ef69bc9f68
For early sections, its memmap is handled specially even sub-section is
enabled. The memmap could only be populated as a whole.
Quoted from the comment of section_activate():
* The early init code does not consider partially populated
* initial sections, it simply assumes that memory will never be
* referenced. If we hot-add memory into such a section then we
* do not need to populate the memmap and can simply reuse what
* is already there.
While current section_deactivate() breaks this rule. When hot-remove a
sub-section, section_deactivate() would depopulate its memmap. The
consequence is if we hot-add this subsection again, its memmap never get
proper populated.
We can reproduce the case by following steps:
1. Hacking qemu to allow sub-section early section
: diff --git a/hw/i386/pc.c b/hw/i386/pc.c
: index 51b3050d01..c6a78d83c0 100644
: --- a/hw/i386/pc.c
: +++ b/hw/i386/pc.c
: @@ -1010,7 +1010,7 @@ void pc_memory_init(PCMachineState *pcms,
: }
:
: machine->device_memory->base =
: - ROUND_UP(0x100000000ULL + x86ms->above_4g_mem_size, 1 * GiB);
: + 0x100000000ULL + x86ms->above_4g_mem_size;
:
: if (pcmc->enforce_aligned_dimm) {
: /* size device region assuming 1G page max alignment per slot */
2. Bootup qemu with PSE disabled and a sub-section aligned memory size
Part of the qemu command would look like this:
sudo x86_64-softmmu/qemu-system-x86_64 \
--enable-kvm -cpu host,pse=off \
-m 4160M,maxmem=20G,slots=1 \
-smp sockets=2,cores=16 \
-numa node,nodeid=0,cpus=0-1 -numa node,nodeid=1,cpus=2-3 \
-machine pc,nvdimm \
-nographic \
-object memory-backend-ram,id=mem0,size=8G \
-device nvdimm,id=vm0,memdev=mem0,node=0,addr=0x144000000,label-size=128k
3. Re-config a pmem device with sub-section size in guest
ndctl create-namespace --force --reconfig=namespace0.0 --mode=devdax --size=16M
Then you would see the following call trace:
pmem0: detected capacity change from 0 to 16777216
BUG: unable to handle page fault for address: ffffec73c51000b4
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 81ff8067 P4D 81ff8067 PUD 81ff7067 PMD 1437cb067 PTE 0
Oops: 0002 [#1] SMP NOPTI
CPU: 16 PID: 1348 Comm: ndctl Kdump: loaded Tainted: G W 5.8.0-rc2+ #24
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.4
RIP: 0010:memmap_init_zone+0x154/0x1c2
Code: 77 16 f6 40 10 02 74 10 48 03 48 08 48 89 cb 48 c1 eb 0c e9 3a ff ff ff 48 89 df 48 c1 e7 06 48f
RSP: 0018:ffffbdc7011a39b0 EFLAGS: 00010282
RAX: ffffec73c5100088 RBX: 0000000000144002 RCX: 0000000000144000
RDX: 0000000000000004 RSI: 007ffe0000000000 RDI: ffffec73c5100080
RBP: 027ffe0000000000 R08: 0000000000000001 R09: ffff9f8d38f6d708
R10: ffffec73c0000000 R11: 0000000000000000 R12: 0000000000000004
R13: 0000000000000001 R14: 0000000000144200 R15: 0000000000000000
FS: 00007efe6b65d780(0000) GS:ffff9f8d3f780000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffec73c51000b4 CR3: 000000007d718000 CR4: 0000000000340ee0
Call Trace:
move_pfn_range_to_zone+0x128/0x150
memremap_pages+0x4e4/0x5a0
devm_memremap_pages+0x1e/0x60
dev_dax_probe+0x69/0x160 [device_dax]
really_probe+0x298/0x3c0
driver_probe_device+0xe1/0x150
? driver_allows_async_probing+0x50/0x50
bus_for_each_drv+0x7e/0xc0
__device_attach+0xdf/0x160
bus_probe_device+0x8e/0xa0
device_add+0x3b9/0x740
__devm_create_dev_dax+0x127/0x1c0
__dax_pmem_probe+0x1f2/0x219 [dax_pmem_core]
dax_pmem_probe+0xc/0x1b [dax_pmem]
nvdimm_bus_probe+0x69/0x1c0 [libnvdimm]
really_probe+0x147/0x3c0
driver_probe_device+0xe1/0x150
device_driver_attach+0x53/0x60
bind_store+0xd1/0x110
kernfs_fop_write+0xce/0x1b0
vfs_write+0xb6/0x1a0
ksys_write+0x5f/0xe0
do_syscall_64+0x4d/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes:
|
||
|---|---|---|
| Documentation | ||
| LICENSES | ||
| arch | ||
| block | ||
| certs | ||
| crypto | ||
| drivers | ||
| fs | ||
| include | ||
| init | ||
| ipc | ||
| kernel | ||
| lib | ||
| mm | ||
| net | ||
| samples | ||
| scripts | ||
| security | ||
| sound | ||
| tools | ||
| usr | ||
| virt | ||
| .clang-format | ||
| .cocciconfig | ||
| .get_maintainer.ignore | ||
| .gitattributes | ||
| .gitignore | ||
| .mailmap | ||
| COPYING | ||
| CREDITS | ||
| Kbuild | ||
| Kconfig | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
README
Linux kernel
============
There are several guides for kernel developers and users. These guides can
be rendered in a number of formats, like HTML and PDF. Please read
Documentation/admin-guide/README.rst first.
In order to build the documentation, use ``make htmldocs`` or
``make pdfdocs``. The formatted documentation can also be read online at:
https://www.kernel.org/doc/html/latest/
There are various text files in the Documentation/ subdirectory,
several of them using the Restructured Text markup notation.
Please read the Documentation/process/changes.rst file, as it contains the
requirements for building and running the kernel, and information about
the problems which may result by upgrading your kernel.