WSL2-Linux-Kernel/drivers/ata/pata_cypress.c

/*
 * pata_cypress.c 	- Cypress PATA for new ATA layer
 *			  (C) 2006 Red Hat Inc
 *			  Alan Cox <alan@redhat.com>
 *
 * Based heavily on
 * linux/drivers/ide/pci/cy82c693.c		Version 0.40	Sep. 10, 2002
 *
 */

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>

#define DRV_NAME "pata_cypress"
#define DRV_VERSION "0.1.5"

/* here are the offset definitions for the registers */

enum {
	CY82_IDE_CMDREG		= 0x04,
	CY82_IDE_ADDRSETUP	= 0x48,
	CY82_IDE_MASTER_IOR	= 0x4C,
	CY82_IDE_MASTER_IOW	= 0x4D,
	CY82_IDE_SLAVE_IOR	= 0x4E,
	CY82_IDE_SLAVE_IOW	= 0x4F,
	CY82_IDE_MASTER_8BIT	= 0x50,
	CY82_IDE_SLAVE_8BIT	= 0x51,

	CY82_INDEX_PORT		= 0x22,
	CY82_DATA_PORT		= 0x23,

	CY82_INDEX_CTRLREG1	= 0x01,
	CY82_INDEX_CHANNEL0	= 0x30,
	CY82_INDEX_CHANNEL1	= 0x31,
	CY82_INDEX_TIMEOUT	= 0x32
};

/**
 *	cy82c693_set_piomode	-	set initial PIO mode data
 *	@ap: ATA interface
 *	@adev: ATA device
 *
 *	Called to do the PIO mode setup.
 */

static void cy82c693_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	struct ata_timing t;
	const unsigned long T = 1000000 / 33;
	short time_16, time_8;
	u32 addr;

	if (ata_timing_compute(adev, adev->pio_mode, &t, T, 1) < 0) {
		printk(KERN_ERR DRV_NAME ": mome computation failed.\n");
		return;
	}

	time_16 = clamp_val(t.recover, 0, 15) | (clamp_val(t.active, 0, 15) << 4);
	time_8 = clamp_val(t.act8b, 0, 15) | (clamp_val(t.rec8b, 0, 15) << 4);

	if (adev->devno == 0) {
		pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr);

		addr &= ~0x0F;	/* Mask bits */
		addr |= clamp_val(t.setup, 0, 15);

		pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr);
		pci_write_config_byte(pdev, CY82_IDE_MASTER_IOR, time_16);
		pci_write_config_byte(pdev, CY82_IDE_MASTER_IOW, time_16);
		pci_write_config_byte(pdev, CY82_IDE_MASTER_8BIT, time_8);
	} else {
		pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr);

		addr &= ~0xF0;	/* Mask bits */
		addr |= (clamp_val(t.setup, 0, 15) << 4);

		pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr);
		pci_write_config_byte(pdev, CY82_IDE_SLAVE_IOR, time_16);
		pci_write_config_byte(pdev, CY82_IDE_SLAVE_IOW, time_16);
		pci_write_config_byte(pdev, CY82_IDE_SLAVE_8BIT, time_8);
	}
}

/**
 *	cy82c693_set_dmamode	-	set initial DMA mode data
 *	@ap: ATA interface
 *	@adev: ATA device
 *
 *	Called to do the DMA mode setup.
 */

static void cy82c693_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
	int reg = CY82_INDEX_CHANNEL0 + ap->port_no;

	/* Be afraid, be very afraid. Magic registers  in low I/O space */
	outb(reg, 0x22);
	outb(adev->dma_mode - XFER_MW_DMA_0, 0x23);

	/* 0x50 gives the best behaviour on the Alpha's using this chip */
	outb(CY82_INDEX_TIMEOUT, 0x22);
	outb(0x50, 0x23);
}

static struct scsi_host_template cy82c693_sht = {
	ATA_BMDMA_SHT(DRV_NAME),
};

static struct ata_port_operations cy82c693_port_ops = {
	.inherits	= &ata_bmdma_port_ops,
	.cable_detect	= ata_cable_40wire,
	.set_piomode	= cy82c693_set_piomode,
	.set_dmamode	= cy82c693_set_dmamode,
};

static int cy82c693_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
	static const struct ata_port_info info = {
		.flags = ATA_FLAG_SLAVE_POSS,
		.pio_mask = 0x1f,
		.mwdma_mask = 0x07,
		.port_ops = &cy82c693_port_ops
	};
	const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };

	/* Devfn 1 is the ATA primary. The secondary is magic and on devfn2.
	   For the moment we don't handle the secondary. FIXME */

	if (PCI_FUNC(pdev->devfn) != 1)
		return -ENODEV;

	return ata_pci_sff_init_one(pdev, ppi, &cy82c693_sht, NULL);
}

static const struct pci_device_id cy82c693[] = {
	{ PCI_VDEVICE(CONTAQ, PCI_DEVICE_ID_CONTAQ_82C693), },

	{ },
};

static struct pci_driver cy82c693_pci_driver = {
	.name 		= DRV_NAME,
	.id_table	= cy82c693,
	.probe 		= cy82c693_init_one,
	.remove		= ata_pci_remove_one,
#ifdef CONFIG_PM
	.suspend	= ata_pci_device_suspend,
	.resume		= ata_pci_device_resume,
#endif
};

static int __init cy82c693_init(void)
{
	return pci_register_driver(&cy82c693_pci_driver);
}


static void __exit cy82c693_exit(void)
{
	pci_unregister_driver(&cy82c693_pci_driver);
}


MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the CY82C693 PATA controller");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, cy82c693);
MODULE_VERSION(DRV_VERSION);

module_init(cy82c693_init);
module_exit(cy82c693_exit);