208 строки
8.4 KiB
ReStructuredText
208 строки
8.4 KiB
ReStructuredText
===========================
|
|
SoundWire Subsystem Summary
|
|
===========================
|
|
|
|
SoundWire is a new interface ratified in 2015 by the MIPI Alliance.
|
|
SoundWire is used for transporting data typically related to audio
|
|
functions. SoundWire interface is optimized to integrate audio devices in
|
|
mobile or mobile inspired systems.
|
|
|
|
SoundWire is a 2-pin multi-drop interface with data and clock line. It
|
|
facilitates development of low cost, efficient, high performance systems.
|
|
Broad level key features of SoundWire interface include:
|
|
|
|
(1) Transporting all of payload data channels, control information, and setup
|
|
commands over a single two-pin interface.
|
|
|
|
(2) Lower clock frequency, and hence lower power consumption, by use of DDR
|
|
(Dual Data Rate) data transmission.
|
|
|
|
(3) Clock scaling and optional multiple data lanes to give wide flexibility
|
|
in data rate to match system requirements.
|
|
|
|
(4) Device status monitoring, including interrupt-style alerts to the Master.
|
|
|
|
The SoundWire protocol supports up to eleven Slave interfaces. All the
|
|
interfaces share the common Bus containing data and clock line. Each of the
|
|
Slaves can support up to 14 Data Ports. 13 Data Ports are dedicated to audio
|
|
transport. Data Port0 is dedicated to transport of Bulk control information,
|
|
each of the audio Data Ports (1..14) can support up to 8 Channels in
|
|
transmit or receiving mode (typically fixed direction but configurable
|
|
direction is enabled by the specification). Bandwidth restrictions to
|
|
~19.2..24.576Mbits/s don't however allow for 11*13*8 channels to be
|
|
transmitted simultaneously.
|
|
|
|
Below figure shows an example of connectivity between a SoundWire Master and
|
|
two Slave devices. ::
|
|
|
|
+---------------+ +---------------+
|
|
| | Clock Signal | |
|
|
| Master |-------+-------------------------------| Slave |
|
|
| Interface | | Data Signal | Interface 1 |
|
|
| |-------|-------+-----------------------| |
|
|
+---------------+ | | +---------------+
|
|
| |
|
|
| |
|
|
| |
|
|
+--+-------+--+
|
|
| |
|
|
| Slave |
|
|
| Interface 2 |
|
|
| |
|
|
+-------------+
|
|
|
|
|
|
Terminology
|
|
===========
|
|
|
|
The MIPI SoundWire specification uses the term 'device' to refer to a Master
|
|
or Slave interface, which of course can be confusing. In this summary and
|
|
code we use the term interface only to refer to the hardware. We follow the
|
|
Linux device model by mapping each Slave interface connected on the bus as a
|
|
device managed by a specific driver. The Linux SoundWire subsystem provides
|
|
a framework to implement a SoundWire Slave driver with an API allowing
|
|
3rd-party vendors to enable implementation-defined functionality while
|
|
common setup/configuration tasks are handled by the bus.
|
|
|
|
Bus:
|
|
Implements SoundWire Linux Bus which handles the SoundWire protocol.
|
|
Programs all the MIPI-defined Slave registers. Represents a SoundWire
|
|
Master. Multiple instances of Bus may be present in a system.
|
|
|
|
Slave:
|
|
Registers as SoundWire Slave device (Linux Device). Multiple Slave devices
|
|
can register to a Bus instance.
|
|
|
|
Slave driver:
|
|
Driver controlling the Slave device. MIPI-specified registers are controlled
|
|
directly by the Bus (and transmitted through the Master driver/interface).
|
|
Any implementation-defined Slave register is controlled by Slave driver. In
|
|
practice, it is expected that the Slave driver relies on regmap and does not
|
|
request direct register access.
|
|
|
|
Programming interfaces (SoundWire Master interface Driver)
|
|
==========================================================
|
|
|
|
SoundWire Bus supports programming interfaces for the SoundWire Master
|
|
implementation and SoundWire Slave devices. All the code uses the "sdw"
|
|
prefix commonly used by SoC designers and 3rd party vendors.
|
|
|
|
Each of the SoundWire Master interfaces needs to be registered to the Bus.
|
|
Bus implements API to read standard Master MIPI properties and also provides
|
|
callback in Master ops for Master driver to implement its own functions that
|
|
provides capabilities information. DT support is not implemented at this
|
|
time but should be trivial to add since capabilities are enabled with the
|
|
``device_property_`` API.
|
|
|
|
The Master interface along with the Master interface capabilities are
|
|
registered based on board file, DT or ACPI.
|
|
|
|
Following is the Bus API to register the SoundWire Bus:
|
|
|
|
.. code-block:: c
|
|
|
|
int sdw_add_bus_master(struct sdw_bus *bus)
|
|
{
|
|
if (!bus->dev)
|
|
return -ENODEV;
|
|
|
|
mutex_init(&bus->lock);
|
|
INIT_LIST_HEAD(&bus->slaves);
|
|
|
|
/* Check ACPI for Slave devices */
|
|
sdw_acpi_find_slaves(bus);
|
|
|
|
/* Check DT for Slave devices */
|
|
sdw_of_find_slaves(bus);
|
|
|
|
return 0;
|
|
}
|
|
|
|
This will initialize sdw_bus object for Master device. "sdw_master_ops" and
|
|
"sdw_master_port_ops" callback functions are provided to the Bus.
|
|
|
|
"sdw_master_ops" is used by Bus to control the Bus in the hardware specific
|
|
way. It includes Bus control functions such as sending the SoundWire
|
|
read/write messages on Bus, setting up clock frequency & Stream
|
|
Synchronization Point (SSP). The "sdw_master_ops" structure abstracts the
|
|
hardware details of the Master from the Bus.
|
|
|
|
"sdw_master_port_ops" is used by Bus to setup the Port parameters of the
|
|
Master interface Port. Master interface Port register map is not defined by
|
|
MIPI specification, so Bus calls the "sdw_master_port_ops" callback
|
|
function to do Port operations like "Port Prepare", "Port Transport params
|
|
set", "Port enable and disable". The implementation of the Master driver can
|
|
then perform hardware-specific configurations.
|
|
|
|
Programming interfaces (SoundWire Slave Driver)
|
|
===============================================
|
|
|
|
The MIPI specification requires each Slave interface to expose a unique
|
|
48-bit identifier, stored in 6 read-only dev_id registers. This dev_id
|
|
identifier contains vendor and part information, as well as a field enabling
|
|
to differentiate between identical components. An additional class field is
|
|
currently unused. Slave driver is written for a specific vendor and part
|
|
identifier, Bus enumerates the Slave device based on these two ids.
|
|
Slave device and driver match is done based on these two ids . Probe
|
|
of the Slave driver is called by Bus on successful match between device and
|
|
driver id. A parent/child relationship is enforced between Master and Slave
|
|
devices (the logical representation is aligned with the physical
|
|
connectivity).
|
|
|
|
The information on Master/Slave dependencies is stored in platform data,
|
|
board-file, ACPI or DT. The MIPI Software specification defines additional
|
|
link_id parameters for controllers that have multiple Master interfaces. The
|
|
dev_id registers are only unique in the scope of a link, and the link_id
|
|
unique in the scope of a controller. Both dev_id and link_id are not
|
|
necessarily unique at the system level but the parent/child information is
|
|
used to avoid ambiguity.
|
|
|
|
.. code-block:: c
|
|
|
|
static const struct sdw_device_id slave_id[] = {
|
|
SDW_SLAVE_ENTRY(0x025d, 0x700, 0),
|
|
{},
|
|
};
|
|
MODULE_DEVICE_TABLE(sdw, slave_id);
|
|
|
|
static struct sdw_driver slave_sdw_driver = {
|
|
.driver = {
|
|
.name = "slave_xxx",
|
|
.pm = &slave_runtime_pm,
|
|
},
|
|
.probe = slave_sdw_probe,
|
|
.remove = slave_sdw_remove,
|
|
.ops = &slave_slave_ops,
|
|
.id_table = slave_id,
|
|
};
|
|
|
|
|
|
For capabilities, Bus implements API to read standard Slave MIPI properties
|
|
and also provides callback in Slave ops for Slave driver to implement own
|
|
function that provides capabilities information. Bus needs to know a set of
|
|
Slave capabilities to program Slave registers and to control the Bus
|
|
reconfigurations.
|
|
|
|
Future enhancements to be done
|
|
==============================
|
|
|
|
(1) Bulk Register Access (BRA) transfers.
|
|
|
|
|
|
(2) Multiple data lane support.
|
|
|
|
Links
|
|
=====
|
|
|
|
SoundWire MIPI specification 1.1 is available at:
|
|
https://members.mipi.org/wg/All-Members/document/70290
|
|
|
|
SoundWire MIPI DisCo (Discovery and Configuration) specification is
|
|
available at:
|
|
https://www.mipi.org/specifications/mipi-disco-soundwire
|
|
|
|
(publicly accessible with registration or directly accessible to MIPI
|
|
members)
|
|
|
|
MIPI Alliance Manufacturer ID Page: mid.mipi.org
|