When printing an error message saying a ref was requested that we do not
have, only print that ref, rather than the ref and everything sent to us
on the same packet line (e.g. protocol support specifications).
Signed-off-by: Elijah Newren <newren@gmail.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
* js/run-command-updates:
api-run-command.txt: describe error behavior of run_command functions
run-command.c: squelch a "use before assignment" warning
receive-pack: remove unnecessary run_status report
run_command: report failure to execute the program, but optionally don't
run_command: encode deadly signal number in the return value
run_command: report system call errors instead of returning error codes
run_command: return exit code as positive value
MinGW: simplify waitpid() emulation macros
The motivation for this change is that system call failures are serious
errors that should be reported to the user, but only few callers took the
burden to decode the error codes that the functions returned into error
messages.
If at all, then only an unspecific error message was given. A prominent
example is this:
$ git upload-pack . | :
fatal: unable to run 'git-upload-pack'
In this example, git-upload-pack, the external command invoked through the
git wrapper, dies due to SIGPIPE, but the git wrapper does not bother to
report the real cause. In fact, this very error message is copied to the
syslog if git-daemon's client aborts the connection early.
With this change, system call failures are reported immediately after the
failure and only a generic failure code is returned to the caller. In the
above example the error is now to the point:
$ git upload-pack . | :
error: git-upload-pack died of signal
Note that there is no error report if the invoked program terminated with
a non-zero exit code, because it is reasonable to expect that the invoked
program has already reported an error. (But many run_command call sites
nevertheless write a generic error message.)
There was one special return code that was used to identify the case where
run_command failed because the requested program could not be exec'd. This
special case is now treated like a system call failure with errno set to
ENOENT. No error is reported in this case, because the call site in git.c
expects this as a normal result. Therefore, the callers that carefully
decoded the return value still check for this condition.
Signed-off-by: Johannes Sixt <j6t@kdbg.org>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
Offload object enumeration in upload-pack to pack-objects, but fall
back on internal revision walker for shallow interaction. Aside from
architecturally making more sense, this also leaves the door open for
pack-objects to employ a revision cache mechanism. Test t5530 updated
in order to explicitly check both enumeration methods.
Signed-off-by: Nick Edelen <sirnot@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
This patch changes every occurrence of "! git" -- with the meaning
that a git call has to gracefully fail -- into "test_must_fail git".
This is useful to
- make sure the test does not fail because of a signal,
e.g. SIGSEGV, and
- advertise the use of "test_must_fail" for new tests.
Signed-off-by: Stephan Beyer <s-beyer@gmx.net>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
Originally, test_expect_failure was designed to be the opposite
of test_expect_success, but this was a bad decision. Most tests
run a series of commands that leads to the single command that
needs to be tested, like this:
test_expect_{success,failure} 'test title' '
setup1 &&
setup2 &&
setup3 &&
what is to be tested
'
And expecting a failure exit from the whole sequence misses the
point of writing tests. Your setup$N that are supposed to
succeed may have failed without even reaching what you are
trying to test. The only valid use of test_expect_failure is to
check a trivial single command that is expected to fail, which
is a minority in tests of Porcelain-ish commands.
This large-ish patch rewrites all uses of test_expect_failure to
use test_expect_success and rewrites the condition of what is
tested, like this:
test_expect_success 'test title' '
setup1 &&
setup2 &&
setup3 &&
! this command should fail
'
test_expect_failure is redefined to serve as a reminder that
that test *should* succeed but due to a known breakage in git it
currently does not pass. So if git-foo command should create a
file 'bar' but you discovered a bug that it doesn't, you can
write a test like this:
test_expect_failure 'git-foo should create bar' '
rm -f bar &&
git foo &&
test -f bar
'
This construct acts similar to test_expect_success, but instead
of reporting "ok/FAIL" like test_expect_success does, the
outcome is reported as "FIXED/still broken".
Signed-off-by: Junio C Hamano <gitster@pobox.com>
upload-pack spawns two processes, rev-list and pack-objects, and carefully
monitors their status so that it can report failure to the remote end.
This change removes the complicated procedures on the grounds of the
following observations:
- If everything is OK, rev-list closes its output pipe end, upon which
pack-objects (which reads from the pipe) sees EOF and terminates itself,
closing its output (and error) pipes. upload-pack reads from both until
it sees EOF in both. It collects the exit codes of the child processes
(which indicate success) and terminates successfully.
- If rev-list sees an error, it closes its output and terminates with
failure. pack-objects sees EOF in its input and terminates successfully.
Again upload-pack reads its inputs until EOF. When it now collects
the exit codes of its child processes, it notices the failure of rev-list
and signals failure to the remote end.
- If pack-objects sees an error, it terminates with failure. Since this
breaks the pipe to rev-list, rev-list is killed with SIGPIPE.
upload-pack reads its input until EOF, then collects the exit codes of
the child processes, notices their failures, and signals failure to the
remote end.
- If upload-pack itself dies unexpectedly, pack-objects is killed with
SIGPIPE, and subsequently also rev-list.
The upshot of this is that precise monitoring of child processes is not
required because both terminate if either one of them dies unexpectedly.
This allows us to use finish_command() and finish_async() instead of
an explicit waitpid(2) call.
The change is smaller than it looks because most of it only reduces the
indentation of a large part of the inner loop.
Signed-off-by: Johannes Sixt <johannes.sixt@telecom.at>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
Elijah Newren
Johannes Sixt
Junio C Hamano
Nick Edelen
Nanako Shiraishi
Stephan Beyer
Johannes Sixt