Originally, test_expect_failure was designed to be the opposite
of test_expect_success, but this was a bad decision. Most tests
run a series of commands that leads to the single command that
needs to be tested, like this:
test_expect_{success,failure} 'test title' '
setup1 &&
setup2 &&
setup3 &&
what is to be tested
'
And expecting a failure exit from the whole sequence misses the
point of writing tests. Your setup$N that are supposed to
succeed may have failed without even reaching what you are
trying to test. The only valid use of test_expect_failure is to
check a trivial single command that is expected to fail, which
is a minority in tests of Porcelain-ish commands.
This large-ish patch rewrites all uses of test_expect_failure to
use test_expect_success and rewrites the condition of what is
tested, like this:
test_expect_success 'test title' '
setup1 &&
setup2 &&
setup3 &&
! this command should fail
'
test_expect_failure is redefined to serve as a reminder that
that test *should* succeed but due to a known breakage in git it
currently does not pass. So if git-foo command should create a
file 'bar' but you discovered a bug that it doesn't, you can
write a test like this:
test_expect_failure 'git-foo should create bar' '
rm -f bar &&
git foo &&
test -f bar
'
This construct acts similar to test_expect_success, but instead
of reporting "ok/FAIL" like test_expect_success does, the
outcome is reported as "FIXED/still broken".
Signed-off-by: Junio C Hamano <gitster@pobox.com>
This changes the behaviour of cloning from a repository on the
local machine, by defaulting to "-l" (use hardlinks to share
files under .git/objects) and making "-l" a no-op. A new
option, --no-hardlinks, is also added to cause file-level copy
of files under .git/objects while still avoiding the normal
"pack to pipe, then receive and index pack" network transfer
overhead. The old behaviour of local cloning without -l nor -s
is availble by specifying the source repository with the newly
introduced file:///path/to/repo.git/ syntax (i.e. "same as
network" cloning).
* With --no-hardlinks (i.e. have all .git/objects/ copied via
cpio) would not catch the source repository corruption, and
also risks corrupted recipient repository if an
alpha-particle hits memory cell while indexing and resolving
deltas. As long as the recipient is created uncorrupted, you
have a good back-up.
* same-as-network is expensive, but it would catch the breakage
of the source repository. It still risks corrupted recipient
repository due to hardware failure. As long as the recipient
is created uncorrupted, you have a good back-up.
* The new default on the same filesystem, as long as the source
repository is healthy, it is very likely that the recipient
would be, too. Also it is very cheap. You do not get any
back-up benefit, though.
None of the method is resilient against the source repository
corruption, so let's discount that from the comparison. Then
the difference with and without --no-hardlinks matters primarily
if you value the back-up benefit or not. If you want to use the
cloned repository as a back-up, then it is cheaper to do a clone
with --no-hardlinks and two git-fsck (source before clone,
recipient after clone) than same-as-network clone, especially as
you are likely to do a git-fsck on the recipient if you are so
paranoid anyway.
Which leads me to believe that being able to use file:/// is
probably a good idea, if only for testability, but probably of
little practical value. We default to hardlinked clone for
everyday use, and paranoids can use --no-hardlinks as a way to
make a back-up.
Signed-off-by: Junio C Hamano <gitster@pobox.com>
This allows transfer.unpackLimit to specify what these two
configuration variables want to set.
We would probably want to deprecate the two separate variables,
as I do not see much point in specifying them independently.
Signed-off-by: Junio C Hamano <junkio@cox.net>
This makes git-fetch over git native protocol to automatically
decide to keep the downloaded pack if the fetch results in more
than 100 objects, just like receive-pack invoked by git-push
does. This logic is disabled when --keep is explicitly given
from the command line, so that a very small clone still keeps
the downloaded pack as before.
The 100 threshold can be adjusted with fetch.unpacklimit
configuration. We might want to introduce transfer.unpacklimit
to consolidate the two unpacklimit variables, which will be a
topic for the next patch.
Signed-off-by: Junio C Hamano <junkio@cox.net>
While 'init-db' still is and probably will always remain a valid git
command for obvious backward compatibility reasons, it would be a good
idea to move shipped tools and docs to using 'init' instead.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Junio C Hamano <junkio@cox.net>
This is to adjust to:
count-objects -v: show number of packs as well.
which will break a test in this series.
Signed-off-by: Junio C Hamano <junkio@cox.net>
None of the variables seem to conflict, so local was unnecessary.
Also replaced ${var:pos:len} with the sed equivalent.
Signed-off-by: Eric Wong <normalperson@yhbt.net>
Signed-off-by: Junio C Hamano <junkio@cox.net>
Relying on eye-candy progress bar was fragile to begin with.
Run fetch-pack with -k option, and count the objects that are in
the pack that were transferred from the other end.
Signed-off-by: Junio C Hamano <junkio@cox.net>
Now pack-object is not as chatty when its stderr is not connected
to a terminal, so the test needs to be adjusted for that.
Signed-off-by: Junio C Hamano <junkio@cox.net>
This test provides a minimal example of what went wrong with the old
git-fetch-pack (and now works beautifully).
Signed-off-by: Johannes Schindelin <Johannes.Schindelin@gmx.de>
Signed-off-by: Junio C Hamano <junkio@cox.net>
Junio C Hamano
Junio C Hamano
Tom Prince
Nicolas Pitre
Johannes Schindelin
Eric Wong