WSL2-Linux-Kernel/arch/arm/mach-omap2/board-cm-t3517.c

307 строки
7.7 KiB
C

/*
* linux/arch/arm/mach-omap2/board-cm-t3517.c
*
* Support for the CompuLab CM-T3517 modules
*
* Copyright (C) 2010 CompuLab, Ltd.
* Author: Igor Grinberg <grinberg@compulab.co.il>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
* 02110-1301 USA
*
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/leds.h>
#include <linux/rtc-v3020.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/can/platform/ti_hecc.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <plat/board.h>
#include "common.h"
#include <plat/usb.h>
#include <plat/nand.h>
#include <plat/gpmc.h>
#include <mach/am35xx.h>
#include "mux.h"
#include "control.h"
#include "common-board-devices.h"
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
static struct gpio_led cm_t3517_leds[] = {
[0] = {
.gpio = 186,
.name = "cm-t3517:green",
.default_trigger = "heartbeat",
.active_low = 0,
},
};
static struct gpio_led_platform_data cm_t3517_led_pdata = {
.num_leds = ARRAY_SIZE(cm_t3517_leds),
.leds = cm_t3517_leds,
};
static struct platform_device cm_t3517_led_device = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &cm_t3517_led_pdata,
},
};
static void __init cm_t3517_init_leds(void)
{
platform_device_register(&cm_t3517_led_device);
}
#else
static inline void cm_t3517_init_leds(void) {}
#endif
#if defined(CONFIG_CAN_TI_HECC) || defined(CONFIG_CAN_TI_HECC_MODULE)
static struct resource cm_t3517_hecc_resources[] = {
{
.start = AM35XX_IPSS_HECC_BASE,
.end = AM35XX_IPSS_HECC_BASE + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
{
.start = INT_35XX_HECC0_IRQ,
.end = INT_35XX_HECC0_IRQ,
.flags = IORESOURCE_IRQ,
},
};
static struct ti_hecc_platform_data cm_t3517_hecc_pdata = {
.scc_hecc_offset = AM35XX_HECC_SCC_HECC_OFFSET,
.scc_ram_offset = AM35XX_HECC_SCC_RAM_OFFSET,
.hecc_ram_offset = AM35XX_HECC_RAM_OFFSET,
.mbx_offset = AM35XX_HECC_MBOX_OFFSET,
.int_line = AM35XX_HECC_INT_LINE,
.version = AM35XX_HECC_VERSION,
};
static struct platform_device cm_t3517_hecc_device = {
.name = "ti_hecc",
.id = 1,
.num_resources = ARRAY_SIZE(cm_t3517_hecc_resources),
.resource = cm_t3517_hecc_resources,
.dev = {
.platform_data = &cm_t3517_hecc_pdata,
},
};
static void cm_t3517_init_hecc(void)
{
platform_device_register(&cm_t3517_hecc_device);
}
#else
static inline void cm_t3517_init_hecc(void) {}
#endif
#if defined(CONFIG_RTC_DRV_V3020) || defined(CONFIG_RTC_DRV_V3020_MODULE)
#define RTC_IO_GPIO (153)
#define RTC_WR_GPIO (154)
#define RTC_RD_GPIO (53)
#define RTC_CS_GPIO (163)
#define RTC_CS_EN_GPIO (160)
struct v3020_platform_data cm_t3517_v3020_pdata = {
.use_gpio = 1,
.gpio_cs = RTC_CS_GPIO,
.gpio_wr = RTC_WR_GPIO,
.gpio_rd = RTC_RD_GPIO,
.gpio_io = RTC_IO_GPIO,
};
static struct platform_device cm_t3517_rtc_device = {
.name = "v3020",
.id = -1,
.dev = {
.platform_data = &cm_t3517_v3020_pdata,
}
};
static void __init cm_t3517_init_rtc(void)
{
int err;
err = gpio_request_one(RTC_CS_EN_GPIO, GPIOF_OUT_INIT_HIGH,
"rtc cs en");
if (err) {
pr_err("CM-T3517: rtc cs en gpio request failed: %d\n", err);
return;
}
platform_device_register(&cm_t3517_rtc_device);
}
#else
static inline void cm_t3517_init_rtc(void) {}
#endif
#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_EHCI_HCD_MODULE)
#define HSUSB1_RESET_GPIO (146)
#define HSUSB2_RESET_GPIO (147)
#define USB_HUB_RESET_GPIO (152)
static struct usbhs_omap_board_data cm_t3517_ehci_pdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = HSUSB1_RESET_GPIO,
.reset_gpio_port[1] = HSUSB2_RESET_GPIO,
.reset_gpio_port[2] = -EINVAL,
};
static int __init cm_t3517_init_usbh(void)
{
int err;
err = gpio_request_one(USB_HUB_RESET_GPIO, GPIOF_OUT_INIT_LOW,
"usb hub rst");
if (err) {
pr_err("CM-T3517: usb hub rst gpio request failed: %d\n", err);
} else {
udelay(10);
gpio_set_value(USB_HUB_RESET_GPIO, 1);
msleep(1);
}
usbhs_init(&cm_t3517_ehci_pdata);
return 0;
}
#else
static inline int cm_t3517_init_usbh(void)
{
return 0;
}
#endif
#if defined(CONFIG_MTD_NAND_OMAP2) || defined(CONFIG_MTD_NAND_OMAP2_MODULE)
static struct mtd_partition cm_t3517_nand_partitions[] = {
{
.name = "xloader",
.offset = 0, /* Offset = 0x00000 */
.size = 4 * NAND_BLOCK_SIZE,
.mask_flags = MTD_WRITEABLE
},
{
.name = "uboot",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
.size = 15 * NAND_BLOCK_SIZE,
},
{
.name = "uboot environment",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
.size = 2 * NAND_BLOCK_SIZE,
},
{
.name = "linux",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x2A0000 */
.size = 32 * NAND_BLOCK_SIZE,
},
{
.name = "rootfs",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x6A0000 */
.size = MTDPART_SIZ_FULL,
},
};
static struct omap_nand_platform_data cm_t3517_nand_data = {
.parts = cm_t3517_nand_partitions,
.nr_parts = ARRAY_SIZE(cm_t3517_nand_partitions),
.cs = 0,
};
static void __init cm_t3517_init_nand(void)
{
if (gpmc_nand_init(&cm_t3517_nand_data) < 0)
pr_err("CM-T3517: NAND initialization failed\n");
}
#else
static inline void cm_t3517_init_nand(void) {}
#endif
static struct omap_board_config_kernel cm_t3517_config[] __initdata = {
};
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
/* GPIO186 - Green LED */
OMAP3_MUX(SYS_CLKOUT2, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
/* RTC GPIOs: */
/* IO - GPIO153 */
OMAP3_MUX(MCBSP4_DR, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
/* WR# - GPIO154 */
OMAP3_MUX(MCBSP4_DX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
/* RD# - GPIO53 */
OMAP3_MUX(GPMC_NCS2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
/* CS# - GPIO163 */
OMAP3_MUX(UART3_CTS_RCTX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
/* CS EN - GPIO160 */
OMAP3_MUX(MCBSP_CLKS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
/* HSUSB1 RESET */
OMAP3_MUX(UART2_TX, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
/* HSUSB2 RESET */
OMAP3_MUX(UART2_RX, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
/* CM-T3517 USB HUB nRESET */
OMAP3_MUX(MCBSP4_CLKX, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif
static void __init cm_t3517_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap_serial_init();
omap_sdrc_init(NULL, NULL);
omap_board_config = cm_t3517_config;
omap_board_config_size = ARRAY_SIZE(cm_t3517_config);
cm_t3517_init_leds();
cm_t3517_init_nand();
cm_t3517_init_rtc();
cm_t3517_init_usbh();
cm_t3517_init_hecc();
}
MACHINE_START(CM_T3517, "Compulab CM-T3517")
.atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = am35xx_init_early,
.init_irq = omap3_init_irq,
.handle_irq = omap3_intc_handle_irq,
.init_machine = cm_t3517_init,
.timer = &omap3_timer,
.restart = omap_prcm_restart,
MACHINE_END