142 строки
3.2 KiB
C
142 строки
3.2 KiB
C
/*
|
|
* Copyright (c) 2015, The Linux Foundation. All rights reserved.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 and
|
|
* only version 2 as published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
*/
|
|
|
|
#include <linux/err.h>
|
|
#include <linux/io.h>
|
|
#include <linux/nvmem-consumer.h>
|
|
#include <linux/of_address.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/regmap.h>
|
|
#include "tsens.h"
|
|
|
|
#define S0_ST_ADDR 0x1030
|
|
#define SN_ADDR_OFFSET 0x4
|
|
#define SN_ST_TEMP_MASK 0x3ff
|
|
#define CAL_DEGC_PT1 30
|
|
#define CAL_DEGC_PT2 120
|
|
#define SLOPE_FACTOR 1000
|
|
#define SLOPE_DEFAULT 3200
|
|
|
|
char *qfprom_read(struct device *dev, const char *cname)
|
|
{
|
|
struct nvmem_cell *cell;
|
|
ssize_t data;
|
|
char *ret;
|
|
|
|
cell = nvmem_cell_get(dev, cname);
|
|
if (IS_ERR(cell))
|
|
return ERR_CAST(cell);
|
|
|
|
ret = nvmem_cell_read(cell, &data);
|
|
nvmem_cell_put(cell);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* Use this function on devices where slope and offset calculations
|
|
* depend on calibration data read from qfprom. On others the slope
|
|
* and offset values are derived from tz->tzp->slope and tz->tzp->offset
|
|
* resp.
|
|
*/
|
|
void compute_intercept_slope(struct tsens_device *tmdev, u32 *p1,
|
|
u32 *p2, u32 mode)
|
|
{
|
|
int i;
|
|
int num, den;
|
|
|
|
for (i = 0; i < tmdev->num_sensors; i++) {
|
|
dev_dbg(tmdev->dev,
|
|
"sensor%d - data_point1:%#x data_point2:%#x\n",
|
|
i, p1[i], p2[i]);
|
|
|
|
tmdev->sensor[i].slope = SLOPE_DEFAULT;
|
|
if (mode == TWO_PT_CALIB) {
|
|
/*
|
|
* slope (m) = adc_code2 - adc_code1 (y2 - y1)/
|
|
* temp_120_degc - temp_30_degc (x2 - x1)
|
|
*/
|
|
num = p2[i] - p1[i];
|
|
num *= SLOPE_FACTOR;
|
|
den = CAL_DEGC_PT2 - CAL_DEGC_PT1;
|
|
tmdev->sensor[i].slope = num / den;
|
|
}
|
|
|
|
tmdev->sensor[i].offset = (p1[i] * SLOPE_FACTOR) -
|
|
(CAL_DEGC_PT1 *
|
|
tmdev->sensor[i].slope);
|
|
dev_dbg(tmdev->dev, "offset:%d\n", tmdev->sensor[i].offset);
|
|
}
|
|
}
|
|
|
|
static inline int code_to_degc(u32 adc_code, const struct tsens_sensor *s)
|
|
{
|
|
int degc, num, den;
|
|
|
|
num = (adc_code * SLOPE_FACTOR) - s->offset;
|
|
den = s->slope;
|
|
|
|
if (num > 0)
|
|
degc = num + (den / 2);
|
|
else if (num < 0)
|
|
degc = num - (den / 2);
|
|
else
|
|
degc = num;
|
|
|
|
degc /= den;
|
|
|
|
return degc;
|
|
}
|
|
|
|
int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
|
|
{
|
|
struct tsens_sensor *s = &tmdev->sensor[id];
|
|
u32 code;
|
|
unsigned int sensor_addr;
|
|
int last_temp = 0, ret;
|
|
|
|
sensor_addr = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
|
|
ret = regmap_read(tmdev->map, sensor_addr, &code);
|
|
if (ret)
|
|
return ret;
|
|
last_temp = code & SN_ST_TEMP_MASK;
|
|
|
|
*temp = code_to_degc(last_temp, s) * 1000;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct regmap_config tsens_config = {
|
|
.reg_bits = 32,
|
|
.val_bits = 32,
|
|
.reg_stride = 4,
|
|
};
|
|
|
|
int __init init_common(struct tsens_device *tmdev)
|
|
{
|
|
void __iomem *base;
|
|
|
|
base = of_iomap(tmdev->dev->of_node, 0);
|
|
if (!base)
|
|
return -EINVAL;
|
|
|
|
tmdev->map = devm_regmap_init_mmio(tmdev->dev, base, &tsens_config);
|
|
if (IS_ERR(tmdev->map)) {
|
|
iounmap(base);
|
|
return PTR_ERR(tmdev->map);
|
|
}
|
|
|
|
return 0;
|
|
}
|