, no locking
*/
#define local_irq_set(flags) do { local_save_flags((flags)); local_irq_enable_in_hardirq(); } while (0)
extern struct bus_type ide_bus_type;
/* check if CACHE FLUSH (EXT) command is supported (bits defined in ATA-6) */
#define ide_id_has_flush_cache(id) ((id)->cfs_enable_2 & 0x3000)
/* some Maxtor disks have bit 13 defined incorrectly so check bit 10 too */
#define ide_id_has_flush_cache_ext(id) \
(((id)->cfs_enable_2 & 0x2400) == 0x2400)
static inline int hwif_to_node(ide_hwif_t *hwif)
{
struct pci_dev *dev = hwif->pci_dev;
return dev ? pcibus_to_node(dev->bus) : -1;
}
static inline ide_drive_t *ide_get_paired_drive(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
return &hwif->drives[(drive->dn ^ 1) & 1];
}
static inline void ide_set_irq(ide_drive_t *drive, int on)
{
drive->hwif->OUTB(drive->ctl | (on ? 0 : 2), IDE_CONTROL_REG);
}
#endif /* _IDE_H */