273 строки
9.0 KiB
Plaintext
273 строки
9.0 KiB
Plaintext
dm-dust
|
|
=======
|
|
|
|
This target emulates the behavior of bad sectors at arbitrary
|
|
locations, and the ability to enable the emulation of the failures
|
|
at an arbitrary time.
|
|
|
|
This target behaves similarly to a linear target. At a given time,
|
|
the user can send a message to the target to start failing read
|
|
requests on specific blocks (to emulate the behavior of a hard disk
|
|
drive with bad sectors).
|
|
|
|
When the failure behavior is enabled (i.e.: when the output of
|
|
"dmsetup status" displays "fail_read_on_bad_block"), reads of blocks
|
|
in the "bad block list" will fail with EIO ("Input/output error").
|
|
|
|
Writes of blocks in the "bad block list will result in the following:
|
|
|
|
1. Remove the block from the "bad block list".
|
|
2. Successfully complete the write.
|
|
|
|
This emulates the "remapped sector" behavior of a drive with bad
|
|
sectors.
|
|
|
|
Normally, a drive that is encountering bad sectors will most likely
|
|
encounter more bad sectors, at an unknown time or location.
|
|
With dm-dust, the user can use the "addbadblock" and "removebadblock"
|
|
messages to add arbitrary bad blocks at new locations, and the
|
|
"enable" and "disable" messages to modulate the state of whether the
|
|
configured "bad blocks" will be treated as bad, or bypassed.
|
|
This allows the pre-writing of test data and metadata prior to
|
|
simulating a "failure" event where bad sectors start to appear.
|
|
|
|
Table parameters:
|
|
-----------------
|
|
<device_path> <offset> <blksz>
|
|
|
|
Mandatory parameters:
|
|
<device_path>: path to the block device.
|
|
<offset>: offset to data area from start of device_path
|
|
<blksz>: block size in bytes
|
|
(minimum 512, maximum 1073741824, must be a power of 2)
|
|
|
|
Usage instructions:
|
|
-------------------
|
|
|
|
First, find the size (in 512-byte sectors) of the device to be used:
|
|
|
|
$ sudo blockdev --getsz /dev/vdb1
|
|
33552384
|
|
|
|
Create the dm-dust device:
|
|
(For a device with a block size of 512 bytes)
|
|
$ sudo dmsetup create dust1 --table '0 33552384 dust /dev/vdb1 0 512'
|
|
|
|
(For a device with a block size of 4096 bytes)
|
|
$ sudo dmsetup create dust1 --table '0 33552384 dust /dev/vdb1 0 4096'
|
|
|
|
Check the status of the read behavior ("bypass" indicates that all I/O
|
|
will be passed through to the underlying device):
|
|
$ sudo dmsetup status dust1
|
|
0 33552384 dust 252:17 bypass
|
|
|
|
$ sudo dd if=/dev/mapper/dust1 of=/dev/null bs=512 count=128 iflag=direct
|
|
128+0 records in
|
|
128+0 records out
|
|
|
|
$ sudo dd if=/dev/zero of=/dev/mapper/dust1 bs=512 count=128 oflag=direct
|
|
128+0 records in
|
|
128+0 records out
|
|
|
|
Adding and removing bad blocks:
|
|
-------------------------------
|
|
|
|
At any time (i.e.: whether the device has the "bad block" emulation
|
|
enabled or disabled), bad blocks may be added or removed from the
|
|
device via the "addbadblock" and "removebadblock" messages:
|
|
|
|
$ sudo dmsetup message dust1 0 addbadblock 60
|
|
kernel: device-mapper: dust: badblock added at block 60
|
|
|
|
$ sudo dmsetup message dust1 0 addbadblock 67
|
|
kernel: device-mapper: dust: badblock added at block 67
|
|
|
|
$ sudo dmsetup message dust1 0 addbadblock 72
|
|
kernel: device-mapper: dust: badblock added at block 72
|
|
|
|
These bad blocks will be stored in the "bad block list".
|
|
While the device is in "bypass" mode, reads and writes will succeed:
|
|
|
|
$ sudo dmsetup status dust1
|
|
0 33552384 dust 252:17 bypass
|
|
|
|
Enabling block read failures:
|
|
-----------------------------
|
|
|
|
To enable the "fail read on bad block" behavior, send the "enable" message:
|
|
|
|
$ sudo dmsetup message dust1 0 enable
|
|
kernel: device-mapper: dust: enabling read failures on bad sectors
|
|
|
|
$ sudo dmsetup status dust1
|
|
0 33552384 dust 252:17 fail_read_on_bad_block
|
|
|
|
With the device in "fail read on bad block" mode, attempting to read a
|
|
block will encounter an "Input/output error":
|
|
|
|
$ sudo dd if=/dev/mapper/dust1 of=/dev/null bs=512 count=1 skip=67 iflag=direct
|
|
dd: error reading '/dev/mapper/dust1': Input/output error
|
|
0+0 records in
|
|
0+0 records out
|
|
0 bytes copied, 0.00040651 s, 0.0 kB/s
|
|
|
|
...and writing to the bad blocks will remove the blocks from the list,
|
|
therefore emulating the "remap" behavior of hard disk drives:
|
|
|
|
$ sudo dd if=/dev/zero of=/dev/mapper/dust1 bs=512 count=128 oflag=direct
|
|
128+0 records in
|
|
128+0 records out
|
|
|
|
kernel: device-mapper: dust: block 60 removed from badblocklist by write
|
|
kernel: device-mapper: dust: block 67 removed from badblocklist by write
|
|
kernel: device-mapper: dust: block 72 removed from badblocklist by write
|
|
kernel: device-mapper: dust: block 87 removed from badblocklist by write
|
|
|
|
Bad block add/remove error handling:
|
|
------------------------------------
|
|
|
|
Attempting to add a bad block that already exists in the list will
|
|
result in an "Invalid argument" error, as well as a helpful message:
|
|
|
|
$ sudo dmsetup message dust1 0 addbadblock 88
|
|
device-mapper: message ioctl on dust1 failed: Invalid argument
|
|
kernel: device-mapper: dust: block 88 already in badblocklist
|
|
|
|
Attempting to remove a bad block that doesn't exist in the list will
|
|
result in an "Invalid argument" error, as well as a helpful message:
|
|
|
|
$ sudo dmsetup message dust1 0 removebadblock 87
|
|
device-mapper: message ioctl on dust1 failed: Invalid argument
|
|
kernel: device-mapper: dust: block 87 not found in badblocklist
|
|
|
|
Counting the number of bad blocks in the bad block list:
|
|
--------------------------------------------------------
|
|
|
|
To count the number of bad blocks configured in the device, run the
|
|
following message command:
|
|
|
|
$ sudo dmsetup message dust1 0 countbadblocks
|
|
|
|
A message will print with the number of bad blocks currently
|
|
configured on the device:
|
|
|
|
kernel: device-mapper: dust: countbadblocks: 895 badblock(s) found
|
|
|
|
Querying for specific bad blocks:
|
|
---------------------------------
|
|
|
|
To find out if a specific block is in the bad block list, run the
|
|
following message command:
|
|
|
|
$ sudo dmsetup message dust1 0 queryblock 72
|
|
|
|
The following message will print if the block is in the list:
|
|
device-mapper: dust: queryblock: block 72 found in badblocklist
|
|
|
|
The following message will print if the block is in the list:
|
|
device-mapper: dust: queryblock: block 72 not found in badblocklist
|
|
|
|
The "queryblock" message command will work in both the "enabled"
|
|
and "disabled" modes, allowing the verification of whether a block
|
|
will be treated as "bad" without having to issue I/O to the device,
|
|
or having to "enable" the bad block emulation.
|
|
|
|
Clearing the bad block list:
|
|
----------------------------
|
|
|
|
To clear the bad block list (without needing to individually run
|
|
a "removebadblock" message command for every block), run the
|
|
following message command:
|
|
|
|
$ sudo dmsetup message dust1 0 clearbadblocks
|
|
|
|
After clearing the bad block list, the following message will appear:
|
|
|
|
kernel: device-mapper: dust: clearbadblocks: badblocks cleared
|
|
|
|
If there were no bad blocks to clear, the following message will
|
|
appear:
|
|
|
|
kernel: device-mapper: dust: clearbadblocks: no badblocks found
|
|
|
|
Message commands list:
|
|
----------------------
|
|
|
|
Below is a list of the messages that can be sent to a dust device:
|
|
|
|
Operations on blocks (requires a <blknum> argument):
|
|
|
|
addbadblock <blknum>
|
|
queryblock <blknum>
|
|
removebadblock <blknum>
|
|
|
|
...where <blknum> is a block number within range of the device
|
|
(corresponding to the block size of the device.)
|
|
|
|
Single argument message commands:
|
|
|
|
countbadblocks
|
|
clearbadblocks
|
|
disable
|
|
enable
|
|
quiet
|
|
|
|
Device removal:
|
|
---------------
|
|
|
|
When finished, remove the device via the "dmsetup remove" command:
|
|
|
|
$ sudo dmsetup remove dust1
|
|
|
|
Quiet mode:
|
|
-----------
|
|
|
|
On test runs with many bad blocks, it may be desirable to avoid
|
|
excessive logging (from bad blocks added, removed, or "remapped").
|
|
This can be done by enabling "quiet mode" via the following message:
|
|
|
|
$ sudo dmsetup message dust1 0 quiet
|
|
|
|
This will suppress log messages from add / remove / removed by write
|
|
operations. Log messages from "countbadblocks" or "queryblock"
|
|
message commands will still print in quiet mode.
|
|
|
|
The status of quiet mode can be seen by running "dmsetup status":
|
|
|
|
$ sudo dmsetup status dust1
|
|
0 33552384 dust 252:17 fail_read_on_bad_block quiet
|
|
|
|
To disable quiet mode, send the "quiet" message again:
|
|
|
|
$ sudo dmsetup message dust1 0 quiet
|
|
|
|
$ sudo dmsetup status dust1
|
|
0 33552384 dust 252:17 fail_read_on_bad_block verbose
|
|
|
|
(The presence of "verbose" indicates normal logging.)
|
|
|
|
"Why not...?"
|
|
-------------
|
|
|
|
scsi_debug has a "medium error" mode that can fail reads on one
|
|
specified sector (sector 0x1234, hardcoded in the source code), but
|
|
it uses RAM for the persistent storage, which drastically decreases
|
|
the potential device size.
|
|
|
|
dm-flakey fails all I/O from all block locations at a specified time
|
|
frequency, and not a given point in time.
|
|
|
|
When a bad sector occurs on a hard disk drive, reads to that sector
|
|
are failed by the device, usually resulting in an error code of EIO
|
|
("I/O error") or ENODATA ("No data available"). However, a write to
|
|
the sector may succeed, and result in the sector becoming readable
|
|
after the device controller no longer experiences errors reading the
|
|
sector (or after a reallocation of the sector). However, there may
|
|
be bad sectors that occur on the device in the future, in a different,
|
|
unpredictable location.
|
|
|
|
This target seeks to provide a device that can exhibit the behavior
|
|
of a bad sector at a known sector location, at a known time, based
|
|
on a large storage device (at least tens of gigabytes, not occupying
|
|
system memory).
|