Граф коммитов

7 Коммитов

Автор SHA1 Сообщение Дата
Junio C Hamano da02ca508b check_path(): allow symlinked directories to checkout-index --prefix
Merlyn noticed that Documentation/install-doc-quick.sh no longer correctly
removes old installed documents when the target directory has a leading
path that is a symlink.  It turns out that "checkout-index --prefix" was
broken by recent b6986d8 (git-checkout: be careful about untracked
symlinks, 2009-07-29).

I suspect has_symlink_leading_path() could learn the third parameter
(prefix that is allowed to be symlinked directories) to allow us to retire
a similar function has_dirs_only_path().

Another avenue of fixing this I considered was to get rid of base_dir and
base_dir_len from "struct checkout", and instead make "git checkout-index"
when run with --prefix mkdir the leading path and chdir in there.  It
might be the best longer term solution to this issue, as the base_dir
feature is used only by that rather obscure codepath as far as I know.

But at least this patch should fix this breakage.

Signed-off-by: Junio C Hamano <gitster@pobox.com>
2009-08-18 03:32:45 -07:00
Stephan Beyer d492b31caf t/: Use "test_must_fail git" instead of "! git"
This patch changes every occurrence of "! git" -- with the meaning
that a git call has to gracefully fail -- into "test_must_fail git".

This is useful to

 - make sure the test does not fail because of a signal,
   e.g. SIGSEGV, and

 - advertise the use of "test_must_fail" for new tests.

Signed-off-by: Stephan Beyer <s-beyer@gmx.net>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
2008-07-13 13:21:26 -07:00
Junio C Hamano 41ac414ea2 Sane use of test_expect_failure
Originally, test_expect_failure was designed to be the opposite
of test_expect_success, but this was a bad decision.  Most tests
run a series of commands that leads to the single command that
needs to be tested, like this:

    test_expect_{success,failure} 'test title' '
	setup1 &&
        setup2 &&
        setup3 &&
        what is to be tested
    '

And expecting a failure exit from the whole sequence misses the
point of writing tests.  Your setup$N that are supposed to
succeed may have failed without even reaching what you are
trying to test.  The only valid use of test_expect_failure is to
check a trivial single command that is expected to fail, which
is a minority in tests of Porcelain-ish commands.

This large-ish patch rewrites all uses of test_expect_failure to
use test_expect_success and rewrites the condition of what is
tested, like this:

    test_expect_success 'test title' '
	setup1 &&
        setup2 &&
        setup3 &&
        ! this command should fail
    '

test_expect_failure is redefined to serve as a reminder that
that test *should* succeed but due to a known breakage in git it
currently does not pass.  So if git-foo command should create a
file 'bar' but you discovered a bug that it doesn't, you can
write a test like this:

    test_expect_failure 'git-foo should create bar' '
        rm -f bar &&
        git foo &&
        test -f bar
    '

This construct acts similar to test_expect_success, but instead
of reporting "ok/FAIL" like test_expect_success does, the
outcome is reported as "FIXED/still broken".

Signed-off-by: Junio C Hamano <gitster@pobox.com>
2008-02-01 20:49:34 -08:00
Junio C Hamano 5be60078c9 Rewrite "git-frotz" to "git frotz"
This uses the remove-dashes target to replace "git-frotz" to "git frotz".

Signed-off-by: Junio C Hamano <gitster@pobox.com>
2007-07-02 22:52:14 -07:00
Junio C Hamano a6080a0a44 War on whitespace
This uses "git-apply --whitespace=strip" to fix whitespace errors that have
crept in to our source files over time.  There are a few files that need
to have trailing whitespaces (most notably, test vectors).  The results
still passes the test, and build result in Documentation/ area is unchanged.

Signed-off-by: Junio C Hamano <gitster@pobox.com>
2007-06-07 00:04:01 -07:00
Junio C Hamano 215a7ad1ef Big tool rename.
As promised, this is the "big tool rename" patch.  The primary differences
since 0.99.6 are:

  (1) git-*-script are no more.  The commands installed do not
      have any such suffix so users do not have to remember if
      something is implemented as a shell script or not.

  (2) Many command names with 'cache' in them are renamed with
      'index' if that is what they mean.

There are backward compatibility symblic links so that you and
Porcelains can keep using the old names, but the backward
compatibility support  is expected to be removed in the near
future.

Signed-off-by: Junio C Hamano <junkio@cox.net>
2005-09-07 17:45:20 -07:00
Petr Baudis f50c9f76ca Rename some test scripts and describe the naming convention
First digit: "family", e.g. the absolute basics and global stuff (0),
the basic db-side commands (read-tree, write-tree, commit-tree), the
basic working-tree-side commands (checkout-cache, update-cache), the
other basic commands (ls-files), the diff commands, the pull commands,
exporting commands, revision tree commands...

Second digit: the particular command we are testing

Third digit: (optionally) the particular switch or group of switches
we are testing

Freeform part: commandname-details

Described in the README.

	mv t1000-checkout-cache.sh t2000-checkout-cache-clash.sh
	mv t1001-checkout-cache.sh t2001-checkout-cache-clash.sh
	mv t0200-update-cache.sh t2010-update-cache-badpath.sh
	mv t0400-ls-files.sh t3000-ls-files-others.sh
	mv t0500-ls-files.sh t3010-ls-files-killed.sh
2005-05-15 01:34:22 +02:00