WSL2-Linux-Kernel/arch/sh64/Kconfig

296 строки
4.8 KiB
Plaintext

#
# For a description of the syntax of this configuration file,
# see Documentation/kbuild/kconfig-language.txt.
#
mainmenu "Linux/SH64 Kernel Configuration"
config SUPERH
bool
default y
config SUPERH64
bool
default y
config MMU
bool
default y
config QUICKLIST
def_bool y
config RWSEM_GENERIC_SPINLOCK
bool
default y
config GENERIC_FIND_NEXT_BIT
bool
default y
config GENERIC_HWEIGHT
bool
default y
config GENERIC_CALIBRATE_DELAY
bool
default y
config GENERIC_HARDIRQS
bool
default y
config GENERIC_IRQ_PROBE
bool
default y
config RWSEM_XCHGADD_ALGORITHM
bool
config ARCH_HAS_ILOG2_U32
bool
default n
config ARCH_HAS_ILOG2_U64
bool
default n
config ARCH_NO_VIRT_TO_BUS
def_bool y
source init/Kconfig
menu "System type"
choice
prompt "SuperH system type"
default SH_SIMULATOR
config SH_SIMULATOR
bool "Simulator"
config SH_CAYMAN
bool "Cayman"
config SH_HARP
bool "ST50-Harp"
endchoice
choice
prompt "Processor family"
default CPU_SH5
config CPU_SH5
bool "SH-5"
endchoice
choice
prompt "Processor type"
config CPU_SUBTYPE_SH5_101
bool "SH5-101"
depends on CPU_SH5
config CPU_SUBTYPE_SH5_103
bool "SH5-103"
depends on CPU_SH5
endchoice
choice
prompt "Endianness"
default LITTLE_ENDIAN
config LITTLE_ENDIAN
bool "Little-Endian"
config BIG_ENDIAN
bool "Big-Endian"
endchoice
config SH_FPU
bool "FPU support"
default y
config SH64_FPU_DENORM_FLUSH
depends on SH_FPU
bool "Flush floating point denorms to zero"
choice
prompt "Page table levels"
default SH64_PGTABLE_2_LEVEL
config SH64_PGTABLE_2_LEVEL
bool "2"
config SH64_PGTABLE_3_LEVEL
bool "3"
endchoice
choice
prompt "HugeTLB page size"
depends on HUGETLB_PAGE && MMU
default HUGETLB_PAGE_SIZE_64K
config HUGETLB_PAGE_SIZE_64K
bool "64K"
config HUGETLB_PAGE_SIZE_1MB
bool "1MB"
config HUGETLB_PAGE_SIZE_512MB
bool "512MB"
endchoice
config SH64_USER_MISALIGNED_FIXUP
bool "Fixup misaligned loads/stores occurring in user mode"
comment "Memory options"
config CACHED_MEMORY_OFFSET
hex "Cached Area Offset"
default "20000000"
config MEMORY_START
hex "Physical memory start address"
default "80000000"
config MEMORY_SIZE_IN_MB
int "Memory size (in MB)"
default "8" if SH_SIMULATOR
default "64"
comment "Cache options"
choice
prompt "DCache mode"
default DCACHE_DISABLED if SH_SIMULATOR
default DCACHE_WRITE_BACK
config DCACHE_WRITE_BACK
bool "Write-back"
depends on !SH_SIMULATOR
config DCACHE_WRITE_THROUGH
bool "Write-through"
depends on !SH_SIMULATOR
config DCACHE_DISABLED
bool "Disabled"
endchoice
config ICACHE_DISABLED
bool "ICache Disabling"
config PCIDEVICE_MEMORY_START
hex
default "C0000000"
config DEVICE_MEMORY_START
hex
default "E0000000"
config FLASH_MEMORY_START
hex "Flash memory/on-chip devices start address"
default "00000000"
config PCI_BLOCK_START
hex "PCI block start address"
default "40000000"
comment "CPU Subtype specific options"
config SH64_ID2815_WORKAROUND
bool "Include workaround for SH5-101 cut2 silicon defect ID2815"
comment "Misc options"
config HEARTBEAT
bool "Heartbeat LED"
depends on SH_CAYMAN
config HDSP253_LED
bool "Support for HDSP-253 LED"
depends on SH_CAYMAN
config SH_DMA
tristate "DMA controller (DMAC) support"
config PREEMPT
bool "Preemptible Kernel (EXPERIMENTAL)"
depends on EXPERIMENTAL
source "mm/Kconfig"
endmenu
menu "Bus options (PCI, PCMCIA, EISA, MCA, ISA)"
config ISA
bool
config SBUS
bool
config PCI
bool "PCI support"
depends on SH_CAYMAN
help
Find out whether you have a PCI motherboard. PCI is the name of a
bus system, i.e. the way the CPU talks to the other stuff inside
your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
VESA. If you have PCI, say Y, otherwise N.
The PCI-HOWTO, available from
<http://www.tldp.org/docs.html#howto>, contains valuable
information about which PCI hardware does work under Linux and which
doesn't.
config SH_PCIDMA_NONCOHERENT
bool "Cache and PCI noncoherent"
depends on PCI
default y
help
Enable this option if your platform does not have a CPU cache which
remains coherent with PCI DMA. It is safest to say 'Y', although you
will see better performance if you can say 'N', because the PCI DMA
code will not have to flush the CPU's caches. If you have a PCI host
bridge integrated with your SH CPU, refer carefully to the chip specs
to see if you can say 'N' here. Otherwise, leave it as 'Y'.
source "drivers/pci/Kconfig"
source "drivers/pcmcia/Kconfig"
source "drivers/pci/hotplug/Kconfig"
endmenu
menu "Executable file formats"
source "fs/Kconfig.binfmt"
endmenu
source "net/Kconfig"
source "drivers/Kconfig"
source "fs/Kconfig"
source "kernel/Kconfig.instrumentation"
source "arch/sh64/Kconfig.debug"
source "security/Kconfig"
source "crypto/Kconfig"
source "lib/Kconfig"