WSL2-Linux-Kernel/drivers/usb/host/isp1760-hcd.h

228 строки
5.9 KiB
C

#ifndef _ISP1760_HCD_H_
#define _ISP1760_HCD_H_
/* exports for if */
struct usb_hcd *isp1760_register(phys_addr_t res_start, resource_size_t res_len,
int irq, unsigned long irqflags,
struct device *dev, const char *busname,
unsigned int devflags);
int init_kmem_once(void);
void deinit_kmem_cache(void);
/* EHCI capability registers */
#define HC_CAPLENGTH 0x00
#define HC_HCSPARAMS 0x04
#define HC_HCCPARAMS 0x08
/* EHCI operational registers */
#define HC_USBCMD 0x20
#define HC_USBSTS 0x24
#define HC_FRINDEX 0x2c
#define HC_CONFIGFLAG 0x60
#define HC_PORTSC1 0x64
#define HC_ISO_PTD_DONEMAP_REG 0x130
#define HC_ISO_PTD_SKIPMAP_REG 0x134
#define HC_ISO_PTD_LASTPTD_REG 0x138
#define HC_INT_PTD_DONEMAP_REG 0x140
#define HC_INT_PTD_SKIPMAP_REG 0x144
#define HC_INT_PTD_LASTPTD_REG 0x148
#define HC_ATL_PTD_DONEMAP_REG 0x150
#define HC_ATL_PTD_SKIPMAP_REG 0x154
#define HC_ATL_PTD_LASTPTD_REG 0x158
/* Configuration Register */
#define HC_HW_MODE_CTRL 0x300
#define ALL_ATX_RESET (1 << 31)
#define HW_ANA_DIGI_OC (1 << 15)
#define HW_DATA_BUS_32BIT (1 << 8)
#define HW_DACK_POL_HIGH (1 << 6)
#define HW_DREQ_POL_HIGH (1 << 5)
#define HW_INTR_HIGH_ACT (1 << 2)
#define HW_INTR_EDGE_TRIG (1 << 1)
#define HW_GLOBAL_INTR_EN (1 << 0)
#define HC_CHIP_ID_REG 0x304
#define HC_SCRATCH_REG 0x308
#define HC_RESET_REG 0x30c
#define SW_RESET_RESET_HC (1 << 1)
#define SW_RESET_RESET_ALL (1 << 0)
#define HC_BUFFER_STATUS_REG 0x334
#define ATL_BUFFER 0x1
#define INT_BUFFER 0x2
#define ISO_BUFFER 0x4
#define BUFFER_MAP 0x7
#define HC_MEMORY_REG 0x33c
#define ISP_BANK(x) ((x) << 16)
#define HC_PORT1_CTRL 0x374
#define PORT1_POWER (3 << 3)
#define PORT1_INIT1 (1 << 7)
#define PORT1_INIT2 (1 << 23)
#define HW_OTG_CTRL_SET 0x374
#define HW_OTG_CTRL_CLR 0x376
/* Interrupt Register */
#define HC_INTERRUPT_REG 0x310
#define HC_INTERRUPT_ENABLE 0x314
#define INTERRUPT_ENABLE_MASK (HC_INTL_INT | HC_ATL_INT | HC_EOT_INT)
#define HC_ISO_INT (1 << 9)
#define HC_ATL_INT (1 << 8)
#define HC_INTL_INT (1 << 7)
#define HC_EOT_INT (1 << 3)
#define HC_SOT_INT (1 << 1)
#define HC_ISO_IRQ_MASK_OR_REG 0x318
#define HC_INT_IRQ_MASK_OR_REG 0x31C
#define HC_ATL_IRQ_MASK_OR_REG 0x320
#define HC_ISO_IRQ_MASK_AND_REG 0x324
#define HC_INT_IRQ_MASK_AND_REG 0x328
#define HC_ATL_IRQ_MASK_AND_REG 0x32C
/* Register sets */
#define HC_BEGIN_OF_ATL 0x0c00
#define HC_BEGIN_OF_INT 0x0800
#define HC_BEGIN_OF_ISO 0x0400
#define HC_BEGIN_OF_PAYLOAD 0x1000
/* urb state*/
#define DELETE_URB (0x0008)
#define NO_TRANSFER_ACTIVE (0xffffffff)
#define ATL_REGS_OFFSET (0xc00)
#define INT_REGS_OFFSET (0x800)
/* Philips Transfer Descriptor (PTD) */
struct ptd {
__le32 dw0;
__le32 dw1;
__le32 dw2;
__le32 dw3;
__le32 dw4;
__le32 dw5;
__le32 dw6;
__le32 dw7;
};
struct inter_packet_info {
void *data_buffer;
u32 payload;
#define PTD_FIRE_NEXT (1 << 0)
#define PTD_URB_FINISHED (1 << 1)
struct urb *urb;
struct isp1760_qh *qh;
struct isp1760_qtd *qtd;
};
typedef void (packet_enqueue)(struct usb_hcd *hcd, struct isp1760_qh *qh,
struct isp1760_qtd *qtd);
#define isp1760_dbg(priv, fmt, args...) \
dev_dbg(priv_to_hcd(priv)->self.controller, fmt, ##args)
#define isp1760_info(priv, fmt, args...) \
dev_info(priv_to_hcd(priv)->self.controller, fmt, ##args)
#define isp1760_err(priv, fmt, args...) \
dev_err(priv_to_hcd(priv)->self.controller, fmt, ##args)
/*
* Device flags that can vary from board to board. All of these
* indicate the most "atypical" case, so that a devflags of 0 is
* a sane default configuration.
*/
#define ISP1760_FLAG_BUS_WIDTH_16 0x00000002 /* 16-bit data bus width */
#define ISP1760_FLAG_OTG_EN 0x00000004 /* Port 1 supports OTG */
#define ISP1760_FLAG_ANALOG_OC 0x00000008 /* Analog overcurrent */
#define ISP1760_FLAG_DACK_POL_HIGH 0x00000010 /* DACK active high */
#define ISP1760_FLAG_DREQ_POL_HIGH 0x00000020 /* DREQ active high */
#define ISP1760_FLAG_ISP1761 0x00000040 /* Chip is ISP1761 */
/* chip memory management */
struct memory_chunk {
unsigned int start;
unsigned int size;
unsigned int free;
};
/*
* 60kb divided in:
* - 32 blocks @ 256 bytes
* - 20 blocks @ 1024 bytes
* - 4 blocks @ 8192 bytes
*/
#define BLOCK_1_NUM 32
#define BLOCK_2_NUM 20
#define BLOCK_3_NUM 4
#define BLOCK_1_SIZE 256
#define BLOCK_2_SIZE 1024
#define BLOCK_3_SIZE 8192
#define BLOCKS (BLOCK_1_NUM + BLOCK_2_NUM + BLOCK_3_NUM)
#define PAYLOAD_SIZE 0xf000
/* I saw if some reloads if the pointer was negative */
#define ISP1760_NULL_POINTER (0x400)
/* ATL */
/* DW0 */
#define PTD_VALID 1
#define PTD_LENGTH(x) (((u32) x) << 3)
#define PTD_MAXPACKET(x) (((u32) x) << 18)
#define PTD_MULTI(x) (((u32) x) << 29)
#define PTD_ENDPOINT(x) (((u32) x) << 31)
/* DW1 */
#define PTD_DEVICE_ADDR(x) (((u32) x) << 3)
#define PTD_PID_TOKEN(x) (((u32) x) << 10)
#define PTD_TRANS_BULK ((u32) 2 << 12)
#define PTD_TRANS_INT ((u32) 3 << 12)
#define PTD_TRANS_SPLIT ((u32) 1 << 14)
#define PTD_SE_USB_LOSPEED ((u32) 2 << 16)
#define PTD_PORT_NUM(x) (((u32) x) << 18)
#define PTD_HUB_NUM(x) (((u32) x) << 25)
#define PTD_PING(x) (((u32) x) << 26)
/* DW2 */
#define PTD_RL_CNT(x) (((u32) x) << 25)
#define PTD_DATA_START_ADDR(x) (((u32) x) << 8)
#define BASE_ADDR 0x1000
/* DW3 */
#define PTD_CERR(x) (((u32) x) << 23)
#define PTD_NAC_CNT(x) (((u32) x) << 19)
#define PTD_ACTIVE ((u32) 1 << 31)
#define PTD_DATA_TOGGLE(x) (((u32) x) << 25)
#define DW3_HALT_BIT (1 << 30)
#define DW3_ERROR_BIT (1 << 28)
#define DW3_QTD_ACTIVE (1 << 31)
#define INT_UNDERRUN (1 << 2)
#define INT_BABBLE (1 << 1)
#define INT_EXACT (1 << 0)
#define DW1_GET_PID(x) (((x) >> 10) & 0x3)
#define PTD_XFERRED_LENGTH(x) ((x) & 0x7fff)
#define PTD_XFERRED_LENGTH_LO(x) ((x) & 0x7ff)
#define SETUP_PID (2)
#define IN_PID (1)
#define OUT_PID (0)
#define GET_QTD_TOKEN_TYPE(x) ((x) & 0x3)
#define DATA_TOGGLE (1 << 31)
#define GET_DATA_TOGGLE(x) ((x) >> 31)
/* Errata 1 */
#define RL_COUNTER (0)
#define NAK_COUNTER (0)
#define ERR_COUNTER (2)
#define HC_ATL_PL_SIZE (8192)
#endif