416 строки
12 KiB
Plaintext
416 строки
12 KiB
Plaintext
/*
|
|
* Device Tree Source for IBM Embedded PPC 476 Platform
|
|
*
|
|
* Copyright © 2013 Tony Breeds IBM Corporation
|
|
* Copyright © 2013 Alistair Popple IBM Corporation
|
|
*
|
|
* This file is licensed under the terms of the GNU General Public
|
|
* License version 2. This program is licensed "as is" without
|
|
* any warranty of any kind, whether express or implied.
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
/memreserve/ 0x01f00000 0x00100000; // spin table
|
|
|
|
/ {
|
|
#address-cells = <2>;
|
|
#size-cells = <2>;
|
|
model = "ibm,akebono";
|
|
compatible = "ibm,akebono", "ibm,476gtr";
|
|
dcr-parent = <&{/cpus/cpu@0}>;
|
|
|
|
aliases {
|
|
serial0 = &UART0;
|
|
};
|
|
|
|
cpus {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
cpu@0 {
|
|
device_type = "cpu";
|
|
model = "PowerPC,476";
|
|
reg = <0>;
|
|
clock-frequency = <1600000000>; // 1.6 GHz
|
|
timebase-frequency = <100000000>; // 100Mhz
|
|
i-cache-line-size = <32>;
|
|
d-cache-line-size = <32>;
|
|
i-cache-size = <32768>;
|
|
d-cache-size = <32768>;
|
|
dcr-controller;
|
|
dcr-access-method = "native";
|
|
status = "ok";
|
|
};
|
|
cpu@1 {
|
|
device_type = "cpu";
|
|
model = "PowerPC,476";
|
|
reg = <1>;
|
|
clock-frequency = <1600000000>; // 1.6 GHz
|
|
timebase-frequency = <100000000>; // 100Mhz
|
|
i-cache-line-size = <32>;
|
|
d-cache-line-size = <32>;
|
|
i-cache-size = <32768>;
|
|
d-cache-size = <32768>;
|
|
dcr-controller;
|
|
dcr-access-method = "native";
|
|
status = "disabled";
|
|
enable-method = "spin-table";
|
|
cpu-release-addr = <0x0 0x01f00000>;
|
|
};
|
|
};
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0x0 0x0 0x0 0x0>; // filled in by zImage
|
|
};
|
|
|
|
MPIC: interrupt-controller {
|
|
compatible = "chrp,open-pic";
|
|
interrupt-controller;
|
|
dcr-reg = <0xffc00000 0x00040000>;
|
|
#address-cells = <0>;
|
|
#size-cells = <0>;
|
|
#interrupt-cells = <2>;
|
|
single-cpu-affinity;
|
|
};
|
|
|
|
plb {
|
|
compatible = "ibm,plb6";
|
|
#address-cells = <2>;
|
|
#size-cells = <2>;
|
|
ranges;
|
|
clock-frequency = <200000000>; // 200Mhz
|
|
|
|
HSTA0: hsta@310000e0000 {
|
|
compatible = "ibm,476gtr-hsta-msi", "ibm,hsta-msi";
|
|
reg = <0x310 0x000e0000 0x0 0xf0>;
|
|
interrupt-parent = <&MPIC>;
|
|
interrupts = <108 0
|
|
109 0
|
|
110 0
|
|
111 0
|
|
112 0
|
|
113 0
|
|
114 0
|
|
115 0
|
|
116 0
|
|
117 0
|
|
118 0
|
|
119 0
|
|
120 0
|
|
121 0
|
|
122 0
|
|
123 0>;
|
|
};
|
|
|
|
MAL0: mcmal {
|
|
compatible = "ibm,mcmal-476gtr", "ibm,mcmal2";
|
|
dcr-reg = <0xc0000000 0x062>;
|
|
num-tx-chans = <1>;
|
|
num-rx-chans = <1>;
|
|
#address-cells = <0>;
|
|
#size-cells = <0>;
|
|
interrupt-parent = <&MPIC>;
|
|
interrupts = < /*TXEOB*/ 77 0x4
|
|
/*RXEOB*/ 78 0x4
|
|
/*SERR*/ 76 0x4
|
|
/*TXDE*/ 79 0x4
|
|
/*RXDE*/ 80 0x4>;
|
|
};
|
|
|
|
SATA0: sata@30000010000 {
|
|
compatible = "ibm,476gtr-ahci";
|
|
reg = <0x300 0x00010000 0x0 0x10000>;
|
|
interrupt-parent = <&MPIC>;
|
|
interrupts = <93 2>;
|
|
};
|
|
|
|
EHCI0: ehci@30010000000 {
|
|
compatible = "ibm,476gtr-ehci", "generic-ehci";
|
|
reg = <0x300 0x10000000 0x0 0x10000>;
|
|
interrupt-parent = <&MPIC>;
|
|
interrupts = <85 2>;
|
|
};
|
|
|
|
SD0: sd@30000000000 {
|
|
compatible = "ibm,476gtr-sdhci", "generic-sdhci";
|
|
reg = <0x300 0x00000000 0x0 0x10000>;
|
|
interrupts = <91 2>;
|
|
interrupt-parent = <&MPIC>;
|
|
};
|
|
|
|
OHCI0: ohci@30010010000 {
|
|
compatible = "ibm,476gtr-ohci", "generic-ohci";
|
|
reg = <0x300 0x10010000 0x0 0x10000>;
|
|
interrupt-parent = <&MPIC>;
|
|
interrupts = <89 1>;
|
|
};
|
|
|
|
OHCI1: ohci@30010020000 {
|
|
compatible = "ibm,476gtr-ohci", "generic-ohci";
|
|
reg = <0x300 0x10020000 0x0 0x10000>;
|
|
interrupt-parent = <&MPIC>;
|
|
interrupts = <88 1>;
|
|
};
|
|
|
|
POB0: opb {
|
|
compatible = "ibm,opb-4xx", "ibm,opb";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
/* Wish there was a nicer way of specifying a full
|
|
* 32-bit range
|
|
*/
|
|
ranges = <0x00000000 0x0000033f 0x00000000 0x80000000
|
|
0x80000000 0x0000033f 0x80000000 0x80000000>;
|
|
clock-frequency = <100000000>;
|
|
|
|
RGMII0: emac-rgmii-wol@50004 {
|
|
compatible = "ibm,rgmii-wol-476gtr", "ibm,rgmii-wol";
|
|
reg = <0x50004 0x00000008>;
|
|
has-mdio;
|
|
};
|
|
|
|
EMAC0: ethernet@30000 {
|
|
device_type = "network";
|
|
compatible = "ibm,emac-476gtr", "ibm,emac4sync";
|
|
interrupt-parent = <&EMAC0>;
|
|
interrupts = <0x0 0x1>;
|
|
#interrupt-cells = <1>;
|
|
#address-cells = <0>;
|
|
#size-cells = <0>;
|
|
interrupt-map = </*Status*/ 0x0 &MPIC 81 0x4
|
|
/*Wake*/ 0x1 &MPIC 82 0x4>;
|
|
reg = <0x30000 0x78>;
|
|
|
|
/* local-mac-address will normally be added by
|
|
* the wrapper. If your device doesn't support
|
|
* passing data to the wrapper (in the form
|
|
* local-mac-addr=<hwaddr>) then you will need
|
|
* to set it manually here. */
|
|
//local-mac-address = [000000000000];
|
|
|
|
mal-device = <&MAL0>;
|
|
mal-tx-channel = <0>;
|
|
mal-rx-channel = <0>;
|
|
cell-index = <0>;
|
|
max-frame-size = <9000>;
|
|
rx-fifo-size = <4096>;
|
|
tx-fifo-size = <2048>;
|
|
rx-fifo-size-gige = <16384>;
|
|
phy-mode = "rgmii";
|
|
phy-map = <0x00000000>;
|
|
rgmii-wol-device = <&RGMII0>;
|
|
has-inverted-stacr-oc;
|
|
has-new-stacr-staopc;
|
|
};
|
|
|
|
UART0: serial@10000 {
|
|
device_type = "serial";
|
|
compatible = "ns16750", "ns16550";
|
|
reg = <0x10000 0x00000008>;
|
|
virtual-reg = <0xe8010000>;
|
|
clock-frequency = <1851851>;
|
|
current-speed = <38400>;
|
|
interrupt-parent = <&MPIC>;
|
|
interrupts = <39 2>;
|
|
};
|
|
|
|
IIC0: i2c@00000000 {
|
|
compatible = "ibm,iic-476gtr", "ibm,iic";
|
|
reg = <0x0 0x00000020>;
|
|
interrupt-parent = <&MPIC>;
|
|
interrupts = <37 2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
rtc@68 {
|
|
compatible = "stm,m41t80", "m41st85";
|
|
reg = <0x68>;
|
|
};
|
|
};
|
|
|
|
IIC1: i2c@00000100 {
|
|
compatible = "ibm,iic-476gtr", "ibm,iic";
|
|
reg = <0x100 0x00000020>;
|
|
interrupt-parent = <&MPIC>;
|
|
interrupts = <38 2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
avr@58 {
|
|
compatible = "ibm,akebono-avr";
|
|
reg = <0x58>;
|
|
};
|
|
};
|
|
|
|
FPGA0: fpga@ebc00000 {
|
|
compatible = "ibm,akebono-fpga";
|
|
reg = <0xebc00000 0x8>;
|
|
};
|
|
};
|
|
|
|
PCIE0: pciex@10100000000 {
|
|
device_type = "pci";
|
|
#interrupt-cells = <1>;
|
|
#size-cells = <2>;
|
|
#address-cells = <3>;
|
|
compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex";
|
|
primary;
|
|
port = <0x0>; /* port number */
|
|
reg = <0x00000101 0x00000000 0x0 0x10000000 /* Config space access */
|
|
0x00000100 0x00000000 0x0 0x00001000>; /* UTL Registers space access */
|
|
dcr-reg = <0xc0 0x20>;
|
|
|
|
// pci_space < pci_addr > < cpu_addr > < size >
|
|
ranges = <0x02000000 0x00000000 0x80000000 0x00000110 0x80000000 0x0 0x80000000
|
|
0x01000000 0x0 0x0 0x00000140 0x0 0x0 0x00010000>;
|
|
|
|
/* Inbound starting at 0x0 to 0x40000000000. In order to use MSI
|
|
* PCI devices must be able to write to the HSTA module.
|
|
*/
|
|
dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>;
|
|
|
|
/* This drives busses 0 to 0xf */
|
|
bus-range = <0x0 0xf>;
|
|
|
|
/* Legacy interrupts (note the weird polarity, the bridge seems
|
|
* to invert PCIe legacy interrupts).
|
|
* We are de-swizzling here because the numbers are actually for
|
|
* port of the root complex virtual P2P bridge. But I want
|
|
* to avoid putting a node for it in the tree, so the numbers
|
|
* below are basically de-swizzled numbers.
|
|
* The real slot is on idsel 0, so the swizzling is 1:1
|
|
*/
|
|
interrupt-map-mask = <0x0 0x0 0x0 0x7>;
|
|
interrupt-map = <
|
|
0x0 0x0 0x0 0x1 &MPIC 45 0x2 /* int A */
|
|
0x0 0x0 0x0 0x2 &MPIC 46 0x2 /* int B */
|
|
0x0 0x0 0x0 0x3 &MPIC 47 0x2 /* int C */
|
|
0x0 0x0 0x0 0x4 &MPIC 48 0x2 /* int D */>;
|
|
};
|
|
|
|
PCIE1: pciex@20100000000 {
|
|
device_type = "pci";
|
|
#interrupt-cells = <1>;
|
|
#size-cells = <2>;
|
|
#address-cells = <3>;
|
|
compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex";
|
|
primary;
|
|
port = <0x1>; /* port number */
|
|
reg = <0x00000201 0x00000000 0x0 0x10000000 /* Config space access */
|
|
0x00000200 0x00000000 0x0 0x00001000>; /* UTL Registers space access */
|
|
dcr-reg = <0x100 0x20>;
|
|
|
|
// pci_space < pci_addr > < cpu_addr > < size >
|
|
ranges = <0x02000000 0x00000000 0x80000000 0x00000210 0x80000000 0x0 0x80000000
|
|
0x01000000 0x0 0x0 0x00000240 0x0 0x0 0x00010000>;
|
|
|
|
/* Inbound starting at 0x0 to 0x40000000000. In order to use MSI
|
|
* PCI devices must be able to write to the HSTA module.
|
|
*/
|
|
dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>;
|
|
|
|
/* This drives busses 0 to 0xf */
|
|
bus-range = <0x0 0xf>;
|
|
|
|
/* Legacy interrupts (note the weird polarity, the bridge seems
|
|
* to invert PCIe legacy interrupts).
|
|
* We are de-swizzling here because the numbers are actually for
|
|
* port of the root complex virtual P2P bridge. But I want
|
|
* to avoid putting a node for it in the tree, so the numbers
|
|
* below are basically de-swizzled numbers.
|
|
* The real slot is on idsel 0, so the swizzling is 1:1
|
|
*/
|
|
interrupt-map-mask = <0x0 0x0 0x0 0x7>;
|
|
interrupt-map = <
|
|
0x0 0x0 0x0 0x1 &MPIC 53 0x2 /* int A */
|
|
0x0 0x0 0x0 0x2 &MPIC 54 0x2 /* int B */
|
|
0x0 0x0 0x0 0x3 &MPIC 55 0x2 /* int C */
|
|
0x0 0x0 0x0 0x4 &MPIC 56 0x2 /* int D */>;
|
|
};
|
|
|
|
PCIE2: pciex@18100000000 {
|
|
device_type = "pci";
|
|
#interrupt-cells = <1>;
|
|
#size-cells = <2>;
|
|
#address-cells = <3>;
|
|
compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex";
|
|
primary;
|
|
port = <0x2>; /* port number */
|
|
reg = <0x00000181 0x00000000 0x0 0x10000000 /* Config space access */
|
|
0x00000180 0x00000000 0x0 0x00001000>; /* UTL Registers space access */
|
|
dcr-reg = <0xe0 0x20>;
|
|
|
|
// pci_space < pci_addr > < cpu_addr > < size >
|
|
ranges = <0x02000000 0x00000000 0x80000000 0x00000190 0x80000000 0x0 0x80000000
|
|
0x01000000 0x0 0x0 0x000001c0 0x0 0x0 0x00010000>;
|
|
|
|
/* Inbound starting at 0x0 to 0x40000000000. In order to use MSI
|
|
* PCI devices must be able to write to the HSTA module.
|
|
*/
|
|
dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>;
|
|
|
|
/* This drives busses 0 to 0xf */
|
|
bus-range = <0x0 0xf>;
|
|
|
|
/* Legacy interrupts (note the weird polarity, the bridge seems
|
|
* to invert PCIe legacy interrupts).
|
|
* We are de-swizzling here because the numbers are actually for
|
|
* port of the root complex virtual P2P bridge. But I want
|
|
* to avoid putting a node for it in the tree, so the numbers
|
|
* below are basically de-swizzled numbers.
|
|
* The real slot is on idsel 0, so the swizzling is 1:1
|
|
*/
|
|
interrupt-map-mask = <0x0 0x0 0x0 0x7>;
|
|
interrupt-map = <
|
|
0x0 0x0 0x0 0x1 &MPIC 61 0x2 /* int A */
|
|
0x0 0x0 0x0 0x2 &MPIC 62 0x2 /* int B */
|
|
0x0 0x0 0x0 0x3 &MPIC 63 0x2 /* int C */
|
|
0x0 0x0 0x0 0x4 &MPIC 64 0x2 /* int D */>;
|
|
};
|
|
|
|
PCIE3: pciex@28100000000 {
|
|
device_type = "pci";
|
|
#interrupt-cells = <1>;
|
|
#size-cells = <2>;
|
|
#address-cells = <3>;
|
|
compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex";
|
|
primary;
|
|
port = <0x3>; /* port number */
|
|
reg = <0x00000281 0x00000000 0x0 0x10000000 /* Config space access */
|
|
0x00000280 0x00000000 0x0 0x00001000>; /* UTL Registers space access */
|
|
dcr-reg = <0x120 0x20>;
|
|
|
|
// pci_space < pci_addr > < cpu_addr > < size >
|
|
ranges = <0x02000000 0x00000000 0x80000000 0x00000290 0x80000000 0x0 0x80000000
|
|
0x01000000 0x0 0x0 0x000002c0 0x0 0x0 0x00010000>;
|
|
|
|
/* Inbound starting at 0x0 to 0x40000000000. In order to use MSI
|
|
* PCI devices must be able to write to the HSTA module.
|
|
*/
|
|
dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>;
|
|
|
|
/* This drives busses 0 to 0xf */
|
|
bus-range = <0x0 0xf>;
|
|
|
|
/* Legacy interrupts (note the weird polarity, the bridge seems
|
|
* to invert PCIe legacy interrupts).
|
|
* We are de-swizzling here because the numbers are actually for
|
|
* port of the root complex virtual P2P bridge. But I want
|
|
* to avoid putting a node for it in the tree, so the numbers
|
|
* below are basically de-swizzled numbers.
|
|
* The real slot is on idsel 0, so the swizzling is 1:1
|
|
*/
|
|
interrupt-map-mask = <0x0 0x0 0x0 0x7>;
|
|
interrupt-map = <
|
|
0x0 0x0 0x0 0x1 &MPIC 69 0x2 /* int A */
|
|
0x0 0x0 0x0 0x2 &MPIC 70 0x2 /* int B */
|
|
0x0 0x0 0x0 0x3 &MPIC 71 0x2 /* int C */
|
|
0x0 0x0 0x0 0x4 &MPIC 72 0x2 /* int D */>;
|
|
};
|
|
};
|
|
|
|
chosen {
|
|
linux,stdout-path = &UART0;
|
|
};
|
|
};
|