729 строки
18 KiB
C
729 строки
18 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* STMicroelectronics pressures driver
|
|
*
|
|
* Copyright 2013 STMicroelectronics Inc.
|
|
*
|
|
* Denis Ciocca <denis.ciocca@st.com>
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/mutex.h>
|
|
#include <linux/sysfs.h>
|
|
#include <linux/iio/iio.h>
|
|
#include <linux/iio/sysfs.h>
|
|
#include <linux/iio/trigger.h>
|
|
#include <asm/unaligned.h>
|
|
|
|
#include <linux/iio/common/st_sensors.h>
|
|
#include "st_pressure.h"
|
|
|
|
/*
|
|
* About determining pressure scaling factors
|
|
* ------------------------------------------
|
|
*
|
|
* Datasheets specify typical pressure sensitivity so that pressure is computed
|
|
* according to the following equation :
|
|
* pressure[mBar] = raw / sensitivity
|
|
* where :
|
|
* raw the 24 bits long raw sampled pressure
|
|
* sensitivity a scaling factor specified by the datasheet in LSB/mBar
|
|
*
|
|
* IIO ABI expects pressure to be expressed as kPascal, hence pressure should be
|
|
* computed according to :
|
|
* pressure[kPascal] = pressure[mBar] / 10
|
|
* = raw / (sensitivity * 10) (1)
|
|
*
|
|
* Finally, st_press_read_raw() returns pressure scaling factor as an
|
|
* IIO_VAL_INT_PLUS_NANO with a zero integral part and "gain" as decimal part.
|
|
* Therefore, from (1), "gain" becomes :
|
|
* gain = 10^9 / (sensitivity * 10)
|
|
* = 10^8 / sensitivity
|
|
*
|
|
* About determining temperature scaling factors and offsets
|
|
* ---------------------------------------------------------
|
|
*
|
|
* Datasheets specify typical temperature sensitivity and offset so that
|
|
* temperature is computed according to the following equation :
|
|
* temp[Celsius] = offset[Celsius] + (raw / sensitivity)
|
|
* where :
|
|
* raw the 16 bits long raw sampled temperature
|
|
* offset a constant specified by the datasheet in degree Celsius
|
|
* (sometimes zero)
|
|
* sensitivity a scaling factor specified by the datasheet in LSB/Celsius
|
|
*
|
|
* IIO ABI expects temperature to be expressed as milli degree Celsius such as
|
|
* user space should compute temperature according to :
|
|
* temp[mCelsius] = temp[Celsius] * 10^3
|
|
* = (offset[Celsius] + (raw / sensitivity)) * 10^3
|
|
* = ((offset[Celsius] * sensitivity) + raw) *
|
|
* (10^3 / sensitivity) (2)
|
|
*
|
|
* IIO ABI expects user space to apply offset and scaling factors to raw samples
|
|
* according to :
|
|
* temp[mCelsius] = (OFFSET + raw) * SCALE
|
|
* where :
|
|
* OFFSET an arbitrary constant exposed by device
|
|
* SCALE an arbitrary scaling factor exposed by device
|
|
*
|
|
* Matching OFFSET and SCALE with members of (2) gives :
|
|
* OFFSET = offset[Celsius] * sensitivity (3)
|
|
* SCALE = 10^3 / sensitivity (4)
|
|
*
|
|
* st_press_read_raw() returns temperature scaling factor as an
|
|
* IIO_VAL_FRACTIONAL with a 10^3 numerator and "gain2" as denominator.
|
|
* Therefore, from (3), "gain2" becomes :
|
|
* gain2 = sensitivity
|
|
*
|
|
* When declared within channel, i.e. for a non zero specified offset,
|
|
* st_press_read_raw() will return the latter as an IIO_VAL_FRACTIONAL such as :
|
|
* numerator = OFFSET * 10^3
|
|
* denominator = 10^3
|
|
* giving from (4):
|
|
* numerator = offset[Celsius] * 10^3 * sensitivity
|
|
* = offset[mCelsius] * gain2
|
|
*/
|
|
|
|
#define MCELSIUS_PER_CELSIUS 1000
|
|
|
|
/* Default pressure sensitivity */
|
|
#define ST_PRESS_LSB_PER_MBAR 4096UL
|
|
#define ST_PRESS_KPASCAL_NANO_SCALE (100000000UL / \
|
|
ST_PRESS_LSB_PER_MBAR)
|
|
|
|
/* Default temperature sensitivity */
|
|
#define ST_PRESS_LSB_PER_CELSIUS 480UL
|
|
#define ST_PRESS_MILLI_CELSIUS_OFFSET 42500UL
|
|
|
|
/* FULLSCALE */
|
|
#define ST_PRESS_FS_AVL_1100MB 1100
|
|
#define ST_PRESS_FS_AVL_1260MB 1260
|
|
|
|
#define ST_PRESS_1_OUT_XL_ADDR 0x28
|
|
#define ST_TEMP_1_OUT_L_ADDR 0x2b
|
|
|
|
/* LPS001WP pressure resolution */
|
|
#define ST_PRESS_LPS001WP_LSB_PER_MBAR 16UL
|
|
/* LPS001WP temperature resolution */
|
|
#define ST_PRESS_LPS001WP_LSB_PER_CELSIUS 64UL
|
|
/* LPS001WP pressure gain */
|
|
#define ST_PRESS_LPS001WP_FS_AVL_PRESS_GAIN \
|
|
(100000000UL / ST_PRESS_LPS001WP_LSB_PER_MBAR)
|
|
/* LPS001WP pressure and temp L addresses */
|
|
#define ST_PRESS_LPS001WP_OUT_L_ADDR 0x28
|
|
#define ST_TEMP_LPS001WP_OUT_L_ADDR 0x2a
|
|
|
|
/* LPS25H pressure and temp L addresses */
|
|
#define ST_PRESS_LPS25H_OUT_XL_ADDR 0x28
|
|
#define ST_TEMP_LPS25H_OUT_L_ADDR 0x2b
|
|
|
|
/* LPS22HB temperature sensitivity */
|
|
#define ST_PRESS_LPS22HB_LSB_PER_CELSIUS 100UL
|
|
|
|
static const struct iio_chan_spec st_press_1_channels[] = {
|
|
{
|
|
.type = IIO_PRESSURE,
|
|
.address = ST_PRESS_1_OUT_XL_ADDR,
|
|
.scan_index = 0,
|
|
.scan_type = {
|
|
.sign = 's',
|
|
.realbits = 24,
|
|
.storagebits = 32,
|
|
.endianness = IIO_LE,
|
|
},
|
|
.info_mask_separate =
|
|
BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
|
|
.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
|
|
},
|
|
{
|
|
.type = IIO_TEMP,
|
|
.address = ST_TEMP_1_OUT_L_ADDR,
|
|
.scan_index = 1,
|
|
.scan_type = {
|
|
.sign = 's',
|
|
.realbits = 16,
|
|
.storagebits = 16,
|
|
.endianness = IIO_LE,
|
|
},
|
|
.info_mask_separate =
|
|
BIT(IIO_CHAN_INFO_RAW) |
|
|
BIT(IIO_CHAN_INFO_SCALE) |
|
|
BIT(IIO_CHAN_INFO_OFFSET),
|
|
.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
|
|
},
|
|
IIO_CHAN_SOFT_TIMESTAMP(2)
|
|
};
|
|
|
|
static const struct iio_chan_spec st_press_lps001wp_channels[] = {
|
|
{
|
|
.type = IIO_PRESSURE,
|
|
.address = ST_PRESS_LPS001WP_OUT_L_ADDR,
|
|
.scan_index = 0,
|
|
.scan_type = {
|
|
.sign = 's',
|
|
.realbits = 16,
|
|
.storagebits = 16,
|
|
.endianness = IIO_LE,
|
|
},
|
|
.info_mask_separate =
|
|
BIT(IIO_CHAN_INFO_RAW) |
|
|
BIT(IIO_CHAN_INFO_SCALE),
|
|
},
|
|
{
|
|
.type = IIO_TEMP,
|
|
.address = ST_TEMP_LPS001WP_OUT_L_ADDR,
|
|
.scan_index = 1,
|
|
.scan_type = {
|
|
.sign = 's',
|
|
.realbits = 16,
|
|
.storagebits = 16,
|
|
.endianness = IIO_LE,
|
|
},
|
|
.info_mask_separate =
|
|
BIT(IIO_CHAN_INFO_RAW) |
|
|
BIT(IIO_CHAN_INFO_SCALE),
|
|
},
|
|
IIO_CHAN_SOFT_TIMESTAMP(2)
|
|
};
|
|
|
|
static const struct iio_chan_spec st_press_lps22hb_channels[] = {
|
|
{
|
|
.type = IIO_PRESSURE,
|
|
.address = ST_PRESS_1_OUT_XL_ADDR,
|
|
.scan_index = 0,
|
|
.scan_type = {
|
|
.sign = 's',
|
|
.realbits = 24,
|
|
.storagebits = 32,
|
|
.endianness = IIO_LE,
|
|
},
|
|
.info_mask_separate =
|
|
BIT(IIO_CHAN_INFO_RAW) |
|
|
BIT(IIO_CHAN_INFO_SCALE),
|
|
.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
|
|
},
|
|
{
|
|
.type = IIO_TEMP,
|
|
.address = ST_TEMP_1_OUT_L_ADDR,
|
|
.scan_index = 1,
|
|
.scan_type = {
|
|
.sign = 's',
|
|
.realbits = 16,
|
|
.storagebits = 16,
|
|
.endianness = IIO_LE,
|
|
},
|
|
.info_mask_separate =
|
|
BIT(IIO_CHAN_INFO_RAW) |
|
|
BIT(IIO_CHAN_INFO_SCALE),
|
|
.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
|
|
},
|
|
IIO_CHAN_SOFT_TIMESTAMP(2)
|
|
};
|
|
|
|
static const struct st_sensor_settings st_press_sensors_settings[] = {
|
|
{
|
|
/*
|
|
* CUSTOM VALUES FOR LPS331AP SENSOR
|
|
* See LPS331AP datasheet:
|
|
* http://www2.st.com/resource/en/datasheet/lps331ap.pdf
|
|
*/
|
|
.wai = 0xbb,
|
|
.wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS,
|
|
.sensors_supported = {
|
|
[0] = LPS331AP_PRESS_DEV_NAME,
|
|
},
|
|
.ch = (struct iio_chan_spec *)st_press_1_channels,
|
|
.num_ch = ARRAY_SIZE(st_press_1_channels),
|
|
.odr = {
|
|
.addr = 0x20,
|
|
.mask = 0x70,
|
|
.odr_avl = {
|
|
{ .hz = 1, .value = 0x01 },
|
|
{ .hz = 7, .value = 0x05 },
|
|
{ .hz = 13, .value = 0x06 },
|
|
{ .hz = 25, .value = 0x07 },
|
|
},
|
|
},
|
|
.pw = {
|
|
.addr = 0x20,
|
|
.mask = 0x80,
|
|
.value_on = ST_SENSORS_DEFAULT_POWER_ON_VALUE,
|
|
.value_off = ST_SENSORS_DEFAULT_POWER_OFF_VALUE,
|
|
},
|
|
.fs = {
|
|
.addr = 0x23,
|
|
.mask = 0x30,
|
|
.fs_avl = {
|
|
/*
|
|
* Pressure and temperature sensitivity values
|
|
* as defined in table 3 of LPS331AP datasheet.
|
|
*/
|
|
[0] = {
|
|
.num = ST_PRESS_FS_AVL_1260MB,
|
|
.gain = ST_PRESS_KPASCAL_NANO_SCALE,
|
|
.gain2 = ST_PRESS_LSB_PER_CELSIUS,
|
|
},
|
|
},
|
|
},
|
|
.bdu = {
|
|
.addr = 0x20,
|
|
.mask = 0x04,
|
|
},
|
|
.drdy_irq = {
|
|
.int1 = {
|
|
.addr = 0x22,
|
|
.mask = 0x04,
|
|
.addr_od = 0x22,
|
|
.mask_od = 0x40,
|
|
},
|
|
.int2 = {
|
|
.addr = 0x22,
|
|
.mask = 0x20,
|
|
.addr_od = 0x22,
|
|
.mask_od = 0x40,
|
|
},
|
|
.addr_ihl = 0x22,
|
|
.mask_ihl = 0x80,
|
|
.stat_drdy = {
|
|
.addr = ST_SENSORS_DEFAULT_STAT_ADDR,
|
|
.mask = 0x03,
|
|
},
|
|
},
|
|
.sim = {
|
|
.addr = 0x20,
|
|
.value = BIT(0),
|
|
},
|
|
.multi_read_bit = true,
|
|
.bootime = 2,
|
|
},
|
|
{
|
|
/*
|
|
* CUSTOM VALUES FOR LPS001WP SENSOR
|
|
*/
|
|
.wai = 0xba,
|
|
.wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS,
|
|
.sensors_supported = {
|
|
[0] = LPS001WP_PRESS_DEV_NAME,
|
|
},
|
|
.ch = (struct iio_chan_spec *)st_press_lps001wp_channels,
|
|
.num_ch = ARRAY_SIZE(st_press_lps001wp_channels),
|
|
.odr = {
|
|
.addr = 0x20,
|
|
.mask = 0x30,
|
|
.odr_avl = {
|
|
{ .hz = 1, .value = 0x01 },
|
|
{ .hz = 7, .value = 0x02 },
|
|
{ .hz = 13, .value = 0x03 },
|
|
},
|
|
},
|
|
.pw = {
|
|
.addr = 0x20,
|
|
.mask = 0x40,
|
|
.value_on = ST_SENSORS_DEFAULT_POWER_ON_VALUE,
|
|
.value_off = ST_SENSORS_DEFAULT_POWER_OFF_VALUE,
|
|
},
|
|
.fs = {
|
|
.fs_avl = {
|
|
/*
|
|
* Pressure and temperature resolution values
|
|
* as defined in table 3 of LPS001WP datasheet.
|
|
*/
|
|
[0] = {
|
|
.num = ST_PRESS_FS_AVL_1100MB,
|
|
.gain = ST_PRESS_LPS001WP_FS_AVL_PRESS_GAIN,
|
|
.gain2 = ST_PRESS_LPS001WP_LSB_PER_CELSIUS,
|
|
},
|
|
},
|
|
},
|
|
.bdu = {
|
|
.addr = 0x20,
|
|
.mask = 0x04,
|
|
},
|
|
.sim = {
|
|
.addr = 0x20,
|
|
.value = BIT(0),
|
|
},
|
|
.multi_read_bit = true,
|
|
.bootime = 2,
|
|
},
|
|
{
|
|
/*
|
|
* CUSTOM VALUES FOR LPS25H SENSOR
|
|
* See LPS25H datasheet:
|
|
* http://www2.st.com/resource/en/datasheet/lps25h.pdf
|
|
*/
|
|
.wai = 0xbd,
|
|
.wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS,
|
|
.sensors_supported = {
|
|
[0] = LPS25H_PRESS_DEV_NAME,
|
|
},
|
|
.ch = (struct iio_chan_spec *)st_press_1_channels,
|
|
.num_ch = ARRAY_SIZE(st_press_1_channels),
|
|
.odr = {
|
|
.addr = 0x20,
|
|
.mask = 0x70,
|
|
.odr_avl = {
|
|
{ .hz = 1, .value = 0x01 },
|
|
{ .hz = 7, .value = 0x02 },
|
|
{ .hz = 13, .value = 0x03 },
|
|
{ .hz = 25, .value = 0x04 },
|
|
},
|
|
},
|
|
.pw = {
|
|
.addr = 0x20,
|
|
.mask = 0x80,
|
|
.value_on = ST_SENSORS_DEFAULT_POWER_ON_VALUE,
|
|
.value_off = ST_SENSORS_DEFAULT_POWER_OFF_VALUE,
|
|
},
|
|
.fs = {
|
|
.fs_avl = {
|
|
/*
|
|
* Pressure and temperature sensitivity values
|
|
* as defined in table 3 of LPS25H datasheet.
|
|
*/
|
|
[0] = {
|
|
.num = ST_PRESS_FS_AVL_1260MB,
|
|
.gain = ST_PRESS_KPASCAL_NANO_SCALE,
|
|
.gain2 = ST_PRESS_LSB_PER_CELSIUS,
|
|
},
|
|
},
|
|
},
|
|
.bdu = {
|
|
.addr = 0x20,
|
|
.mask = 0x04,
|
|
},
|
|
.drdy_irq = {
|
|
.int1 = {
|
|
.addr = 0x23,
|
|
.mask = 0x01,
|
|
.addr_od = 0x22,
|
|
.mask_od = 0x40,
|
|
},
|
|
.addr_ihl = 0x22,
|
|
.mask_ihl = 0x80,
|
|
.stat_drdy = {
|
|
.addr = ST_SENSORS_DEFAULT_STAT_ADDR,
|
|
.mask = 0x03,
|
|
},
|
|
},
|
|
.sim = {
|
|
.addr = 0x20,
|
|
.value = BIT(0),
|
|
},
|
|
.multi_read_bit = true,
|
|
.bootime = 2,
|
|
},
|
|
{
|
|
/*
|
|
* CUSTOM VALUES FOR LPS22HB SENSOR
|
|
* See LPS22HB datasheet:
|
|
* http://www2.st.com/resource/en/datasheet/lps22hb.pdf
|
|
*/
|
|
.wai = 0xb1,
|
|
.wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS,
|
|
.sensors_supported = {
|
|
[0] = LPS22HB_PRESS_DEV_NAME,
|
|
[1] = LPS33HW_PRESS_DEV_NAME,
|
|
[2] = LPS35HW_PRESS_DEV_NAME,
|
|
},
|
|
.ch = (struct iio_chan_spec *)st_press_lps22hb_channels,
|
|
.num_ch = ARRAY_SIZE(st_press_lps22hb_channels),
|
|
.odr = {
|
|
.addr = 0x10,
|
|
.mask = 0x70,
|
|
.odr_avl = {
|
|
{ .hz = 1, .value = 0x01 },
|
|
{ .hz = 10, .value = 0x02 },
|
|
{ .hz = 25, .value = 0x03 },
|
|
{ .hz = 50, .value = 0x04 },
|
|
{ .hz = 75, .value = 0x05 },
|
|
},
|
|
},
|
|
.pw = {
|
|
.addr = 0x10,
|
|
.mask = 0x70,
|
|
.value_off = ST_SENSORS_DEFAULT_POWER_OFF_VALUE,
|
|
},
|
|
.fs = {
|
|
.fs_avl = {
|
|
/*
|
|
* Pressure and temperature sensitivity values
|
|
* as defined in table 3 of LPS22HB datasheet.
|
|
*/
|
|
[0] = {
|
|
.num = ST_PRESS_FS_AVL_1260MB,
|
|
.gain = ST_PRESS_KPASCAL_NANO_SCALE,
|
|
.gain2 = ST_PRESS_LPS22HB_LSB_PER_CELSIUS,
|
|
},
|
|
},
|
|
},
|
|
.bdu = {
|
|
.addr = 0x10,
|
|
.mask = 0x02,
|
|
},
|
|
.drdy_irq = {
|
|
.int1 = {
|
|
.addr = 0x12,
|
|
.mask = 0x04,
|
|
.addr_od = 0x12,
|
|
.mask_od = 0x40,
|
|
},
|
|
.addr_ihl = 0x12,
|
|
.mask_ihl = 0x80,
|
|
.stat_drdy = {
|
|
.addr = ST_SENSORS_DEFAULT_STAT_ADDR,
|
|
.mask = 0x03,
|
|
},
|
|
},
|
|
.sim = {
|
|
.addr = 0x10,
|
|
.value = BIT(0),
|
|
},
|
|
.multi_read_bit = false,
|
|
.bootime = 2,
|
|
},
|
|
{
|
|
/*
|
|
* CUSTOM VALUES FOR LPS22HH SENSOR
|
|
* See LPS22HH datasheet:
|
|
* http://www2.st.com/resource/en/datasheet/lps22hh.pdf
|
|
*/
|
|
.wai = 0xb3,
|
|
.wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS,
|
|
.sensors_supported = {
|
|
[0] = LPS22HH_PRESS_DEV_NAME,
|
|
},
|
|
.ch = (struct iio_chan_spec *)st_press_lps22hb_channels,
|
|
.num_ch = ARRAY_SIZE(st_press_lps22hb_channels),
|
|
.odr = {
|
|
.addr = 0x10,
|
|
.mask = 0x70,
|
|
.odr_avl = {
|
|
{ .hz = 1, .value = 0x01 },
|
|
{ .hz = 10, .value = 0x02 },
|
|
{ .hz = 25, .value = 0x03 },
|
|
{ .hz = 50, .value = 0x04 },
|
|
{ .hz = 75, .value = 0x05 },
|
|
{ .hz = 100, .value = 0x06 },
|
|
{ .hz = 200, .value = 0x07 },
|
|
},
|
|
},
|
|
.pw = {
|
|
.addr = 0x10,
|
|
.mask = 0x70,
|
|
.value_off = ST_SENSORS_DEFAULT_POWER_OFF_VALUE,
|
|
},
|
|
.fs = {
|
|
.fs_avl = {
|
|
/*
|
|
* Pressure and temperature sensitivity values
|
|
* as defined in table 3 of LPS22HH datasheet.
|
|
*/
|
|
[0] = {
|
|
.num = ST_PRESS_FS_AVL_1260MB,
|
|
.gain = ST_PRESS_KPASCAL_NANO_SCALE,
|
|
.gain2 = ST_PRESS_LPS22HB_LSB_PER_CELSIUS,
|
|
},
|
|
},
|
|
},
|
|
.bdu = {
|
|
.addr = 0x10,
|
|
.mask = BIT(1),
|
|
},
|
|
.drdy_irq = {
|
|
.int1 = {
|
|
.addr = 0x12,
|
|
.mask = BIT(2),
|
|
.addr_od = 0x11,
|
|
.mask_od = BIT(5),
|
|
},
|
|
.addr_ihl = 0x11,
|
|
.mask_ihl = BIT(6),
|
|
.stat_drdy = {
|
|
.addr = ST_SENSORS_DEFAULT_STAT_ADDR,
|
|
.mask = 0x03,
|
|
},
|
|
},
|
|
.sim = {
|
|
.addr = 0x10,
|
|
.value = BIT(0),
|
|
},
|
|
.multi_read_bit = false,
|
|
.bootime = 2,
|
|
},
|
|
};
|
|
|
|
static int st_press_write_raw(struct iio_dev *indio_dev,
|
|
struct iio_chan_spec const *ch,
|
|
int val,
|
|
int val2,
|
|
long mask)
|
|
{
|
|
switch (mask) {
|
|
case IIO_CHAN_INFO_SAMP_FREQ:
|
|
if (val2)
|
|
return -EINVAL;
|
|
|
|
return st_sensors_set_odr(indio_dev, val);
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
static int st_press_read_raw(struct iio_dev *indio_dev,
|
|
struct iio_chan_spec const *ch, int *val,
|
|
int *val2, long mask)
|
|
{
|
|
int err;
|
|
struct st_sensor_data *press_data = iio_priv(indio_dev);
|
|
|
|
switch (mask) {
|
|
case IIO_CHAN_INFO_RAW:
|
|
err = st_sensors_read_info_raw(indio_dev, ch, val);
|
|
if (err < 0)
|
|
goto read_error;
|
|
|
|
return IIO_VAL_INT;
|
|
case IIO_CHAN_INFO_SCALE:
|
|
switch (ch->type) {
|
|
case IIO_PRESSURE:
|
|
*val = 0;
|
|
*val2 = press_data->current_fullscale->gain;
|
|
return IIO_VAL_INT_PLUS_NANO;
|
|
case IIO_TEMP:
|
|
*val = MCELSIUS_PER_CELSIUS;
|
|
*val2 = press_data->current_fullscale->gain2;
|
|
return IIO_VAL_FRACTIONAL;
|
|
default:
|
|
err = -EINVAL;
|
|
goto read_error;
|
|
}
|
|
|
|
case IIO_CHAN_INFO_OFFSET:
|
|
switch (ch->type) {
|
|
case IIO_TEMP:
|
|
*val = ST_PRESS_MILLI_CELSIUS_OFFSET *
|
|
press_data->current_fullscale->gain2;
|
|
*val2 = MCELSIUS_PER_CELSIUS;
|
|
break;
|
|
default:
|
|
err = -EINVAL;
|
|
goto read_error;
|
|
}
|
|
|
|
return IIO_VAL_FRACTIONAL;
|
|
case IIO_CHAN_INFO_SAMP_FREQ:
|
|
*val = press_data->odr;
|
|
return IIO_VAL_INT;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
read_error:
|
|
return err;
|
|
}
|
|
|
|
static ST_SENSORS_DEV_ATTR_SAMP_FREQ_AVAIL();
|
|
|
|
static struct attribute *st_press_attributes[] = {
|
|
&iio_dev_attr_sampling_frequency_available.dev_attr.attr,
|
|
NULL,
|
|
};
|
|
|
|
static const struct attribute_group st_press_attribute_group = {
|
|
.attrs = st_press_attributes,
|
|
};
|
|
|
|
static const struct iio_info press_info = {
|
|
.attrs = &st_press_attribute_group,
|
|
.read_raw = &st_press_read_raw,
|
|
.write_raw = &st_press_write_raw,
|
|
.debugfs_reg_access = &st_sensors_debugfs_reg_access,
|
|
};
|
|
|
|
#ifdef CONFIG_IIO_TRIGGER
|
|
static const struct iio_trigger_ops st_press_trigger_ops = {
|
|
.set_trigger_state = ST_PRESS_TRIGGER_SET_STATE,
|
|
.validate_device = st_sensors_validate_device,
|
|
};
|
|
#define ST_PRESS_TRIGGER_OPS (&st_press_trigger_ops)
|
|
#else
|
|
#define ST_PRESS_TRIGGER_OPS NULL
|
|
#endif
|
|
|
|
/*
|
|
* st_press_get_settings() - get sensor settings from device name
|
|
* @name: device name buffer reference.
|
|
*
|
|
* Return: valid reference on success, NULL otherwise.
|
|
*/
|
|
const struct st_sensor_settings *st_press_get_settings(const char *name)
|
|
{
|
|
int index = st_sensors_get_settings_index(name,
|
|
st_press_sensors_settings,
|
|
ARRAY_SIZE(st_press_sensors_settings));
|
|
if (index < 0)
|
|
return NULL;
|
|
|
|
return &st_press_sensors_settings[index];
|
|
}
|
|
EXPORT_SYMBOL_NS(st_press_get_settings, IIO_ST_SENSORS);
|
|
|
|
int st_press_common_probe(struct iio_dev *indio_dev)
|
|
{
|
|
struct st_sensor_data *press_data = iio_priv(indio_dev);
|
|
struct device *parent = indio_dev->dev.parent;
|
|
struct st_sensors_platform_data *pdata = dev_get_platdata(parent);
|
|
int err;
|
|
|
|
indio_dev->modes = INDIO_DIRECT_MODE;
|
|
indio_dev->info = &press_info;
|
|
|
|
err = st_sensors_verify_id(indio_dev);
|
|
if (err < 0)
|
|
return err;
|
|
|
|
/*
|
|
* Skip timestamping channel while declaring available channels to
|
|
* common st_sensor layer. Look at st_sensors_get_buffer_element() to
|
|
* see how timestamps are explicitly pushed as last samples block
|
|
* element.
|
|
*/
|
|
press_data->num_data_channels = press_data->sensor_settings->num_ch - 1;
|
|
indio_dev->channels = press_data->sensor_settings->ch;
|
|
indio_dev->num_channels = press_data->sensor_settings->num_ch;
|
|
|
|
press_data->current_fullscale = &press_data->sensor_settings->fs.fs_avl[0];
|
|
|
|
press_data->odr = press_data->sensor_settings->odr.odr_avl[0].hz;
|
|
|
|
/* Some devices don't support a data ready pin. */
|
|
if (!pdata && (press_data->sensor_settings->drdy_irq.int1.addr ||
|
|
press_data->sensor_settings->drdy_irq.int2.addr))
|
|
pdata = (struct st_sensors_platform_data *)&default_press_pdata;
|
|
|
|
err = st_sensors_init_sensor(indio_dev, pdata);
|
|
if (err < 0)
|
|
return err;
|
|
|
|
err = st_press_allocate_ring(indio_dev);
|
|
if (err < 0)
|
|
return err;
|
|
|
|
if (press_data->irq > 0) {
|
|
err = st_sensors_allocate_trigger(indio_dev,
|
|
ST_PRESS_TRIGGER_OPS);
|
|
if (err < 0)
|
|
return err;
|
|
}
|
|
|
|
return devm_iio_device_register(parent, indio_dev);
|
|
}
|
|
EXPORT_SYMBOL_NS(st_press_common_probe, IIO_ST_SENSORS);
|
|
|
|
MODULE_AUTHOR("Denis Ciocca <denis.ciocca@st.com>");
|
|
MODULE_DESCRIPTION("STMicroelectronics pressures driver");
|
|
MODULE_LICENSE("GPL v2");
|
|
MODULE_IMPORT_NS(IIO_ST_SENSORS);
|