WSL2-Linux-Kernel/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi

212 строки
4.6 KiB
Plaintext

// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) 2023, Linaro Limited
*/
#include <dt-bindings/input/input.h>
#include <dt-bindings/spmi/spmi.h>
/ {
thermal-zones {
pmm8654au_0_thermal: pm8775-0-thermal {
polling-delay-passive = <100>;
polling-delay = <0>;
thermal-sensors = <&pmm8654au_0_temp_alarm>;
trips {
trip0 {
temperature = <105000>;
hysteresis = <0>;
type = "passive";
};
trip1 {
temperature = <125000>;
hysteresis = <0>;
type = "critical";
};
};
};
pmm8654au_1_thermal: pm8775-1-thermal {
polling-delay-passive = <100>;
polling-delay = <0>;
thermal-sensors = <&pmm8654au_1_temp_alarm>;
trips {
trip0 {
temperature = <105000>;
hysteresis = <0>;
type = "passive";
};
trip1 {
temperature = <125000>;
hysteresis = <0>;
type = "critical";
};
};
};
pmm8654au_2_thermal: pm8775-2-thermal {
polling-delay-passive = <100>;
polling-delay = <0>;
thermal-sensors = <&pmm8654au_2_temp_alarm>;
trips {
trip0 {
temperature = <105000>;
hysteresis = <0>;
type = "passive";
};
trip1 {
temperature = <125000>;
hysteresis = <0>;
type = "critical";
};
};
};
pmm8654au_3_thermal: pm8775-3-thermal {
polling-delay-passive = <100>;
polling-delay = <0>;
thermal-sensors = <&pmm8654au_3_temp_alarm>;
trips {
trip0 {
temperature = <105000>;
hysteresis = <0>;
type = "passive";
};
trip1 {
temperature = <125000>;
hysteresis = <0>;
type = "critical";
};
};
};
};
};
&spmi_bus {
pmm8654au_0: pmic@0 {
compatible = "qcom,pmm8654au", "qcom,spmi-pmic";
reg = <0x0 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
pmm8654au_0_temp_alarm: temp-alarm@a00 {
compatible = "qcom,spmi-temp-alarm";
reg = <0xa00>;
interrupts-extended = <&spmi_bus 0x0 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
#thermal-sensor-cells = <0>;
};
pmm8654au_0_pon: pon@1200 {
compatible = "qcom,pmk8350-pon";
reg = <0x1200>, <0x800>;
reg-names = "hlos", "pbs";
mode-recovery = <0x1>;
mode-bootloader = <0x2>;
pmm8654au_0_pon_pwrkey: pwrkey {
compatible = "qcom,pmk8350-pwrkey";
interrupts-extended = <&spmi_bus 0x0 0x12 0x7 IRQ_TYPE_EDGE_BOTH>;
linux,code = <KEY_POWER>;
debounce = <15625>;
};
pmm8654au_0_pon_resin: resin {
compatible = "qcom,pmk8350-resin";
interrupts-extended = <&spmi_bus 0x0 0x12 0x6 IRQ_TYPE_EDGE_BOTH>;
debounce = <15625>;
status = "disabled";
};
};
pmm8654au_0_gpios: gpio@8800 {
compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
reg = <0x8800>;
gpio-controller;
gpio-ranges = <&pmm8654au_0_gpios 0 0 12>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
pmm8654au_1: pmic@2 {
compatible = "qcom,pmm8654au", "qcom,spmi-pmic";
reg = <0x2 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
pmm8654au_1_temp_alarm: temp-alarm@a00 {
compatible = "qcom,spmi-temp-alarm";
reg = <0xa00>;
interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
#thermal-sensor-cells = <0>;
};
pmm8654au_1_gpios: gpio@8800 {
compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
reg = <0x8800>;
gpio-controller;
gpio-ranges = <&pmm8654au_2_gpios 0 0 12>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
pmm8654au_2: pmic@4 {
compatible = "qcom,pmm8654au", "qcom,spmi-pmic";
reg = <0x4 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
pmm8654au_2_temp_alarm: temp-alarm@a00 {
compatible = "qcom,spmi-temp-alarm";
reg = <0xa00>;
interrupts-extended = <&spmi_bus 0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
#thermal-sensor-cells = <0>;
};
pmm8654au_2_gpios: gpio@8800 {
compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
reg = <0x8800>;
gpio-controller;
gpio-ranges = <&pmm8654au_2_gpios 0 0 12>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
pmm8654au_3: pmic@6 {
compatible = "qcom,pmm8654au", "qcom,spmi-pmic";
reg = <0x6 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
pmm8654au_3_temp_alarm: temp-alarm@a00 {
compatible = "qcom,spmi-temp-alarm";
reg = <0xa00>;
interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
#thermal-sensor-cells = <0>;
};
pmm8654au_3_gpios: gpio@8800 {
compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
reg = <0x8800>;
gpio-controller;
gpio-ranges = <&pmm8654au_3_gpios 0 0 12>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
};