WSL2-Linux-Kernel/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts

438 строки
7.8 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-only
/dts-v1/;
#include "msm8916-pm8916.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/leds/common.h>
/ {
model = "Longcheer L8150";
compatible = "longcheer,l8150", "qcom,msm8916-v1-qrd/9-v1", "qcom,msm8916";
chassis-type = "handset";
aliases {
serial0 = &blsp1_uart2;
};
chosen {
stdout-path = "serial0";
};
reserved-memory {
/* wcnss.mdt is not relocatable, so it must be loaded at 0x8b600000 */
/delete-node/ wcnss@89300000;
wcnss_mem: wcnss@8b600000 {
reg = <0x0 0x8b600000 0x0 0x600000>;
no-map;
};
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&gpio_keys_default>;
label = "GPIO Buttons";
button-volume-up {
label = "Volume Up";
gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
linux,code = <KEY_VOLUMEUP>;
};
};
reg_ctp: regulator-ctp {
compatible = "regulator-fixed";
regulator-name = "ctp";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
gpio = <&msmgpio 17 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-names = "default";
pinctrl-0 = <&ctp_pwr_en_default>;
};
flash-led-controller {
compatible = "sgmicro,sgm3140";
flash-gpios = <&msmgpio 31 GPIO_ACTIVE_HIGH>;
enable-gpios = <&msmgpio 32 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&camera_flash_default>;
flash_led: led {
function = LED_FUNCTION_FLASH;
color = <LED_COLOR_ID_WHITE>;
flash-max-timeout-us = <250000>;
};
};
};
&blsp_i2c1 {
status = "okay";
led-controller@45 {
compatible = "awinic,aw2013";
reg = <0x45>;
#address-cells = <1>;
#size-cells = <0>;
vcc-supply = <&pm8916_l17>;
led@0 {
reg = <0>;
led-max-microamp = <5000>;
function = LED_FUNCTION_INDICATOR;
color = <LED_COLOR_ID_RED>;
};
led@1 {
reg = <1>;
led-max-microamp = <5000>;
function = LED_FUNCTION_INDICATOR;
color = <LED_COLOR_ID_GREEN>;
};
led@2 {
reg = <2>;
led-max-microamp = <5000>;
function = LED_FUNCTION_INDICATOR;
color = <LED_COLOR_ID_BLUE>;
};
};
};
&blsp_i2c2 {
status = "okay";
accelerometer@10 {
compatible = "bosch,bmc156_accel";
reg = <0x10>;
/*
* For some reason the interrupt line is usually not connected
* to the BMC156. However, there are two pads next to the chip
* that can be shorted to make it work if needed.
*
* interrupt-parent = <&msmgpio>;
* interrupts = <116 IRQ_TYPE_EDGE_RISING>;
*/
pinctrl-names = "default";
pinctrl-0 = <&accel_int_default>;
vdd-supply = <&pm8916_l17>;
vddio-supply = <&pm8916_l6>;
mount-matrix = "0", "1", "0",
"-1", "0", "0",
"0", "0", "1";
};
magnetometer@12 {
compatible = "bosch,bmc156_magn";
reg = <0x12>;
interrupt-parent = <&msmgpio>;
interrupts = <113 IRQ_TYPE_EDGE_RISING>;
pinctrl-names = "default";
pinctrl-0 = <&magn_int_default>;
vdd-supply = <&pm8916_l17>;
vddio-supply = <&pm8916_l6>;
};
light-sensor@23 {
compatible = "liteon,ltr559";
reg = <0x23>;
proximity-near-level = <75>;
interrupt-parent = <&msmgpio>;
interrupts = <115 IRQ_TYPE_EDGE_FALLING>;
pinctrl-names = "default";
pinctrl-0 = <&light_int_default>;
vdd-supply = <&pm8916_l17>;
vio-supply = <&pm8916_l6>;
};
gyroscope@68 {
compatible = "bosch,bmg160";
reg = <0x68>;
interrupt-parent = <&msmgpio>;
interrupts = <23 IRQ_TYPE_EDGE_RISING>,
<22 IRQ_TYPE_EDGE_RISING>;
pinctrl-names = "default";
pinctrl-0 = <&gyro_int_default>;
vdd-supply = <&pm8916_l17>;
vddio-supply = <&pm8916_l6>;
};
};
&blsp_i2c5 {
status = "okay";
rmi4@20 {
compatible = "syna,rmi4-i2c";
reg = <0x20>;
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <&msmgpio>;
interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
vdd-supply = <&reg_ctp>;
vio-supply = <&pm8916_l6>;
pinctrl-names = "default";
pinctrl-0 = <&tp_int_default>;
syna,startup-delay-ms = <10>;
rmi4-f01@1 {
reg = <0x1>;
syna,nosleep-mode = <1>; /* Allow sleeping */
};
rmi4-f12@12 {
reg = <0x12>;
syna,sensor-type = <1>; /* Touchscreen */
};
};
};
&blsp1_uart2 {
status = "okay";
};
&pm8916_resin {
status = "okay";
linux,code = <KEY_VOLUMEDOWN>;
};
&pm8916_usbin {
status = "okay";
};
&pm8916_vib {
status = "okay";
};
&sdhc_1 {
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
};
&sdhc_2 {
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
non-removable;
};
&usb {
status = "okay";
dr_mode = "peripheral";
extcon = <&pm8916_usbin>;
};
&usb_hs_phy {
extcon = <&pm8916_usbin>;
};
&wcnss {
status = "okay";
};
&wcnss_iris {
compatible = "qcom,wcn3620";
};
&smd_rpm_regulators {
vdd_l1_l2_l3-supply = <&pm8916_s3>;
vdd_l4_l5_l6-supply = <&pm8916_s4>;
vdd_l7-supply = <&pm8916_s4>;
s3 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1300000>;
};
s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2100000>;
};
l1 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
};
l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
l4 {
regulator-min-microvolt = <2050000>;
regulator-max-microvolt = <2050000>;
};
l5 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l6 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l8 {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2900000>;
};
l9 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
l10 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2800000>;
};
l11 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
regulator-allow-set-load;
regulator-system-load = <200000>;
};
l12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
};
l13 {
regulator-min-microvolt = <3075000>;
regulator-max-microvolt = <3075000>;
};
l14 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
};
l15 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
};
l16 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
};
l17 {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
};
l18 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2700000>;
};
};
&msmgpio {
accel_int_default: accel-int-default-state {
pins = "gpio116";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
camera_flash_default: camera-flash-default-state {
pins = "gpio31", "gpio32";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
ctp_pwr_en_default: ctp-pwr-en-default-state {
pins = "gpio17";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
gpio_keys_default: gpio-keys-default-state {
pins = "gpio107";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
gyro_int_default: gyro-int-default-state {
pins = "gpio22", "gpio23";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
light_int_default: light-int-default-state {
pins = "gpio115";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
magn_int_default: magn-int-default-state {
pins = "gpio113";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
tp_int_default: tp-int-default-state {
pins = "gpio13";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
};