1010 строки
35 KiB
ReStructuredText
1010 строки
35 KiB
ReStructuredText
=====================================
|
|
MTD NAND Driver Programming Interface
|
|
=====================================
|
|
|
|
:Author: Thomas Gleixner
|
|
|
|
Introduction
|
|
============
|
|
|
|
The generic NAND driver supports almost all NAND and AG-AND based chips
|
|
and connects them to the Memory Technology Devices (MTD) subsystem of
|
|
the Linux Kernel.
|
|
|
|
This documentation is provided for developers who want to implement
|
|
board drivers or filesystem drivers suitable for NAND devices.
|
|
|
|
Known Bugs And Assumptions
|
|
==========================
|
|
|
|
None.
|
|
|
|
Documentation hints
|
|
===================
|
|
|
|
The function and structure docs are autogenerated. Each function and
|
|
struct member has a short description which is marked with an [XXX]
|
|
identifier. The following chapters explain the meaning of those
|
|
identifiers.
|
|
|
|
Function identifiers [XXX]
|
|
--------------------------
|
|
|
|
The functions are marked with [XXX] identifiers in the short comment.
|
|
The identifiers explain the usage and scope of the functions. Following
|
|
identifiers are used:
|
|
|
|
- [MTD Interface]
|
|
|
|
These functions provide the interface to the MTD kernel API. They are
|
|
not replaceable and provide functionality which is complete hardware
|
|
independent.
|
|
|
|
- [NAND Interface]
|
|
|
|
These functions are exported and provide the interface to the NAND
|
|
kernel API.
|
|
|
|
- [GENERIC]
|
|
|
|
Generic functions are not replaceable and provide functionality which
|
|
is complete hardware independent.
|
|
|
|
- [DEFAULT]
|
|
|
|
Default functions provide hardware related functionality which is
|
|
suitable for most of the implementations. These functions can be
|
|
replaced by the board driver if necessary. Those functions are called
|
|
via pointers in the NAND chip description structure. The board driver
|
|
can set the functions which should be replaced by board dependent
|
|
functions before calling nand_scan(). If the function pointer is
|
|
NULL on entry to nand_scan() then the pointer is set to the default
|
|
function which is suitable for the detected chip type.
|
|
|
|
Struct member identifiers [XXX]
|
|
-------------------------------
|
|
|
|
The struct members are marked with [XXX] identifiers in the comment. The
|
|
identifiers explain the usage and scope of the members. Following
|
|
identifiers are used:
|
|
|
|
- [INTERN]
|
|
|
|
These members are for NAND driver internal use only and must not be
|
|
modified. Most of these values are calculated from the chip geometry
|
|
information which is evaluated during nand_scan().
|
|
|
|
- [REPLACEABLE]
|
|
|
|
Replaceable members hold hardware related functions which can be
|
|
provided by the board driver. The board driver can set the functions
|
|
which should be replaced by board dependent functions before calling
|
|
nand_scan(). If the function pointer is NULL on entry to
|
|
nand_scan() then the pointer is set to the default function which is
|
|
suitable for the detected chip type.
|
|
|
|
- [BOARDSPECIFIC]
|
|
|
|
Board specific members hold hardware related information which must
|
|
be provided by the board driver. The board driver must set the
|
|
function pointers and datafields before calling nand_scan().
|
|
|
|
- [OPTIONAL]
|
|
|
|
Optional members can hold information relevant for the board driver.
|
|
The generic NAND driver code does not use this information.
|
|
|
|
Basic board driver
|
|
==================
|
|
|
|
For most boards it will be sufficient to provide just the basic
|
|
functions and fill out some really board dependent members in the nand
|
|
chip description structure.
|
|
|
|
Basic defines
|
|
-------------
|
|
|
|
At least you have to provide a nand_chip structure and a storage for
|
|
the ioremap'ed chip address. You can allocate the nand_chip structure
|
|
using kmalloc or you can allocate it statically. The NAND chip structure
|
|
embeds an mtd structure which will be registered to the MTD subsystem.
|
|
You can extract a pointer to the mtd structure from a nand_chip pointer
|
|
using the nand_to_mtd() helper.
|
|
|
|
Kmalloc based example
|
|
|
|
::
|
|
|
|
static struct mtd_info *board_mtd;
|
|
static void __iomem *baseaddr;
|
|
|
|
|
|
Static example
|
|
|
|
::
|
|
|
|
static struct nand_chip board_chip;
|
|
static void __iomem *baseaddr;
|
|
|
|
|
|
Partition defines
|
|
-----------------
|
|
|
|
If you want to divide your device into partitions, then define a
|
|
partitioning scheme suitable to your board.
|
|
|
|
::
|
|
|
|
#define NUM_PARTITIONS 2
|
|
static struct mtd_partition partition_info[] = {
|
|
{ .name = "Flash partition 1",
|
|
.offset = 0,
|
|
.size = 8 * 1024 * 1024 },
|
|
{ .name = "Flash partition 2",
|
|
.offset = MTDPART_OFS_NEXT,
|
|
.size = MTDPART_SIZ_FULL },
|
|
};
|
|
|
|
|
|
Hardware control function
|
|
-------------------------
|
|
|
|
The hardware control function provides access to the control pins of the
|
|
NAND chip(s). The access can be done by GPIO pins or by address lines.
|
|
If you use address lines, make sure that the timing requirements are
|
|
met.
|
|
|
|
*GPIO based example*
|
|
|
|
::
|
|
|
|
static void board_hwcontrol(struct mtd_info *mtd, int cmd)
|
|
{
|
|
switch(cmd){
|
|
case NAND_CTL_SETCLE: /* Set CLE pin high */ break;
|
|
case NAND_CTL_CLRCLE: /* Set CLE pin low */ break;
|
|
case NAND_CTL_SETALE: /* Set ALE pin high */ break;
|
|
case NAND_CTL_CLRALE: /* Set ALE pin low */ break;
|
|
case NAND_CTL_SETNCE: /* Set nCE pin low */ break;
|
|
case NAND_CTL_CLRNCE: /* Set nCE pin high */ break;
|
|
}
|
|
}
|
|
|
|
|
|
*Address lines based example.* It's assumed that the nCE pin is driven
|
|
by a chip select decoder.
|
|
|
|
::
|
|
|
|
static void board_hwcontrol(struct mtd_info *mtd, int cmd)
|
|
{
|
|
struct nand_chip *this = mtd_to_nand(mtd);
|
|
switch(cmd){
|
|
case NAND_CTL_SETCLE: this->legacy.IO_ADDR_W |= CLE_ADRR_BIT; break;
|
|
case NAND_CTL_CLRCLE: this->legacy.IO_ADDR_W &= ~CLE_ADRR_BIT; break;
|
|
case NAND_CTL_SETALE: this->legacy.IO_ADDR_W |= ALE_ADRR_BIT; break;
|
|
case NAND_CTL_CLRALE: this->legacy.IO_ADDR_W &= ~ALE_ADRR_BIT; break;
|
|
}
|
|
}
|
|
|
|
|
|
Device ready function
|
|
---------------------
|
|
|
|
If the hardware interface has the ready busy pin of the NAND chip
|
|
connected to a GPIO or other accessible I/O pin, this function is used
|
|
to read back the state of the pin. The function has no arguments and
|
|
should return 0, if the device is busy (R/B pin is low) and 1, if the
|
|
device is ready (R/B pin is high). If the hardware interface does not
|
|
give access to the ready busy pin, then the function must not be defined
|
|
and the function pointer this->legacy.dev_ready is set to NULL.
|
|
|
|
Init function
|
|
-------------
|
|
|
|
The init function allocates memory and sets up all the board specific
|
|
parameters and function pointers. When everything is set up nand_scan()
|
|
is called. This function tries to detect and identify then chip. If a
|
|
chip is found all the internal data fields are initialized accordingly.
|
|
The structure(s) have to be zeroed out first and then filled with the
|
|
necessary information about the device.
|
|
|
|
::
|
|
|
|
static int __init board_init (void)
|
|
{
|
|
struct nand_chip *this;
|
|
int err = 0;
|
|
|
|
/* Allocate memory for MTD device structure and private data */
|
|
this = kzalloc(sizeof(struct nand_chip), GFP_KERNEL);
|
|
if (!this) {
|
|
printk ("Unable to allocate NAND MTD device structure.\n");
|
|
err = -ENOMEM;
|
|
goto out;
|
|
}
|
|
|
|
board_mtd = nand_to_mtd(this);
|
|
|
|
/* map physical address */
|
|
baseaddr = ioremap(CHIP_PHYSICAL_ADDRESS, 1024);
|
|
if (!baseaddr) {
|
|
printk("Ioremap to access NAND chip failed\n");
|
|
err = -EIO;
|
|
goto out_mtd;
|
|
}
|
|
|
|
/* Set address of NAND IO lines */
|
|
this->legacy.IO_ADDR_R = baseaddr;
|
|
this->legacy.IO_ADDR_W = baseaddr;
|
|
/* Reference hardware control function */
|
|
this->hwcontrol = board_hwcontrol;
|
|
/* Set command delay time, see datasheet for correct value */
|
|
this->legacy.chip_delay = CHIP_DEPENDEND_COMMAND_DELAY;
|
|
/* Assign the device ready function, if available */
|
|
this->legacy.dev_ready = board_dev_ready;
|
|
this->eccmode = NAND_ECC_SOFT;
|
|
|
|
/* Scan to find existence of the device */
|
|
if (nand_scan (this, 1)) {
|
|
err = -ENXIO;
|
|
goto out_ior;
|
|
}
|
|
|
|
add_mtd_partitions(board_mtd, partition_info, NUM_PARTITIONS);
|
|
goto out;
|
|
|
|
out_ior:
|
|
iounmap(baseaddr);
|
|
out_mtd:
|
|
kfree (this);
|
|
out:
|
|
return err;
|
|
}
|
|
module_init(board_init);
|
|
|
|
|
|
Exit function
|
|
-------------
|
|
|
|
The exit function is only necessary if the driver is compiled as a
|
|
module. It releases all resources which are held by the chip driver and
|
|
unregisters the partitions in the MTD layer.
|
|
|
|
::
|
|
|
|
#ifdef MODULE
|
|
static void __exit board_cleanup (void)
|
|
{
|
|
/* Unregister device */
|
|
WARN_ON(mtd_device_unregister(board_mtd));
|
|
/* Release resources */
|
|
nand_cleanup(mtd_to_nand(board_mtd));
|
|
|
|
/* unmap physical address */
|
|
iounmap(baseaddr);
|
|
|
|
/* Free the MTD device structure */
|
|
kfree (mtd_to_nand(board_mtd));
|
|
}
|
|
module_exit(board_cleanup);
|
|
#endif
|
|
|
|
|
|
Advanced board driver functions
|
|
===============================
|
|
|
|
This chapter describes the advanced functionality of the NAND driver.
|
|
For a list of functions which can be overridden by the board driver see
|
|
the documentation of the nand_chip structure.
|
|
|
|
Multiple chip control
|
|
---------------------
|
|
|
|
The nand driver can control chip arrays. Therefore the board driver must
|
|
provide an own select_chip function. This function must (de)select the
|
|
requested chip. The function pointer in the nand_chip structure must be
|
|
set before calling nand_scan(). The maxchip parameter of nand_scan()
|
|
defines the maximum number of chips to scan for. Make sure that the
|
|
select_chip function can handle the requested number of chips.
|
|
|
|
The nand driver concatenates the chips to one virtual chip and provides
|
|
this virtual chip to the MTD layer.
|
|
|
|
*Note: The driver can only handle linear chip arrays of equally sized
|
|
chips. There is no support for parallel arrays which extend the
|
|
buswidth.*
|
|
|
|
*GPIO based example*
|
|
|
|
::
|
|
|
|
static void board_select_chip (struct mtd_info *mtd, int chip)
|
|
{
|
|
/* Deselect all chips, set all nCE pins high */
|
|
GPIO(BOARD_NAND_NCE) |= 0xff;
|
|
if (chip >= 0)
|
|
GPIO(BOARD_NAND_NCE) &= ~ (1 << chip);
|
|
}
|
|
|
|
|
|
*Address lines based example.* Its assumed that the nCE pins are
|
|
connected to an address decoder.
|
|
|
|
::
|
|
|
|
static void board_select_chip (struct mtd_info *mtd, int chip)
|
|
{
|
|
struct nand_chip *this = mtd_to_nand(mtd);
|
|
|
|
/* Deselect all chips */
|
|
this->legacy.IO_ADDR_R &= ~BOARD_NAND_ADDR_MASK;
|
|
this->legacy.IO_ADDR_W &= ~BOARD_NAND_ADDR_MASK;
|
|
switch (chip) {
|
|
case 0:
|
|
this->legacy.IO_ADDR_R |= BOARD_NAND_ADDR_CHIP0;
|
|
this->legacy.IO_ADDR_W |= BOARD_NAND_ADDR_CHIP0;
|
|
break;
|
|
....
|
|
case n:
|
|
this->legacy.IO_ADDR_R |= BOARD_NAND_ADDR_CHIPn;
|
|
this->legacy.IO_ADDR_W |= BOARD_NAND_ADDR_CHIPn;
|
|
break;
|
|
}
|
|
}
|
|
|
|
|
|
Hardware ECC support
|
|
--------------------
|
|
|
|
Functions and constants
|
|
~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
The nand driver supports three different types of hardware ECC.
|
|
|
|
- NAND_ECC_HW3_256
|
|
|
|
Hardware ECC generator providing 3 bytes ECC per 256 byte.
|
|
|
|
- NAND_ECC_HW3_512
|
|
|
|
Hardware ECC generator providing 3 bytes ECC per 512 byte.
|
|
|
|
- NAND_ECC_HW6_512
|
|
|
|
Hardware ECC generator providing 6 bytes ECC per 512 byte.
|
|
|
|
- NAND_ECC_HW8_512
|
|
|
|
Hardware ECC generator providing 8 bytes ECC per 512 byte.
|
|
|
|
If your hardware generator has a different functionality add it at the
|
|
appropriate place in nand_base.c
|
|
|
|
The board driver must provide following functions:
|
|
|
|
- enable_hwecc
|
|
|
|
This function is called before reading / writing to the chip. Reset
|
|
or initialize the hardware generator in this function. The function
|
|
is called with an argument which let you distinguish between read and
|
|
write operations.
|
|
|
|
- calculate_ecc
|
|
|
|
This function is called after read / write from / to the chip.
|
|
Transfer the ECC from the hardware to the buffer. If the option
|
|
NAND_HWECC_SYNDROME is set then the function is only called on
|
|
write. See below.
|
|
|
|
- correct_data
|
|
|
|
In case of an ECC error this function is called for error detection
|
|
and correction. Return 1 respectively 2 in case the error can be
|
|
corrected. If the error is not correctable return -1. If your
|
|
hardware generator matches the default algorithm of the nand_ecc
|
|
software generator then use the correction function provided by
|
|
nand_ecc instead of implementing duplicated code.
|
|
|
|
Hardware ECC with syndrome calculation
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
Many hardware ECC implementations provide Reed-Solomon codes and
|
|
calculate an error syndrome on read. The syndrome must be converted to a
|
|
standard Reed-Solomon syndrome before calling the error correction code
|
|
in the generic Reed-Solomon library.
|
|
|
|
The ECC bytes must be placed immediately after the data bytes in order
|
|
to make the syndrome generator work. This is contrary to the usual
|
|
layout used by software ECC. The separation of data and out of band area
|
|
is not longer possible. The nand driver code handles this layout and the
|
|
remaining free bytes in the oob area are managed by the autoplacement
|
|
code. Provide a matching oob-layout in this case. See rts_from4.c and
|
|
diskonchip.c for implementation reference. In those cases we must also
|
|
use bad block tables on FLASH, because the ECC layout is interfering
|
|
with the bad block marker positions. See bad block table support for
|
|
details.
|
|
|
|
Bad block table support
|
|
-----------------------
|
|
|
|
Most NAND chips mark the bad blocks at a defined position in the spare
|
|
area. Those blocks must not be erased under any circumstances as the bad
|
|
block information would be lost. It is possible to check the bad block
|
|
mark each time when the blocks are accessed by reading the spare area of
|
|
the first page in the block. This is time consuming so a bad block table
|
|
is used.
|
|
|
|
The nand driver supports various types of bad block tables.
|
|
|
|
- Per device
|
|
|
|
The bad block table contains all bad block information of the device
|
|
which can consist of multiple chips.
|
|
|
|
- Per chip
|
|
|
|
A bad block table is used per chip and contains the bad block
|
|
information for this particular chip.
|
|
|
|
- Fixed offset
|
|
|
|
The bad block table is located at a fixed offset in the chip
|
|
(device). This applies to various DiskOnChip devices.
|
|
|
|
- Automatic placed
|
|
|
|
The bad block table is automatically placed and detected either at
|
|
the end or at the beginning of a chip (device)
|
|
|
|
- Mirrored tables
|
|
|
|
The bad block table is mirrored on the chip (device) to allow updates
|
|
of the bad block table without data loss.
|
|
|
|
nand_scan() calls the function nand_default_bbt().
|
|
nand_default_bbt() selects appropriate default bad block table
|
|
descriptors depending on the chip information which was retrieved by
|
|
nand_scan().
|
|
|
|
The standard policy is scanning the device for bad blocks and build a
|
|
ram based bad block table which allows faster access than always
|
|
checking the bad block information on the flash chip itself.
|
|
|
|
Flash based tables
|
|
~~~~~~~~~~~~~~~~~~
|
|
|
|
It may be desired or necessary to keep a bad block table in FLASH. For
|
|
AG-AND chips this is mandatory, as they have no factory marked bad
|
|
blocks. They have factory marked good blocks. The marker pattern is
|
|
erased when the block is erased to be reused. So in case of powerloss
|
|
before writing the pattern back to the chip this block would be lost and
|
|
added to the bad blocks. Therefore we scan the chip(s) when we detect
|
|
them the first time for good blocks and store this information in a bad
|
|
block table before erasing any of the blocks.
|
|
|
|
The blocks in which the tables are stored are protected against
|
|
accidental access by marking them bad in the memory bad block table. The
|
|
bad block table management functions are allowed to circumvent this
|
|
protection.
|
|
|
|
The simplest way to activate the FLASH based bad block table support is
|
|
to set the option NAND_BBT_USE_FLASH in the bbt_option field of the
|
|
nand chip structure before calling nand_scan(). For AG-AND chips is
|
|
this done by default. This activates the default FLASH based bad block
|
|
table functionality of the NAND driver. The default bad block table
|
|
options are
|
|
|
|
- Store bad block table per chip
|
|
|
|
- Use 2 bits per block
|
|
|
|
- Automatic placement at the end of the chip
|
|
|
|
- Use mirrored tables with version numbers
|
|
|
|
- Reserve 4 blocks at the end of the chip
|
|
|
|
User defined tables
|
|
~~~~~~~~~~~~~~~~~~~
|
|
|
|
User defined tables are created by filling out a nand_bbt_descr
|
|
structure and storing the pointer in the nand_chip structure member
|
|
bbt_td before calling nand_scan(). If a mirror table is necessary a
|
|
second structure must be created and a pointer to this structure must be
|
|
stored in bbt_md inside the nand_chip structure. If the bbt_md member
|
|
is set to NULL then only the main table is used and no scan for the
|
|
mirrored table is performed.
|
|
|
|
The most important field in the nand_bbt_descr structure is the
|
|
options field. The options define most of the table properties. Use the
|
|
predefined constants from rawnand.h to define the options.
|
|
|
|
- Number of bits per block
|
|
|
|
The supported number of bits is 1, 2, 4, 8.
|
|
|
|
- Table per chip
|
|
|
|
Setting the constant NAND_BBT_PERCHIP selects that a bad block
|
|
table is managed for each chip in a chip array. If this option is not
|
|
set then a per device bad block table is used.
|
|
|
|
- Table location is absolute
|
|
|
|
Use the option constant NAND_BBT_ABSPAGE and define the absolute
|
|
page number where the bad block table starts in the field pages. If
|
|
you have selected bad block tables per chip and you have a multi chip
|
|
array then the start page must be given for each chip in the chip
|
|
array. Note: there is no scan for a table ident pattern performed, so
|
|
the fields pattern, veroffs, offs, len can be left uninitialized
|
|
|
|
- Table location is automatically detected
|
|
|
|
The table can either be located in the first or the last good blocks
|
|
of the chip (device). Set NAND_BBT_LASTBLOCK to place the bad block
|
|
table at the end of the chip (device). The bad block tables are
|
|
marked and identified by a pattern which is stored in the spare area
|
|
of the first page in the block which holds the bad block table. Store
|
|
a pointer to the pattern in the pattern field. Further the length of
|
|
the pattern has to be stored in len and the offset in the spare area
|
|
must be given in the offs member of the nand_bbt_descr structure.
|
|
For mirrored bad block tables different patterns are mandatory.
|
|
|
|
- Table creation
|
|
|
|
Set the option NAND_BBT_CREATE to enable the table creation if no
|
|
table can be found during the scan. Usually this is done only once if
|
|
a new chip is found.
|
|
|
|
- Table write support
|
|
|
|
Set the option NAND_BBT_WRITE to enable the table write support.
|
|
This allows the update of the bad block table(s) in case a block has
|
|
to be marked bad due to wear. The MTD interface function
|
|
block_markbad is calling the update function of the bad block table.
|
|
If the write support is enabled then the table is updated on FLASH.
|
|
|
|
Note: Write support should only be enabled for mirrored tables with
|
|
version control.
|
|
|
|
- Table version control
|
|
|
|
Set the option NAND_BBT_VERSION to enable the table version
|
|
control. It's highly recommended to enable this for mirrored tables
|
|
with write support. It makes sure that the risk of losing the bad
|
|
block table information is reduced to the loss of the information
|
|
about the one worn out block which should be marked bad. The version
|
|
is stored in 4 consecutive bytes in the spare area of the device. The
|
|
position of the version number is defined by the member veroffs in
|
|
the bad block table descriptor.
|
|
|
|
- Save block contents on write
|
|
|
|
In case that the block which holds the bad block table does contain
|
|
other useful information, set the option NAND_BBT_SAVECONTENT. When
|
|
the bad block table is written then the whole block is read the bad
|
|
block table is updated and the block is erased and everything is
|
|
written back. If this option is not set only the bad block table is
|
|
written and everything else in the block is ignored and erased.
|
|
|
|
- Number of reserved blocks
|
|
|
|
For automatic placement some blocks must be reserved for bad block
|
|
table storage. The number of reserved blocks is defined in the
|
|
maxblocks member of the bad block table description structure.
|
|
Reserving 4 blocks for mirrored tables should be a reasonable number.
|
|
This also limits the number of blocks which are scanned for the bad
|
|
block table ident pattern.
|
|
|
|
Spare area (auto)placement
|
|
--------------------------
|
|
|
|
The nand driver implements different possibilities for placement of
|
|
filesystem data in the spare area,
|
|
|
|
- Placement defined by fs driver
|
|
|
|
- Automatic placement
|
|
|
|
The default placement function is automatic placement. The nand driver
|
|
has built in default placement schemes for the various chiptypes. If due
|
|
to hardware ECC functionality the default placement does not fit then
|
|
the board driver can provide a own placement scheme.
|
|
|
|
File system drivers can provide a own placement scheme which is used
|
|
instead of the default placement scheme.
|
|
|
|
Placement schemes are defined by a nand_oobinfo structure
|
|
|
|
::
|
|
|
|
struct nand_oobinfo {
|
|
int useecc;
|
|
int eccbytes;
|
|
int eccpos[24];
|
|
int oobfree[8][2];
|
|
};
|
|
|
|
|
|
- useecc
|
|
|
|
The useecc member controls the ecc and placement function. The header
|
|
file include/mtd/mtd-abi.h contains constants to select ecc and
|
|
placement. MTD_NANDECC_OFF switches off the ecc complete. This is
|
|
not recommended and available for testing and diagnosis only.
|
|
MTD_NANDECC_PLACE selects caller defined placement,
|
|
MTD_NANDECC_AUTOPLACE selects automatic placement.
|
|
|
|
- eccbytes
|
|
|
|
The eccbytes member defines the number of ecc bytes per page.
|
|
|
|
- eccpos
|
|
|
|
The eccpos array holds the byte offsets in the spare area where the
|
|
ecc codes are placed.
|
|
|
|
- oobfree
|
|
|
|
The oobfree array defines the areas in the spare area which can be
|
|
used for automatic placement. The information is given in the format
|
|
{offset, size}. offset defines the start of the usable area, size the
|
|
length in bytes. More than one area can be defined. The list is
|
|
terminated by an {0, 0} entry.
|
|
|
|
Placement defined by fs driver
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
The calling function provides a pointer to a nand_oobinfo structure
|
|
which defines the ecc placement. For writes the caller must provide a
|
|
spare area buffer along with the data buffer. The spare area buffer size
|
|
is (number of pages) \* (size of spare area). For reads the buffer size
|
|
is (number of pages) \* ((size of spare area) + (number of ecc steps per
|
|
page) \* sizeof (int)). The driver stores the result of the ecc check
|
|
for each tuple in the spare buffer. The storage sequence is::
|
|
|
|
<spare data page 0><ecc result 0>...<ecc result n>
|
|
|
|
...
|
|
|
|
<spare data page n><ecc result 0>...<ecc result n>
|
|
|
|
This is a legacy mode used by YAFFS1.
|
|
|
|
If the spare area buffer is NULL then only the ECC placement is done
|
|
according to the given scheme in the nand_oobinfo structure.
|
|
|
|
Automatic placement
|
|
~~~~~~~~~~~~~~~~~~~
|
|
|
|
Automatic placement uses the built in defaults to place the ecc bytes in
|
|
the spare area. If filesystem data have to be stored / read into the
|
|
spare area then the calling function must provide a buffer. The buffer
|
|
size per page is determined by the oobfree array in the nand_oobinfo
|
|
structure.
|
|
|
|
If the spare area buffer is NULL then only the ECC placement is done
|
|
according to the default builtin scheme.
|
|
|
|
Spare area autoplacement default schemes
|
|
----------------------------------------
|
|
|
|
256 byte pagesize
|
|
~~~~~~~~~~~~~~~~~
|
|
|
|
======== ================== ===================================================
|
|
Offset Content Comment
|
|
======== ================== ===================================================
|
|
0x00 ECC byte 0 Error correction code byte 0
|
|
0x01 ECC byte 1 Error correction code byte 1
|
|
0x02 ECC byte 2 Error correction code byte 2
|
|
0x03 Autoplace 0
|
|
0x04 Autoplace 1
|
|
0x05 Bad block marker If any bit in this byte is zero, then this
|
|
block is bad. This applies only to the first
|
|
page in a block. In the remaining pages this
|
|
byte is reserved
|
|
0x06 Autoplace 2
|
|
0x07 Autoplace 3
|
|
======== ================== ===================================================
|
|
|
|
512 byte pagesize
|
|
~~~~~~~~~~~~~~~~~
|
|
|
|
|
|
============= ================== ==============================================
|
|
Offset Content Comment
|
|
============= ================== ==============================================
|
|
0x00 ECC byte 0 Error correction code byte 0 of the lower
|
|
256 Byte data in this page
|
|
0x01 ECC byte 1 Error correction code byte 1 of the lower
|
|
256 Bytes of data in this page
|
|
0x02 ECC byte 2 Error correction code byte 2 of the lower
|
|
256 Bytes of data in this page
|
|
0x03 ECC byte 3 Error correction code byte 0 of the upper
|
|
256 Bytes of data in this page
|
|
0x04 reserved reserved
|
|
0x05 Bad block marker If any bit in this byte is zero, then this
|
|
block is bad. This applies only to the first
|
|
page in a block. In the remaining pages this
|
|
byte is reserved
|
|
0x06 ECC byte 4 Error correction code byte 1 of the upper
|
|
256 Bytes of data in this page
|
|
0x07 ECC byte 5 Error correction code byte 2 of the upper
|
|
256 Bytes of data in this page
|
|
0x08 - 0x0F Autoplace 0 - 7
|
|
============= ================== ==============================================
|
|
|
|
2048 byte pagesize
|
|
~~~~~~~~~~~~~~~~~~
|
|
|
|
=========== ================== ================================================
|
|
Offset Content Comment
|
|
=========== ================== ================================================
|
|
0x00 Bad block marker If any bit in this byte is zero, then this block
|
|
is bad. This applies only to the first page in a
|
|
block. In the remaining pages this byte is
|
|
reserved
|
|
0x01 Reserved Reserved
|
|
0x02-0x27 Autoplace 0 - 37
|
|
0x28 ECC byte 0 Error correction code byte 0 of the first
|
|
256 Byte data in this page
|
|
0x29 ECC byte 1 Error correction code byte 1 of the first
|
|
256 Bytes of data in this page
|
|
0x2A ECC byte 2 Error correction code byte 2 of the first
|
|
256 Bytes data in this page
|
|
0x2B ECC byte 3 Error correction code byte 0 of the second
|
|
256 Bytes of data in this page
|
|
0x2C ECC byte 4 Error correction code byte 1 of the second
|
|
256 Bytes of data in this page
|
|
0x2D ECC byte 5 Error correction code byte 2 of the second
|
|
256 Bytes of data in this page
|
|
0x2E ECC byte 6 Error correction code byte 0 of the third
|
|
256 Bytes of data in this page
|
|
0x2F ECC byte 7 Error correction code byte 1 of the third
|
|
256 Bytes of data in this page
|
|
0x30 ECC byte 8 Error correction code byte 2 of the third
|
|
256 Bytes of data in this page
|
|
0x31 ECC byte 9 Error correction code byte 0 of the fourth
|
|
256 Bytes of data in this page
|
|
0x32 ECC byte 10 Error correction code byte 1 of the fourth
|
|
256 Bytes of data in this page
|
|
0x33 ECC byte 11 Error correction code byte 2 of the fourth
|
|
256 Bytes of data in this page
|
|
0x34 ECC byte 12 Error correction code byte 0 of the fifth
|
|
256 Bytes of data in this page
|
|
0x35 ECC byte 13 Error correction code byte 1 of the fifth
|
|
256 Bytes of data in this page
|
|
0x36 ECC byte 14 Error correction code byte 2 of the fifth
|
|
256 Bytes of data in this page
|
|
0x37 ECC byte 15 Error correction code byte 0 of the sixth
|
|
256 Bytes of data in this page
|
|
0x38 ECC byte 16 Error correction code byte 1 of the sixth
|
|
256 Bytes of data in this page
|
|
0x39 ECC byte 17 Error correction code byte 2 of the sixth
|
|
256 Bytes of data in this page
|
|
0x3A ECC byte 18 Error correction code byte 0 of the seventh
|
|
256 Bytes of data in this page
|
|
0x3B ECC byte 19 Error correction code byte 1 of the seventh
|
|
256 Bytes of data in this page
|
|
0x3C ECC byte 20 Error correction code byte 2 of the seventh
|
|
256 Bytes of data in this page
|
|
0x3D ECC byte 21 Error correction code byte 0 of the eighth
|
|
256 Bytes of data in this page
|
|
0x3E ECC byte 22 Error correction code byte 1 of the eighth
|
|
256 Bytes of data in this page
|
|
0x3F ECC byte 23 Error correction code byte 2 of the eighth
|
|
256 Bytes of data in this page
|
|
=========== ================== ================================================
|
|
|
|
Filesystem support
|
|
==================
|
|
|
|
The NAND driver provides all necessary functions for a filesystem via
|
|
the MTD interface.
|
|
|
|
Filesystems must be aware of the NAND peculiarities and restrictions.
|
|
One major restrictions of NAND Flash is, that you cannot write as often
|
|
as you want to a page. The consecutive writes to a page, before erasing
|
|
it again, are restricted to 1-3 writes, depending on the manufacturers
|
|
specifications. This applies similar to the spare area.
|
|
|
|
Therefore NAND aware filesystems must either write in page size chunks
|
|
or hold a writebuffer to collect smaller writes until they sum up to
|
|
pagesize. Available NAND aware filesystems: JFFS2, YAFFS.
|
|
|
|
The spare area usage to store filesystem data is controlled by the spare
|
|
area placement functionality which is described in one of the earlier
|
|
chapters.
|
|
|
|
Tools
|
|
=====
|
|
|
|
The MTD project provides a couple of helpful tools to handle NAND Flash.
|
|
|
|
- flasherase, flasheraseall: Erase and format FLASH partitions
|
|
|
|
- nandwrite: write filesystem images to NAND FLASH
|
|
|
|
- nanddump: dump the contents of a NAND FLASH partitions
|
|
|
|
These tools are aware of the NAND restrictions. Please use those tools
|
|
instead of complaining about errors which are caused by non NAND aware
|
|
access methods.
|
|
|
|
Constants
|
|
=========
|
|
|
|
This chapter describes the constants which might be relevant for a
|
|
driver developer.
|
|
|
|
Chip option constants
|
|
---------------------
|
|
|
|
Constants for chip id table
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
These constants are defined in rawnand.h. They are OR-ed together to
|
|
describe the chip functionality::
|
|
|
|
/* Buswitdh is 16 bit */
|
|
#define NAND_BUSWIDTH_16 0x00000002
|
|
/* Device supports partial programming without padding */
|
|
#define NAND_NO_PADDING 0x00000004
|
|
/* Chip has cache program function */
|
|
#define NAND_CACHEPRG 0x00000008
|
|
/* Chip has copy back function */
|
|
#define NAND_COPYBACK 0x00000010
|
|
/* AND Chip which has 4 banks and a confusing page / block
|
|
* assignment. See Renesas datasheet for further information */
|
|
#define NAND_IS_AND 0x00000020
|
|
/* Chip has a array of 4 pages which can be read without
|
|
* additional ready /busy waits */
|
|
#define NAND_4PAGE_ARRAY 0x00000040
|
|
|
|
|
|
Constants for runtime options
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
These constants are defined in rawnand.h. They are OR-ed together to
|
|
describe the functionality::
|
|
|
|
/* The hw ecc generator provides a syndrome instead a ecc value on read
|
|
* This can only work if we have the ecc bytes directly behind the
|
|
* data bytes. Applies for DOC and AG-AND Renesas HW Reed Solomon generators */
|
|
#define NAND_HWECC_SYNDROME 0x00020000
|
|
|
|
|
|
ECC selection constants
|
|
-----------------------
|
|
|
|
Use these constants to select the ECC algorithm::
|
|
|
|
/* No ECC. Usage is not recommended ! */
|
|
#define NAND_ECC_NONE 0
|
|
/* Software ECC 3 byte ECC per 256 Byte data */
|
|
#define NAND_ECC_SOFT 1
|
|
/* Hardware ECC 3 byte ECC per 256 Byte data */
|
|
#define NAND_ECC_HW3_256 2
|
|
/* Hardware ECC 3 byte ECC per 512 Byte data */
|
|
#define NAND_ECC_HW3_512 3
|
|
/* Hardware ECC 6 byte ECC per 512 Byte data */
|
|
#define NAND_ECC_HW6_512 4
|
|
/* Hardware ECC 8 byte ECC per 512 Byte data */
|
|
#define NAND_ECC_HW8_512 6
|
|
|
|
|
|
Hardware control related constants
|
|
----------------------------------
|
|
|
|
These constants describe the requested hardware access function when the
|
|
boardspecific hardware control function is called::
|
|
|
|
/* Select the chip by setting nCE to low */
|
|
#define NAND_CTL_SETNCE 1
|
|
/* Deselect the chip by setting nCE to high */
|
|
#define NAND_CTL_CLRNCE 2
|
|
/* Select the command latch by setting CLE to high */
|
|
#define NAND_CTL_SETCLE 3
|
|
/* Deselect the command latch by setting CLE to low */
|
|
#define NAND_CTL_CLRCLE 4
|
|
/* Select the address latch by setting ALE to high */
|
|
#define NAND_CTL_SETALE 5
|
|
/* Deselect the address latch by setting ALE to low */
|
|
#define NAND_CTL_CLRALE 6
|
|
/* Set write protection by setting WP to high. Not used! */
|
|
#define NAND_CTL_SETWP 7
|
|
/* Clear write protection by setting WP to low. Not used! */
|
|
#define NAND_CTL_CLRWP 8
|
|
|
|
|
|
Bad block table related constants
|
|
---------------------------------
|
|
|
|
These constants describe the options used for bad block table
|
|
descriptors::
|
|
|
|
/* Options for the bad block table descriptors */
|
|
|
|
/* The number of bits used per block in the bbt on the device */
|
|
#define NAND_BBT_NRBITS_MSK 0x0000000F
|
|
#define NAND_BBT_1BIT 0x00000001
|
|
#define NAND_BBT_2BIT 0x00000002
|
|
#define NAND_BBT_4BIT 0x00000004
|
|
#define NAND_BBT_8BIT 0x00000008
|
|
/* The bad block table is in the last good block of the device */
|
|
#define NAND_BBT_LASTBLOCK 0x00000010
|
|
/* The bbt is at the given page, else we must scan for the bbt */
|
|
#define NAND_BBT_ABSPAGE 0x00000020
|
|
/* bbt is stored per chip on multichip devices */
|
|
#define NAND_BBT_PERCHIP 0x00000080
|
|
/* bbt has a version counter at offset veroffs */
|
|
#define NAND_BBT_VERSION 0x00000100
|
|
/* Create a bbt if none axists */
|
|
#define NAND_BBT_CREATE 0x00000200
|
|
/* Write bbt if necessary */
|
|
#define NAND_BBT_WRITE 0x00001000
|
|
/* Read and write back block contents when writing bbt */
|
|
#define NAND_BBT_SAVECONTENT 0x00002000
|
|
|
|
|
|
Structures
|
|
==========
|
|
|
|
This chapter contains the autogenerated documentation of the structures
|
|
which are used in the NAND driver and might be relevant for a driver
|
|
developer. Each struct member has a short description which is marked
|
|
with an [XXX] identifier. See the chapter "Documentation hints" for an
|
|
explanation.
|
|
|
|
.. kernel-doc:: include/linux/mtd/rawnand.h
|
|
:internal:
|
|
|
|
Public Functions Provided
|
|
=========================
|
|
|
|
This chapter contains the autogenerated documentation of the NAND kernel
|
|
API functions which are exported. Each function has a short description
|
|
which is marked with an [XXX] identifier. See the chapter "Documentation
|
|
hints" for an explanation.
|
|
|
|
.. kernel-doc:: drivers/mtd/nand/raw/nand_base.c
|
|
:export:
|
|
|
|
.. kernel-doc:: drivers/mtd/nand/raw/nand_ecc.c
|
|
:export:
|
|
|
|
Internal Functions Provided
|
|
===========================
|
|
|
|
This chapter contains the autogenerated documentation of the NAND driver
|
|
internal functions. Each function has a short description which is
|
|
marked with an [XXX] identifier. See the chapter "Documentation hints"
|
|
for an explanation. The functions marked with [DEFAULT] might be
|
|
relevant for a board driver developer.
|
|
|
|
.. kernel-doc:: drivers/mtd/nand/raw/nand_base.c
|
|
:internal:
|
|
|
|
.. kernel-doc:: drivers/mtd/nand/raw/nand_bbt.c
|
|
:internal:
|
|
|
|
Credits
|
|
=======
|
|
|
|
The following people have contributed to the NAND driver:
|
|
|
|
1. Steven J. Hill\ sjhill@realitydiluted.com
|
|
|
|
2. David Woodhouse\ dwmw2@infradead.org
|
|
|
|
3. Thomas Gleixner\ tglx@linutronix.de
|
|
|
|
A lot of users have provided bugfixes, improvements and helping hands
|
|
for testing. Thanks a lot.
|
|
|
|
The following people have contributed to this document:
|
|
|
|
1. Thomas Gleixner\ tglx@linutronix.de
|