135 строки
5.7 KiB
C
135 строки
5.7 KiB
C
#ifndef _LINUX_XD_H
|
|
#define _LINUX_XD_H
|
|
|
|
/*
|
|
* This file contains the definitions for the IO ports and errors etc. for XT hard disk controllers (at least the DTC 5150X).
|
|
*
|
|
* Author: Pat Mackinlay, pat@it.com.au
|
|
* Date: 29/09/92
|
|
*
|
|
* Revised: 01/01/93, ...
|
|
*
|
|
* Ref: DTC 5150X Controller Specification (thanks to Kevin Fowler, kevinf@agora.rain.com)
|
|
* Also thanks to: Salvador Abreu, Dave Thaler, Risto Kankkunen and Wim Van Dorst.
|
|
*/
|
|
|
|
#include <linux/interrupt.h>
|
|
|
|
/* XT hard disk controller registers */
|
|
#define XD_DATA (xd_iobase + 0x00) /* data RW register */
|
|
#define XD_RESET (xd_iobase + 0x01) /* reset WO register */
|
|
#define XD_STATUS (xd_iobase + 0x01) /* status RO register */
|
|
#define XD_SELECT (xd_iobase + 0x02) /* select WO register */
|
|
#define XD_JUMPER (xd_iobase + 0x02) /* jumper RO register */
|
|
#define XD_CONTROL (xd_iobase + 0x03) /* DMAE/INTE WO register */
|
|
#define XD_RESERVED (xd_iobase + 0x03) /* reserved */
|
|
|
|
/* XT hard disk controller commands (incomplete list) */
|
|
#define CMD_TESTREADY 0x00 /* test drive ready */
|
|
#define CMD_RECALIBRATE 0x01 /* recalibrate drive */
|
|
#define CMD_SENSE 0x03 /* request sense */
|
|
#define CMD_FORMATDRV 0x04 /* format drive */
|
|
#define CMD_VERIFY 0x05 /* read verify */
|
|
#define CMD_FORMATTRK 0x06 /* format track */
|
|
#define CMD_FORMATBAD 0x07 /* format bad track */
|
|
#define CMD_READ 0x08 /* read */
|
|
#define CMD_WRITE 0x0A /* write */
|
|
#define CMD_SEEK 0x0B /* seek */
|
|
|
|
/* Controller specific commands */
|
|
#define CMD_DTCSETPARAM 0x0C /* set drive parameters (DTC 5150X & CX only?) */
|
|
#define CMD_DTCGETECC 0x0D /* get ecc error length (DTC 5150X only?) */
|
|
#define CMD_DTCREADBUF 0x0E /* read sector buffer (DTC 5150X only?) */
|
|
#define CMD_DTCWRITEBUF 0x0F /* write sector buffer (DTC 5150X only?) */
|
|
#define CMD_DTCREMAPTRK 0x11 /* assign alternate track (DTC 5150X only?) */
|
|
#define CMD_DTCGETPARAM 0xFB /* get drive parameters (DTC 5150X only?) */
|
|
#define CMD_DTCSETSTEP 0xFC /* set step rate (DTC 5150X only?) */
|
|
#define CMD_DTCSETGEOM 0xFE /* set geometry data (DTC 5150X only?) */
|
|
#define CMD_DTCGETGEOM 0xFF /* get geometry data (DTC 5150X only?) */
|
|
#define CMD_ST11GETGEOM 0xF8 /* get geometry data (Seagate ST11R/M only?) */
|
|
#define CMD_WDSETPARAM 0x0C /* set drive parameters (WD 1004A27X only?) */
|
|
#define CMD_XBSETPARAM 0x0C /* set drive parameters (XEBEC only?) */
|
|
|
|
/* Bits for command status byte */
|
|
#define CSB_ERROR 0x02 /* error */
|
|
#define CSB_LUN 0x20 /* logical Unit Number */
|
|
|
|
/* XT hard disk controller status bits */
|
|
#define STAT_READY 0x01 /* controller is ready */
|
|
#define STAT_INPUT 0x02 /* data flowing from controller to host */
|
|
#define STAT_COMMAND 0x04 /* controller in command phase */
|
|
#define STAT_SELECT 0x08 /* controller is selected */
|
|
#define STAT_REQUEST 0x10 /* controller requesting data */
|
|
#define STAT_INTERRUPT 0x20 /* controller requesting interrupt */
|
|
|
|
/* XT hard disk controller control bits */
|
|
#define PIO_MODE 0x00 /* control bits to set for PIO */
|
|
#define DMA_MODE 0x03 /* control bits to set for DMA & interrupt */
|
|
|
|
#define XD_MAXDRIVES 2 /* maximum 2 drives */
|
|
#define XD_TIMEOUT HZ /* 1 second timeout */
|
|
#define XD_RETRIES 4 /* maximum 4 retries */
|
|
|
|
#undef DEBUG /* define for debugging output */
|
|
|
|
#ifdef DEBUG
|
|
#define DEBUG_STARTUP /* debug driver initialisation */
|
|
#define DEBUG_OVERRIDE /* debug override geometry detection */
|
|
#define DEBUG_READWRITE /* debug each read/write command */
|
|
#define DEBUG_OTHER /* debug misc. interrupt/DMA stuff */
|
|
#define DEBUG_COMMAND /* debug each controller command */
|
|
#endif /* DEBUG */
|
|
|
|
/* this structure defines the XT drives and their types */
|
|
typedef struct {
|
|
u_char heads;
|
|
u_short cylinders;
|
|
u_char sectors;
|
|
u_char control;
|
|
int unit;
|
|
} XD_INFO;
|
|
|
|
/* this structure defines a ROM BIOS signature */
|
|
typedef struct {
|
|
unsigned int offset;
|
|
const char *string;
|
|
void (*init_controller)(unsigned int address);
|
|
void (*init_drive)(u_char drive);
|
|
const char *name;
|
|
} XD_SIGNATURE;
|
|
|
|
#ifndef MODULE
|
|
static int xd_manual_geo_init (char *command);
|
|
#endif /* MODULE */
|
|
static u_char xd_detect (u_char *controller, unsigned int *address);
|
|
static u_char xd_initdrives (void (*init_drive)(u_char drive));
|
|
|
|
static void do_xd_request (struct request_queue * q);
|
|
static int xd_ioctl (struct inode *inode,struct file *file,unsigned int cmd,unsigned long arg);
|
|
static int xd_readwrite (u_char operation,XD_INFO *disk,char *buffer,u_int block,u_int count);
|
|
static void xd_recalibrate (u_char drive);
|
|
|
|
static irqreturn_t xd_interrupt_handler(int irq, void *dev_id);
|
|
static u_char xd_setup_dma (u_char opcode,u_char *buffer,u_int count);
|
|
static u_char *xd_build (u_char *cmdblk,u_char command,u_char drive,u_char head,u_short cylinder,u_char sector,u_char count,u_char control);
|
|
static void xd_watchdog (unsigned long unused);
|
|
static inline u_char xd_waitport (u_short port,u_char flags,u_char mask,u_long timeout);
|
|
static u_int xd_command (u_char *command,u_char mode,u_char *indata,u_char *outdata,u_char *sense,u_long timeout);
|
|
|
|
/* card specific setup and geometry gathering code */
|
|
static void xd_dtc_init_controller (unsigned int address);
|
|
static void xd_dtc5150cx_init_drive (u_char drive);
|
|
static void xd_dtc_init_drive (u_char drive);
|
|
static void xd_wd_init_controller (unsigned int address);
|
|
static void xd_wd_init_drive (u_char drive);
|
|
static void xd_seagate_init_controller (unsigned int address);
|
|
static void xd_seagate_init_drive (u_char drive);
|
|
static void xd_omti_init_controller (unsigned int address);
|
|
static void xd_omti_init_drive (u_char drive);
|
|
static void xd_xebec_init_controller (unsigned int address);
|
|
static void xd_xebec_init_drive (u_char drive);
|
|
static void xd_setparam (u_char command,u_char drive,u_char heads,u_short cylinders,u_short rwrite,u_short wprecomp,u_char ecc);
|
|
static void xd_override_init_drive (u_char drive);
|
|
|
|
#endif /* _LINUX_XD_H */
|