WSL2-Linux-Kernel/drivers/cpufreq/intel_pstate.c

1612 строки
38 KiB
C
Исходник Обычный вид История

/*
* intel_pstate.c: Native P state management for Intel processors
*
* (C) Copyright 2012 Intel Corporation
* Author: Dirk Brandewie <dirk.j.brandewie@intel.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; version 2
* of the License.
*/
#include <linux/kernel.h>
#include <linux/kernel_stat.h>
#include <linux/module.h>
#include <linux/ktime.h>
#include <linux/hrtimer.h>
#include <linux/tick.h>
#include <linux/slab.h>
#include <linux/sched.h>
#include <linux/list.h>
#include <linux/cpu.h>
#include <linux/cpufreq.h>
#include <linux/sysfs.h>
#include <linux/types.h>
#include <linux/fs.h>
#include <linux/debugfs.h>
intel_pstate: skip the driver if ACPI has power mgmt option Do not load the Intel pstate driver if the platform firmware (ACPI BIOS) supports the power management alternatives. The ACPI BIOS indicates that the OS control mode can be used if the _PSS (Performance Supported States) is defined in ACPI table. For the OS control mode, the Intel pstate driver will be loaded. HP BIOS has several power management modes (firmware, OS-control and so on). For the OS control mode in HP BIOS, the Intel p-state driver will be loaded. When the customer chooses the firmware power management in HP BIOS, the Intel p-state driver will be ignored. I put hw_vendor_info vendor_info in case other vendors (Dell, Lenovo...) have their firmware power management. Vendors should make sure their firmware power management works properly, and they can go for adding their vendor info to the variable. I have verified the patch on HP ProLiant servers. The patch worked correctly. Signed-off-by: Adrian Huang <adrianhuang0701@gmail.com> [rjw: Fixed up !CONFIG_ACPI build] [Linda Knippers: As Adrian has recently left HP, I retested the updated patch on an HP ProLiant server and verified that it is behaving correctly. When the BIOS is configured for OS control for power management, the intel_pstate driver loads as expected. When the BIOS is configured to provide the power management, the intel_pstate driver does not load and we get the pcc_cpufreq driver instead.] Signed-off-by: Linda Knippers <linda.knippers@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-10-31 19:24:05 +04:00
#include <linux/acpi.h>
x86/mm: Decouple <linux/vmalloc.h> from <asm/io.h> Nothing in <asm/io.h> uses anything from <linux/vmalloc.h>, so remove it from there and fix up the resulting build problems triggered on x86 {64|32}-bit {def|allmod|allno}configs. The breakages were triggering in places where x86 builds relied on vmalloc() facilities but did not include <linux/vmalloc.h> explicitly and relied on the implicit inclusion via <asm/io.h>. Also add: - <linux/init.h> to <linux/io.h> - <asm/pgtable_types> to <asm/io.h> ... which were two other implicit header file dependencies. Suggested-by: David Miller <davem@davemloft.net> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> [ Tidied up the changelog. ] Acked-by: David Miller <davem@davemloft.net> Acked-by: Takashi Iwai <tiwai@suse.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Vinod Koul <vinod.koul@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Anton Vorontsov <anton@enomsg.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Colin Cross <ccross@android.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: James E.J. Bottomley <JBottomley@odin.com> Cc: Jaroslav Kysela <perex@perex.cz> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Kees Cook <keescook@chromium.org> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Kristen Carlson Accardi <kristen@linux.intel.com> Cc: Len Brown <lenb@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Cc: Suma Ramars <sramars@cisco.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
2015-06-02 12:01:38 +03:00
#include <linux/vmalloc.h>
#include <trace/events/power.h>
#include <asm/div64.h>
#include <asm/msr.h>
#include <asm/cpu_device_id.h>
#include <asm/cpufeature.h>
#if IS_ENABLED(CONFIG_ACPI)
#include <acpi/processor.h>
#endif
#define BYT_RATIOS 0x66a
#define BYT_VIDS 0x66b
#define BYT_TURBO_RATIOS 0x66c
#define BYT_TURBO_VIDS 0x66d
#define FRAC_BITS 8
#define int_tofp(X) ((int64_t)(X) << FRAC_BITS)
#define fp_toint(X) ((X) >> FRAC_BITS)
static inline int32_t mul_fp(int32_t x, int32_t y)
{
return ((int64_t)x * (int64_t)y) >> FRAC_BITS;
}
intel_pstate: Fix overflow in busy_scaled due to long delay The kernel may delay interrupts for a long time which can result in timers being delayed. If this occurs the intel_pstate driver will crash with a divide by zero error: divide error: 0000 [#1] SMP Modules linked in: btrfs zlib_deflate raid6_pq xor msdos ext4 mbcache jbd2 binfmt_misc arc4 md4 nls_utf8 cifs dns_resolver tcp_lp bnep bluetooth rfkill fuse dm_service_time iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi nf_conntrack_netbios_ns nf_conntrack_broadcast nf_conntrack_ftp ip6t_rpfilter ip6t_REJECT ipt_REJECT xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw iptable_filter ip_tables intel_powerclamp coretemp vfat fat kvm_intel iTCO_wdt iTCO_vendor_support ipmi_devintf sr_mod kvm crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel cdc_ether lrw usbnet cdrom mii gf128mul glue_helper ablk_helper cryptd lpc_ich mfd_core pcspkr sb_edac edac_core ipmi_si ipmi_msghandler ioatdma wmi shpchp acpi_pad nfsd auth_rpcgss nfs_acl lockd uinput dm_multipath sunrpc xfs libcrc32c usb_storage sd_mod crc_t10dif crct10dif_common ixgbe mgag200 syscopyarea sysfillrect sysimgblt mdio drm_kms_helper ttm igb drm ptp pps_core dca i2c_algo_bit megaraid_sas i2c_core dm_mirror dm_region_hash dm_log dm_mod CPU: 113 PID: 0 Comm: swapper/113 Tainted: G W -------------- 3.10.0-229.1.2.el7.x86_64 #1 Hardware name: IBM x3950 X6 -[3837AC2]-/00FN827, BIOS -[A8E112BUS-1.00]- 08/27/2014 task: ffff880fe8abe660 ti: ffff880fe8ae4000 task.ti: ffff880fe8ae4000 RIP: 0010:[<ffffffff814a9279>] [<ffffffff814a9279>] intel_pstate_timer_func+0x179/0x3d0 RSP: 0018:ffff883fff4e3db8 EFLAGS: 00010206 RAX: 0000000027100000 RBX: ffff883fe6965100 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000010 RDI: 000000002e53632d RBP: ffff883fff4e3e20 R08: 000e6f69a5a125c0 R09: ffff883fe84ec001 R10: 0000000000000002 R11: 0000000000000005 R12: 00000000000049f5 R13: 0000000000271000 R14: 00000000000049f5 R15: 0000000000000246 FS: 0000000000000000(0000) GS:ffff883fff4e0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7668601000 CR3: 000000000190a000 CR4: 00000000001407e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Stack: ffff883fff4e3e58 ffffffff81099dc1 0000000000000086 0000000000000071 ffff883fff4f3680 0000000000000071 fbdc8a965e33afee ffffffff810b69dd ffff883fe84ec000 ffff883fe6965108 0000000000000100 ffffffff814a9100 Call Trace: <IRQ> [<ffffffff81099dc1>] ? run_posix_cpu_timers+0x51/0x840 [<ffffffff810b69dd>] ? trigger_load_balance+0x5d/0x200 [<ffffffff814a9100>] ? pid_param_set+0x130/0x130 [<ffffffff8107df56>] call_timer_fn+0x36/0x110 [<ffffffff814a9100>] ? pid_param_set+0x130/0x130 [<ffffffff8107fdcf>] run_timer_softirq+0x21f/0x320 [<ffffffff81077b2f>] __do_softirq+0xef/0x280 [<ffffffff816156dc>] call_softirq+0x1c/0x30 [<ffffffff81015d95>] do_softirq+0x65/0xa0 [<ffffffff81077ec5>] irq_exit+0x115/0x120 [<ffffffff81616355>] smp_apic_timer_interrupt+0x45/0x60 [<ffffffff81614a1d>] apic_timer_interrupt+0x6d/0x80 <EOI> [<ffffffff814a9c32>] ? cpuidle_enter_state+0x52/0xc0 [<ffffffff814a9c28>] ? cpuidle_enter_state+0x48/0xc0 [<ffffffff814a9d65>] cpuidle_idle_call+0xc5/0x200 [<ffffffff8101d14e>] arch_cpu_idle+0xe/0x30 [<ffffffff810c67c1>] cpu_startup_entry+0xf1/0x290 [<ffffffff8104228a>] start_secondary+0x1ba/0x230 Code: 42 0f 00 45 89 e6 48 01 c2 43 8d 44 6d 00 39 d0 73 26 49 c1 e5 08 89 d2 4d 63 f4 49 63 c5 48 c1 e2 08 48 c1 e0 08 48 63 ca 48 99 <48> f7 f9 48 98 4c 0f af f0 49 c1 ee 08 8b 43 78 c1 e0 08 44 29 RIP [<ffffffff814a9279>] intel_pstate_timer_func+0x179/0x3d0 RSP <ffff883fff4e3db8> The kernel values for cpudata for CPU 113 were: struct cpudata { cpu = 113, timer = { entry = { next = 0x0, prev = 0xdead000000200200 }, expires = 8357799745, base = 0xffff883fe84ec001, function = 0xffffffff814a9100 <intel_pstate_timer_func>, data = 18446612406765768960, <snip> i_gain = 0, d_gain = 0, deadband = 0, last_err = 22489 }, last_sample_time = { tv64 = 4063132438017305 }, prev_aperf = 287326796397463, prev_mperf = 251427432090198, sample = { core_pct_busy = 23081, aperf = 2937407, mperf = 3257884, freq = 2524484, time = { tv64 = 4063149215234118 } } } which results in the time between samples = last_sample_time - sample.time = 4063149215234118 - 4063132438017305 = 16777216813 which is 16.777 seconds. The duration between reads of the APERF and MPERF registers overflowed a s32 sized integer in intel_pstate_get_scaled_busy()'s call to div_fp(). The result is that int_tofp(duration_us) == 0, and the kernel attempts to divide by 0. While the kernel shouldn't be delaying for a long time, it can and does happen and the intel_pstate driver should not panic in this situation. This patch changes the div_fp() function to use div64_s64() to allow for "long" division. This will avoid the overflow condition on long delays. [v2]: use div64_s64() in div_fp() Signed-off-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-06-15 20:43:29 +03:00
static inline int32_t div_fp(s64 x, s64 y)
{
intel_pstate: Fix overflow in busy_scaled due to long delay The kernel may delay interrupts for a long time which can result in timers being delayed. If this occurs the intel_pstate driver will crash with a divide by zero error: divide error: 0000 [#1] SMP Modules linked in: btrfs zlib_deflate raid6_pq xor msdos ext4 mbcache jbd2 binfmt_misc arc4 md4 nls_utf8 cifs dns_resolver tcp_lp bnep bluetooth rfkill fuse dm_service_time iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi nf_conntrack_netbios_ns nf_conntrack_broadcast nf_conntrack_ftp ip6t_rpfilter ip6t_REJECT ipt_REJECT xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw iptable_filter ip_tables intel_powerclamp coretemp vfat fat kvm_intel iTCO_wdt iTCO_vendor_support ipmi_devintf sr_mod kvm crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel cdc_ether lrw usbnet cdrom mii gf128mul glue_helper ablk_helper cryptd lpc_ich mfd_core pcspkr sb_edac edac_core ipmi_si ipmi_msghandler ioatdma wmi shpchp acpi_pad nfsd auth_rpcgss nfs_acl lockd uinput dm_multipath sunrpc xfs libcrc32c usb_storage sd_mod crc_t10dif crct10dif_common ixgbe mgag200 syscopyarea sysfillrect sysimgblt mdio drm_kms_helper ttm igb drm ptp pps_core dca i2c_algo_bit megaraid_sas i2c_core dm_mirror dm_region_hash dm_log dm_mod CPU: 113 PID: 0 Comm: swapper/113 Tainted: G W -------------- 3.10.0-229.1.2.el7.x86_64 #1 Hardware name: IBM x3950 X6 -[3837AC2]-/00FN827, BIOS -[A8E112BUS-1.00]- 08/27/2014 task: ffff880fe8abe660 ti: ffff880fe8ae4000 task.ti: ffff880fe8ae4000 RIP: 0010:[<ffffffff814a9279>] [<ffffffff814a9279>] intel_pstate_timer_func+0x179/0x3d0 RSP: 0018:ffff883fff4e3db8 EFLAGS: 00010206 RAX: 0000000027100000 RBX: ffff883fe6965100 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000010 RDI: 000000002e53632d RBP: ffff883fff4e3e20 R08: 000e6f69a5a125c0 R09: ffff883fe84ec001 R10: 0000000000000002 R11: 0000000000000005 R12: 00000000000049f5 R13: 0000000000271000 R14: 00000000000049f5 R15: 0000000000000246 FS: 0000000000000000(0000) GS:ffff883fff4e0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7668601000 CR3: 000000000190a000 CR4: 00000000001407e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Stack: ffff883fff4e3e58 ffffffff81099dc1 0000000000000086 0000000000000071 ffff883fff4f3680 0000000000000071 fbdc8a965e33afee ffffffff810b69dd ffff883fe84ec000 ffff883fe6965108 0000000000000100 ffffffff814a9100 Call Trace: <IRQ> [<ffffffff81099dc1>] ? run_posix_cpu_timers+0x51/0x840 [<ffffffff810b69dd>] ? trigger_load_balance+0x5d/0x200 [<ffffffff814a9100>] ? pid_param_set+0x130/0x130 [<ffffffff8107df56>] call_timer_fn+0x36/0x110 [<ffffffff814a9100>] ? pid_param_set+0x130/0x130 [<ffffffff8107fdcf>] run_timer_softirq+0x21f/0x320 [<ffffffff81077b2f>] __do_softirq+0xef/0x280 [<ffffffff816156dc>] call_softirq+0x1c/0x30 [<ffffffff81015d95>] do_softirq+0x65/0xa0 [<ffffffff81077ec5>] irq_exit+0x115/0x120 [<ffffffff81616355>] smp_apic_timer_interrupt+0x45/0x60 [<ffffffff81614a1d>] apic_timer_interrupt+0x6d/0x80 <EOI> [<ffffffff814a9c32>] ? cpuidle_enter_state+0x52/0xc0 [<ffffffff814a9c28>] ? cpuidle_enter_state+0x48/0xc0 [<ffffffff814a9d65>] cpuidle_idle_call+0xc5/0x200 [<ffffffff8101d14e>] arch_cpu_idle+0xe/0x30 [<ffffffff810c67c1>] cpu_startup_entry+0xf1/0x290 [<ffffffff8104228a>] start_secondary+0x1ba/0x230 Code: 42 0f 00 45 89 e6 48 01 c2 43 8d 44 6d 00 39 d0 73 26 49 c1 e5 08 89 d2 4d 63 f4 49 63 c5 48 c1 e2 08 48 c1 e0 08 48 63 ca 48 99 <48> f7 f9 48 98 4c 0f af f0 49 c1 ee 08 8b 43 78 c1 e0 08 44 29 RIP [<ffffffff814a9279>] intel_pstate_timer_func+0x179/0x3d0 RSP <ffff883fff4e3db8> The kernel values for cpudata for CPU 113 were: struct cpudata { cpu = 113, timer = { entry = { next = 0x0, prev = 0xdead000000200200 }, expires = 8357799745, base = 0xffff883fe84ec001, function = 0xffffffff814a9100 <intel_pstate_timer_func>, data = 18446612406765768960, <snip> i_gain = 0, d_gain = 0, deadband = 0, last_err = 22489 }, last_sample_time = { tv64 = 4063132438017305 }, prev_aperf = 287326796397463, prev_mperf = 251427432090198, sample = { core_pct_busy = 23081, aperf = 2937407, mperf = 3257884, freq = 2524484, time = { tv64 = 4063149215234118 } } } which results in the time between samples = last_sample_time - sample.time = 4063149215234118 - 4063132438017305 = 16777216813 which is 16.777 seconds. The duration between reads of the APERF and MPERF registers overflowed a s32 sized integer in intel_pstate_get_scaled_busy()'s call to div_fp(). The result is that int_tofp(duration_us) == 0, and the kernel attempts to divide by 0. While the kernel shouldn't be delaying for a long time, it can and does happen and the intel_pstate driver should not panic in this situation. This patch changes the div_fp() function to use div64_s64() to allow for "long" division. This will avoid the overflow condition on long delays. [v2]: use div64_s64() in div_fp() Signed-off-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-06-15 20:43:29 +03:00
return div64_s64((int64_t)x << FRAC_BITS, y);
}
static inline int ceiling_fp(int32_t x)
{
int mask, ret;
ret = fp_toint(x);
mask = (1 << FRAC_BITS) - 1;
if (x & mask)
ret += 1;
return ret;
}
struct sample {
int32_t core_pct_busy;
u64 aperf;
u64 mperf;
u64 tsc;
int freq;
ktime_t time;
};
struct pstate_data {
int current_pstate;
int min_pstate;
int max_pstate;
int max_pstate_physical;
int scaling;
int turbo_pstate;
};
struct vid_data {
int min;
int max;
int turbo;
int32_t ratio;
};
struct _pid {
int setpoint;
int32_t integral;
int32_t p_gain;
int32_t i_gain;
int32_t d_gain;
int deadband;
int32_t last_err;
};
struct cpudata {
int cpu;
struct timer_list timer;
struct pstate_data pstate;
struct vid_data vid;
struct _pid pid;
ktime_t last_sample_time;
u64 prev_aperf;
u64 prev_mperf;
u64 prev_tsc;
struct sample sample;
#if IS_ENABLED(CONFIG_ACPI)
struct acpi_processor_performance acpi_perf_data;
#endif
};
static struct cpudata **all_cpu_data;
struct pstate_adjust_policy {
int sample_rate_ms;
int deadband;
int setpoint;
int p_gain_pct;
int d_gain_pct;
int i_gain_pct;
};
struct pstate_funcs {
int (*get_max)(void);
int (*get_max_physical)(void);
int (*get_min)(void);
int (*get_turbo)(void);
int (*get_scaling)(void);
void (*set)(struct cpudata*, int pstate);
void (*get_vid)(struct cpudata *);
};
struct cpu_defaults {
struct pstate_adjust_policy pid_policy;
struct pstate_funcs funcs;
};
static struct pstate_adjust_policy pid_params;
static struct pstate_funcs pstate_funcs;
static int hwp_active;
static int no_acpi_perf;
struct perf_limits {
int no_turbo;
int turbo_disabled;
int max_perf_pct;
int min_perf_pct;
int32_t max_perf;
int32_t min_perf;
int max_policy_pct;
int max_sysfs_pct;
int min_policy_pct;
int min_sysfs_pct;
int max_perf_ctl;
int min_perf_ctl;
};
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
static struct perf_limits performance_limits = {
.no_turbo = 0,
.turbo_disabled = 0,
.max_perf_pct = 100,
.max_perf = int_tofp(1),
.min_perf_pct = 100,
.min_perf = int_tofp(1),
.max_policy_pct = 100,
.max_sysfs_pct = 100,
.min_policy_pct = 0,
.min_sysfs_pct = 0,
};
static struct perf_limits powersave_limits = {
.no_turbo = 0,
.turbo_disabled = 0,
.max_perf_pct = 100,
.max_perf = int_tofp(1),
.min_perf_pct = 0,
.min_perf = 0,
.max_policy_pct = 100,
.max_sysfs_pct = 100,
.min_policy_pct = 0,
.min_sysfs_pct = 0,
.max_perf_ctl = 0,
.min_perf_ctl = 0,
};
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
#ifdef CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE
static struct perf_limits *limits = &performance_limits;
#else
static struct perf_limits *limits = &powersave_limits;
#endif
#if IS_ENABLED(CONFIG_ACPI)
/*
* The max target pstate ratio is a 8 bit value in both PLATFORM_INFO MSR and
* in TURBO_RATIO_LIMIT MSR, which pstate driver stores in max_pstate and
* max_turbo_pstate fields. The PERF_CTL MSR contains 16 bit value for P state
* ratio, out of it only high 8 bits are used. For example 0x1700 is setting
* target ratio 0x17. The _PSS control value stores in a format which can be
* directly written to PERF_CTL MSR. But in intel_pstate driver this shift
* occurs during write to PERF_CTL (E.g. for cores core_set_pstate()).
* This function converts the _PSS control value to intel pstate driver format
* for comparison and assignment.
*/
static int convert_to_native_pstate_format(struct cpudata *cpu, int index)
{
return cpu->acpi_perf_data.states[index].control >> 8;
}
static int intel_pstate_init_perf_limits(struct cpufreq_policy *policy)
{
struct cpudata *cpu;
int ret;
bool turbo_absent = false;
int max_pstate_index;
int min_pss_ctl, max_pss_ctl, turbo_pss_ctl;
int i;
cpu = all_cpu_data[policy->cpu];
pr_debug("intel_pstate: default limits 0x%x 0x%x 0x%x\n",
cpu->pstate.min_pstate, cpu->pstate.max_pstate,
cpu->pstate.turbo_pstate);
if (!cpu->acpi_perf_data.shared_cpu_map &&
zalloc_cpumask_var_node(&cpu->acpi_perf_data.shared_cpu_map,
GFP_KERNEL, cpu_to_node(policy->cpu))) {
return -ENOMEM;
}
ret = acpi_processor_register_performance(&cpu->acpi_perf_data,
policy->cpu);
if (ret)
return ret;
/*
* Check if the control value in _PSS is for PERF_CTL MSR, which should
* guarantee that the states returned by it map to the states in our
* list directly.
*/
if (cpu->acpi_perf_data.control_register.space_id !=
ACPI_ADR_SPACE_FIXED_HARDWARE)
return -EIO;
pr_debug("intel_pstate: CPU%u - ACPI _PSS perf data\n", policy->cpu);
for (i = 0; i < cpu->acpi_perf_data.state_count; i++)
pr_debug(" %cP%d: %u MHz, %u mW, 0x%x\n",
(i == cpu->acpi_perf_data.state ? '*' : ' '), i,
(u32) cpu->acpi_perf_data.states[i].core_frequency,
(u32) cpu->acpi_perf_data.states[i].power,
(u32) cpu->acpi_perf_data.states[i].control);
/*
* If there is only one entry _PSS, simply ignore _PSS and continue as
* usual without taking _PSS into account
*/
if (cpu->acpi_perf_data.state_count < 2)
return 0;
turbo_pss_ctl = convert_to_native_pstate_format(cpu, 0);
min_pss_ctl = convert_to_native_pstate_format(cpu,
cpu->acpi_perf_data.state_count - 1);
/* Check if there is a turbo freq in _PSS */
if (turbo_pss_ctl <= cpu->pstate.max_pstate &&
turbo_pss_ctl > cpu->pstate.min_pstate) {
pr_debug("intel_pstate: no turbo range exists in _PSS\n");
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
limits->no_turbo = limits->turbo_disabled = 1;
cpu->pstate.turbo_pstate = cpu->pstate.max_pstate;
turbo_absent = true;
}
/* Check if the max non turbo p state < Intel P state max */
max_pstate_index = turbo_absent ? 0 : 1;
max_pss_ctl = convert_to_native_pstate_format(cpu, max_pstate_index);
if (max_pss_ctl < cpu->pstate.max_pstate &&
max_pss_ctl > cpu->pstate.min_pstate)
cpu->pstate.max_pstate = max_pss_ctl;
/* check If min perf > Intel P State min */
if (min_pss_ctl > cpu->pstate.min_pstate &&
min_pss_ctl < cpu->pstate.max_pstate) {
cpu->pstate.min_pstate = min_pss_ctl;
policy->cpuinfo.min_freq = min_pss_ctl * cpu->pstate.scaling;
}
if (turbo_absent)
policy->cpuinfo.max_freq = cpu->pstate.max_pstate *
cpu->pstate.scaling;
else {
policy->cpuinfo.max_freq = cpu->pstate.turbo_pstate *
cpu->pstate.scaling;
/*
* The _PSS table doesn't contain whole turbo frequency range.
* This just contains +1 MHZ above the max non turbo frequency,
* with control value corresponding to max turbo ratio. But
* when cpufreq set policy is called, it will call with this
* max frequency, which will cause a reduced performance as
* this driver uses real max turbo frequency as the max
* frequeny. So correct this frequency in _PSS table to
* correct max turbo frequency based on the turbo ratio.
* Also need to convert to MHz as _PSS freq is in MHz.
*/
cpu->acpi_perf_data.states[0].core_frequency =
turbo_pss_ctl * 100;
}
pr_debug("intel_pstate: Updated limits using _PSS 0x%x 0x%x 0x%x\n",
cpu->pstate.min_pstate, cpu->pstate.max_pstate,
cpu->pstate.turbo_pstate);
pr_debug("intel_pstate: policy max_freq=%d Khz min_freq = %d KHz\n",
policy->cpuinfo.max_freq, policy->cpuinfo.min_freq);
return 0;
}
static int intel_pstate_exit_perf_limits(struct cpufreq_policy *policy)
{
struct cpudata *cpu;
if (!no_acpi_perf)
return 0;
cpu = all_cpu_data[policy->cpu];
acpi_processor_unregister_performance(policy->cpu);
return 0;
}
#else
static int intel_pstate_init_perf_limits(struct cpufreq_policy *policy)
{
return 0;
}
static int intel_pstate_exit_perf_limits(struct cpufreq_policy *policy)
{
return 0;
}
#endif
static inline void pid_reset(struct _pid *pid, int setpoint, int busy,
int deadband, int integral) {
pid->setpoint = setpoint;
pid->deadband = deadband;
pid->integral = int_tofp(integral);
pid->last_err = int_tofp(setpoint) - int_tofp(busy);
}
static inline void pid_p_gain_set(struct _pid *pid, int percent)
{
pid->p_gain = div_fp(int_tofp(percent), int_tofp(100));
}
static inline void pid_i_gain_set(struct _pid *pid, int percent)
{
pid->i_gain = div_fp(int_tofp(percent), int_tofp(100));
}
static inline void pid_d_gain_set(struct _pid *pid, int percent)
{
pid->d_gain = div_fp(int_tofp(percent), int_tofp(100));
}
static signed int pid_calc(struct _pid *pid, int32_t busy)
{
signed int result;
int32_t pterm, dterm, fp_error;
int32_t integral_limit;
fp_error = int_tofp(pid->setpoint) - busy;
if (abs(fp_error) <= int_tofp(pid->deadband))
return 0;
pterm = mul_fp(pid->p_gain, fp_error);
pid->integral += fp_error;
/*
* We limit the integral here so that it will never
* get higher than 30. This prevents it from becoming
* too large an input over long periods of time and allows
* it to get factored out sooner.
*
* The value of 30 was chosen through experimentation.
*/
integral_limit = int_tofp(30);
if (pid->integral > integral_limit)
pid->integral = integral_limit;
if (pid->integral < -integral_limit)
pid->integral = -integral_limit;
dterm = mul_fp(pid->d_gain, fp_error - pid->last_err);
pid->last_err = fp_error;
result = pterm + mul_fp(pid->integral, pid->i_gain) + dterm;
result = result + (1 << (FRAC_BITS-1));
return (signed int)fp_toint(result);
}
static inline void intel_pstate_busy_pid_reset(struct cpudata *cpu)
{
pid_p_gain_set(&cpu->pid, pid_params.p_gain_pct);
pid_d_gain_set(&cpu->pid, pid_params.d_gain_pct);
pid_i_gain_set(&cpu->pid, pid_params.i_gain_pct);
pid_reset(&cpu->pid, pid_params.setpoint, 100, pid_params.deadband, 0);
}
static inline void intel_pstate_reset_all_pid(void)
{
unsigned int cpu;
for_each_online_cpu(cpu) {
if (all_cpu_data[cpu])
intel_pstate_busy_pid_reset(all_cpu_data[cpu]);
}
}
static inline void update_turbo_state(void)
{
u64 misc_en;
struct cpudata *cpu;
cpu = all_cpu_data[0];
rdmsrl(MSR_IA32_MISC_ENABLE, misc_en);
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
limits->turbo_disabled =
(misc_en & MSR_IA32_MISC_ENABLE_TURBO_DISABLE ||
cpu->pstate.max_pstate == cpu->pstate.turbo_pstate);
}
static void intel_pstate_hwp_set(void)
{
int min, hw_min, max, hw_max, cpu, range, adj_range;
u64 value, cap;
rdmsrl(MSR_HWP_CAPABILITIES, cap);
hw_min = HWP_LOWEST_PERF(cap);
hw_max = HWP_HIGHEST_PERF(cap);
range = hw_max - hw_min;
get_online_cpus();
for_each_online_cpu(cpu) {
rdmsrl_on_cpu(cpu, MSR_HWP_REQUEST, &value);
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
adj_range = limits->min_perf_pct * range / 100;
min = hw_min + adj_range;
value &= ~HWP_MIN_PERF(~0L);
value |= HWP_MIN_PERF(min);
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
adj_range = limits->max_perf_pct * range / 100;
max = hw_min + adj_range;
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
if (limits->no_turbo) {
hw_max = HWP_GUARANTEED_PERF(cap);
if (hw_max < max)
max = hw_max;
}
value &= ~HWP_MAX_PERF(~0L);
value |= HWP_MAX_PERF(max);
wrmsrl_on_cpu(cpu, MSR_HWP_REQUEST, value);
}
put_online_cpus();
}
/************************** debugfs begin ************************/
static int pid_param_set(void *data, u64 val)
{
*(u32 *)data = val;
intel_pstate_reset_all_pid();
return 0;
}
static int pid_param_get(void *data, u64 *val)
{
*val = *(u32 *)data;
return 0;
}
DEFINE_SIMPLE_ATTRIBUTE(fops_pid_param, pid_param_get, pid_param_set, "%llu\n");
struct pid_param {
char *name;
void *value;
};
static struct pid_param pid_files[] = {
{"sample_rate_ms", &pid_params.sample_rate_ms},
{"d_gain_pct", &pid_params.d_gain_pct},
{"i_gain_pct", &pid_params.i_gain_pct},
{"deadband", &pid_params.deadband},
{"setpoint", &pid_params.setpoint},
{"p_gain_pct", &pid_params.p_gain_pct},
{NULL, NULL}
};
static void __init intel_pstate_debug_expose_params(void)
{
struct dentry *debugfs_parent;
int i = 0;
if (hwp_active)
return;
debugfs_parent = debugfs_create_dir("pstate_snb", NULL);
if (IS_ERR_OR_NULL(debugfs_parent))
return;
while (pid_files[i].name) {
debugfs_create_file(pid_files[i].name, 0660,
debugfs_parent, pid_files[i].value,
&fops_pid_param);
i++;
}
}
/************************** debugfs end ************************/
/************************** sysfs begin ************************/
#define show_one(file_name, object) \
static ssize_t show_##file_name \
(struct kobject *kobj, struct attribute *attr, char *buf) \
{ \
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
return sprintf(buf, "%u\n", limits->object); \
}
static ssize_t show_turbo_pct(struct kobject *kobj,
struct attribute *attr, char *buf)
{
struct cpudata *cpu;
int total, no_turbo, turbo_pct;
uint32_t turbo_fp;
cpu = all_cpu_data[0];
total = cpu->pstate.turbo_pstate - cpu->pstate.min_pstate + 1;
no_turbo = cpu->pstate.max_pstate - cpu->pstate.min_pstate + 1;
turbo_fp = div_fp(int_tofp(no_turbo), int_tofp(total));
turbo_pct = 100 - fp_toint(mul_fp(turbo_fp, int_tofp(100)));
return sprintf(buf, "%u\n", turbo_pct);
}
static ssize_t show_num_pstates(struct kobject *kobj,
struct attribute *attr, char *buf)
{
struct cpudata *cpu;
int total;
cpu = all_cpu_data[0];
total = cpu->pstate.turbo_pstate - cpu->pstate.min_pstate + 1;
return sprintf(buf, "%u\n", total);
}
static ssize_t show_no_turbo(struct kobject *kobj,
struct attribute *attr, char *buf)
{
ssize_t ret;
update_turbo_state();
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
if (limits->turbo_disabled)
ret = sprintf(buf, "%u\n", limits->turbo_disabled);
else
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
ret = sprintf(buf, "%u\n", limits->no_turbo);
return ret;
}
static ssize_t store_no_turbo(struct kobject *a, struct attribute *b,
const char *buf, size_t count)
{
unsigned int input;
int ret;
ret = sscanf(buf, "%u", &input);
if (ret != 1)
return -EINVAL;
update_turbo_state();
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
if (limits->turbo_disabled) {
pr_warn("intel_pstate: Turbo disabled by BIOS or unavailable on processor\n");
return -EPERM;
}
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
limits->no_turbo = clamp_t(int, input, 0, 1);
if (hwp_active)
intel_pstate_hwp_set();
return count;
}
static ssize_t store_max_perf_pct(struct kobject *a, struct attribute *b,
const char *buf, size_t count)
{
unsigned int input;
int ret;
ret = sscanf(buf, "%u", &input);
if (ret != 1)
return -EINVAL;
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
limits->max_sysfs_pct = clamp_t(int, input, 0 , 100);
limits->max_perf_pct = min(limits->max_policy_pct,
limits->max_sysfs_pct);
limits->max_perf_pct = max(limits->min_policy_pct,
limits->max_perf_pct);
limits->max_perf_pct = max(limits->min_perf_pct,
limits->max_perf_pct);
limits->max_perf = div_fp(int_tofp(limits->max_perf_pct),
int_tofp(100));
if (hwp_active)
intel_pstate_hwp_set();
return count;
}
static ssize_t store_min_perf_pct(struct kobject *a, struct attribute *b,
const char *buf, size_t count)
{
unsigned int input;
int ret;
ret = sscanf(buf, "%u", &input);
if (ret != 1)
return -EINVAL;
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
limits->min_sysfs_pct = clamp_t(int, input, 0 , 100);
limits->min_perf_pct = max(limits->min_policy_pct,
limits->min_sysfs_pct);
limits->min_perf_pct = min(limits->max_policy_pct,
limits->min_perf_pct);
limits->min_perf_pct = min(limits->max_perf_pct,
limits->min_perf_pct);
limits->min_perf = div_fp(int_tofp(limits->min_perf_pct),
int_tofp(100));
if (hwp_active)
intel_pstate_hwp_set();
return count;
}
show_one(max_perf_pct, max_perf_pct);
show_one(min_perf_pct, min_perf_pct);
define_one_global_rw(no_turbo);
define_one_global_rw(max_perf_pct);
define_one_global_rw(min_perf_pct);
define_one_global_ro(turbo_pct);
define_one_global_ro(num_pstates);
static struct attribute *intel_pstate_attributes[] = {
&no_turbo.attr,
&max_perf_pct.attr,
&min_perf_pct.attr,
&turbo_pct.attr,
&num_pstates.attr,
NULL
};
static struct attribute_group intel_pstate_attr_group = {
.attrs = intel_pstate_attributes,
};
static void __init intel_pstate_sysfs_expose_params(void)
{
struct kobject *intel_pstate_kobject;
int rc;
intel_pstate_kobject = kobject_create_and_add("intel_pstate",
&cpu_subsys.dev_root->kobj);
BUG_ON(!intel_pstate_kobject);
rc = sysfs_create_group(intel_pstate_kobject, &intel_pstate_attr_group);
BUG_ON(rc);
}
/************************** sysfs end ************************/
static void intel_pstate_hwp_enable(struct cpudata *cpudata)
{
pr_info("intel_pstate: HWP enabled\n");
wrmsrl_on_cpu(cpudata->cpu, MSR_PM_ENABLE, 0x1);
}
static int byt_get_min_pstate(void)
{
u64 value;
rdmsrl(BYT_RATIOS, value);
return (value >> 8) & 0x7F;
}
static int byt_get_max_pstate(void)
{
u64 value;
rdmsrl(BYT_RATIOS, value);
return (value >> 16) & 0x7F;
}
static int byt_get_turbo_pstate(void)
{
u64 value;
rdmsrl(BYT_TURBO_RATIOS, value);
return value & 0x7F;
}
static void byt_set_pstate(struct cpudata *cpudata, int pstate)
{
u64 val;
int32_t vid_fp;
u32 vid;
val = (u64)pstate << 8;
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
if (limits->no_turbo && !limits->turbo_disabled)
val |= (u64)1 << 32;
vid_fp = cpudata->vid.min + mul_fp(
int_tofp(pstate - cpudata->pstate.min_pstate),
cpudata->vid.ratio);
vid_fp = clamp_t(int32_t, vid_fp, cpudata->vid.min, cpudata->vid.max);
vid = ceiling_fp(vid_fp);
if (pstate > cpudata->pstate.max_pstate)
vid = cpudata->vid.turbo;
val |= vid;
wrmsrl_on_cpu(cpudata->cpu, MSR_IA32_PERF_CTL, val);
}
#define BYT_BCLK_FREQS 5
static int byt_freq_table[BYT_BCLK_FREQS] = { 833, 1000, 1333, 1167, 800};
static int byt_get_scaling(void)
{
u64 value;
int i;
rdmsrl(MSR_FSB_FREQ, value);
i = value & 0x3;
BUG_ON(i > BYT_BCLK_FREQS);
return byt_freq_table[i] * 100;
}
static void byt_get_vid(struct cpudata *cpudata)
{
u64 value;
rdmsrl(BYT_VIDS, value);
cpudata->vid.min = int_tofp((value >> 8) & 0x7f);
cpudata->vid.max = int_tofp((value >> 16) & 0x7f);
cpudata->vid.ratio = div_fp(
cpudata->vid.max - cpudata->vid.min,
int_tofp(cpudata->pstate.max_pstate -
cpudata->pstate.min_pstate));
rdmsrl(BYT_TURBO_VIDS, value);
cpudata->vid.turbo = value & 0x7f;
}
static int core_get_min_pstate(void)
{
u64 value;
rdmsrl(MSR_PLATFORM_INFO, value);
return (value >> 40) & 0xFF;
}
static int core_get_max_pstate_physical(void)
{
u64 value;
rdmsrl(MSR_PLATFORM_INFO, value);
return (value >> 8) & 0xFF;
}
static int core_get_max_pstate(void)
{
u64 tar;
u64 plat_info;
int max_pstate;
int err;
rdmsrl(MSR_PLATFORM_INFO, plat_info);
max_pstate = (plat_info >> 8) & 0xFF;
err = rdmsrl_safe(MSR_TURBO_ACTIVATION_RATIO, &tar);
if (!err) {
/* Do some sanity checking for safety */
if (plat_info & 0x600000000) {
u64 tdp_ctrl;
u64 tdp_ratio;
int tdp_msr;
err = rdmsrl_safe(MSR_CONFIG_TDP_CONTROL, &tdp_ctrl);
if (err)
goto skip_tar;
tdp_msr = MSR_CONFIG_TDP_NOMINAL + tdp_ctrl;
err = rdmsrl_safe(tdp_msr, &tdp_ratio);
if (err)
goto skip_tar;
if (tdp_ratio - 1 == tar) {
max_pstate = tar;
pr_debug("max_pstate=TAC %x\n", max_pstate);
} else {
goto skip_tar;
}
}
}
skip_tar:
return max_pstate;
}
static int core_get_turbo_pstate(void)
{
u64 value;
int nont, ret;
rdmsrl(MSR_NHM_TURBO_RATIO_LIMIT, value);
nont = core_get_max_pstate();
ret = (value) & 255;
if (ret <= nont)
ret = nont;
return ret;
}
static inline int core_get_scaling(void)
{
return 100000;
}
static void core_set_pstate(struct cpudata *cpudata, int pstate)
{
u64 val;
val = (u64)pstate << 8;
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
if (limits->no_turbo && !limits->turbo_disabled)
val |= (u64)1 << 32;
wrmsrl_on_cpu(cpudata->cpu, MSR_IA32_PERF_CTL, val);
}
static int knl_get_turbo_pstate(void)
{
u64 value;
int nont, ret;
rdmsrl(MSR_NHM_TURBO_RATIO_LIMIT, value);
nont = core_get_max_pstate();
ret = (((value) >> 8) & 0xFF);
if (ret <= nont)
ret = nont;
return ret;
}
static struct cpu_defaults core_params = {
.pid_policy = {
.sample_rate_ms = 10,
.deadband = 0,
.setpoint = 97,
.p_gain_pct = 20,
.d_gain_pct = 0,
.i_gain_pct = 0,
},
.funcs = {
.get_max = core_get_max_pstate,
.get_max_physical = core_get_max_pstate_physical,
.get_min = core_get_min_pstate,
.get_turbo = core_get_turbo_pstate,
.get_scaling = core_get_scaling,
.set = core_set_pstate,
},
};
static struct cpu_defaults byt_params = {
.pid_policy = {
.sample_rate_ms = 10,
.deadband = 0,
.setpoint = 60,
.p_gain_pct = 14,
.d_gain_pct = 0,
.i_gain_pct = 4,
},
.funcs = {
.get_max = byt_get_max_pstate,
.get_max_physical = byt_get_max_pstate,
.get_min = byt_get_min_pstate,
.get_turbo = byt_get_turbo_pstate,
.set = byt_set_pstate,
.get_scaling = byt_get_scaling,
.get_vid = byt_get_vid,
},
};
static struct cpu_defaults knl_params = {
.pid_policy = {
.sample_rate_ms = 10,
.deadband = 0,
.setpoint = 97,
.p_gain_pct = 20,
.d_gain_pct = 0,
.i_gain_pct = 0,
},
.funcs = {
.get_max = core_get_max_pstate,
.get_max_physical = core_get_max_pstate_physical,
.get_min = core_get_min_pstate,
.get_turbo = knl_get_turbo_pstate,
.get_scaling = core_get_scaling,
.set = core_set_pstate,
},
};
static void intel_pstate_get_min_max(struct cpudata *cpu, int *min, int *max)
{
int max_perf = cpu->pstate.turbo_pstate;
int max_perf_adj;
int min_perf;
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
if (limits->no_turbo || limits->turbo_disabled)
max_perf = cpu->pstate.max_pstate;
/*
* performance can be limited by user through sysfs, by cpufreq
* policy, or by cpu specific default values determined through
* experimentation.
*/
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
if (limits->max_perf_ctl && limits->max_sysfs_pct >=
limits->max_policy_pct) {
*max = limits->max_perf_ctl;
} else {
max_perf_adj = fp_toint(mul_fp(int_tofp(max_perf),
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
limits->max_perf));
*max = clamp_t(int, max_perf_adj, cpu->pstate.min_pstate,
cpu->pstate.turbo_pstate);
}
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
if (limits->min_perf_ctl) {
*min = limits->min_perf_ctl;
} else {
min_perf = fp_toint(mul_fp(int_tofp(max_perf),
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
limits->min_perf));
*min = clamp_t(int, min_perf, cpu->pstate.min_pstate, max_perf);
}
}
static void intel_pstate_set_pstate(struct cpudata *cpu, int pstate, bool force)
{
int max_perf, min_perf;
if (force) {
update_turbo_state();
intel_pstate_get_min_max(cpu, &min_perf, &max_perf);
pstate = clamp_t(int, pstate, min_perf, max_perf);
if (pstate == cpu->pstate.current_pstate)
return;
}
trace_cpu_frequency(pstate * cpu->pstate.scaling, cpu->cpu);
cpu->pstate.current_pstate = pstate;
pstate_funcs.set(cpu, pstate);
}
static void intel_pstate_get_cpu_pstates(struct cpudata *cpu)
{
cpu->pstate.min_pstate = pstate_funcs.get_min();
cpu->pstate.max_pstate = pstate_funcs.get_max();
cpu->pstate.max_pstate_physical = pstate_funcs.get_max_physical();
cpu->pstate.turbo_pstate = pstate_funcs.get_turbo();
cpu->pstate.scaling = pstate_funcs.get_scaling();
if (pstate_funcs.get_vid)
pstate_funcs.get_vid(cpu);
intel_pstate_set_pstate(cpu, cpu->pstate.min_pstate, false);
}
static inline void intel_pstate_calc_busy(struct cpudata *cpu)
{
struct sample *sample = &cpu->sample;
int64_t core_pct;
core_pct = int_tofp(sample->aperf) * int_tofp(100);
core_pct = div64_u64(core_pct, int_tofp(sample->mperf));
sample->freq = fp_toint(
mul_fp(int_tofp(
cpu->pstate.max_pstate_physical *
cpu->pstate.scaling / 100),
core_pct));
sample->core_pct_busy = (int32_t)core_pct;
}
static inline void intel_pstate_sample(struct cpudata *cpu)
{
u64 aperf, mperf;
unsigned long flags;
u64 tsc;
local_irq_save(flags);
rdmsrl(MSR_IA32_APERF, aperf);
rdmsrl(MSR_IA32_MPERF, mperf);
if (cpu->prev_mperf == mperf) {
local_irq_restore(flags);
return;
}
tsc = rdtsc();
local_irq_restore(flags);
cpu->last_sample_time = cpu->sample.time;
cpu->sample.time = ktime_get();
cpu->sample.aperf = aperf;
cpu->sample.mperf = mperf;
cpu->sample.tsc = tsc;
cpu->sample.aperf -= cpu->prev_aperf;
cpu->sample.mperf -= cpu->prev_mperf;
cpu->sample.tsc -= cpu->prev_tsc;
intel_pstate_calc_busy(cpu);
cpu->prev_aperf = aperf;
cpu->prev_mperf = mperf;
cpu->prev_tsc = tsc;
}
static inline void intel_hwp_set_sample_time(struct cpudata *cpu)
{
int delay;
delay = msecs_to_jiffies(50);
mod_timer_pinned(&cpu->timer, jiffies + delay);
}
static inline void intel_pstate_set_sample_time(struct cpudata *cpu)
{
int delay;
delay = msecs_to_jiffies(pid_params.sample_rate_ms);
mod_timer_pinned(&cpu->timer, jiffies + delay);
}
static inline int32_t intel_pstate_get_scaled_busy(struct cpudata *cpu)
{
int32_t core_busy, max_pstate, current_pstate, sample_ratio;
intel_pstate: Fix overflow in busy_scaled due to long delay The kernel may delay interrupts for a long time which can result in timers being delayed. If this occurs the intel_pstate driver will crash with a divide by zero error: divide error: 0000 [#1] SMP Modules linked in: btrfs zlib_deflate raid6_pq xor msdos ext4 mbcache jbd2 binfmt_misc arc4 md4 nls_utf8 cifs dns_resolver tcp_lp bnep bluetooth rfkill fuse dm_service_time iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi nf_conntrack_netbios_ns nf_conntrack_broadcast nf_conntrack_ftp ip6t_rpfilter ip6t_REJECT ipt_REJECT xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw iptable_filter ip_tables intel_powerclamp coretemp vfat fat kvm_intel iTCO_wdt iTCO_vendor_support ipmi_devintf sr_mod kvm crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel cdc_ether lrw usbnet cdrom mii gf128mul glue_helper ablk_helper cryptd lpc_ich mfd_core pcspkr sb_edac edac_core ipmi_si ipmi_msghandler ioatdma wmi shpchp acpi_pad nfsd auth_rpcgss nfs_acl lockd uinput dm_multipath sunrpc xfs libcrc32c usb_storage sd_mod crc_t10dif crct10dif_common ixgbe mgag200 syscopyarea sysfillrect sysimgblt mdio drm_kms_helper ttm igb drm ptp pps_core dca i2c_algo_bit megaraid_sas i2c_core dm_mirror dm_region_hash dm_log dm_mod CPU: 113 PID: 0 Comm: swapper/113 Tainted: G W -------------- 3.10.0-229.1.2.el7.x86_64 #1 Hardware name: IBM x3950 X6 -[3837AC2]-/00FN827, BIOS -[A8E112BUS-1.00]- 08/27/2014 task: ffff880fe8abe660 ti: ffff880fe8ae4000 task.ti: ffff880fe8ae4000 RIP: 0010:[<ffffffff814a9279>] [<ffffffff814a9279>] intel_pstate_timer_func+0x179/0x3d0 RSP: 0018:ffff883fff4e3db8 EFLAGS: 00010206 RAX: 0000000027100000 RBX: ffff883fe6965100 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000010 RDI: 000000002e53632d RBP: ffff883fff4e3e20 R08: 000e6f69a5a125c0 R09: ffff883fe84ec001 R10: 0000000000000002 R11: 0000000000000005 R12: 00000000000049f5 R13: 0000000000271000 R14: 00000000000049f5 R15: 0000000000000246 FS: 0000000000000000(0000) GS:ffff883fff4e0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7668601000 CR3: 000000000190a000 CR4: 00000000001407e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Stack: ffff883fff4e3e58 ffffffff81099dc1 0000000000000086 0000000000000071 ffff883fff4f3680 0000000000000071 fbdc8a965e33afee ffffffff810b69dd ffff883fe84ec000 ffff883fe6965108 0000000000000100 ffffffff814a9100 Call Trace: <IRQ> [<ffffffff81099dc1>] ? run_posix_cpu_timers+0x51/0x840 [<ffffffff810b69dd>] ? trigger_load_balance+0x5d/0x200 [<ffffffff814a9100>] ? pid_param_set+0x130/0x130 [<ffffffff8107df56>] call_timer_fn+0x36/0x110 [<ffffffff814a9100>] ? pid_param_set+0x130/0x130 [<ffffffff8107fdcf>] run_timer_softirq+0x21f/0x320 [<ffffffff81077b2f>] __do_softirq+0xef/0x280 [<ffffffff816156dc>] call_softirq+0x1c/0x30 [<ffffffff81015d95>] do_softirq+0x65/0xa0 [<ffffffff81077ec5>] irq_exit+0x115/0x120 [<ffffffff81616355>] smp_apic_timer_interrupt+0x45/0x60 [<ffffffff81614a1d>] apic_timer_interrupt+0x6d/0x80 <EOI> [<ffffffff814a9c32>] ? cpuidle_enter_state+0x52/0xc0 [<ffffffff814a9c28>] ? cpuidle_enter_state+0x48/0xc0 [<ffffffff814a9d65>] cpuidle_idle_call+0xc5/0x200 [<ffffffff8101d14e>] arch_cpu_idle+0xe/0x30 [<ffffffff810c67c1>] cpu_startup_entry+0xf1/0x290 [<ffffffff8104228a>] start_secondary+0x1ba/0x230 Code: 42 0f 00 45 89 e6 48 01 c2 43 8d 44 6d 00 39 d0 73 26 49 c1 e5 08 89 d2 4d 63 f4 49 63 c5 48 c1 e2 08 48 c1 e0 08 48 63 ca 48 99 <48> f7 f9 48 98 4c 0f af f0 49 c1 ee 08 8b 43 78 c1 e0 08 44 29 RIP [<ffffffff814a9279>] intel_pstate_timer_func+0x179/0x3d0 RSP <ffff883fff4e3db8> The kernel values for cpudata for CPU 113 were: struct cpudata { cpu = 113, timer = { entry = { next = 0x0, prev = 0xdead000000200200 }, expires = 8357799745, base = 0xffff883fe84ec001, function = 0xffffffff814a9100 <intel_pstate_timer_func>, data = 18446612406765768960, <snip> i_gain = 0, d_gain = 0, deadband = 0, last_err = 22489 }, last_sample_time = { tv64 = 4063132438017305 }, prev_aperf = 287326796397463, prev_mperf = 251427432090198, sample = { core_pct_busy = 23081, aperf = 2937407, mperf = 3257884, freq = 2524484, time = { tv64 = 4063149215234118 } } } which results in the time between samples = last_sample_time - sample.time = 4063149215234118 - 4063132438017305 = 16777216813 which is 16.777 seconds. The duration between reads of the APERF and MPERF registers overflowed a s32 sized integer in intel_pstate_get_scaled_busy()'s call to div_fp(). The result is that int_tofp(duration_us) == 0, and the kernel attempts to divide by 0. While the kernel shouldn't be delaying for a long time, it can and does happen and the intel_pstate driver should not panic in this situation. This patch changes the div_fp() function to use div64_s64() to allow for "long" division. This will avoid the overflow condition on long delays. [v2]: use div64_s64() in div_fp() Signed-off-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-06-15 20:43:29 +03:00
s64 duration_us;
u32 sample_time;
/*
* core_busy is the ratio of actual performance to max
* max_pstate is the max non turbo pstate available
* current_pstate was the pstate that was requested during
* the last sample period.
*
* We normalize core_busy, which was our actual percent
* performance to what we requested during the last sample
* period. The result will be a percentage of busy at a
* specified pstate.
*/
core_busy = cpu->sample.core_pct_busy;
max_pstate = int_tofp(cpu->pstate.max_pstate_physical);
current_pstate = int_tofp(cpu->pstate.current_pstate);
core_busy = mul_fp(core_busy, div_fp(max_pstate, current_pstate));
/*
* Since we have a deferred timer, it will not fire unless
* we are in C0. So, determine if the actual elapsed time
* is significantly greater (3x) than our sample interval. If it
* is, then we were idle for a long enough period of time
* to adjust our busyness.
*/
sample_time = pid_params.sample_rate_ms * USEC_PER_MSEC;
intel_pstate: Fix overflow in busy_scaled due to long delay The kernel may delay interrupts for a long time which can result in timers being delayed. If this occurs the intel_pstate driver will crash with a divide by zero error: divide error: 0000 [#1] SMP Modules linked in: btrfs zlib_deflate raid6_pq xor msdos ext4 mbcache jbd2 binfmt_misc arc4 md4 nls_utf8 cifs dns_resolver tcp_lp bnep bluetooth rfkill fuse dm_service_time iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi nf_conntrack_netbios_ns nf_conntrack_broadcast nf_conntrack_ftp ip6t_rpfilter ip6t_REJECT ipt_REJECT xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw iptable_filter ip_tables intel_powerclamp coretemp vfat fat kvm_intel iTCO_wdt iTCO_vendor_support ipmi_devintf sr_mod kvm crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel cdc_ether lrw usbnet cdrom mii gf128mul glue_helper ablk_helper cryptd lpc_ich mfd_core pcspkr sb_edac edac_core ipmi_si ipmi_msghandler ioatdma wmi shpchp acpi_pad nfsd auth_rpcgss nfs_acl lockd uinput dm_multipath sunrpc xfs libcrc32c usb_storage sd_mod crc_t10dif crct10dif_common ixgbe mgag200 syscopyarea sysfillrect sysimgblt mdio drm_kms_helper ttm igb drm ptp pps_core dca i2c_algo_bit megaraid_sas i2c_core dm_mirror dm_region_hash dm_log dm_mod CPU: 113 PID: 0 Comm: swapper/113 Tainted: G W -------------- 3.10.0-229.1.2.el7.x86_64 #1 Hardware name: IBM x3950 X6 -[3837AC2]-/00FN827, BIOS -[A8E112BUS-1.00]- 08/27/2014 task: ffff880fe8abe660 ti: ffff880fe8ae4000 task.ti: ffff880fe8ae4000 RIP: 0010:[<ffffffff814a9279>] [<ffffffff814a9279>] intel_pstate_timer_func+0x179/0x3d0 RSP: 0018:ffff883fff4e3db8 EFLAGS: 00010206 RAX: 0000000027100000 RBX: ffff883fe6965100 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000010 RDI: 000000002e53632d RBP: ffff883fff4e3e20 R08: 000e6f69a5a125c0 R09: ffff883fe84ec001 R10: 0000000000000002 R11: 0000000000000005 R12: 00000000000049f5 R13: 0000000000271000 R14: 00000000000049f5 R15: 0000000000000246 FS: 0000000000000000(0000) GS:ffff883fff4e0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7668601000 CR3: 000000000190a000 CR4: 00000000001407e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Stack: ffff883fff4e3e58 ffffffff81099dc1 0000000000000086 0000000000000071 ffff883fff4f3680 0000000000000071 fbdc8a965e33afee ffffffff810b69dd ffff883fe84ec000 ffff883fe6965108 0000000000000100 ffffffff814a9100 Call Trace: <IRQ> [<ffffffff81099dc1>] ? run_posix_cpu_timers+0x51/0x840 [<ffffffff810b69dd>] ? trigger_load_balance+0x5d/0x200 [<ffffffff814a9100>] ? pid_param_set+0x130/0x130 [<ffffffff8107df56>] call_timer_fn+0x36/0x110 [<ffffffff814a9100>] ? pid_param_set+0x130/0x130 [<ffffffff8107fdcf>] run_timer_softirq+0x21f/0x320 [<ffffffff81077b2f>] __do_softirq+0xef/0x280 [<ffffffff816156dc>] call_softirq+0x1c/0x30 [<ffffffff81015d95>] do_softirq+0x65/0xa0 [<ffffffff81077ec5>] irq_exit+0x115/0x120 [<ffffffff81616355>] smp_apic_timer_interrupt+0x45/0x60 [<ffffffff81614a1d>] apic_timer_interrupt+0x6d/0x80 <EOI> [<ffffffff814a9c32>] ? cpuidle_enter_state+0x52/0xc0 [<ffffffff814a9c28>] ? cpuidle_enter_state+0x48/0xc0 [<ffffffff814a9d65>] cpuidle_idle_call+0xc5/0x200 [<ffffffff8101d14e>] arch_cpu_idle+0xe/0x30 [<ffffffff810c67c1>] cpu_startup_entry+0xf1/0x290 [<ffffffff8104228a>] start_secondary+0x1ba/0x230 Code: 42 0f 00 45 89 e6 48 01 c2 43 8d 44 6d 00 39 d0 73 26 49 c1 e5 08 89 d2 4d 63 f4 49 63 c5 48 c1 e2 08 48 c1 e0 08 48 63 ca 48 99 <48> f7 f9 48 98 4c 0f af f0 49 c1 ee 08 8b 43 78 c1 e0 08 44 29 RIP [<ffffffff814a9279>] intel_pstate_timer_func+0x179/0x3d0 RSP <ffff883fff4e3db8> The kernel values for cpudata for CPU 113 were: struct cpudata { cpu = 113, timer = { entry = { next = 0x0, prev = 0xdead000000200200 }, expires = 8357799745, base = 0xffff883fe84ec001, function = 0xffffffff814a9100 <intel_pstate_timer_func>, data = 18446612406765768960, <snip> i_gain = 0, d_gain = 0, deadband = 0, last_err = 22489 }, last_sample_time = { tv64 = 4063132438017305 }, prev_aperf = 287326796397463, prev_mperf = 251427432090198, sample = { core_pct_busy = 23081, aperf = 2937407, mperf = 3257884, freq = 2524484, time = { tv64 = 4063149215234118 } } } which results in the time between samples = last_sample_time - sample.time = 4063149215234118 - 4063132438017305 = 16777216813 which is 16.777 seconds. The duration between reads of the APERF and MPERF registers overflowed a s32 sized integer in intel_pstate_get_scaled_busy()'s call to div_fp(). The result is that int_tofp(duration_us) == 0, and the kernel attempts to divide by 0. While the kernel shouldn't be delaying for a long time, it can and does happen and the intel_pstate driver should not panic in this situation. This patch changes the div_fp() function to use div64_s64() to allow for "long" division. This will avoid the overflow condition on long delays. [v2]: use div64_s64() in div_fp() Signed-off-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-06-15 20:43:29 +03:00
duration_us = ktime_us_delta(cpu->sample.time,
cpu->last_sample_time);
if (duration_us > sample_time * 3) {
sample_ratio = div_fp(int_tofp(sample_time),
int_tofp(duration_us));
core_busy = mul_fp(core_busy, sample_ratio);
}
return core_busy;
}
static inline void intel_pstate_adjust_busy_pstate(struct cpudata *cpu)
{
int32_t busy_scaled;
struct _pid *pid;
signed int ctl;
int from;
struct sample *sample;
from = cpu->pstate.current_pstate;
pid = &cpu->pid;
busy_scaled = intel_pstate_get_scaled_busy(cpu);
ctl = pid_calc(pid, busy_scaled);
/* Negative values of ctl increase the pstate and vice versa */
intel_pstate_set_pstate(cpu, cpu->pstate.current_pstate - ctl, true);
sample = &cpu->sample;
trace_pstate_sample(fp_toint(sample->core_pct_busy),
fp_toint(busy_scaled),
from,
cpu->pstate.current_pstate,
sample->mperf,
sample->aperf,
sample->tsc,
sample->freq);
}
static void intel_hwp_timer_func(unsigned long __data)
{
struct cpudata *cpu = (struct cpudata *) __data;
intel_pstate_sample(cpu);
intel_hwp_set_sample_time(cpu);
}
static void intel_pstate_timer_func(unsigned long __data)
{
struct cpudata *cpu = (struct cpudata *) __data;
intel_pstate_sample(cpu);
intel_pstate_adjust_busy_pstate(cpu);
intel_pstate_set_sample_time(cpu);
}
#define ICPU(model, policy) \
{ X86_VENDOR_INTEL, 6, model, X86_FEATURE_APERFMPERF,\
(unsigned long)&policy }
static const struct x86_cpu_id intel_pstate_cpu_ids[] = {
ICPU(0x2a, core_params),
ICPU(0x2d, core_params),
ICPU(0x37, byt_params),
ICPU(0x3a, core_params),
ICPU(0x3c, core_params),
ICPU(0x3d, core_params),
ICPU(0x3e, core_params),
ICPU(0x3f, core_params),
ICPU(0x45, core_params),
ICPU(0x46, core_params),
ICPU(0x47, core_params),
ICPU(0x4c, byt_params),
ICPU(0x4e, core_params),
ICPU(0x4f, core_params),
ICPU(0x5e, core_params),
ICPU(0x56, core_params),
ICPU(0x57, knl_params),
{}
};
MODULE_DEVICE_TABLE(x86cpu, intel_pstate_cpu_ids);
static const struct x86_cpu_id intel_pstate_cpu_oob_ids[] = {
ICPU(0x56, core_params),
{}
};
static int intel_pstate_init_cpu(unsigned int cpunum)
{
struct cpudata *cpu;
if (!all_cpu_data[cpunum])
all_cpu_data[cpunum] = kzalloc(sizeof(struct cpudata),
GFP_KERNEL);
if (!all_cpu_data[cpunum])
return -ENOMEM;
cpu = all_cpu_data[cpunum];
cpu->cpu = cpunum;
if (hwp_active)
intel_pstate_hwp_enable(cpu);
intel_pstate_get_cpu_pstates(cpu);
init_timer_deferrable(&cpu->timer);
cpu->timer.data = (unsigned long)cpu;
cpu->timer.expires = jiffies + HZ/100;
if (!hwp_active)
cpu->timer.function = intel_pstate_timer_func;
else
cpu->timer.function = intel_hwp_timer_func;
intel_pstate_busy_pid_reset(cpu);
intel_pstate_sample(cpu);
add_timer_on(&cpu->timer, cpunum);
pr_debug("intel_pstate: controlling: cpu %d\n", cpunum);
return 0;
}
static unsigned int intel_pstate_get(unsigned int cpu_num)
{
struct sample *sample;
struct cpudata *cpu;
cpu = all_cpu_data[cpu_num];
if (!cpu)
return 0;
sample = &cpu->sample;
return sample->freq;
}
static int intel_pstate_set_policy(struct cpufreq_policy *policy)
{
#if IS_ENABLED(CONFIG_ACPI)
struct cpudata *cpu;
int i;
#endif
pr_debug("intel_pstate: %s max %u policy->max %u\n", __func__,
policy->cpuinfo.max_freq, policy->max);
if (!policy->cpuinfo.max_freq)
return -ENODEV;
if (policy->policy == CPUFREQ_POLICY_PERFORMANCE &&
policy->max >= policy->cpuinfo.max_freq) {
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
pr_debug("intel_pstate: set performance\n");
limits = &performance_limits;
return 0;
}
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
pr_debug("intel_pstate: set powersave\n");
limits = &powersave_limits;
limits->min_policy_pct = (policy->min * 100) / policy->cpuinfo.max_freq;
limits->min_policy_pct = clamp_t(int, limits->min_policy_pct, 0 , 100);
limits->max_policy_pct = (policy->max * 100) / policy->cpuinfo.max_freq;
limits->max_policy_pct = clamp_t(int, limits->max_policy_pct, 0 , 100);
/* Normalize user input to [min_policy_pct, max_policy_pct] */
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
limits->min_perf_pct = max(limits->min_policy_pct,
limits->min_sysfs_pct);
limits->min_perf_pct = min(limits->max_policy_pct,
limits->min_perf_pct);
limits->max_perf_pct = min(limits->max_policy_pct,
limits->max_sysfs_pct);
limits->max_perf_pct = max(limits->min_policy_pct,
limits->max_perf_pct);
/* Make sure min_perf_pct <= max_perf_pct */
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
limits->min_perf_pct = min(limits->max_perf_pct, limits->min_perf_pct);
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
limits->min_perf = div_fp(int_tofp(limits->min_perf_pct),
int_tofp(100));
limits->max_perf = div_fp(int_tofp(limits->max_perf_pct),
int_tofp(100));
#if IS_ENABLED(CONFIG_ACPI)
cpu = all_cpu_data[policy->cpu];
for (i = 0; i < cpu->acpi_perf_data.state_count; i++) {
int control;
control = convert_to_native_pstate_format(cpu, i);
if (control * cpu->pstate.scaling == policy->max)
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
limits->max_perf_ctl = control;
if (control * cpu->pstate.scaling == policy->min)
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
limits->min_perf_ctl = control;
}
pr_debug("intel_pstate: max %u policy_max %u perf_ctl [0x%x-0x%x]\n",
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
policy->cpuinfo.max_freq, policy->max, limits->min_perf_ctl,
limits->max_perf_ctl);
#endif
if (hwp_active)
intel_pstate_hwp_set();
return 0;
}
static int intel_pstate_verify_policy(struct cpufreq_policy *policy)
{
cpufreq_verify_within_cpu_limits(policy);
if (policy->policy != CPUFREQ_POLICY_POWERSAVE &&
policy->policy != CPUFREQ_POLICY_PERFORMANCE)
return -EINVAL;
return 0;
}
static void intel_pstate_stop_cpu(struct cpufreq_policy *policy)
{
int cpu_num = policy->cpu;
struct cpudata *cpu = all_cpu_data[cpu_num];
pr_debug("intel_pstate: CPU %d exiting\n", cpu_num);
del_timer_sync(&all_cpu_data[cpu_num]->timer);
if (hwp_active)
return;
intel_pstate_set_pstate(cpu, cpu->pstate.min_pstate, false);
}
static int intel_pstate_cpu_init(struct cpufreq_policy *policy)
{
struct cpudata *cpu;
int rc;
rc = intel_pstate_init_cpu(policy->cpu);
if (rc)
return rc;
cpu = all_cpu_data[policy->cpu];
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value On systems that initialize the intel_pstate driver with the performance governor, and then switch to the powersave governor will not transition to lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct is set to a low value. The behavior of governor switching changed after commit a04759924e25 ("[cpufreq] intel_pstate: honor user space min_perf_pct override on resume"). The commit introduced tracking of performance percentage changes via sysfs in order to restore userspace changes during suspend/resume. The problem occurs because the global values of the newly introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor change and this causes the powersave governor to inherit the performance governor's settings. A simple change would have been to reset max_sysfs_pct to 100 and min_sysfs_pct to 0 on a governor change, which fixes the problem with governor switching. However, since we cannot break userspace[1] the fix is now to give each governor its own limits storage area so that governor specific changes are tracked. I successfully tested this by booting with both the performance governor and the powersave governor by default, and switching between the two governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values, and looking at the output of cpupower frequency-info). Suspend/Resume testing was performed by Doug Smythies. [1] Systems which suspend/resume using the unmaintained pm-utils package will always transition to the performance governor before the suspend and after the resume. This means a system using the powersave governor will go from powersave to performance, then suspend/resume, performance to powersave. The simple change during governor changes would have been overwritten when the governor changed before and after the suspend/resume. I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225 against Fedora to remove the 94cpufreq file that causes the problem. It should be noted that pm-utils is obsoleted with newer versions of systemd. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-10-15 14:34:15 +03:00
if (limits->min_perf_pct == 100 && limits->max_perf_pct == 100)
policy->policy = CPUFREQ_POLICY_PERFORMANCE;
else
policy->policy = CPUFREQ_POLICY_POWERSAVE;
policy->min = cpu->pstate.min_pstate * cpu->pstate.scaling;
policy->max = cpu->pstate.turbo_pstate * cpu->pstate.scaling;
/* cpuinfo and default policy values */
policy->cpuinfo.min_freq = cpu->pstate.min_pstate * cpu->pstate.scaling;
policy->cpuinfo.max_freq =
cpu->pstate.turbo_pstate * cpu->pstate.scaling;
if (!no_acpi_perf)
intel_pstate_init_perf_limits(policy);
/*
* If there is no acpi perf data or error, we ignore and use Intel P
* state calculated limits, So this is not fatal error.
*/
policy->cpuinfo.transition_latency = CPUFREQ_ETERNAL;
cpumask_set_cpu(policy->cpu, policy->cpus);
return 0;
}
static int intel_pstate_cpu_exit(struct cpufreq_policy *policy)
{
return intel_pstate_exit_perf_limits(policy);
}
static struct cpufreq_driver intel_pstate_driver = {
.flags = CPUFREQ_CONST_LOOPS,
.verify = intel_pstate_verify_policy,
.setpolicy = intel_pstate_set_policy,
.get = intel_pstate_get,
.init = intel_pstate_cpu_init,
.exit = intel_pstate_cpu_exit,
.stop_cpu = intel_pstate_stop_cpu,
.name = "intel_pstate",
};
static int __initdata no_load;
static int __initdata no_hwp;
static int __initdata hwp_only;
static unsigned int force_load;
static int intel_pstate_msrs_not_valid(void)
{
if (!pstate_funcs.get_max() ||
!pstate_funcs.get_min() ||
!pstate_funcs.get_turbo())
return -ENODEV;
return 0;
}
static void copy_pid_params(struct pstate_adjust_policy *policy)
{
pid_params.sample_rate_ms = policy->sample_rate_ms;
pid_params.p_gain_pct = policy->p_gain_pct;
pid_params.i_gain_pct = policy->i_gain_pct;
pid_params.d_gain_pct = policy->d_gain_pct;
pid_params.deadband = policy->deadband;
pid_params.setpoint = policy->setpoint;
}
static void copy_cpu_funcs(struct pstate_funcs *funcs)
{
pstate_funcs.get_max = funcs->get_max;
pstate_funcs.get_max_physical = funcs->get_max_physical;
pstate_funcs.get_min = funcs->get_min;
pstate_funcs.get_turbo = funcs->get_turbo;
pstate_funcs.get_scaling = funcs->get_scaling;
pstate_funcs.set = funcs->set;
pstate_funcs.get_vid = funcs->get_vid;
}
intel_pstate: skip the driver if ACPI has power mgmt option Do not load the Intel pstate driver if the platform firmware (ACPI BIOS) supports the power management alternatives. The ACPI BIOS indicates that the OS control mode can be used if the _PSS (Performance Supported States) is defined in ACPI table. For the OS control mode, the Intel pstate driver will be loaded. HP BIOS has several power management modes (firmware, OS-control and so on). For the OS control mode in HP BIOS, the Intel p-state driver will be loaded. When the customer chooses the firmware power management in HP BIOS, the Intel p-state driver will be ignored. I put hw_vendor_info vendor_info in case other vendors (Dell, Lenovo...) have their firmware power management. Vendors should make sure their firmware power management works properly, and they can go for adding their vendor info to the variable. I have verified the patch on HP ProLiant servers. The patch worked correctly. Signed-off-by: Adrian Huang <adrianhuang0701@gmail.com> [rjw: Fixed up !CONFIG_ACPI build] [Linda Knippers: As Adrian has recently left HP, I retested the updated patch on an HP ProLiant server and verified that it is behaving correctly. When the BIOS is configured for OS control for power management, the intel_pstate driver loads as expected. When the BIOS is configured to provide the power management, the intel_pstate driver does not load and we get the pcc_cpufreq driver instead.] Signed-off-by: Linda Knippers <linda.knippers@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-10-31 19:24:05 +04:00
#if IS_ENABLED(CONFIG_ACPI)
static bool intel_pstate_no_acpi_pss(void)
{
int i;
for_each_possible_cpu(i) {
acpi_status status;
union acpi_object *pss;
struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
struct acpi_processor *pr = per_cpu(processors, i);
if (!pr)
continue;
status = acpi_evaluate_object(pr->handle, "_PSS", NULL, &buffer);
if (ACPI_FAILURE(status))
continue;
pss = buffer.pointer;
if (pss && pss->type == ACPI_TYPE_PACKAGE) {
kfree(pss);
return false;
}
kfree(pss);
}
return true;
}
static bool intel_pstate_has_acpi_ppc(void)
{
int i;
for_each_possible_cpu(i) {
struct acpi_processor *pr = per_cpu(processors, i);
if (!pr)
continue;
if (acpi_has_method(pr->handle, "_PPC"))
return true;
}
return false;
}
enum {
PSS,
PPC,
};
intel_pstate: skip the driver if ACPI has power mgmt option Do not load the Intel pstate driver if the platform firmware (ACPI BIOS) supports the power management alternatives. The ACPI BIOS indicates that the OS control mode can be used if the _PSS (Performance Supported States) is defined in ACPI table. For the OS control mode, the Intel pstate driver will be loaded. HP BIOS has several power management modes (firmware, OS-control and so on). For the OS control mode in HP BIOS, the Intel p-state driver will be loaded. When the customer chooses the firmware power management in HP BIOS, the Intel p-state driver will be ignored. I put hw_vendor_info vendor_info in case other vendors (Dell, Lenovo...) have their firmware power management. Vendors should make sure their firmware power management works properly, and they can go for adding their vendor info to the variable. I have verified the patch on HP ProLiant servers. The patch worked correctly. Signed-off-by: Adrian Huang <adrianhuang0701@gmail.com> [rjw: Fixed up !CONFIG_ACPI build] [Linda Knippers: As Adrian has recently left HP, I retested the updated patch on an HP ProLiant server and verified that it is behaving correctly. When the BIOS is configured for OS control for power management, the intel_pstate driver loads as expected. When the BIOS is configured to provide the power management, the intel_pstate driver does not load and we get the pcc_cpufreq driver instead.] Signed-off-by: Linda Knippers <linda.knippers@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-10-31 19:24:05 +04:00
struct hw_vendor_info {
u16 valid;
char oem_id[ACPI_OEM_ID_SIZE];
char oem_table_id[ACPI_OEM_TABLE_ID_SIZE];
int oem_pwr_table;
intel_pstate: skip the driver if ACPI has power mgmt option Do not load the Intel pstate driver if the platform firmware (ACPI BIOS) supports the power management alternatives. The ACPI BIOS indicates that the OS control mode can be used if the _PSS (Performance Supported States) is defined in ACPI table. For the OS control mode, the Intel pstate driver will be loaded. HP BIOS has several power management modes (firmware, OS-control and so on). For the OS control mode in HP BIOS, the Intel p-state driver will be loaded. When the customer chooses the firmware power management in HP BIOS, the Intel p-state driver will be ignored. I put hw_vendor_info vendor_info in case other vendors (Dell, Lenovo...) have their firmware power management. Vendors should make sure their firmware power management works properly, and they can go for adding their vendor info to the variable. I have verified the patch on HP ProLiant servers. The patch worked correctly. Signed-off-by: Adrian Huang <adrianhuang0701@gmail.com> [rjw: Fixed up !CONFIG_ACPI build] [Linda Knippers: As Adrian has recently left HP, I retested the updated patch on an HP ProLiant server and verified that it is behaving correctly. When the BIOS is configured for OS control for power management, the intel_pstate driver loads as expected. When the BIOS is configured to provide the power management, the intel_pstate driver does not load and we get the pcc_cpufreq driver instead.] Signed-off-by: Linda Knippers <linda.knippers@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-10-31 19:24:05 +04:00
};
/* Hardware vendor-specific info that has its own power management modes */
static struct hw_vendor_info vendor_info[] = {
{1, "HP ", "ProLiant", PSS},
{1, "ORACLE", "X4-2 ", PPC},
{1, "ORACLE", "X4-2L ", PPC},
{1, "ORACLE", "X4-2B ", PPC},
{1, "ORACLE", "X3-2 ", PPC},
{1, "ORACLE", "X3-2L ", PPC},
{1, "ORACLE", "X3-2B ", PPC},
{1, "ORACLE", "X4470M2 ", PPC},
{1, "ORACLE", "X4270M3 ", PPC},
{1, "ORACLE", "X4270M2 ", PPC},
{1, "ORACLE", "X4170M2 ", PPC},
{1, "ORACLE", "X4170 M3", PPC},
{1, "ORACLE", "X4275 M3", PPC},
{1, "ORACLE", "X6-2 ", PPC},
{1, "ORACLE", "Sudbury ", PPC},
intel_pstate: skip the driver if ACPI has power mgmt option Do not load the Intel pstate driver if the platform firmware (ACPI BIOS) supports the power management alternatives. The ACPI BIOS indicates that the OS control mode can be used if the _PSS (Performance Supported States) is defined in ACPI table. For the OS control mode, the Intel pstate driver will be loaded. HP BIOS has several power management modes (firmware, OS-control and so on). For the OS control mode in HP BIOS, the Intel p-state driver will be loaded. When the customer chooses the firmware power management in HP BIOS, the Intel p-state driver will be ignored. I put hw_vendor_info vendor_info in case other vendors (Dell, Lenovo...) have their firmware power management. Vendors should make sure their firmware power management works properly, and they can go for adding their vendor info to the variable. I have verified the patch on HP ProLiant servers. The patch worked correctly. Signed-off-by: Adrian Huang <adrianhuang0701@gmail.com> [rjw: Fixed up !CONFIG_ACPI build] [Linda Knippers: As Adrian has recently left HP, I retested the updated patch on an HP ProLiant server and verified that it is behaving correctly. When the BIOS is configured for OS control for power management, the intel_pstate driver loads as expected. When the BIOS is configured to provide the power management, the intel_pstate driver does not load and we get the pcc_cpufreq driver instead.] Signed-off-by: Linda Knippers <linda.knippers@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-10-31 19:24:05 +04:00
{0, "", ""},
};
static bool intel_pstate_platform_pwr_mgmt_exists(void)
{
struct acpi_table_header hdr;
struct hw_vendor_info *v_info;
const struct x86_cpu_id *id;
u64 misc_pwr;
id = x86_match_cpu(intel_pstate_cpu_oob_ids);
if (id) {
rdmsrl(MSR_MISC_PWR_MGMT, misc_pwr);
if ( misc_pwr & (1 << 8))
return true;
}
intel_pstate: skip the driver if ACPI has power mgmt option Do not load the Intel pstate driver if the platform firmware (ACPI BIOS) supports the power management alternatives. The ACPI BIOS indicates that the OS control mode can be used if the _PSS (Performance Supported States) is defined in ACPI table. For the OS control mode, the Intel pstate driver will be loaded. HP BIOS has several power management modes (firmware, OS-control and so on). For the OS control mode in HP BIOS, the Intel p-state driver will be loaded. When the customer chooses the firmware power management in HP BIOS, the Intel p-state driver will be ignored. I put hw_vendor_info vendor_info in case other vendors (Dell, Lenovo...) have their firmware power management. Vendors should make sure their firmware power management works properly, and they can go for adding their vendor info to the variable. I have verified the patch on HP ProLiant servers. The patch worked correctly. Signed-off-by: Adrian Huang <adrianhuang0701@gmail.com> [rjw: Fixed up !CONFIG_ACPI build] [Linda Knippers: As Adrian has recently left HP, I retested the updated patch on an HP ProLiant server and verified that it is behaving correctly. When the BIOS is configured for OS control for power management, the intel_pstate driver loads as expected. When the BIOS is configured to provide the power management, the intel_pstate driver does not load and we get the pcc_cpufreq driver instead.] Signed-off-by: Linda Knippers <linda.knippers@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-10-31 19:24:05 +04:00
if (acpi_disabled ||
ACPI_FAILURE(acpi_get_table_header(ACPI_SIG_FADT, 0, &hdr)))
intel_pstate: skip the driver if ACPI has power mgmt option Do not load the Intel pstate driver if the platform firmware (ACPI BIOS) supports the power management alternatives. The ACPI BIOS indicates that the OS control mode can be used if the _PSS (Performance Supported States) is defined in ACPI table. For the OS control mode, the Intel pstate driver will be loaded. HP BIOS has several power management modes (firmware, OS-control and so on). For the OS control mode in HP BIOS, the Intel p-state driver will be loaded. When the customer chooses the firmware power management in HP BIOS, the Intel p-state driver will be ignored. I put hw_vendor_info vendor_info in case other vendors (Dell, Lenovo...) have their firmware power management. Vendors should make sure their firmware power management works properly, and they can go for adding their vendor info to the variable. I have verified the patch on HP ProLiant servers. The patch worked correctly. Signed-off-by: Adrian Huang <adrianhuang0701@gmail.com> [rjw: Fixed up !CONFIG_ACPI build] [Linda Knippers: As Adrian has recently left HP, I retested the updated patch on an HP ProLiant server and verified that it is behaving correctly. When the BIOS is configured for OS control for power management, the intel_pstate driver loads as expected. When the BIOS is configured to provide the power management, the intel_pstate driver does not load and we get the pcc_cpufreq driver instead.] Signed-off-by: Linda Knippers <linda.knippers@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-10-31 19:24:05 +04:00
return false;
for (v_info = vendor_info; v_info->valid; v_info++) {
if (!strncmp(hdr.oem_id, v_info->oem_id, ACPI_OEM_ID_SIZE) &&
!strncmp(hdr.oem_table_id, v_info->oem_table_id,
ACPI_OEM_TABLE_ID_SIZE))
switch (v_info->oem_pwr_table) {
case PSS:
return intel_pstate_no_acpi_pss();
case PPC:
return intel_pstate_has_acpi_ppc() &&
(!force_load);
}
intel_pstate: skip the driver if ACPI has power mgmt option Do not load the Intel pstate driver if the platform firmware (ACPI BIOS) supports the power management alternatives. The ACPI BIOS indicates that the OS control mode can be used if the _PSS (Performance Supported States) is defined in ACPI table. For the OS control mode, the Intel pstate driver will be loaded. HP BIOS has several power management modes (firmware, OS-control and so on). For the OS control mode in HP BIOS, the Intel p-state driver will be loaded. When the customer chooses the firmware power management in HP BIOS, the Intel p-state driver will be ignored. I put hw_vendor_info vendor_info in case other vendors (Dell, Lenovo...) have their firmware power management. Vendors should make sure their firmware power management works properly, and they can go for adding their vendor info to the variable. I have verified the patch on HP ProLiant servers. The patch worked correctly. Signed-off-by: Adrian Huang <adrianhuang0701@gmail.com> [rjw: Fixed up !CONFIG_ACPI build] [Linda Knippers: As Adrian has recently left HP, I retested the updated patch on an HP ProLiant server and verified that it is behaving correctly. When the BIOS is configured for OS control for power management, the intel_pstate driver loads as expected. When the BIOS is configured to provide the power management, the intel_pstate driver does not load and we get the pcc_cpufreq driver instead.] Signed-off-by: Linda Knippers <linda.knippers@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-10-31 19:24:05 +04:00
}
return false;
}
#else /* CONFIG_ACPI not enabled */
static inline bool intel_pstate_platform_pwr_mgmt_exists(void) { return false; }
static inline bool intel_pstate_has_acpi_ppc(void) { return false; }
intel_pstate: skip the driver if ACPI has power mgmt option Do not load the Intel pstate driver if the platform firmware (ACPI BIOS) supports the power management alternatives. The ACPI BIOS indicates that the OS control mode can be used if the _PSS (Performance Supported States) is defined in ACPI table. For the OS control mode, the Intel pstate driver will be loaded. HP BIOS has several power management modes (firmware, OS-control and so on). For the OS control mode in HP BIOS, the Intel p-state driver will be loaded. When the customer chooses the firmware power management in HP BIOS, the Intel p-state driver will be ignored. I put hw_vendor_info vendor_info in case other vendors (Dell, Lenovo...) have their firmware power management. Vendors should make sure their firmware power management works properly, and they can go for adding their vendor info to the variable. I have verified the patch on HP ProLiant servers. The patch worked correctly. Signed-off-by: Adrian Huang <adrianhuang0701@gmail.com> [rjw: Fixed up !CONFIG_ACPI build] [Linda Knippers: As Adrian has recently left HP, I retested the updated patch on an HP ProLiant server and verified that it is behaving correctly. When the BIOS is configured for OS control for power management, the intel_pstate driver loads as expected. When the BIOS is configured to provide the power management, the intel_pstate driver does not load and we get the pcc_cpufreq driver instead.] Signed-off-by: Linda Knippers <linda.knippers@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-10-31 19:24:05 +04:00
#endif /* CONFIG_ACPI */
static int __init intel_pstate_init(void)
{
int cpu, rc = 0;
const struct x86_cpu_id *id;
struct cpu_defaults *cpu_def;
if (no_load)
return -ENODEV;
id = x86_match_cpu(intel_pstate_cpu_ids);
if (!id)
return -ENODEV;
intel_pstate: skip the driver if ACPI has power mgmt option Do not load the Intel pstate driver if the platform firmware (ACPI BIOS) supports the power management alternatives. The ACPI BIOS indicates that the OS control mode can be used if the _PSS (Performance Supported States) is defined in ACPI table. For the OS control mode, the Intel pstate driver will be loaded. HP BIOS has several power management modes (firmware, OS-control and so on). For the OS control mode in HP BIOS, the Intel p-state driver will be loaded. When the customer chooses the firmware power management in HP BIOS, the Intel p-state driver will be ignored. I put hw_vendor_info vendor_info in case other vendors (Dell, Lenovo...) have their firmware power management. Vendors should make sure their firmware power management works properly, and they can go for adding their vendor info to the variable. I have verified the patch on HP ProLiant servers. The patch worked correctly. Signed-off-by: Adrian Huang <adrianhuang0701@gmail.com> [rjw: Fixed up !CONFIG_ACPI build] [Linda Knippers: As Adrian has recently left HP, I retested the updated patch on an HP ProLiant server and verified that it is behaving correctly. When the BIOS is configured for OS control for power management, the intel_pstate driver loads as expected. When the BIOS is configured to provide the power management, the intel_pstate driver does not load and we get the pcc_cpufreq driver instead.] Signed-off-by: Linda Knippers <linda.knippers@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-10-31 19:24:05 +04:00
/*
* The Intel pstate driver will be ignored if the platform
* firmware has its own power management modes.
*/
if (intel_pstate_platform_pwr_mgmt_exists())
return -ENODEV;
cpu_def = (struct cpu_defaults *)id->driver_data;
copy_pid_params(&cpu_def->pid_policy);
copy_cpu_funcs(&cpu_def->funcs);
if (intel_pstate_msrs_not_valid())
return -ENODEV;
pr_info("Intel P-state driver initializing.\n");
all_cpu_data = vzalloc(sizeof(void *) * num_possible_cpus());
if (!all_cpu_data)
return -ENOMEM;
if (static_cpu_has_safe(X86_FEATURE_HWP) && !no_hwp)
hwp_active++;
if (!hwp_active && hwp_only)
goto out;
rc = cpufreq_register_driver(&intel_pstate_driver);
if (rc)
goto out;
intel_pstate_debug_expose_params();
intel_pstate_sysfs_expose_params();
return rc;
out:
get_online_cpus();
for_each_online_cpu(cpu) {
if (all_cpu_data[cpu]) {
del_timer_sync(&all_cpu_data[cpu]->timer);
kfree(all_cpu_data[cpu]);
}
}
put_online_cpus();
vfree(all_cpu_data);
return -ENODEV;
}
device_initcall(intel_pstate_init);
static int __init intel_pstate_setup(char *str)
{
if (!str)
return -EINVAL;
if (!strcmp(str, "disable"))
no_load = 1;
if (!strcmp(str, "no_hwp"))
no_hwp = 1;
if (!strcmp(str, "force"))
force_load = 1;
if (!strcmp(str, "hwp_only"))
hwp_only = 1;
if (!strcmp(str, "no_acpi"))
no_acpi_perf = 1;
return 0;
}
early_param("intel_pstate", intel_pstate_setup);
MODULE_AUTHOR("Dirk Brandewie <dirk.j.brandewie@intel.com>");
MODULE_DESCRIPTION("'intel_pstate' - P state driver Intel Core processors");
MODULE_LICENSE("GPL");