WSL2-Linux-Kernel/drivers/pci/quirks.c

1362 строки
45 KiB
C

/*
* This file contains work-arounds for many known PCI hardware
* bugs. Devices present only on certain architectures (host
* bridges et cetera) should be handled in arch-specific code.
*
* Note: any quirks for hotpluggable devices must _NOT_ be declared __init.
*
* Copyright (c) 1999 Martin Mares <mj@ucw.cz>
*
* The bridge optimization stuff has been removed. If you really
* have a silly BIOS which is unable to set your host bridge right,
* use the PowerTweak utility (see http://powertweak.sourceforge.net).
*/
#include <linux/config.h>
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/acpi.h>
#include "pci.h"
/* Deal with broken BIOS'es that neglect to enable passive release,
which can cause problems in combination with the 82441FX/PPro MTRRs */
static void __devinit quirk_passive_release(struct pci_dev *dev)
{
struct pci_dev *d = NULL;
unsigned char dlc;
/* We have to make sure a particular bit is set in the PIIX3
ISA bridge, so we have to go out and find it. */
while ((d = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, d))) {
pci_read_config_byte(d, 0x82, &dlc);
if (!(dlc & 1<<1)) {
printk(KERN_ERR "PCI: PIIX3: Enabling Passive Release on %s\n", pci_name(d));
dlc |= 1<<1;
pci_write_config_byte(d, 0x82, dlc);
}
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release );
/* The VIA VP2/VP3/MVP3 seem to have some 'features'. There may be a workaround
but VIA don't answer queries. If you happen to have good contacts at VIA
ask them for me please -- Alan
This appears to be BIOS not version dependent. So presumably there is a
chipset level fix */
int isa_dma_bridge_buggy; /* Exported */
static void __devinit quirk_isa_dma_hangs(struct pci_dev *dev)
{
if (!isa_dma_bridge_buggy) {
isa_dma_bridge_buggy=1;
printk(KERN_INFO "Activating ISA DMA hang workarounds.\n");
}
}
/*
* Its not totally clear which chipsets are the problematic ones
* We know 82C586 and 82C596 variants are affected.
*/
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_isa_dma_hangs );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C596, quirk_isa_dma_hangs );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, quirk_isa_dma_hangs );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, quirk_isa_dma_hangs );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_1, quirk_isa_dma_hangs );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_2, quirk_isa_dma_hangs );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_3, quirk_isa_dma_hangs );
int pci_pci_problems;
/*
* Chipsets where PCI->PCI transfers vanish or hang
*/
static void __devinit quirk_nopcipci(struct pci_dev *dev)
{
if ((pci_pci_problems & PCIPCI_FAIL)==0) {
printk(KERN_INFO "Disabling direct PCI/PCI transfers.\n");
pci_pci_problems |= PCIPCI_FAIL;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5597, quirk_nopcipci );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_496, quirk_nopcipci );
/*
* Triton requires workarounds to be used by the drivers
*/
static void __devinit quirk_triton(struct pci_dev *dev)
{
if ((pci_pci_problems&PCIPCI_TRITON)==0) {
printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n");
pci_pci_problems |= PCIPCI_TRITON;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437, quirk_triton );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437VX, quirk_triton );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439, quirk_triton );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439TX, quirk_triton );
/*
* VIA Apollo KT133 needs PCI latency patch
* Made according to a windows driver based patch by George E. Breese
* see PCI Latency Adjust on http://www.viahardware.com/download/viatweak.shtm
* Also see http://www.au-ja.org/review-kt133a-1-en.phtml for
* the info on which Mr Breese based his work.
*
* Updated based on further information from the site and also on
* information provided by VIA
*/
static void __devinit quirk_vialatency(struct pci_dev *dev)
{
struct pci_dev *p;
u8 rev;
u8 busarb;
/* Ok we have a potential problem chipset here. Now see if we have
a buggy southbridge */
p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, NULL);
if (p!=NULL) {
pci_read_config_byte(p, PCI_CLASS_REVISION, &rev);
/* 0x40 - 0x4f == 686B, 0x10 - 0x2f == 686A; thanks Dan Hollis */
/* Check for buggy part revisions */
if (rev < 0x40 || rev > 0x42)
goto exit;
} else {
p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, NULL);
if (p==NULL) /* No problem parts */
goto exit;
pci_read_config_byte(p, PCI_CLASS_REVISION, &rev);
/* Check for buggy part revisions */
if (rev < 0x10 || rev > 0x12)
goto exit;
}
/*
* Ok we have the problem. Now set the PCI master grant to
* occur every master grant. The apparent bug is that under high
* PCI load (quite common in Linux of course) you can get data
* loss when the CPU is held off the bus for 3 bus master requests
* This happens to include the IDE controllers....
*
* VIA only apply this fix when an SB Live! is present but under
* both Linux and Windows this isnt enough, and we have seen
* corruption without SB Live! but with things like 3 UDMA IDE
* controllers. So we ignore that bit of the VIA recommendation..
*/
pci_read_config_byte(dev, 0x76, &busarb);
/* Set bit 4 and bi 5 of byte 76 to 0x01
"Master priority rotation on every PCI master grant */
busarb &= ~(1<<5);
busarb |= (1<<4);
pci_write_config_byte(dev, 0x76, busarb);
printk(KERN_INFO "Applying VIA southbridge workaround.\n");
exit:
pci_dev_put(p);
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency );
/*
* VIA Apollo VP3 needs ETBF on BT848/878
*/
static void __devinit quirk_viaetbf(struct pci_dev *dev)
{
if ((pci_pci_problems&PCIPCI_VIAETBF)==0) {
printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n");
pci_pci_problems |= PCIPCI_VIAETBF;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_viaetbf );
static void __devinit quirk_vsfx(struct pci_dev *dev)
{
if ((pci_pci_problems&PCIPCI_VSFX)==0) {
printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n");
pci_pci_problems |= PCIPCI_VSFX;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C576, quirk_vsfx );
/*
* Ali Magik requires workarounds to be used by the drivers
* that DMA to AGP space. Latency must be set to 0xA and triton
* workaround applied too
* [Info kindly provided by ALi]
*/
static void __init quirk_alimagik(struct pci_dev *dev)
{
if ((pci_pci_problems&PCIPCI_ALIMAGIK)==0) {
printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n");
pci_pci_problems |= PCIPCI_ALIMAGIK|PCIPCI_TRITON;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1647, quirk_alimagik );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1651, quirk_alimagik );
/*
* Natoma has some interesting boundary conditions with Zoran stuff
* at least
*/
static void __devinit quirk_natoma(struct pci_dev *dev)
{
if ((pci_pci_problems&PCIPCI_NATOMA)==0) {
printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n");
pci_pci_problems |= PCIPCI_NATOMA;
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_natoma );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_0, quirk_natoma );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_1, quirk_natoma );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_0, quirk_natoma );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_1, quirk_natoma );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_2, quirk_natoma );
/*
* This chip can cause PCI parity errors if config register 0xA0 is read
* while DMAs are occurring.
*/
static void __devinit quirk_citrine(struct pci_dev *dev)
{
dev->cfg_size = 0xA0;
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, PCI_DEVICE_ID_IBM_CITRINE, quirk_citrine );
/*
* S3 868 and 968 chips report region size equal to 32M, but they decode 64M.
* If it's needed, re-allocate the region.
*/
static void __devinit quirk_s3_64M(struct pci_dev *dev)
{
struct resource *r = &dev->resource[0];
if ((r->start & 0x3ffffff) || r->end != r->start + 0x3ffffff) {
r->start = 0;
r->end = 0x3ffffff;
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_868, quirk_s3_64M );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_968, quirk_s3_64M );
static void __devinit quirk_io_region(struct pci_dev *dev, unsigned region, unsigned size, int nr)
{
region &= ~(size-1);
if (region) {
struct resource *res = dev->resource + nr;
res->name = pci_name(dev);
res->start = region;
res->end = region + size - 1;
res->flags = IORESOURCE_IO;
pci_claim_resource(dev, nr);
}
}
/*
* ATI Northbridge setups MCE the processor if you even
* read somewhere between 0x3b0->0x3bb or read 0x3d3
*/
static void __devinit quirk_ati_exploding_mce(struct pci_dev *dev)
{
printk(KERN_INFO "ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb.\n");
/* Mae rhaid i ni beidio ag edrych ar y lleoliadiau I/O hyn */
request_region(0x3b0, 0x0C, "RadeonIGP");
request_region(0x3d3, 0x01, "RadeonIGP");
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS100, quirk_ati_exploding_mce );
/*
* Let's make the southbridge information explicit instead
* of having to worry about people probing the ACPI areas,
* for example.. (Yes, it happens, and if you read the wrong
* ACPI register it will put the machine to sleep with no
* way of waking it up again. Bummer).
*
* ALI M7101: Two IO regions pointed to by words at
* 0xE0 (64 bytes of ACPI registers)
* 0xE2 (32 bytes of SMB registers)
*/
static void __devinit quirk_ali7101_acpi(struct pci_dev *dev)
{
u16 region;
pci_read_config_word(dev, 0xE0, &region);
quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES);
pci_read_config_word(dev, 0xE2, &region);
quirk_io_region(dev, region, 32, PCI_BRIDGE_RESOURCES+1);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101, quirk_ali7101_acpi );
/*
* PIIX4 ACPI: Two IO regions pointed to by longwords at
* 0x40 (64 bytes of ACPI registers)
* 0x90 (32 bytes of SMB registers)
*/
static void __devinit quirk_piix4_acpi(struct pci_dev *dev)
{
u32 region;
pci_read_config_dword(dev, 0x40, &region);
quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES);
pci_read_config_dword(dev, 0x90, &region);
quirk_io_region(dev, region, 32, PCI_BRIDGE_RESOURCES+1);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, quirk_piix4_acpi );
/*
* ICH4, ICH4-M, ICH5, ICH5-M ACPI: Three IO regions pointed to by longwords at
* 0x40 (128 bytes of ACPI, GPIO & TCO registers)
* 0x58 (64 bytes of GPIO I/O space)
*/
static void __devinit quirk_ich4_lpc_acpi(struct pci_dev *dev)
{
u32 region;
pci_read_config_dword(dev, 0x40, &region);
quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES);
pci_read_config_dword(dev, 0x58, &region);
quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES+1);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, quirk_ich4_lpc_acpi );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_0, quirk_ich4_lpc_acpi );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, quirk_ich4_lpc_acpi );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_10, quirk_ich4_lpc_acpi );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, quirk_ich4_lpc_acpi );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, quirk_ich4_lpc_acpi );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, quirk_ich4_lpc_acpi );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, quirk_ich4_lpc_acpi );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, quirk_ich4_lpc_acpi );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_1, quirk_ich4_lpc_acpi );
/*
* VIA ACPI: One IO region pointed to by longword at
* 0x48 or 0x20 (256 bytes of ACPI registers)
*/
static void __devinit quirk_vt82c586_acpi(struct pci_dev *dev)
{
u8 rev;
u32 region;
pci_read_config_byte(dev, PCI_CLASS_REVISION, &rev);
if (rev & 0x10) {
pci_read_config_dword(dev, 0x48, &region);
region &= PCI_BASE_ADDRESS_IO_MASK;
quirk_io_region(dev, region, 256, PCI_BRIDGE_RESOURCES);
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_vt82c586_acpi );
/*
* VIA VT82C686 ACPI: Three IO region pointed to by (long)words at
* 0x48 (256 bytes of ACPI registers)
* 0x70 (128 bytes of hardware monitoring register)
* 0x90 (16 bytes of SMB registers)
*/
static void __devinit quirk_vt82c686_acpi(struct pci_dev *dev)
{
u16 hm;
u32 smb;
quirk_vt82c586_acpi(dev);
pci_read_config_word(dev, 0x70, &hm);
hm &= PCI_BASE_ADDRESS_IO_MASK;
quirk_io_region(dev, hm, 128, PCI_BRIDGE_RESOURCES + 1);
pci_read_config_dword(dev, 0x90, &smb);
smb &= PCI_BASE_ADDRESS_IO_MASK;
quirk_io_region(dev, smb, 16, PCI_BRIDGE_RESOURCES + 2);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_vt82c686_acpi );
#ifdef CONFIG_X86_IO_APIC
#include <asm/io_apic.h>
/*
* VIA 686A/B: If an IO-APIC is active, we need to route all on-chip
* devices to the external APIC.
*
* TODO: When we have device-specific interrupt routers,
* this code will go away from quirks.
*/
static void __devinit quirk_via_ioapic(struct pci_dev *dev)
{
u8 tmp;
if (nr_ioapics < 1)
tmp = 0; /* nothing routed to external APIC */
else
tmp = 0x1f; /* all known bits (4-0) routed to external APIC */
printk(KERN_INFO "PCI: %sbling Via external APIC routing\n",
tmp == 0 ? "Disa" : "Ena");
/* Offset 0x58: External APIC IRQ output control */
pci_write_config_byte (dev, 0x58, tmp);
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic );
/*
* The AMD io apic can hang the box when an apic irq is masked.
* We check all revs >= B0 (yet not in the pre production!) as the bug
* is currently marked NoFix
*
* We have multiple reports of hangs with this chipset that went away with
* noapic specified. For the moment we assume its the errata. We may be wrong
* of course. However the advice is demonstrably good even if so..
*/
static void __devinit quirk_amd_ioapic(struct pci_dev *dev)
{
u8 rev;
pci_read_config_byte(dev, PCI_REVISION_ID, &rev);
if (rev >= 0x02) {
printk(KERN_WARNING "I/O APIC: AMD Errata #22 may be present. In the event of instability try\n");
printk(KERN_WARNING " : booting with the \"noapic\" option.\n");
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7410, quirk_amd_ioapic );
static void __init quirk_ioapic_rmw(struct pci_dev *dev)
{
if (dev->devfn == 0 && dev->bus->number == 0)
sis_apic_bug = 1;
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_ANY_ID, quirk_ioapic_rmw );
int pci_msi_quirk;
#define AMD8131_revA0 0x01
#define AMD8131_revB0 0x11
#define AMD8131_MISC 0x40
#define AMD8131_NIOAMODE_BIT 0
static void __init quirk_amd_8131_ioapic(struct pci_dev *dev)
{
unsigned char revid, tmp;
pci_msi_quirk = 1;
printk(KERN_WARNING "PCI: MSI quirk detected. pci_msi_quirk set.\n");
if (nr_ioapics == 0)
return;
pci_read_config_byte(dev, PCI_REVISION_ID, &revid);
if (revid == AMD8131_revA0 || revid == AMD8131_revB0) {
printk(KERN_INFO "Fixing up AMD8131 IOAPIC mode\n");
pci_read_config_byte( dev, AMD8131_MISC, &tmp);
tmp &= ~(1 << AMD8131_NIOAMODE_BIT);
pci_write_config_byte( dev, AMD8131_MISC, tmp);
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_APIC, quirk_amd_8131_ioapic );
static void __init quirk_svw_msi(struct pci_dev *dev)
{
pci_msi_quirk = 1;
printk(KERN_WARNING "PCI: MSI quirk detected. pci_msi_quirk set.\n");
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_GCNB_LE, quirk_svw_msi );
#endif /* CONFIG_X86_IO_APIC */
/*
* FIXME: it is questionable that quirk_via_acpi
* is needed. It shows up as an ISA bridge, and does not
* support the PCI_INTERRUPT_LINE register at all. Therefore
* it seems like setting the pci_dev's 'irq' to the
* value of the ACPI SCI interrupt is only done for convenience.
* -jgarzik
*/
static void __devinit quirk_via_acpi(struct pci_dev *d)
{
/*
* VIA ACPI device: SCI IRQ line in PCI config byte 0x42
*/
u8 irq;
pci_read_config_byte(d, 0x42, &irq);
irq &= 0xf;
if (irq && (irq != 2))
d->irq = irq;
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_acpi );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_acpi );
/*
* Via 686A/B: The PCI_INTERRUPT_LINE register for the on-chip
* devices, USB0/1, AC97, MC97, and ACPI, has an unusual feature:
* when written, it makes an internal connection to the PIC.
* For these devices, this register is defined to be 4 bits wide.
* Normally this is fine. However for IO-APIC motherboards, or
* non-x86 architectures (yes Via exists on PPC among other places),
* we must mask the PCI_INTERRUPT_LINE value versus 0xf to get
* interrupts delivered properly.
*/
static void quirk_via_irq(struct pci_dev *dev)
{
u8 irq, new_irq;
new_irq = dev->irq & 0xf;
pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq);
if (new_irq != irq) {
printk(KERN_INFO "PCI: Via IRQ fixup for %s, from %d to %d\n",
pci_name(dev), irq, new_irq);
udelay(15); /* unknown if delay really needed */
pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq);
}
}
DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irq);
/*
* PIIX3 USB: We have to disable USB interrupts that are
* hardwired to PIRQD# and may be shared with an
* external device.
*
* Legacy Support Register (LEGSUP):
* bit13: USB PIRQ Enable (USBPIRQDEN),
* bit4: Trap/SMI On IRQ Enable (USBSMIEN).
*
* We mask out all r/wc bits, too.
*/
static void __devinit quirk_piix3_usb(struct pci_dev *dev)
{
u16 legsup;
pci_read_config_word(dev, 0xc0, &legsup);
legsup &= 0x50ef;
pci_write_config_word(dev, 0xc0, legsup);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_2, quirk_piix3_usb );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_2, quirk_piix3_usb );
/*
* VIA VT82C598 has its device ID settable and many BIOSes
* set it to the ID of VT82C597 for backward compatibility.
* We need to switch it off to be able to recognize the real
* type of the chip.
*/
static void __devinit quirk_vt82c598_id(struct pci_dev *dev)
{
pci_write_config_byte(dev, 0xfc, 0);
pci_read_config_word(dev, PCI_DEVICE_ID, &dev->device);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_vt82c598_id );
/*
* CardBus controllers have a legacy base address that enables them
* to respond as i82365 pcmcia controllers. We don't want them to
* do this even if the Linux CardBus driver is not loaded, because
* the Linux i82365 driver does not (and should not) handle CardBus.
*/
static void __devinit quirk_cardbus_legacy(struct pci_dev *dev)
{
if ((PCI_CLASS_BRIDGE_CARDBUS << 8) ^ dev->class)
return;
pci_write_config_dword(dev, PCI_CB_LEGACY_MODE_BASE, 0);
}
DECLARE_PCI_FIXUP_FINAL(PCI_ANY_ID, PCI_ANY_ID, quirk_cardbus_legacy);
/*
* Following the PCI ordering rules is optional on the AMD762. I'm not
* sure what the designers were smoking but let's not inhale...
*
* To be fair to AMD, it follows the spec by default, its BIOS people
* who turn it off!
*/
static void __devinit quirk_amd_ordering(struct pci_dev *dev)
{
u32 pcic;
pci_read_config_dword(dev, 0x4C, &pcic);
if ((pcic&6)!=6) {
pcic |= 6;
printk(KERN_WARNING "BIOS failed to enable PCI standards compliance, fixing this error.\n");
pci_write_config_dword(dev, 0x4C, pcic);
pci_read_config_dword(dev, 0x84, &pcic);
pcic |= (1<<23); /* Required in this mode */
pci_write_config_dword(dev, 0x84, pcic);
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering );
/*
* DreamWorks provided workaround for Dunord I-3000 problem
*
* This card decodes and responds to addresses not apparently
* assigned to it. We force a larger allocation to ensure that
* nothing gets put too close to it.
*/
static void __devinit quirk_dunord ( struct pci_dev * dev )
{
struct resource *r = &dev->resource [1];
r->start = 0;
r->end = 0xffffff;
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_DUNORD, PCI_DEVICE_ID_DUNORD_I3000, quirk_dunord );
/*
* i82380FB mobile docking controller: its PCI-to-PCI bridge
* is subtractive decoding (transparent), and does indicate this
* in the ProgIf. Unfortunately, the ProgIf value is wrong - 0x80
* instead of 0x01.
*/
static void __devinit quirk_transparent_bridge(struct pci_dev *dev)
{
dev->transparent = 1;
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82380FB, quirk_transparent_bridge );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA, 0x605, quirk_transparent_bridge );
/*
* Common misconfiguration of the MediaGX/Geode PCI master that will
* reduce PCI bandwidth from 70MB/s to 25MB/s. See the GXM/GXLV/GX1
* datasheets found at http://www.national.com/ds/GX for info on what
* these bits do. <christer@weinigel.se>
*/
static void __init quirk_mediagx_master(struct pci_dev *dev)
{
u8 reg;
pci_read_config_byte(dev, 0x41, &reg);
if (reg & 2) {
reg &= ~2;
printk(KERN_INFO "PCI: Fixup for MediaGX/Geode Slave Disconnect Boundary (0x41=0x%02x)\n", reg);
pci_write_config_byte(dev, 0x41, reg);
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master );
/*
* As per PCI spec, ignore base address registers 0-3 of the IDE controllers
* running in Compatible mode (bits 0 and 2 in the ProgIf for primary and
* secondary channels respectively). If the device reports Compatible mode
* but does use BAR0-3 for address decoding, we assume that firmware has
* programmed these BARs with standard values (0x1f0,0x3f4 and 0x170,0x374).
* Exceptions (if they exist) must be handled in chip/architecture specific
* fixups.
*
* Note: for non x86 people. You may need an arch specific quirk to handle
* moving IDE devices to native mode as well. Some plug in card devices power
* up in compatible mode and assume the BIOS will adjust them.
*
* Q: should we load the 0x1f0,0x3f4 into the registers or zap them as
* we do now ? We don't want is pci_enable_device to come along
* and assign new resources. Both approaches work for that.
*/
static void __devinit quirk_ide_bases(struct pci_dev *dev)
{
struct resource *res;
int first_bar = 2, last_bar = 0;
if ((dev->class >> 8) != PCI_CLASS_STORAGE_IDE)
return;
res = &dev->resource[0];
/* primary channel: ProgIf bit 0, BAR0, BAR1 */
if (!(dev->class & 1) && (res[0].flags || res[1].flags)) {
res[0].start = res[0].end = res[0].flags = 0;
res[1].start = res[1].end = res[1].flags = 0;
first_bar = 0;
last_bar = 1;
}
/* secondary channel: ProgIf bit 2, BAR2, BAR3 */
if (!(dev->class & 4) && (res[2].flags || res[3].flags)) {
res[2].start = res[2].end = res[2].flags = 0;
res[3].start = res[3].end = res[3].flags = 0;
last_bar = 3;
}
if (!last_bar)
return;
printk(KERN_INFO "PCI: Ignoring BAR%d-%d of IDE controller %s\n",
first_bar, last_bar, pci_name(dev));
}
DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_ide_bases);
/*
* Ensure C0 rev restreaming is off. This is normally done by
* the BIOS but in the odd case it is not the results are corruption
* hence the presence of a Linux check
*/
static void __init quirk_disable_pxb(struct pci_dev *pdev)
{
u16 config;
u8 rev;
pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
if (rev != 0x04) /* Only C0 requires this */
return;
pci_read_config_word(pdev, 0x40, &config);
if (config & (1<<6)) {
config &= ~(1<<6);
pci_write_config_word(pdev, 0x40, config);
printk(KERN_INFO "PCI: C0 revision 450NX. Disabling PCI restreaming.\n");
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb );
/*
* Serverworks CSB5 IDE does not fully support native mode
*/
static void __devinit quirk_svwks_csb5ide(struct pci_dev *pdev)
{
u8 prog;
pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog);
if (prog & 5) {
prog &= ~5;
pdev->class &= ~5;
pci_write_config_byte(pdev, PCI_CLASS_PROG, prog);
/* need to re-assign BARs for compat mode */
quirk_ide_bases(pdev);
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, quirk_svwks_csb5ide );
/*
* Intel 82801CAM ICH3-M datasheet says IDE modes must be the same
*/
static void __init quirk_ide_samemode(struct pci_dev *pdev)
{
u8 prog;
pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog);
if (((prog & 1) && !(prog & 4)) || ((prog & 4) && !(prog & 1))) {
printk(KERN_INFO "PCI: IDE mode mismatch; forcing legacy mode\n");
prog &= ~5;
pdev->class &= ~5;
pci_write_config_byte(pdev, PCI_CLASS_PROG, prog);
/* need to re-assign BARs for compat mode */
quirk_ide_bases(pdev);
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, quirk_ide_samemode);
/* This was originally an Alpha specific thing, but it really fits here.
* The i82375 PCI/EISA bridge appears as non-classified. Fix that.
*/
static void __init quirk_eisa_bridge(struct pci_dev *dev)
{
dev->class = PCI_CLASS_BRIDGE_EISA << 8;
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82375, quirk_eisa_bridge );
/*
* On ASUS P4B boards, the SMBus PCI Device within the ICH2/4 southbridge
* is not activated. The myth is that Asus said that they do not want the
* users to be irritated by just another PCI Device in the Win98 device
* manager. (see the file prog/hotplug/README.p4b in the lm_sensors
* package 2.7.0 for details)
*
* The SMBus PCI Device can be activated by setting a bit in the ICH LPC
* bridge. Unfortunately, this device has no subvendor/subdevice ID. So it
* becomes necessary to do this tweak in two steps -- I've chosen the Host
* bridge as trigger.
*/
static int __initdata asus_hides_smbus = 0;
static void __init asus_hides_smbus_hostbridge(struct pci_dev *dev)
{
if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) {
if (dev->device == PCI_DEVICE_ID_INTEL_82845_HB)
switch(dev->subsystem_device) {
case 0x8025: /* P4B-LX */
case 0x8070: /* P4B */
case 0x8088: /* P4B533 */
case 0x1626: /* L3C notebook */
asus_hides_smbus = 1;
}
if (dev->device == PCI_DEVICE_ID_INTEL_82845G_HB)
switch(dev->subsystem_device) {
case 0x80b1: /* P4GE-V */
case 0x80b2: /* P4PE */
case 0x8093: /* P4B533-V */
asus_hides_smbus = 1;
}
if (dev->device == PCI_DEVICE_ID_INTEL_82850_HB)
switch(dev->subsystem_device) {
case 0x8030: /* P4T533 */
asus_hides_smbus = 1;
}
if (dev->device == PCI_DEVICE_ID_INTEL_7205_0)
switch (dev->subsystem_device) {
case 0x8070: /* P4G8X Deluxe */
asus_hides_smbus = 1;
}
if (dev->device == PCI_DEVICE_ID_INTEL_82855GM_HB)
switch (dev->subsystem_device) {
case 0x1751: /* M2N notebook */
case 0x1821: /* M5N notebook */
asus_hides_smbus = 1;
}
if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
switch (dev->subsystem_device) {
case 0x184b: /* W1N notebook */
case 0x186a: /* M6Ne notebook */
asus_hides_smbus = 1;
}
} else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_HP)) {
if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
switch(dev->subsystem_device) {
case 0x088C: /* HP Compaq nc8000 */
case 0x0890: /* HP Compaq nc6000 */
asus_hides_smbus = 1;
}
if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB)
switch (dev->subsystem_device) {
case 0x12bc: /* HP D330L */
asus_hides_smbus = 1;
}
} else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_TOSHIBA)) {
if (dev->device == PCI_DEVICE_ID_INTEL_82855GM_HB)
switch(dev->subsystem_device) {
case 0x0001: /* Toshiba Satellite A40 */
asus_hides_smbus = 1;
}
} else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG)) {
if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
switch(dev->subsystem_device) {
case 0xC00C: /* Samsung P35 notebook */
asus_hides_smbus = 1;
}
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845_HB, asus_hides_smbus_hostbridge );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845G_HB, asus_hides_smbus_hostbridge );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82850_HB, asus_hides_smbus_hostbridge );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB, asus_hides_smbus_hostbridge );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_7205_0, asus_hides_smbus_hostbridge );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855PM_HB, asus_hides_smbus_hostbridge );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855GM_HB, asus_hides_smbus_hostbridge );
static void __init asus_hides_smbus_lpc(struct pci_dev *dev)
{
u16 val;
if (likely(!asus_hides_smbus))
return;
pci_read_config_word(dev, 0xF2, &val);
if (val & 0x8) {
pci_write_config_word(dev, 0xF2, val & (~0x8));
pci_read_config_word(dev, 0xF2, &val);
if (val & 0x8)
printk(KERN_INFO "PCI: i801 SMBus device continues to play 'hide and seek'! 0x%x\n", val);
else
printk(KERN_INFO "PCI: Enabled i801 SMBus device\n");
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc );
/*
* SiS 96x south bridge: BIOS typically hides SMBus device...
*/
static void __init quirk_sis_96x_smbus(struct pci_dev *dev)
{
u8 val = 0;
printk(KERN_INFO "Enabling SiS 96x SMBus.\n");
pci_read_config_byte(dev, 0x77, &val);
pci_write_config_byte(dev, 0x77, val & ~0x10);
pci_read_config_byte(dev, 0x77, &val);
}
#define UHCI_USBLEGSUP 0xc0 /* legacy support */
#define UHCI_USBCMD 0 /* command register */
#define UHCI_USBSTS 2 /* status register */
#define UHCI_USBINTR 4 /* interrupt register */
#define UHCI_USBLEGSUP_DEFAULT 0x2000 /* only PIRQ enable set */
#define UHCI_USBCMD_RUN (1 << 0) /* RUN/STOP bit */
#define UHCI_USBCMD_GRESET (1 << 2) /* Global reset */
#define UHCI_USBCMD_CONFIGURE (1 << 6) /* config semaphore */
#define UHCI_USBSTS_HALTED (1 << 5) /* HCHalted bit */
#define OHCI_CONTROL 0x04
#define OHCI_CMDSTATUS 0x08
#define OHCI_INTRSTATUS 0x0c
#define OHCI_INTRENABLE 0x10
#define OHCI_INTRDISABLE 0x14
#define OHCI_OCR (1 << 3) /* ownership change request */
#define OHCI_CTRL_IR (1 << 8) /* interrupt routing */
#define OHCI_INTR_OC (1 << 30) /* ownership change */
#define EHCI_HCC_PARAMS 0x08 /* extended capabilities */
#define EHCI_USBCMD 0 /* command register */
#define EHCI_USBCMD_RUN (1 << 0) /* RUN/STOP bit */
#define EHCI_USBSTS 4 /* status register */
#define EHCI_USBSTS_HALTED (1 << 12) /* HCHalted bit */
#define EHCI_USBINTR 8 /* interrupt register */
#define EHCI_USBLEGSUP 0 /* legacy support register */
#define EHCI_USBLEGSUP_BIOS (1 << 16) /* BIOS semaphore */
#define EHCI_USBLEGSUP_OS (1 << 24) /* OS semaphore */
#define EHCI_USBLEGCTLSTS 4 /* legacy control/status */
#define EHCI_USBLEGCTLSTS_SOOE (1 << 13) /* SMI on ownership change */
int usb_early_handoff __devinitdata = 0;
static int __init usb_handoff_early(char *str)
{
usb_early_handoff = 1;
return 0;
}
__setup("usb-handoff", usb_handoff_early);
static void __devinit quirk_usb_handoff_uhci(struct pci_dev *pdev)
{
unsigned long base = 0;
int wait_time, delta;
u16 val, sts;
int i;
for (i = 0; i < PCI_ROM_RESOURCE; i++)
if ((pci_resource_flags(pdev, i) & IORESOURCE_IO)) {
base = pci_resource_start(pdev, i);
break;
}
if (!base)
return;
/*
* stop controller
*/
sts = inw(base + UHCI_USBSTS);
val = inw(base + UHCI_USBCMD);
val &= ~(u16)(UHCI_USBCMD_RUN | UHCI_USBCMD_CONFIGURE);
outw(val, base + UHCI_USBCMD);
/*
* wait while it stops if it was running
*/
if ((sts & UHCI_USBSTS_HALTED) == 0)
{
wait_time = 1000;
delta = 100;
do {
outw(0x1f, base + UHCI_USBSTS);
udelay(delta);
wait_time -= delta;
val = inw(base + UHCI_USBSTS);
if (val & UHCI_USBSTS_HALTED)
break;
} while (wait_time > 0);
}
/*
* disable interrupts & legacy support
*/
outw(0, base + UHCI_USBINTR);
outw(0x1f, base + UHCI_USBSTS);
pci_read_config_word(pdev, UHCI_USBLEGSUP, &val);
if (val & 0xbf)
pci_write_config_word(pdev, UHCI_USBLEGSUP, UHCI_USBLEGSUP_DEFAULT);
}
static void __devinit quirk_usb_handoff_ohci(struct pci_dev *pdev)
{
void __iomem *base;
int wait_time;
base = ioremap_nocache(pci_resource_start(pdev, 0),
pci_resource_len(pdev, 0));
if (base == NULL) return;
if (readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
wait_time = 500; /* 0.5 seconds */
writel(OHCI_INTR_OC, base + OHCI_INTRENABLE);
writel(OHCI_OCR, base + OHCI_CMDSTATUS);
while (wait_time > 0 &&
readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
wait_time -= 10;
msleep(10);
}
}
/*
* disable interrupts
*/
writel(~(u32)0, base + OHCI_INTRDISABLE);
writel(~(u32)0, base + OHCI_INTRSTATUS);
iounmap(base);
}
static void __devinit quirk_usb_disable_ehci(struct pci_dev *pdev)
{
int wait_time, delta;
void __iomem *base, *op_reg_base;
u32 hcc_params, val, temp;
u8 cap_length;
base = ioremap_nocache(pci_resource_start(pdev, 0),
pci_resource_len(pdev, 0));
if (base == NULL) return;
cap_length = readb(base);
op_reg_base = base + cap_length;
hcc_params = readl(base + EHCI_HCC_PARAMS);
hcc_params = (hcc_params >> 8) & 0xff;
if (hcc_params) {
pci_read_config_dword(pdev,
hcc_params + EHCI_USBLEGSUP,
&val);
if (((val & 0xff) == 1) && (val & EHCI_USBLEGSUP_BIOS)) {
/*
* Ok, BIOS is in smm mode, try to hand off...
*/
pci_read_config_dword(pdev,
hcc_params + EHCI_USBLEGCTLSTS,
&temp);
pci_write_config_dword(pdev,
hcc_params + EHCI_USBLEGCTLSTS,
temp | EHCI_USBLEGCTLSTS_SOOE);
val |= EHCI_USBLEGSUP_OS;
pci_write_config_dword(pdev,
hcc_params + EHCI_USBLEGSUP,
val);
wait_time = 500;
do {
msleep(10);
wait_time -= 10;
pci_read_config_dword(pdev,
hcc_params + EHCI_USBLEGSUP,
&val);
} while (wait_time && (val & EHCI_USBLEGSUP_BIOS));
if (!wait_time) {
/*
* well, possibly buggy BIOS...
*/
printk(KERN_WARNING "EHCI early BIOS handoff "
"failed (BIOS bug ?)\n");
pci_write_config_dword(pdev,
hcc_params + EHCI_USBLEGSUP,
EHCI_USBLEGSUP_OS);
pci_write_config_dword(pdev,
hcc_params + EHCI_USBLEGCTLSTS,
0);
}
}
}
/*
* halt EHCI & disable its interrupts in any case
*/
val = readl(op_reg_base + EHCI_USBSTS);
if ((val & EHCI_USBSTS_HALTED) == 0) {
val = readl(op_reg_base + EHCI_USBCMD);
val &= ~EHCI_USBCMD_RUN;
writel(val, op_reg_base + EHCI_USBCMD);
wait_time = 2000;
delta = 100;
do {
writel(0x3f, op_reg_base + EHCI_USBSTS);
udelay(delta);
wait_time -= delta;
val = readl(op_reg_base + EHCI_USBSTS);
if ((val == ~(u32)0) || (val & EHCI_USBSTS_HALTED)) {
break;
}
} while (wait_time > 0);
}
writel(0, op_reg_base + EHCI_USBINTR);
writel(0x3f, op_reg_base + EHCI_USBSTS);
iounmap(base);
return;
}
static void __devinit quirk_usb_early_handoff(struct pci_dev *pdev)
{
if (!usb_early_handoff)
return;
if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x00)) { /* UHCI */
quirk_usb_handoff_uhci(pdev);
} else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x10)) { /* OHCI */
quirk_usb_handoff_ohci(pdev);
} else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x20)) { /* EHCI */
quirk_usb_disable_ehci(pdev);
}
return;
}
DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_usb_early_handoff);
/*
* ... This is further complicated by the fact that some SiS96x south
* bridges pretend to be 85C503/5513 instead. In that case see if we
* spotted a compatible north bridge to make sure.
* (pci_find_device doesn't work yet)
*
* We can also enable the sis96x bit in the discovery register..
*/
static int __devinitdata sis_96x_compatible = 0;
#define SIS_DETECT_REGISTER 0x40
static void __init quirk_sis_503(struct pci_dev *dev)
{
u8 reg;
u16 devid;
pci_read_config_byte(dev, SIS_DETECT_REGISTER, &reg);
pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg | (1 << 6));
pci_read_config_word(dev, PCI_DEVICE_ID, &devid);
if (((devid & 0xfff0) != 0x0960) && (devid != 0x0018)) {
pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg);
return;
}
/* Make people aware that we changed the config.. */
printk(KERN_WARNING "Uncovering SIS%x that hid as a SIS503 (compatible=%d)\n", devid, sis_96x_compatible);
/*
* Ok, it now shows up as a 96x.. The 96x quirks are after
* the 503 quirk in the quirk table, so they'll automatically
* run and enable things like the SMBus device
*/
dev->device = devid;
}
static void __init quirk_sis_96x_compatible(struct pci_dev *dev)
{
sis_96x_compatible = 1;
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_645, quirk_sis_96x_compatible );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_646, quirk_sis_96x_compatible );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_648, quirk_sis_96x_compatible );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_650, quirk_sis_96x_compatible );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_651, quirk_sis_96x_compatible );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_735, quirk_sis_96x_compatible );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503 );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus );
#ifdef CONFIG_X86_IO_APIC
static void __init quirk_alder_ioapic(struct pci_dev *pdev)
{
int i;
if ((pdev->class >> 8) != 0xff00)
return;
/* the first BAR is the location of the IO APIC...we must
* not touch this (and it's already covered by the fixmap), so
* forcibly insert it into the resource tree */
if (pci_resource_start(pdev, 0) && pci_resource_len(pdev, 0))
insert_resource(&iomem_resource, &pdev->resource[0]);
/* The next five BARs all seem to be rubbish, so just clean
* them out */
for (i=1; i < 6; i++) {
memset(&pdev->resource[i], 0, sizeof(pdev->resource[i]));
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EESSC, quirk_alder_ioapic );
#endif
#ifdef CONFIG_SCSI_SATA
static void __devinit quirk_intel_ide_combined(struct pci_dev *pdev)
{
u8 prog, comb, tmp;
int ich = 0;
/*
* Narrow down to Intel SATA PCI devices.
*/
switch (pdev->device) {
/* PCI ids taken from drivers/scsi/ata_piix.c */
case 0x24d1:
case 0x24df:
case 0x25a3:
case 0x25b0:
ich = 5;
break;
case 0x2651:
case 0x2652:
case 0x2653:
case 0x2680: /* ESB2 */
ich = 6;
break;
case 0x27c0:
case 0x27c4:
ich = 7;
break;
default:
/* we do not handle this PCI device */
return;
}
/*
* Read combined mode register.
*/
pci_read_config_byte(pdev, 0x90, &tmp); /* combined mode reg */
if (ich == 5) {
tmp &= 0x6; /* interesting bits 2:1, PATA primary/secondary */
if (tmp == 0x4) /* bits 10x */
comb = (1 << 0); /* SATA port 0, PATA port 1 */
else if (tmp == 0x6) /* bits 11x */
comb = (1 << 2); /* PATA port 0, SATA port 1 */
else
return; /* not in combined mode */
} else {
WARN_ON((ich != 6) && (ich != 7));
tmp &= 0x3; /* interesting bits 1:0 */
if (tmp & (1 << 0))
comb = (1 << 2); /* PATA port 0, SATA port 1 */
else if (tmp & (1 << 1))
comb = (1 << 0); /* SATA port 0, PATA port 1 */
else
return; /* not in combined mode */
}
/*
* Read programming interface register.
* (Tells us if it's legacy or native mode)
*/
pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog);
/* if SATA port is in native mode, we're ok. */
if (prog & comb)
return;
/* SATA port is in legacy mode. Reserve port so that
* IDE driver does not attempt to use it. If request_region
* fails, it will be obvious at boot time, so we don't bother
* checking return values.
*/
if (comb == (1 << 0))
request_region(0x1f0, 8, "libata"); /* port 0 */
else
request_region(0x170, 8, "libata"); /* port 1 */
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, quirk_intel_ide_combined );
#endif /* CONFIG_SCSI_SATA */
int pcie_mch_quirk;
static void __devinit quirk_pcie_mch(struct pci_dev *pdev)
{
pcie_mch_quirk = 1;
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, quirk_pcie_mch );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7320_MCH, quirk_pcie_mch );
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7525_MCH, quirk_pcie_mch );
static void __devinit quirk_netmos(struct pci_dev *dev)
{
unsigned int num_parallel = (dev->subsystem_device & 0xf0) >> 4;
unsigned int num_serial = dev->subsystem_device & 0xf;
/*
* These Netmos parts are multiport serial devices with optional
* parallel ports. Even when parallel ports are present, they
* are identified as class SERIAL, which means the serial driver
* will claim them. To prevent this, mark them as class OTHER.
* These combo devices should be claimed by parport_serial.
*
* The subdevice ID is of the form 0x00PS, where <P> is the number
* of parallel ports and <S> is the number of serial ports.
*/
switch (dev->device) {
case PCI_DEVICE_ID_NETMOS_9735:
case PCI_DEVICE_ID_NETMOS_9745:
case PCI_DEVICE_ID_NETMOS_9835:
case PCI_DEVICE_ID_NETMOS_9845:
case PCI_DEVICE_ID_NETMOS_9855:
if ((dev->class >> 8) == PCI_CLASS_COMMUNICATION_SERIAL &&
num_parallel) {
printk(KERN_INFO "PCI: Netmos %04x (%u parallel, "
"%u serial); changing class SERIAL to OTHER "
"(use parport_serial)\n",
dev->device, num_parallel, num_serial);
dev->class = (PCI_CLASS_COMMUNICATION_OTHER << 8) |
(dev->class & 0xff);
}
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETMOS, PCI_ANY_ID, quirk_netmos);
static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, struct pci_fixup *end)
{
while (f < end) {
if ((f->vendor == dev->vendor || f->vendor == (u16) PCI_ANY_ID) &&
(f->device == dev->device || f->device == (u16) PCI_ANY_ID)) {
pr_debug("PCI: Calling quirk %p for %s\n", f->hook, pci_name(dev));
f->hook(dev);
}
f++;
}
}
extern struct pci_fixup __start_pci_fixups_early[];
extern struct pci_fixup __end_pci_fixups_early[];
extern struct pci_fixup __start_pci_fixups_header[];
extern struct pci_fixup __end_pci_fixups_header[];
extern struct pci_fixup __start_pci_fixups_final[];
extern struct pci_fixup __end_pci_fixups_final[];
extern struct pci_fixup __start_pci_fixups_enable[];
extern struct pci_fixup __end_pci_fixups_enable[];
void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev)
{
struct pci_fixup *start, *end;
switch(pass) {
case pci_fixup_early:
start = __start_pci_fixups_early;
end = __end_pci_fixups_early;
break;
case pci_fixup_header:
start = __start_pci_fixups_header;
end = __end_pci_fixups_header;
break;
case pci_fixup_final:
start = __start_pci_fixups_final;
end = __end_pci_fixups_final;
break;
case pci_fixup_enable:
start = __start_pci_fixups_enable;
end = __end_pci_fixups_enable;
break;
default:
/* stupid compiler warning, you would think with an enum... */
return;
}
pci_do_fixups(dev, start, end);
}
EXPORT_SYMBOL(pcie_mch_quirk);
#ifdef CONFIG_HOTPLUG
EXPORT_SYMBOL(pci_fixup_device);
#endif