Change on affects 1 pass CBR.
On key frame, temporal layer_id is reset to 0 for 1 pass CBR,
but since "layer" is reset, the svc.layer_context[layer].is_key_frame
was not correspondingly set properly.
Change-Id: I08f6da0a55ac7429ccfbaddfb7be14479e43543b
tm_predictor_4x4 is implemented with SSE2 using XMM registers.
Speed up by ~25% in ./test_intra_pred_speed.
Change-Id: I25074b78d476a2cb17f81cf654bdfd80df2070e0
Small changes to the best quality default speed trade off.
Some speedup settings are worth while even for best quality as they
have only a very small impact on quality but a significant impact on
encode time.
These changes give as much as a further 50-60% increase in encode
speed for my test animations clip with minimal impact on quality.
For this sequence these changes improve the best quality encode speed
to about the same level as good quality speed 0 in Q3 2015 whilst
retaining the large quality gain of over 1 db
For many natural videos though the quality difference from good 0
to best is much smaller.
Change-Id: I28b3840009d77e129817a78a7c41e29cb03e1132
This is simpler than the previous scheme, which tried to allocate
the CRITICAL_SECTION struct in a thread-safe manner before it
could use it to run the wrapped function in a thread-safe manner.
Change-Id: I172e5544e5f16403a3a0e5e2b9104b1292a0d786
This change alters the nature and use of exhaustive motion search.
Firstly any exhaustive search is preceded by a normal step search.
The exhaustive search is only carried out if the distortion resulting
from the step search is above a threshold value.
Secondly the simple +/- 64 exhaustive search is replaced by a
multi stage mesh based search where each stage has a range
and step/interval size. Subsequent stages use the best position from
the previous stage as the center of the search but use a reduced range
and interval size.
For example:
stage 1: Range +/- 64 interval 4
stage 2: Range +/- 32 interval 2
stage 3: Range +/- 15 interval 1
This process, especially when it follows on from a normal step
search, has shown itself to be almost as effective as a full range
exhaustive search with step 1 but greatly lowers the computational
complexity such that it can be used in some cases for speeds 0-2.
This patch also removes a double exhaustive search for sub 8x8 blocks
which also contained a bug (the two searches used different distortion
metrics).
For best quality in my test animation sequence this patch has almost
no impact on quality but improves encode speed by more than 5X.
Restricted use in good quality speeds 0-2 yields significant quality gains
on the animation test of 0.2 - 0.5 db with only a small impact on encode
speed. On most clips though the quality gain and speed impact are small.
Change-Id: Id22967a840e996e1db273f6ac4ff03f4f52d49aa
This reverts commit 380a5519cc.
This causes an assertion failure in debug_check_frame_counts() which
probably isn't valid with this change; leaving the investigation for
later now.
Change-Id: Ieda5ca811ed2fa50a0cc6935919a8d10dca996e0
This function now has an AVX intrinsics version which is about 80%
faster compared to the C implementation. This provides a 2-4% total
speed-up for encode, depending on encoding parameters. The function
utilizes 3 properties of the cost function lookup table, constructed
in 'cal_nmvjointsadcost' and 'cal_nmvsadcosts'.
For the joint cost:
- mvjointsadcost[1] == mvjointsadcost[2] == mvjointsadcost[3]
For the component costs:
- For all i: mvsadcost[0][i] == mvsadcost[1][i]
(equal per component cost)
- For all i: mvsadcost[0][i] == mvsadcost[0][-i]
(Cost function is even)
These must hold, otherwise the AVX version of the function cannot be used.
Change-Id: I6c2791d43022822a9e6ab43cd124a773946d0bdc
the return value of enabled, which may be empty, is handled by the for
loop. this avoids making an unnecessarily long command line which may
fail in certain cases.
Change-Id: Ib88ecbbe2c0f6d7debb600b4caed4884497263b1
Change is only for real-time mode, speed >= 5, and non-screen content mode.
Add bias to zero/low motion for big blocks, if noise estimation
is enabled and noise level is above threshold.
Change-Id: I3a0a4608ede6aa535bda6eca528d20f8aba738e7
Marco
James Zern
Alex Converse
Scott LaVarnway
Jian Zhou
Paul Wilkins
Zoe Liu
jackychen
Ralph Giles
Geza Lore