471 строка
13 KiB
C
471 строка
13 KiB
C
/*
|
|
* Copyright (C) 1998-2000 Michel Aubry
|
|
* Copyright (C) 1998-2000 Andrzej Krzysztofowicz
|
|
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
|
|
* Copyright (C) 2007 Bartlomiej Zolnierkiewicz
|
|
* Portions copyright (c) 2001 Sun Microsystems
|
|
*
|
|
*
|
|
* RCC/ServerWorks IDE driver for Linux
|
|
*
|
|
* OSB4: `Open South Bridge' IDE Interface (fn 1)
|
|
* supports UDMA mode 2 (33 MB/s)
|
|
*
|
|
* CSB5: `Champion South Bridge' IDE Interface (fn 1)
|
|
* all revisions support UDMA mode 4 (66 MB/s)
|
|
* revision A2.0 and up support UDMA mode 5 (100 MB/s)
|
|
*
|
|
* *** The CSB5 does not provide ANY register ***
|
|
* *** to detect 80-conductor cable presence. ***
|
|
*
|
|
* CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
|
|
*
|
|
* HT1000: AKA BCM5785 - Hypertransport Southbridge for Opteron systems. IDE
|
|
* controller same as the CSB6. Single channel ATA100 only.
|
|
*
|
|
* Documentation:
|
|
* Available under NDA only. Errata info very hard to get.
|
|
*
|
|
*/
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/module.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/ide.h>
|
|
#include <linux/init.h>
|
|
|
|
#include <asm/io.h>
|
|
|
|
#define DRV_NAME "serverworks"
|
|
|
|
#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
|
|
#define SVWKS_CSB6_REVISION 0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
|
|
|
|
/* Seagate Barracuda ATA IV Family drives in UDMA mode 5
|
|
* can overrun their FIFOs when used with the CSB5 */
|
|
static const char *svwks_bad_ata100[] = {
|
|
"ST320011A",
|
|
"ST340016A",
|
|
"ST360021A",
|
|
"ST380021A",
|
|
NULL
|
|
};
|
|
|
|
static struct pci_dev *isa_dev;
|
|
|
|
static int check_in_drive_lists (ide_drive_t *drive, const char **list)
|
|
{
|
|
char *m = (char *)&drive->id[ATA_ID_PROD];
|
|
|
|
while (*list)
|
|
if (!strcmp(*list++, m))
|
|
return 1;
|
|
return 0;
|
|
}
|
|
|
|
static u8 svwks_udma_filter(ide_drive_t *drive)
|
|
{
|
|
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
|
|
u8 mask = 0;
|
|
|
|
if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE)
|
|
return 0x1f;
|
|
if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
|
|
u32 reg = 0;
|
|
if (isa_dev)
|
|
pci_read_config_dword(isa_dev, 0x64, ®);
|
|
|
|
/*
|
|
* Don't enable UDMA on disk devices for the moment
|
|
*/
|
|
if(drive->media == ide_disk)
|
|
return 0;
|
|
/* Check the OSB4 DMA33 enable bit */
|
|
return ((reg & 0x00004000) == 0x00004000) ? 0x07 : 0;
|
|
} else if (dev->revision < SVWKS_CSB5_REVISION_NEW) {
|
|
return 0x07;
|
|
} else if (dev->revision >= SVWKS_CSB5_REVISION_NEW) {
|
|
u8 btr = 0, mode;
|
|
pci_read_config_byte(dev, 0x5A, &btr);
|
|
mode = btr & 0x3;
|
|
|
|
/* If someone decides to do UDMA133 on CSB5 the same
|
|
issue will bite so be inclusive */
|
|
if (mode > 2 && check_in_drive_lists(drive, svwks_bad_ata100))
|
|
mode = 2;
|
|
|
|
switch(mode) {
|
|
case 3: mask = 0x3f; break;
|
|
case 2: mask = 0x1f; break;
|
|
case 1: mask = 0x07; break;
|
|
default: mask = 0x00; break;
|
|
}
|
|
}
|
|
if (((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
|
|
(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) &&
|
|
(!(PCI_FUNC(dev->devfn) & 1)))
|
|
mask = 0x1f;
|
|
|
|
return mask;
|
|
}
|
|
|
|
static u8 svwks_csb_check (struct pci_dev *dev)
|
|
{
|
|
switch (dev->device) {
|
|
case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
|
|
case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
|
|
case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
|
|
case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
|
|
return 1;
|
|
default:
|
|
break;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static void svwks_set_pio_mode(ide_drive_t *drive, const u8 pio)
|
|
{
|
|
static const u8 pio_modes[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
|
|
static const u8 drive_pci[] = { 0x41, 0x40, 0x43, 0x42 };
|
|
|
|
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
|
|
|
|
pci_write_config_byte(dev, drive_pci[drive->dn], pio_modes[pio]);
|
|
|
|
if (svwks_csb_check(dev)) {
|
|
u16 csb_pio = 0;
|
|
|
|
pci_read_config_word(dev, 0x4a, &csb_pio);
|
|
|
|
csb_pio &= ~(0x0f << (4 * drive->dn));
|
|
csb_pio |= (pio << (4 * drive->dn));
|
|
|
|
pci_write_config_word(dev, 0x4a, csb_pio);
|
|
}
|
|
}
|
|
|
|
static void svwks_set_dma_mode(ide_drive_t *drive, const u8 speed)
|
|
{
|
|
static const u8 udma_modes[] = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
|
|
static const u8 dma_modes[] = { 0x77, 0x21, 0x20 };
|
|
static const u8 drive_pci2[] = { 0x45, 0x44, 0x47, 0x46 };
|
|
|
|
ide_hwif_t *hwif = drive->hwif;
|
|
struct pci_dev *dev = to_pci_dev(hwif->dev);
|
|
u8 unit = drive->dn & 1;
|
|
|
|
u8 ultra_enable = 0, ultra_timing = 0, dma_timing = 0;
|
|
|
|
pci_read_config_byte(dev, (0x56|hwif->channel), &ultra_timing);
|
|
pci_read_config_byte(dev, 0x54, &ultra_enable);
|
|
|
|
ultra_timing &= ~(0x0F << (4*unit));
|
|
ultra_enable &= ~(0x01 << drive->dn);
|
|
|
|
if (speed >= XFER_UDMA_0) {
|
|
dma_timing |= dma_modes[2];
|
|
ultra_timing |= (udma_modes[speed - XFER_UDMA_0] << (4 * unit));
|
|
ultra_enable |= (0x01 << drive->dn);
|
|
} else if (speed >= XFER_MW_DMA_0)
|
|
dma_timing |= dma_modes[speed - XFER_MW_DMA_0];
|
|
|
|
pci_write_config_byte(dev, drive_pci2[drive->dn], dma_timing);
|
|
pci_write_config_byte(dev, (0x56|hwif->channel), ultra_timing);
|
|
pci_write_config_byte(dev, 0x54, ultra_enable);
|
|
}
|
|
|
|
static unsigned int init_chipset_svwks(struct pci_dev *dev)
|
|
{
|
|
unsigned int reg;
|
|
u8 btr;
|
|
|
|
/* force Master Latency Timer value to 64 PCICLKs */
|
|
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x40);
|
|
|
|
/* OSB4 : South Bridge and IDE */
|
|
if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
|
|
isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
|
|
PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
|
|
if (isa_dev) {
|
|
pci_read_config_dword(isa_dev, 0x64, ®);
|
|
reg &= ~0x00002000; /* disable 600ns interrupt mask */
|
|
if(!(reg & 0x00004000))
|
|
printk(KERN_DEBUG DRV_NAME " %s: UDMA not BIOS "
|
|
"enabled.\n", pci_name(dev));
|
|
reg |= 0x00004000; /* enable UDMA/33 support */
|
|
pci_write_config_dword(isa_dev, 0x64, reg);
|
|
}
|
|
}
|
|
|
|
/* setup CSB5/CSB6 : South Bridge and IDE option RAID */
|
|
else if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
|
|
(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
|
|
(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
|
|
|
|
/* Third Channel Test */
|
|
if (!(PCI_FUNC(dev->devfn) & 1)) {
|
|
struct pci_dev * findev = NULL;
|
|
u32 reg4c = 0;
|
|
findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
|
|
PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
|
|
if (findev) {
|
|
pci_read_config_dword(findev, 0x4C, ®4c);
|
|
reg4c &= ~0x000007FF;
|
|
reg4c |= 0x00000040;
|
|
reg4c |= 0x00000020;
|
|
pci_write_config_dword(findev, 0x4C, reg4c);
|
|
pci_dev_put(findev);
|
|
}
|
|
outb_p(0x06, 0x0c00);
|
|
dev->irq = inb_p(0x0c01);
|
|
} else {
|
|
struct pci_dev * findev = NULL;
|
|
u8 reg41 = 0;
|
|
|
|
findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
|
|
PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
|
|
if (findev) {
|
|
pci_read_config_byte(findev, 0x41, ®41);
|
|
reg41 &= ~0x40;
|
|
pci_write_config_byte(findev, 0x41, reg41);
|
|
pci_dev_put(findev);
|
|
}
|
|
/*
|
|
* This is a device pin issue on CSB6.
|
|
* Since there will be a future raid mode,
|
|
* early versions of the chipset require the
|
|
* interrupt pin to be set, and it is a compatibility
|
|
* mode issue.
|
|
*/
|
|
if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE)
|
|
dev->irq = 0;
|
|
}
|
|
// pci_read_config_dword(dev, 0x40, &pioreg)
|
|
// pci_write_config_dword(dev, 0x40, 0x99999999);
|
|
// pci_read_config_dword(dev, 0x44, &dmareg);
|
|
// pci_write_config_dword(dev, 0x44, 0xFFFFFFFF);
|
|
/* setup the UDMA Control register
|
|
*
|
|
* 1. clear bit 6 to enable DMA
|
|
* 2. enable DMA modes with bits 0-1
|
|
* 00 : legacy
|
|
* 01 : udma2
|
|
* 10 : udma2/udma4
|
|
* 11 : udma2/udma4/udma5
|
|
*/
|
|
pci_read_config_byte(dev, 0x5A, &btr);
|
|
btr &= ~0x40;
|
|
if (!(PCI_FUNC(dev->devfn) & 1))
|
|
btr |= 0x2;
|
|
else
|
|
btr |= (dev->revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
|
|
pci_write_config_byte(dev, 0x5A, btr);
|
|
}
|
|
/* Setup HT1000 SouthBridge Controller - Single Channel Only */
|
|
else if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) {
|
|
pci_read_config_byte(dev, 0x5A, &btr);
|
|
btr &= ~0x40;
|
|
btr |= 0x3;
|
|
pci_write_config_byte(dev, 0x5A, btr);
|
|
}
|
|
|
|
return dev->irq;
|
|
}
|
|
|
|
static u8 ata66_svwks_svwks(ide_hwif_t *hwif)
|
|
{
|
|
return ATA_CBL_PATA80;
|
|
}
|
|
|
|
/* On Dell PowerEdge servers with a CSB5/CSB6, the top two bits
|
|
* of the subsystem device ID indicate presence of an 80-pin cable.
|
|
* Bit 15 clear = secondary IDE channel does not have 80-pin cable.
|
|
* Bit 15 set = secondary IDE channel has 80-pin cable.
|
|
* Bit 14 clear = primary IDE channel does not have 80-pin cable.
|
|
* Bit 14 set = primary IDE channel has 80-pin cable.
|
|
*/
|
|
static u8 ata66_svwks_dell(ide_hwif_t *hwif)
|
|
{
|
|
struct pci_dev *dev = to_pci_dev(hwif->dev);
|
|
|
|
if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL &&
|
|
dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
|
|
(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE ||
|
|
dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE))
|
|
return ((1 << (hwif->channel + 14)) &
|
|
dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
|
|
return ATA_CBL_PATA40;
|
|
}
|
|
|
|
/* Sun Cobalt Alpine hardware avoids the 80-pin cable
|
|
* detect issue by attaching the drives directly to the board.
|
|
* This check follows the Dell precedent (how scary is that?!)
|
|
*
|
|
* WARNING: this only works on Alpine hardware!
|
|
*/
|
|
static u8 ata66_svwks_cobalt(ide_hwif_t *hwif)
|
|
{
|
|
struct pci_dev *dev = to_pci_dev(hwif->dev);
|
|
|
|
if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN &&
|
|
dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
|
|
dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
|
|
return ((1 << (hwif->channel + 14)) &
|
|
dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
|
|
return ATA_CBL_PATA40;
|
|
}
|
|
|
|
static u8 svwks_cable_detect(ide_hwif_t *hwif)
|
|
{
|
|
struct pci_dev *dev = to_pci_dev(hwif->dev);
|
|
|
|
/* Server Works */
|
|
if (dev->subsystem_vendor == PCI_VENDOR_ID_SERVERWORKS)
|
|
return ata66_svwks_svwks (hwif);
|
|
|
|
/* Dell PowerEdge */
|
|
if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL)
|
|
return ata66_svwks_dell (hwif);
|
|
|
|
/* Cobalt Alpine */
|
|
if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN)
|
|
return ata66_svwks_cobalt (hwif);
|
|
|
|
/* Per Specified Design by OEM, and ASIC Architect */
|
|
if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
|
|
(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2))
|
|
return ATA_CBL_PATA80;
|
|
|
|
return ATA_CBL_PATA40;
|
|
}
|
|
|
|
static const struct ide_port_ops osb4_port_ops = {
|
|
.set_pio_mode = svwks_set_pio_mode,
|
|
.set_dma_mode = svwks_set_dma_mode,
|
|
.udma_filter = svwks_udma_filter,
|
|
};
|
|
|
|
static const struct ide_port_ops svwks_port_ops = {
|
|
.set_pio_mode = svwks_set_pio_mode,
|
|
.set_dma_mode = svwks_set_dma_mode,
|
|
.udma_filter = svwks_udma_filter,
|
|
.cable_detect = svwks_cable_detect,
|
|
};
|
|
|
|
#define IDE_HFLAGS_SVWKS IDE_HFLAG_LEGACY_IRQS
|
|
|
|
static const struct ide_port_info serverworks_chipsets[] __devinitdata = {
|
|
{ /* 0: OSB4 */
|
|
.name = DRV_NAME,
|
|
.init_chipset = init_chipset_svwks,
|
|
.port_ops = &osb4_port_ops,
|
|
.host_flags = IDE_HFLAGS_SVWKS,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
.udma_mask = 0x00, /* UDMA is problematic on OSB4 */
|
|
},
|
|
{ /* 1: CSB5 */
|
|
.name = DRV_NAME,
|
|
.init_chipset = init_chipset_svwks,
|
|
.port_ops = &svwks_port_ops,
|
|
.host_flags = IDE_HFLAGS_SVWKS,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
.udma_mask = ATA_UDMA5,
|
|
},
|
|
{ /* 2: CSB6 */
|
|
.name = DRV_NAME,
|
|
.init_chipset = init_chipset_svwks,
|
|
.port_ops = &svwks_port_ops,
|
|
.host_flags = IDE_HFLAGS_SVWKS,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
.udma_mask = ATA_UDMA5,
|
|
},
|
|
{ /* 3: CSB6-2 */
|
|
.name = DRV_NAME,
|
|
.init_chipset = init_chipset_svwks,
|
|
.port_ops = &svwks_port_ops,
|
|
.host_flags = IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
.udma_mask = ATA_UDMA5,
|
|
},
|
|
{ /* 4: HT1000 */
|
|
.name = DRV_NAME,
|
|
.init_chipset = init_chipset_svwks,
|
|
.port_ops = &svwks_port_ops,
|
|
.host_flags = IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
.udma_mask = ATA_UDMA5,
|
|
}
|
|
};
|
|
|
|
/**
|
|
* svwks_init_one - called when a OSB/CSB is found
|
|
* @dev: the svwks device
|
|
* @id: the matching pci id
|
|
*
|
|
* Called when the PCI registration layer (or the IDE initialization)
|
|
* finds a device matching our IDE device tables.
|
|
*/
|
|
|
|
static int __devinit svwks_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|
{
|
|
struct ide_port_info d;
|
|
u8 idx = id->driver_data;
|
|
|
|
d = serverworks_chipsets[idx];
|
|
|
|
if (idx == 1)
|
|
d.host_flags |= IDE_HFLAG_CLEAR_SIMPLEX;
|
|
else if (idx == 2 || idx == 3) {
|
|
if ((PCI_FUNC(dev->devfn) & 1) == 0) {
|
|
if (pci_resource_start(dev, 0) != 0x01f1)
|
|
d.host_flags |= IDE_HFLAG_NON_BOOTABLE;
|
|
d.host_flags |= IDE_HFLAG_SINGLE;
|
|
} else
|
|
d.host_flags &= ~IDE_HFLAG_SINGLE;
|
|
}
|
|
|
|
return ide_pci_init_one(dev, &d, NULL);
|
|
}
|
|
|
|
static const struct pci_device_id svwks_pci_tbl[] = {
|
|
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0 },
|
|
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 1 },
|
|
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2 },
|
|
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 3 },
|
|
{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 4 },
|
|
{ 0, },
|
|
};
|
|
MODULE_DEVICE_TABLE(pci, svwks_pci_tbl);
|
|
|
|
static struct pci_driver svwks_pci_driver = {
|
|
.name = "Serverworks_IDE",
|
|
.id_table = svwks_pci_tbl,
|
|
.probe = svwks_init_one,
|
|
.remove = ide_pci_remove,
|
|
.suspend = ide_pci_suspend,
|
|
.resume = ide_pci_resume,
|
|
};
|
|
|
|
static int __init svwks_ide_init(void)
|
|
{
|
|
return ide_pci_register_driver(&svwks_pci_driver);
|
|
}
|
|
|
|
static void __exit svwks_ide_exit(void)
|
|
{
|
|
pci_unregister_driver(&svwks_pci_driver);
|
|
}
|
|
|
|
module_init(svwks_ide_init);
|
|
module_exit(svwks_ide_exit);
|
|
|
|
MODULE_AUTHOR("Michael Aubry. Andrzej Krzysztofowicz, Andre Hedrick");
|
|
MODULE_DESCRIPTION("PCI driver module for Serverworks OSB4/CSB5/CSB6 IDE");
|
|
MODULE_LICENSE("GPL");
|