The Git CodingGuidelines prefer the $(...) construct for command
substitution instead of using the backquotes `...`.
The backquoted form is the traditional method for command
substitution, and is supported by POSIX. However, all but the
simplest uses become complicated quickly. In particular, embedded
command substitutions and/or the use of double quotes require
careful escaping with the backslash character.
The patch was generated by:
for _f in $(find . -name "*.sh")
do
perl -i -pe 'BEGIN{undef $/;} s/`(.+?)`/\$(\1)/smg' "${_f}"
done
and then carefully proof-read.
Signed-off-by: Elia Pinto <gitter.spiros@gmail.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
As 0232852b, but for the push tests instead: this avoids a start_httpd
in the middle of the file, which fails under GIT_TEST_HTTPD=false.
Note that we have to munge the test in a few ways while
moving it:
1. We drop the `test -z "$GIT_TEST_HTTPD"` check; this is
too simplistic since 83d842d, and we should let
lib-httpd.sh handle it.
2. We have to port over some of the old setup from t5538.
3. In the final test, we no longer expect the extra commit
"1" built on top of "4". This was a side effect from an
earlier test in t5538 which was not ported over.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Signed-off-by: Jeff King <peff@peff.net>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
We set the default apache port for each of the httpd tests
to the 4-digit test number of the test script. We want these
to remain unique so that the tests do not conflict with each
other when run in parallel.
Instead of doing it manually in each test script, let's just
set it from the test name at run time. This is simpler, and
is one less thing to be updated when test scripts are
renamed (e.g., when being re-rolled or when conflicting
after being merged with another topic).
Incidentally, this fixes a case where t5537 and t5538 used
the same port number (5537), and could conflict with each
other when run in parallel.
Signed-off-by: Jeff King <peff@peff.net>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
The basic 8 steps to update .git/shallow does not fully apply here
because the user may choose to accept just a few refs (while fetch
always accepts all refs). The steps are modified a bit.
1-6. same as before. After calling assign_shallow_commits_to_refs at
step 6, each shallow commit has a bitmap that marks all refs that
require it.
7. mark all "ours" shallow commits that are reachable from any
refs. We will need to do the original step 7 on them later.
8. go over all shallow commit bitmaps, mark refs that require new
shallow commits.
9. setup a strict temporary shallow file to plug all the holes, even
if it may cut some of our history short. This file is used by all
hooks. The hooks could use --shallow-file=$GIT_DIR/shallow to
overcome this and reach everything in current repo.
10. go over the new refs one by one. For each ref, do the reachability
test if it needs a shallow commit on the list from step 7. Remove
it if it's reachable from our refs. Gather all required shallow
commits, run check_everything_connected() with the new ref, then
install them to .git/shallow.
This mode is disabled by default and can be turned on with
receive.shallowupdate
Signed-off-by: Nguyễn Thái Ngọc Duy <pclouds@gmail.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
Elia Pinto
Nick Alcock
Jeff King
Nguyễn Thái Ngọc Duy