WSL2-Linux-Kernel/drivers/net/slip
Jarod Wilson b3e3893e12 net: use core MTU range checking in misc drivers
firewire-net:
- set min/max_mtu
- remove fwnet_change_mtu

nes:
- set max_mtu
- clean up nes_netdev_change_mtu

xpnet:
- set min/max_mtu
- remove xpnet_dev_change_mtu

hippi:
- set min/max_mtu
- remove hippi_change_mtu

batman-adv:
- set max_mtu
- remove batadv_interface_change_mtu
- initialization is a little async, not 100% certain that max_mtu is set
  in the optimal place, don't have hardware to test with

rionet:
- set min/max_mtu
- remove rionet_change_mtu

slip:
- set min/max_mtu
- streamline sl_change_mtu

um/net_kern:
- remove pointless ndo_change_mtu

hsi/clients/ssi_protocol:
- use core MTU range checking
- remove now redundant ssip_pn_set_mtu

ipoib:
- set a default max MTU value
- Note: ipoib's actual max MTU can vary, depending on if the device is in
  connected mode or not, so we'll just set the max_mtu value to the max
  possible, and let the ndo_change_mtu function continue to validate any new
  MTU change requests with checks for CM or not. Note that ipoib has no
  min_mtu set, and thus, the network core's mtu > 0 check is the only lower
  bounds here.

mptlan:
- use net core MTU range checking
- remove now redundant mpt_lan_change_mtu

fddi:
- min_mtu = 21, max_mtu = 4470
- remove now redundant fddi_change_mtu (including export)

fjes:
- min_mtu = 8192, max_mtu = 65536
- The max_mtu value is actually one over IP_MAX_MTU here, but the idea is to
  get past the core net MTU range checks so fjes_change_mtu can validate a
  new MTU against what it supports (see fjes_support_mtu in fjes_hw.c)

hsr:
- min_mtu = 0 (calls ether_setup, max_mtu is 1500)

f_phonet:
- min_mtu = 6, max_mtu = 65541

u_ether:
- min_mtu = 14, max_mtu = 15412

phonet/pep-gprs:
- min_mtu = 576, max_mtu = 65530
- remove redundant gprs_set_mtu

CC: netdev@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: Stefan Richter <stefanr@s5r6.in-berlin.de>
CC: Faisal Latif <faisal.latif@intel.com>
CC: linux-rdma@vger.kernel.org
CC: Cliff Whickman <cpw@sgi.com>
CC: Robin Holt <robinmholt@gmail.com>
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Marek Lindner <mareklindner@neomailbox.ch>
CC: Simon Wunderlich <sw@simonwunderlich.de>
CC: Antonio Quartulli <a@unstable.cc>
CC: Sathya Prakash <sathya.prakash@broadcom.com>
CC: Chaitra P B <chaitra.basappa@broadcom.com>
CC: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
CC: MPT-FusionLinux.pdl@broadcom.com
CC: Sebastian Reichel <sre@kernel.org>
CC: Felipe Balbi <balbi@kernel.org>
CC: Arvid Brodin <arvid.brodin@alten.se>
CC: Remi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-20 14:51:10 -04:00
..
Kconfig
Makefile
slhc.c
slip.c net: use core MTU range checking in misc drivers 2016-10-20 14:51:10 -04:00
slip.h