WSL2-Linux-Kernel/arch/arm/boot/dts/imx27-phytec-phycard-s-som....

103 строки
2.2 KiB
Plaintext

/*
* Copyright 2012 Sascha Hauer, Uwe Kleine-König, Steffen Trumtrar
* and Markus Pargmann, Pengutronix
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/dts-v1/;
#include "imx27.dtsi"
/ {
model = "Phytec pca100";
compatible = "phytec,imx27-pca100", "fsl,imx27";
memory@a0000000 {
reg = <0xa0000000 0x08000000>; /* 128MB */
};
};
&cspi1 {
cs-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>,
<&gpio4 27 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_fec1>;
status = "okay";
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
at24@52 {
compatible = "atmel,24c32";
pagesize = <32>;
reg = <0x52>;
};
};
&iomuxc {
imx27-phycard-s-som {
pinctrl_fec1: fec1grp {
fsl,pins = <
MX27_PAD_SD3_CMD__FEC_TXD0 0x0
MX27_PAD_SD3_CLK__FEC_TXD1 0x0
MX27_PAD_ATA_DATA0__FEC_TXD2 0x0
MX27_PAD_ATA_DATA1__FEC_TXD3 0x0
MX27_PAD_ATA_DATA2__FEC_RX_ER 0x0
MX27_PAD_ATA_DATA3__FEC_RXD1 0x0
MX27_PAD_ATA_DATA4__FEC_RXD2 0x0
MX27_PAD_ATA_DATA5__FEC_RXD3 0x0
MX27_PAD_ATA_DATA6__FEC_MDIO 0x0
MX27_PAD_ATA_DATA7__FEC_MDC 0x0
MX27_PAD_ATA_DATA8__FEC_CRS 0x0
MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x0
MX27_PAD_ATA_DATA10__FEC_RXD0 0x0
MX27_PAD_ATA_DATA11__FEC_RX_DV 0x0
MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x0
MX27_PAD_ATA_DATA13__FEC_COL 0x0
MX27_PAD_ATA_DATA14__FEC_TX_ER 0x0
MX27_PAD_ATA_DATA15__FEC_TX_EN 0x0
>;
};
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX27_PAD_I2C2_SDA__I2C2_SDA 0x0
MX27_PAD_I2C2_SCL__I2C2_SCL 0x0
>;
};
pinctrl_nfc: nfcgrp {
fsl,pins = <
MX27_PAD_NFRB__NFRB 0x0
MX27_PAD_NFCLE__NFCLE 0x0
MX27_PAD_NFWP_B__NFWP_B 0x0
MX27_PAD_NFCE_B__NFCE_B 0x0
MX27_PAD_NFALE__NFALE 0x0
MX27_PAD_NFRE_B__NFRE_B 0x0
MX27_PAD_NFWE_B__NFWE_B 0x0
>;
};
};
};
&nfc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_nfc>;
nand-bus-width = <8>;
nand-ecc-mode = "hw";
nand-on-flash-bbt;
status = "okay";
};