494 строки
13 KiB
C
494 строки
13 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* pata_serverworks.c - Serverworks PATA for new ATA layer
|
|
* (C) 2005 Red Hat Inc
|
|
* (C) 2010 Bartlomiej Zolnierkiewicz
|
|
*
|
|
* based upon
|
|
*
|
|
* serverworks.c
|
|
*
|
|
* Copyright (C) 1998-2000 Michel Aubry
|
|
* Copyright (C) 1998-2000 Andrzej Krzysztofowicz
|
|
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
|
|
* Portions copyright (c) 2001 Sun Microsystems
|
|
*
|
|
*
|
|
* RCC/ServerWorks IDE driver for Linux
|
|
*
|
|
* OSB4: `Open South Bridge' IDE Interface (fn 1)
|
|
* supports UDMA mode 2 (33 MB/s)
|
|
*
|
|
* CSB5: `Champion South Bridge' IDE Interface (fn 1)
|
|
* all revisions support UDMA mode 4 (66 MB/s)
|
|
* revision A2.0 and up support UDMA mode 5 (100 MB/s)
|
|
*
|
|
* *** The CSB5 does not provide ANY register ***
|
|
* *** to detect 80-conductor cable presence. ***
|
|
*
|
|
* CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
|
|
*
|
|
* Documentation:
|
|
* Available under NDA only. Errata info very hard to get.
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/blkdev.h>
|
|
#include <linux/delay.h>
|
|
#include <scsi/scsi_host.h>
|
|
#include <linux/libata.h>
|
|
|
|
#define DRV_NAME "pata_serverworks"
|
|
#define DRV_VERSION "0.4.3"
|
|
|
|
#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
|
|
#define SVWKS_CSB6_REVISION 0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
|
|
|
|
/* Seagate Barracuda ATA IV Family drives in UDMA mode 5
|
|
* can overrun their FIFOs when used with the CSB5 */
|
|
|
|
static const char *csb_bad_ata100[] = {
|
|
"ST320011A",
|
|
"ST340016A",
|
|
"ST360021A",
|
|
"ST380021A",
|
|
NULL
|
|
};
|
|
|
|
/**
|
|
* oem_cable - Dell/Sun serverworks cable detection
|
|
* @ap: ATA port to do cable detect
|
|
*
|
|
* Dell PowerEdge and Sun Cobalt 'Alpine' hide the 40/80 pin select
|
|
* for their interfaces in the top two bits of the subsystem ID.
|
|
*/
|
|
|
|
static int oem_cable(struct ata_port *ap)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
|
|
if (pdev->subsystem_device & (1 << (ap->port_no + 14)))
|
|
return ATA_CBL_PATA80;
|
|
return ATA_CBL_PATA40;
|
|
}
|
|
|
|
struct sv_cable_table {
|
|
int device;
|
|
int subvendor;
|
|
int (*cable_detect)(struct ata_port *ap);
|
|
};
|
|
|
|
static struct sv_cable_table cable_detect[] = {
|
|
{ PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_VENDOR_ID_DELL, oem_cable },
|
|
{ PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_VENDOR_ID_DELL, oem_cable },
|
|
{ PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_VENDOR_ID_SUN, oem_cable },
|
|
{ PCI_DEVICE_ID_SERVERWORKS_OSB4IDE, PCI_ANY_ID, ata_cable_40wire },
|
|
{ PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_ANY_ID, ata_cable_unknown },
|
|
{ PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_ANY_ID, ata_cable_unknown },
|
|
{ PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2, PCI_ANY_ID, ata_cable_unknown },
|
|
{ PCI_DEVICE_ID_SERVERWORKS_HT1000IDE, PCI_ANY_ID, ata_cable_unknown },
|
|
{ }
|
|
};
|
|
|
|
/**
|
|
* serverworks_cable_detect - cable detection
|
|
* @ap: ATA port
|
|
*
|
|
* Perform cable detection according to the device and subvendor
|
|
* identifications
|
|
*/
|
|
|
|
static int serverworks_cable_detect(struct ata_port *ap)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
struct sv_cable_table *cb = cable_detect;
|
|
|
|
while(cb->device) {
|
|
if (cb->device == pdev->device &&
|
|
(cb->subvendor == pdev->subsystem_vendor ||
|
|
cb->subvendor == PCI_ANY_ID)) {
|
|
return cb->cable_detect(ap);
|
|
}
|
|
cb++;
|
|
}
|
|
|
|
BUG();
|
|
return -1; /* kill compiler warning */
|
|
}
|
|
|
|
/**
|
|
* serverworks_is_csb - Check for CSB or OSB
|
|
* @pdev: PCI device to check
|
|
*
|
|
* Returns true if the device being checked is known to be a CSB
|
|
* series device.
|
|
*/
|
|
|
|
static u8 serverworks_is_csb(struct pci_dev *pdev)
|
|
{
|
|
switch (pdev->device) {
|
|
case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
|
|
case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
|
|
case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
|
|
case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
|
|
return 1;
|
|
default:
|
|
break;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* serverworks_osb4_filter - mode selection filter
|
|
* @adev: ATA device
|
|
* @mask: Mask of proposed modes
|
|
*
|
|
* Filter the offered modes for the device to apply controller
|
|
* specific rules. OSB4 requires no UDMA for disks due to a FIFO
|
|
* bug we hit.
|
|
*/
|
|
|
|
static unsigned long serverworks_osb4_filter(struct ata_device *adev, unsigned long mask)
|
|
{
|
|
if (adev->class == ATA_DEV_ATA)
|
|
mask &= ~ATA_MASK_UDMA;
|
|
return mask;
|
|
}
|
|
|
|
|
|
/**
|
|
* serverworks_csb_filter - mode selection filter
|
|
* @adev: ATA device
|
|
* @mask: Mask of proposed modes
|
|
*
|
|
* Check the blacklist and disable UDMA5 if matched
|
|
*/
|
|
|
|
static unsigned long serverworks_csb_filter(struct ata_device *adev, unsigned long mask)
|
|
{
|
|
const char *p;
|
|
char model_num[ATA_ID_PROD_LEN + 1];
|
|
int i;
|
|
|
|
/* Disk, UDMA */
|
|
if (adev->class != ATA_DEV_ATA)
|
|
return mask;
|
|
|
|
/* Actually do need to check */
|
|
ata_id_c_string(adev->id, model_num, ATA_ID_PROD, sizeof(model_num));
|
|
|
|
for (i = 0; (p = csb_bad_ata100[i]) != NULL; i++) {
|
|
if (!strcmp(p, model_num))
|
|
mask &= ~(0xE0 << ATA_SHIFT_UDMA);
|
|
}
|
|
return mask;
|
|
}
|
|
|
|
/**
|
|
* serverworks_set_piomode - set initial PIO mode data
|
|
* @ap: ATA interface
|
|
* @adev: ATA device
|
|
*
|
|
* Program the OSB4/CSB5 timing registers for PIO. The PIO register
|
|
* load is done as a simple lookup.
|
|
*/
|
|
static void serverworks_set_piomode(struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
static const u8 pio_mode[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
|
|
int offset = 1 + 2 * ap->port_no - adev->devno;
|
|
int devbits = (2 * ap->port_no + adev->devno) * 4;
|
|
u16 csb5_pio;
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
int pio = adev->pio_mode - XFER_PIO_0;
|
|
|
|
pci_write_config_byte(pdev, 0x40 + offset, pio_mode[pio]);
|
|
|
|
/* The OSB4 just requires the timing but the CSB series want the
|
|
mode number as well */
|
|
if (serverworks_is_csb(pdev)) {
|
|
pci_read_config_word(pdev, 0x4A, &csb5_pio);
|
|
csb5_pio &= ~(0x0F << devbits);
|
|
pci_write_config_word(pdev, 0x4A, csb5_pio | (pio << devbits));
|
|
}
|
|
}
|
|
|
|
/**
|
|
* serverworks_set_dmamode - set initial DMA mode data
|
|
* @ap: ATA interface
|
|
* @adev: ATA device
|
|
*
|
|
* Program the MWDMA/UDMA modes for the serverworks OSB4/CSB5
|
|
* chipset. The MWDMA mode values are pulled from a lookup table
|
|
* while the chipset uses mode number for UDMA.
|
|
*/
|
|
|
|
static void serverworks_set_dmamode(struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
static const u8 dma_mode[] = { 0x77, 0x21, 0x20 };
|
|
int offset = 1 + 2 * ap->port_no - adev->devno;
|
|
int devbits = 2 * ap->port_no + adev->devno;
|
|
u8 ultra;
|
|
u8 ultra_cfg;
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
|
|
pci_read_config_byte(pdev, 0x54, &ultra_cfg);
|
|
pci_read_config_byte(pdev, 0x56 + ap->port_no, &ultra);
|
|
ultra &= ~(0x0F << (adev->devno * 4));
|
|
|
|
if (adev->dma_mode >= XFER_UDMA_0) {
|
|
pci_write_config_byte(pdev, 0x44 + offset, 0x20);
|
|
|
|
ultra |= (adev->dma_mode - XFER_UDMA_0)
|
|
<< (adev->devno * 4);
|
|
ultra_cfg |= (1 << devbits);
|
|
} else {
|
|
pci_write_config_byte(pdev, 0x44 + offset,
|
|
dma_mode[adev->dma_mode - XFER_MW_DMA_0]);
|
|
ultra_cfg &= ~(1 << devbits);
|
|
}
|
|
pci_write_config_byte(pdev, 0x56 + ap->port_no, ultra);
|
|
pci_write_config_byte(pdev, 0x54, ultra_cfg);
|
|
}
|
|
|
|
static struct scsi_host_template serverworks_osb4_sht = {
|
|
ATA_BMDMA_SHT(DRV_NAME),
|
|
.sg_tablesize = LIBATA_DUMB_MAX_PRD,
|
|
};
|
|
|
|
static struct scsi_host_template serverworks_csb_sht = {
|
|
ATA_BMDMA_SHT(DRV_NAME),
|
|
};
|
|
|
|
static struct ata_port_operations serverworks_osb4_port_ops = {
|
|
.inherits = &ata_bmdma_port_ops,
|
|
.qc_prep = ata_bmdma_dumb_qc_prep,
|
|
.cable_detect = serverworks_cable_detect,
|
|
.mode_filter = serverworks_osb4_filter,
|
|
.set_piomode = serverworks_set_piomode,
|
|
.set_dmamode = serverworks_set_dmamode,
|
|
};
|
|
|
|
static struct ata_port_operations serverworks_csb_port_ops = {
|
|
.inherits = &serverworks_osb4_port_ops,
|
|
.qc_prep = ata_bmdma_qc_prep,
|
|
.mode_filter = serverworks_csb_filter,
|
|
};
|
|
|
|
static int serverworks_fixup_osb4(struct pci_dev *pdev)
|
|
{
|
|
u32 reg;
|
|
struct pci_dev *isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
|
|
PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
|
|
if (isa_dev) {
|
|
pci_read_config_dword(isa_dev, 0x64, ®);
|
|
reg &= ~0x00002000; /* disable 600ns interrupt mask */
|
|
if (!(reg & 0x00004000))
|
|
printk(KERN_DEBUG DRV_NAME ": UDMA not BIOS enabled.\n");
|
|
reg |= 0x00004000; /* enable UDMA/33 support */
|
|
pci_write_config_dword(isa_dev, 0x64, reg);
|
|
pci_dev_put(isa_dev);
|
|
return 0;
|
|
}
|
|
printk(KERN_WARNING DRV_NAME ": Unable to find bridge.\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
static int serverworks_fixup_csb(struct pci_dev *pdev)
|
|
{
|
|
u8 btr;
|
|
|
|
/* Third Channel Test */
|
|
if (!(PCI_FUNC(pdev->devfn) & 1)) {
|
|
struct pci_dev * findev = NULL;
|
|
u32 reg4c = 0;
|
|
findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
|
|
PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
|
|
if (findev) {
|
|
pci_read_config_dword(findev, 0x4C, ®4c);
|
|
reg4c &= ~0x000007FF;
|
|
reg4c |= 0x00000040;
|
|
reg4c |= 0x00000020;
|
|
pci_write_config_dword(findev, 0x4C, reg4c);
|
|
pci_dev_put(findev);
|
|
}
|
|
} else {
|
|
struct pci_dev * findev = NULL;
|
|
u8 reg41 = 0;
|
|
|
|
findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
|
|
PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
|
|
if (findev) {
|
|
pci_read_config_byte(findev, 0x41, ®41);
|
|
reg41 &= ~0x40;
|
|
pci_write_config_byte(findev, 0x41, reg41);
|
|
pci_dev_put(findev);
|
|
}
|
|
}
|
|
/* setup the UDMA Control register
|
|
*
|
|
* 1. clear bit 6 to enable DMA
|
|
* 2. enable DMA modes with bits 0-1
|
|
* 00 : legacy
|
|
* 01 : udma2
|
|
* 10 : udma2/udma4
|
|
* 11 : udma2/udma4/udma5
|
|
*/
|
|
pci_read_config_byte(pdev, 0x5A, &btr);
|
|
btr &= ~0x40;
|
|
if (!(PCI_FUNC(pdev->devfn) & 1))
|
|
btr |= 0x2;
|
|
else
|
|
btr |= (pdev->revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
|
|
pci_write_config_byte(pdev, 0x5A, btr);
|
|
|
|
return btr;
|
|
}
|
|
|
|
static void serverworks_fixup_ht1000(struct pci_dev *pdev)
|
|
{
|
|
u8 btr;
|
|
/* Setup HT1000 SouthBridge Controller - Single Channel Only */
|
|
pci_read_config_byte(pdev, 0x5A, &btr);
|
|
btr &= ~0x40;
|
|
btr |= 0x3;
|
|
pci_write_config_byte(pdev, 0x5A, btr);
|
|
}
|
|
|
|
static int serverworks_fixup(struct pci_dev *pdev)
|
|
{
|
|
int rc = 0;
|
|
|
|
/* Force master latency timer to 64 PCI clocks */
|
|
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40);
|
|
|
|
switch (pdev->device) {
|
|
case PCI_DEVICE_ID_SERVERWORKS_OSB4IDE:
|
|
rc = serverworks_fixup_osb4(pdev);
|
|
break;
|
|
case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
|
|
ata_pci_bmdma_clear_simplex(pdev);
|
|
fallthrough;
|
|
case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
|
|
case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
|
|
rc = serverworks_fixup_csb(pdev);
|
|
break;
|
|
case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
|
|
serverworks_fixup_ht1000(pdev);
|
|
break;
|
|
}
|
|
|
|
return rc;
|
|
}
|
|
|
|
static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
|
|
{
|
|
static const struct ata_port_info info[4] = {
|
|
{ /* OSB4 */
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
.udma_mask = ATA_UDMA2,
|
|
.port_ops = &serverworks_osb4_port_ops
|
|
}, { /* OSB4 no UDMA */
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
/* No UDMA */
|
|
.port_ops = &serverworks_osb4_port_ops
|
|
}, { /* CSB5 */
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
.udma_mask = ATA_UDMA4,
|
|
.port_ops = &serverworks_csb_port_ops
|
|
}, { /* CSB5 - later revisions*/
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
.udma_mask = ATA_UDMA5,
|
|
.port_ops = &serverworks_csb_port_ops
|
|
}
|
|
};
|
|
const struct ata_port_info *ppi[] = { &info[id->driver_data], NULL };
|
|
struct scsi_host_template *sht = &serverworks_csb_sht;
|
|
int rc;
|
|
|
|
rc = pcim_enable_device(pdev);
|
|
if (rc)
|
|
return rc;
|
|
|
|
rc = serverworks_fixup(pdev);
|
|
|
|
/* OSB4 : South Bridge and IDE */
|
|
if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
|
|
/* Select non UDMA capable OSB4 if we can't do fixups */
|
|
if (rc < 0)
|
|
ppi[0] = &info[1];
|
|
sht = &serverworks_osb4_sht;
|
|
}
|
|
/* setup CSB5/CSB6 : South Bridge and IDE option RAID */
|
|
else if ((pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
|
|
(pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
|
|
(pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
|
|
|
|
/* If the returned btr is the newer revision then
|
|
select the right info block */
|
|
if (rc == 3)
|
|
ppi[0] = &info[3];
|
|
|
|
/* Is this the 3rd channel CSB6 IDE ? */
|
|
if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)
|
|
ppi[1] = &ata_dummy_port_info;
|
|
}
|
|
|
|
return ata_pci_bmdma_init_one(pdev, ppi, sht, NULL, 0);
|
|
}
|
|
|
|
#ifdef CONFIG_PM_SLEEP
|
|
static int serverworks_reinit_one(struct pci_dev *pdev)
|
|
{
|
|
struct ata_host *host = pci_get_drvdata(pdev);
|
|
int rc;
|
|
|
|
rc = ata_pci_device_do_resume(pdev);
|
|
if (rc)
|
|
return rc;
|
|
|
|
(void)serverworks_fixup(pdev);
|
|
|
|
ata_host_resume(host);
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
static const struct pci_device_id serverworks[] = {
|
|
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0},
|
|
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 2},
|
|
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2},
|
|
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 2},
|
|
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 2},
|
|
|
|
{ },
|
|
};
|
|
|
|
static struct pci_driver serverworks_pci_driver = {
|
|
.name = DRV_NAME,
|
|
.id_table = serverworks,
|
|
.probe = serverworks_init_one,
|
|
.remove = ata_pci_remove_one,
|
|
#ifdef CONFIG_PM_SLEEP
|
|
.suspend = ata_pci_device_suspend,
|
|
.resume = serverworks_reinit_one,
|
|
#endif
|
|
};
|
|
|
|
module_pci_driver(serverworks_pci_driver);
|
|
|
|
MODULE_AUTHOR("Alan Cox");
|
|
MODULE_DESCRIPTION("low-level driver for Serverworks OSB4/CSB5/CSB6");
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_DEVICE_TABLE(pci, serverworks);
|
|
MODULE_VERSION(DRV_VERSION);
|