# Community Specification Template 1.0 Community Specifications are recommended to be drafted in accordance with international best practices. Doing so provides clarity, helps adoption, and also eases the transition of this specification to other standards body if so desired. Accordingly, the recommended template below is based on ISO standard drafting conventions. To help you, this guide on writing standards was produced by the ISO/TMB and is available at https://www.iso.org/iso/how-to-write-standards.pdf. A model manuscript of a draft International Standard (known as “The Rice Model”) is available at https://www.iso.org/iso/model_document-rice_model.pdf. In addition, we recommend using the key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" as described in RFC 2119 - https://tools.ietf.org/html/rfc2119 ## Title ### Version _______ ### Status (Pre-draft, Draft, Approved) © _________________ This specification is subject to the Community Specification License 1.0, available at [https://github.com/CommunitySpecification/1.0](https://github.com/CommunitySpecification/1.0).   ## Contents Foreword i Introduction i 1 Scope (mandatory) 1 2 Normative references (mandatory) 1 3 Terms and definitions (mandatory) 1 4 Clause title autonumber 1 5 Clause title 1 5.1 Subclause autonumber 1 5.1.1 Subclause autonumber 1 6 Clause title 1 Annex A (informative) Bibliography 1 ## Foreword Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. No party shall not be held responsible for identifying any or all such patent rights. Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. This document was prepared by [Insert name of group]. This second/third/… edition cancels and replaces the first/second/… edition (#####:####), which has been technically revised. The main changes compared to the previous edition are as follows: — xxx xxxxxxx xxx xxxx Known patent licensing exclusions are available in the specification’s repository’s Notices.md file. Any feedback or questions on this document should be directed to specifications repository, located at _________________. THESE MATERIALS ARE PROVIDED “AS IS.” The Contributors and Licensees expressly disclaim any warranties (express, implied, or otherwise), including implied warranties of merchantability, non-infringement, fitness for a particular purpose, or title, related to the materials. The entire risk as to implementing or otherwise using the materials is assumed by the implementer and user. IN NO EVENT WILL THE CONTRIBUTORS OR LICENSEES BE LIABLE TO ANY OTHER PARTY FOR LOST PROFITS OR ANY FORM OF INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER FROM ANY CAUSES OF ACTION OF ANY KIND WITH RESPECT TO THIS DELIVERABLE OR ITS GOVERNING AGREEMENT, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), OR OTHERWISE, AND WHETHER OR NOT THE OTHER MEMBER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Introduction Type text. ## Title (Introductory element — Main element — Part : Part title) 1 Scope (mandatory) Type text. 2 Normative references (mandatory) Two options of text (remove the inappropriate option). 1) The normative references shall be introduced by the following wording. The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO ##### #, General title — Part #: Title of part ISO ##### ##:20##, General title — Part ##: Title of part 2) If no references exist, include the following phrase below the clause title: There are no normative references in this document. 3 Terms and definitions (mandatory) Four options of text (remove the inappropriate options). 1) If all the specific terms and definitions are provided in Clause 3, use the following introductory text: For the purposes of this document, the following terms and definitions apply. 2) If reference is given to an external document, use the following introductory text: For the purposes of this document, the terms and definitions given in [external document reference xxx] apply. 3) If terms and definitions are provided in Clause 3, in addition to a reference to an external document, use the following introductory text: For the purposes of this document, the terms and definitions given in [external document reference xxx] and the following apply. 4) If there are no terms and definitions provided, use the following introductory text: No terms and definitions are listed in this document. The list below is always included after each option: ISO and IEC maintain terminological databases for use in standardization at the following addresses: — ISO Online browsing platform: available at https://www.iso.org/obp — IEC Electropedia: available at http://www.electropedia.org/ 3.1 term text of the definition Note 1 to entry: Text of the note. [SOURCE: …] 3.2 term text of the definition 4 Clause title Type text. 5 Clause title Type text. Use subclauses if required e.g. 5.1 or 5.1.1. For example: 5.1 Subclause 5.1.1 Subclause 6 Clause title Example of codes: ## Annex A (informative) Annex title e.g. Example of a figure and a table A.1 Clause title autonumber Use subclauses if required e.g. A.1.1 or A.1.1.1. For example: A.1.1 Subclause autonumber A.1.1.1 Subclause autonumber Type text. Dimensions in millimetres ## Bibliography [1] ISO ##### #, General title — Part #: Title of part [2] ISO ##### ##:20##, General title — Part ##: Title of part