391 строка
16 KiB
ReStructuredText
391 строка
16 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0
|
|
|
|
=========================
|
|
Introduction to LoongArch
|
|
=========================
|
|
|
|
LoongArch is a new RISC ISA, which is a bit like MIPS or RISC-V. There are
|
|
currently 3 variants: a reduced 32-bit version (LA32R), a standard 32-bit
|
|
version (LA32S) and a 64-bit version (LA64). There are 4 privilege levels
|
|
(PLVs) defined in LoongArch: PLV0~PLV3, from high to low. Kernel runs at PLV0
|
|
while applications run at PLV3. This document introduces the registers, basic
|
|
instruction set, virtual memory and some other topics of LoongArch.
|
|
|
|
Registers
|
|
=========
|
|
|
|
LoongArch registers include general purpose registers (GPRs), floating point
|
|
registers (FPRs), vector registers (VRs) and control status registers (CSRs)
|
|
used in privileged mode (PLV0).
|
|
|
|
GPRs
|
|
----
|
|
|
|
LoongArch has 32 GPRs ( ``$r0`` ~ ``$r31`` ); each one is 32-bit wide in LA32
|
|
and 64-bit wide in LA64. ``$r0`` is hard-wired to zero, and the other registers
|
|
are not architecturally special. (Except ``$r1``, which is hard-wired as the
|
|
link register of the BL instruction.)
|
|
|
|
The kernel uses a variant of the LoongArch register convention, as described in
|
|
the LoongArch ELF psABI spec, in :ref:`References <loongarch-references>`:
|
|
|
|
================= =============== =================== ============
|
|
Name Alias Usage Preserved
|
|
across calls
|
|
================= =============== =================== ============
|
|
``$r0`` ``$zero`` Constant zero Unused
|
|
``$r1`` ``$ra`` Return address No
|
|
``$r2`` ``$tp`` TLS/Thread pointer Unused
|
|
``$r3`` ``$sp`` Stack pointer Yes
|
|
``$r4``-``$r11`` ``$a0``-``$a7`` Argument registers No
|
|
``$r4``-``$r5`` ``$v0``-``$v1`` Return value No
|
|
``$r12``-``$r20`` ``$t0``-``$t8`` Temp registers No
|
|
``$r21`` ``$u0`` Percpu base address Unused
|
|
``$r22`` ``$fp`` Frame pointer Yes
|
|
``$r23``-``$r31`` ``$s0``-``$s8`` Static registers Yes
|
|
================= =============== =================== ============
|
|
|
|
.. Note::
|
|
The register ``$r21`` is reserved in the ELF psABI, but used by the Linux
|
|
kernel for storing the percpu base address. It normally has no ABI name,
|
|
but is called ``$u0`` in the kernel. You may also see ``$v0`` or ``$v1``
|
|
in some old code,however they are deprecated aliases of ``$a0`` and ``$a1``
|
|
respectively.
|
|
|
|
FPRs
|
|
----
|
|
|
|
LoongArch has 32 FPRs ( ``$f0`` ~ ``$f31`` ) when FPU is present. Each one is
|
|
64-bit wide on the LA64 cores.
|
|
|
|
The floating-point register convention is the same as described in the
|
|
LoongArch ELF psABI spec:
|
|
|
|
================= ================== =================== ============
|
|
Name Alias Usage Preserved
|
|
across calls
|
|
================= ================== =================== ============
|
|
``$f0``-``$f7`` ``$fa0``-``$fa7`` Argument registers No
|
|
``$f0``-``$f1`` ``$fv0``-``$fv1`` Return value No
|
|
``$f8``-``$f23`` ``$ft0``-``$ft15`` Temp registers No
|
|
``$f24``-``$f31`` ``$fs0``-``$fs7`` Static registers Yes
|
|
================= ================== =================== ============
|
|
|
|
.. Note::
|
|
You may see ``$fv0`` or ``$fv1`` in some old code, however they are
|
|
deprecated aliases of ``$fa0`` and ``$fa1`` respectively.
|
|
|
|
VRs
|
|
----
|
|
|
|
There are currently 2 vector extensions to LoongArch:
|
|
|
|
- LSX (Loongson SIMD eXtension) with 128-bit vectors,
|
|
- LASX (Loongson Advanced SIMD eXtension) with 256-bit vectors.
|
|
|
|
LSX brings ``$v0`` ~ ``$v31`` while LASX brings ``$x0`` ~ ``$x31`` as the vector
|
|
registers.
|
|
|
|
The VRs overlap with FPRs: for example, on a core implementing LSX and LASX,
|
|
the lower 128 bits of ``$x0`` is shared with ``$v0``, and the lower 64 bits of
|
|
``$v0`` is shared with ``$f0``; same with all other VRs.
|
|
|
|
CSRs
|
|
----
|
|
|
|
CSRs can only be accessed from privileged mode (PLV0):
|
|
|
|
================= ===================================== ==============
|
|
Address Full Name Abbrev Name
|
|
================= ===================================== ==============
|
|
0x0 Current Mode Information CRMD
|
|
0x1 Pre-exception Mode Information PRMD
|
|
0x2 Extension Unit Enable EUEN
|
|
0x3 Miscellaneous Control MISC
|
|
0x4 Exception Configuration ECFG
|
|
0x5 Exception Status ESTAT
|
|
0x6 Exception Return Address ERA
|
|
0x7 Bad (Faulting) Virtual Address BADV
|
|
0x8 Bad (Faulting) Instruction Word BADI
|
|
0xC Exception Entrypoint Address EENTRY
|
|
0x10 TLB Index TLBIDX
|
|
0x11 TLB Entry High-order Bits TLBEHI
|
|
0x12 TLB Entry Low-order Bits 0 TLBELO0
|
|
0x13 TLB Entry Low-order Bits 1 TLBELO1
|
|
0x18 Address Space Identifier ASID
|
|
0x19 Page Global Directory Address for PGDL
|
|
Lower-half Address Space
|
|
0x1A Page Global Directory Address for PGDH
|
|
Higher-half Address Space
|
|
0x1B Page Global Directory Address PGD
|
|
0x1C Page Walk Control for Lower- PWCL
|
|
half Address Space
|
|
0x1D Page Walk Control for Higher- PWCH
|
|
half Address Space
|
|
0x1E STLB Page Size STLBPS
|
|
0x1F Reduced Virtual Address Configuration RVACFG
|
|
0x20 CPU Identifier CPUID
|
|
0x21 Privileged Resource Configuration 1 PRCFG1
|
|
0x22 Privileged Resource Configuration 2 PRCFG2
|
|
0x23 Privileged Resource Configuration 3 PRCFG3
|
|
0x30+n (0≤n≤15) Saved Data register SAVEn
|
|
0x40 Timer Identifier TID
|
|
0x41 Timer Configuration TCFG
|
|
0x42 Timer Value TVAL
|
|
0x43 Compensation of Timer Count CNTC
|
|
0x44 Timer Interrupt Clearing TICLR
|
|
0x60 LLBit Control LLBCTL
|
|
0x80 Implementation-specific Control 1 IMPCTL1
|
|
0x81 Implementation-specific Control 2 IMPCTL2
|
|
0x88 TLB Refill Exception Entrypoint TLBRENTRY
|
|
Address
|
|
0x89 TLB Refill Exception BAD (Faulting) TLBRBADV
|
|
Virtual Address
|
|
0x8A TLB Refill Exception Return Address TLBRERA
|
|
0x8B TLB Refill Exception Saved Data TLBRSAVE
|
|
Register
|
|
0x8C TLB Refill Exception Entry Low-order TLBRELO0
|
|
Bits 0
|
|
0x8D TLB Refill Exception Entry Low-order TLBRELO1
|
|
Bits 1
|
|
0x8E TLB Refill Exception Entry High-order TLBEHI
|
|
Bits
|
|
0x8F TLB Refill Exception Pre-exception TLBRPRMD
|
|
Mode Information
|
|
0x90 Machine Error Control MERRCTL
|
|
0x91 Machine Error Information 1 MERRINFO1
|
|
0x92 Machine Error Information 2 MERRINFO2
|
|
0x93 Machine Error Exception Entrypoint MERRENTRY
|
|
Address
|
|
0x94 Machine Error Exception Return MERRERA
|
|
Address
|
|
0x95 Machine Error Exception Saved Data MERRSAVE
|
|
Register
|
|
0x98 Cache TAGs CTAG
|
|
0x180+n (0≤n≤3) Direct Mapping Configuration Window n DMWn
|
|
0x200+2n (0≤n≤31) Performance Monitor Configuration n PMCFGn
|
|
0x201+2n (0≤n≤31) Performance Monitor Overall Counter n PMCNTn
|
|
0x300 Memory Load/Store WatchPoint MWPC
|
|
Overall Control
|
|
0x301 Memory Load/Store WatchPoint MWPS
|
|
Overall Status
|
|
0x310+8n (0≤n≤7) Memory Load/Store WatchPoint n MWPnCFG1
|
|
Configuration 1
|
|
0x311+8n (0≤n≤7) Memory Load/Store WatchPoint n MWPnCFG2
|
|
Configuration 2
|
|
0x312+8n (0≤n≤7) Memory Load/Store WatchPoint n MWPnCFG3
|
|
Configuration 3
|
|
0x313+8n (0≤n≤7) Memory Load/Store WatchPoint n MWPnCFG4
|
|
Configuration 4
|
|
0x380 Instruction Fetch WatchPoint FWPC
|
|
Overall Control
|
|
0x381 Instruction Fetch WatchPoint FWPS
|
|
Overall Status
|
|
0x390+8n (0≤n≤7) Instruction Fetch WatchPoint n FWPnCFG1
|
|
Configuration 1
|
|
0x391+8n (0≤n≤7) Instruction Fetch WatchPoint n FWPnCFG2
|
|
Configuration 2
|
|
0x392+8n (0≤n≤7) Instruction Fetch WatchPoint n FWPnCFG3
|
|
Configuration 3
|
|
0x393+8n (0≤n≤7) Instruction Fetch WatchPoint n FWPnCFG4
|
|
Configuration 4
|
|
0x500 Debug Register DBG
|
|
0x501 Debug Exception Return Address DERA
|
|
0x502 Debug Exception Saved Data Register DSAVE
|
|
================= ===================================== ==============
|
|
|
|
ERA, TLBRERA, MERRERA and DERA are sometimes also known as EPC, TLBREPC, MERREPC
|
|
and DEPC respectively.
|
|
|
|
Basic Instruction Set
|
|
=====================
|
|
|
|
Instruction formats
|
|
-------------------
|
|
|
|
LoongArch instructions are 32 bits wide, belonging to 9 basic instruction
|
|
formats (and variants of them):
|
|
|
|
=========== ==========================
|
|
Format name Composition
|
|
=========== ==========================
|
|
2R Opcode + Rj + Rd
|
|
3R Opcode + Rk + Rj + Rd
|
|
4R Opcode + Ra + Rk + Rj + Rd
|
|
2RI8 Opcode + I8 + Rj + Rd
|
|
2RI12 Opcode + I12 + Rj + Rd
|
|
2RI14 Opcode + I14 + Rj + Rd
|
|
2RI16 Opcode + I16 + Rj + Rd
|
|
1RI21 Opcode + I21L + Rj + I21H
|
|
I26 Opcode + I26L + I26H
|
|
=========== ==========================
|
|
|
|
Rd is the destination register operand, while Rj, Rk and Ra ("a" stands for
|
|
"additional") are the source register operands. I8/I12/I14/I16/I21/I26 are
|
|
immediate operands of respective width. The longer I21 and I26 are stored
|
|
in separate higher and lower parts in the instruction word, denoted by the "L"
|
|
and "H" suffixes.
|
|
|
|
List of Instructions
|
|
--------------------
|
|
|
|
For brevity, only instruction names (mnemonics) are listed here; please see the
|
|
:ref:`References <loongarch-references>` for details.
|
|
|
|
|
|
1. Arithmetic Instructions::
|
|
|
|
ADD.W SUB.W ADDI.W ADD.D SUB.D ADDI.D
|
|
SLT SLTU SLTI SLTUI
|
|
AND OR NOR XOR ANDN ORN ANDI ORI XORI
|
|
MUL.W MULH.W MULH.WU DIV.W DIV.WU MOD.W MOD.WU
|
|
MUL.D MULH.D MULH.DU DIV.D DIV.DU MOD.D MOD.DU
|
|
PCADDI PCADDU12I PCADDU18I
|
|
LU12I.W LU32I.D LU52I.D ADDU16I.D
|
|
|
|
2. Bit-shift Instructions::
|
|
|
|
SLL.W SRL.W SRA.W ROTR.W SLLI.W SRLI.W SRAI.W ROTRI.W
|
|
SLL.D SRL.D SRA.D ROTR.D SLLI.D SRLI.D SRAI.D ROTRI.D
|
|
|
|
3. Bit-manipulation Instructions::
|
|
|
|
EXT.W.B EXT.W.H CLO.W CLO.D SLZ.W CLZ.D CTO.W CTO.D CTZ.W CTZ.D
|
|
BYTEPICK.W BYTEPICK.D BSTRINS.W BSTRINS.D BSTRPICK.W BSTRPICK.D
|
|
REVB.2H REVB.4H REVB.2W REVB.D REVH.2W REVH.D BITREV.4B BITREV.8B BITREV.W BITREV.D
|
|
MASKEQZ MASKNEZ
|
|
|
|
4. Branch Instructions::
|
|
|
|
BEQ BNE BLT BGE BLTU BGEU BEQZ BNEZ B BL JIRL
|
|
|
|
5. Load/Store Instructions::
|
|
|
|
LD.B LD.BU LD.H LD.HU LD.W LD.WU LD.D ST.B ST.H ST.W ST.D
|
|
LDX.B LDX.BU LDX.H LDX.HU LDX.W LDX.WU LDX.D STX.B STX.H STX.W STX.D
|
|
LDPTR.W LDPTR.D STPTR.W STPTR.D
|
|
PRELD PRELDX
|
|
|
|
6. Atomic Operation Instructions::
|
|
|
|
LL.W SC.W LL.D SC.D
|
|
AMSWAP.W AMSWAP.D AMADD.W AMADD.D AMAND.W AMAND.D AMOR.W AMOR.D AMXOR.W AMXOR.D
|
|
AMMAX.W AMMAX.D AMMIN.W AMMIN.D
|
|
|
|
7. Barrier Instructions::
|
|
|
|
IBAR DBAR
|
|
|
|
8. Special Instructions::
|
|
|
|
SYSCALL BREAK CPUCFG NOP IDLE ERTN(ERET) DBCL(DBGCALL) RDTIMEL.W RDTIMEH.W RDTIME.D
|
|
ASRTLE.D ASRTGT.D
|
|
|
|
9. Privileged Instructions::
|
|
|
|
CSRRD CSRWR CSRXCHG
|
|
IOCSRRD.B IOCSRRD.H IOCSRRD.W IOCSRRD.D IOCSRWR.B IOCSRWR.H IOCSRWR.W IOCSRWR.D
|
|
CACOP TLBP(TLBSRCH) TLBRD TLBWR TLBFILL TLBCLR TLBFLUSH INVTLB LDDIR LDPTE
|
|
|
|
Virtual Memory
|
|
==============
|
|
|
|
LoongArch supports direct-mapped virtual memory and page-mapped virtual memory.
|
|
|
|
Direct-mapped virtual memory is configured by CSR.DMWn (n=0~3), it has a simple
|
|
relationship between virtual address (VA) and physical address (PA)::
|
|
|
|
VA = PA + FixedOffset
|
|
|
|
Page-mapped virtual memory has arbitrary relationship between VA and PA, which
|
|
is recorded in TLB and page tables. LoongArch's TLB includes a fully-associative
|
|
MTLB (Multiple Page Size TLB) and set-associative STLB (Single Page Size TLB).
|
|
|
|
By default, the whole virtual address space of LA32 is configured like this:
|
|
|
|
============ =========================== =============================
|
|
Name Address Range Attributes
|
|
============ =========================== =============================
|
|
``UVRANGE`` ``0x00000000 - 0x7FFFFFFF`` Page-mapped, Cached, PLV0~3
|
|
``KPRANGE0`` ``0x80000000 - 0x9FFFFFFF`` Direct-mapped, Uncached, PLV0
|
|
``KPRANGE1`` ``0xA0000000 - 0xBFFFFFFF`` Direct-mapped, Cached, PLV0
|
|
``KVRANGE`` ``0xC0000000 - 0xFFFFFFFF`` Page-mapped, Cached, PLV0
|
|
============ =========================== =============================
|
|
|
|
User mode (PLV3) can only access UVRANGE. For direct-mapped KPRANGE0 and
|
|
KPRANGE1, PA is equal to VA with bit30~31 cleared. For example, the uncached
|
|
direct-mapped VA of 0x00001000 is 0x80001000, and the cached direct-mapped
|
|
VA of 0x00001000 is 0xA0001000.
|
|
|
|
By default, the whole virtual address space of LA64 is configured like this:
|
|
|
|
============ ====================== ======================================
|
|
Name Address Range Attributes
|
|
============ ====================== ======================================
|
|
``XUVRANGE`` ``0x0000000000000000 - Page-mapped, Cached, PLV0~3
|
|
0x3FFFFFFFFFFFFFFF``
|
|
``XSPRANGE`` ``0x4000000000000000 - Direct-mapped, Cached / Uncached, PLV0
|
|
0x7FFFFFFFFFFFFFFF``
|
|
``XKPRANGE`` ``0x8000000000000000 - Direct-mapped, Cached / Uncached, PLV0
|
|
0xBFFFFFFFFFFFFFFF``
|
|
``XKVRANGE`` ``0xC000000000000000 - Page-mapped, Cached, PLV0
|
|
0xFFFFFFFFFFFFFFFF``
|
|
============ ====================== ======================================
|
|
|
|
User mode (PLV3) can only access XUVRANGE. For direct-mapped XSPRANGE and
|
|
XKPRANGE, PA is equal to VA with bits 60~63 cleared, and the cache attribute
|
|
is configured by bits 60~61 in VA: 0 is for strongly-ordered uncached, 1 is
|
|
for coherent cached, and 2 is for weakly-ordered uncached.
|
|
|
|
Currently we only use XKPRANGE for direct mapping and XSPRANGE is reserved.
|
|
|
|
To put this in action: the strongly-ordered uncached direct-mapped VA (in
|
|
XKPRANGE) of 0x00000000_00001000 is 0x80000000_00001000, the coherent cached
|
|
direct-mapped VA (in XKPRANGE) of 0x00000000_00001000 is 0x90000000_00001000,
|
|
and the weakly-ordered uncached direct-mapped VA (in XKPRANGE) of 0x00000000
|
|
_00001000 is 0xA0000000_00001000.
|
|
|
|
Relationship of Loongson and LoongArch
|
|
======================================
|
|
|
|
LoongArch is a RISC ISA which is different from any other existing ones, while
|
|
Loongson is a family of processors. Loongson includes 3 series: Loongson-1 is
|
|
the 32-bit processor series, Loongson-2 is the low-end 64-bit processor series,
|
|
and Loongson-3 is the high-end 64-bit processor series. Old Loongson is based on
|
|
MIPS, while New Loongson is based on LoongArch. Take Loongson-3 as an example:
|
|
Loongson-3A1000/3B1500/3A2000/3A3000/3A4000 are MIPS-compatible, while Loongson-
|
|
3A5000 (and future revisions) are all based on LoongArch.
|
|
|
|
.. _loongarch-references:
|
|
|
|
References
|
|
==========
|
|
|
|
Official web site of Loongson Technology Corp. Ltd.:
|
|
|
|
http://www.loongson.cn/
|
|
|
|
Developer web site of Loongson and LoongArch (Software and Documentation):
|
|
|
|
http://www.loongnix.cn/
|
|
|
|
https://github.com/loongson/
|
|
|
|
https://loongson.github.io/LoongArch-Documentation/
|
|
|
|
Documentation of LoongArch ISA:
|
|
|
|
https://github.com/loongson/LoongArch-Documentation/releases/latest/download/LoongArch-Vol1-v1.02-CN.pdf (in Chinese)
|
|
|
|
https://github.com/loongson/LoongArch-Documentation/releases/latest/download/LoongArch-Vol1-v1.02-EN.pdf (in English)
|
|
|
|
Documentation of LoongArch ELF psABI:
|
|
|
|
https://github.com/loongson/LoongArch-Documentation/releases/latest/download/LoongArch-ELF-ABI-v2.00-CN.pdf (in Chinese)
|
|
|
|
https://github.com/loongson/LoongArch-Documentation/releases/latest/download/LoongArch-ELF-ABI-v2.00-EN.pdf (in English)
|
|
|
|
Linux kernel repository of Loongson and LoongArch:
|
|
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson.git
|