mtd: spi-nor: spansion: Rework spi_nor_cypress_octal_dtr_enable()

Introduce template operation to remove code duplication.
Split spi_nor_cypress_octal_dtr_enable() in
spi_nor_cypress_octal_dtr_ena() spi_nor_cypress_octal_dtr_dis() as it no
longer made sense to try to keep everything alltogether: too many
"if (enable)" throughout the code, which made the code difficult to read.
Add debug messages in case spi_nor_read_id() fails.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-9-tudor.ambarus@microchip.com
This commit is contained in:
Tudor Ambarus 2022-04-20 13:34:24 +03:00 коммит произвёл Pratyush Yadav
Родитель 4629adaff7
Коммит 27ff0d34fb
1 изменённых файлов: 84 добавлений и 74 удалений

Просмотреть файл

@ -23,6 +23,88 @@
#define SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_DS 0
#define SPINOR_OP_CYPRESS_RD_FAST 0xee
/* Cypress SPI NOR flash operations. */
#define CYPRESS_NOR_WR_ANY_REG_OP(naddr, addr, ndata, buf) \
SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 0), \
SPI_MEM_OP_ADDR(naddr, addr, 0), \
SPI_MEM_OP_NO_DUMMY, \
SPI_MEM_OP_DATA_OUT(ndata, buf, 0))
static int cypress_nor_octal_dtr_en(struct spi_nor *nor)
{
struct spi_mem_op op;
u8 *buf = nor->bouncebuf;
int ret;
/* Use 24 dummy cycles for memory array reads. */
*buf = SPINOR_REG_CYPRESS_CFR2V_MEMLAT_11_24;
op = (struct spi_mem_op)
CYPRESS_NOR_WR_ANY_REG_OP(3, SPINOR_REG_CYPRESS_CFR2V, 1, buf);
ret = spi_nor_write_any_volatile_reg(nor, &op, nor->reg_proto);
if (ret)
return ret;
ret = spi_nor_wait_till_ready(nor);
if (ret)
return ret;
nor->read_dummy = 24;
/* Set the octal and DTR enable bits. */
buf[0] = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN;
op = (struct spi_mem_op)
CYPRESS_NOR_WR_ANY_REG_OP(3, SPINOR_REG_CYPRESS_CFR5V, 1, buf);
ret = spi_nor_write_any_volatile_reg(nor, &op, nor->reg_proto);
if (ret)
return ret;
/* Read flash ID to make sure the switch was successful. */
ret = spi_nor_read_id(nor, 4, 3, buf, SNOR_PROTO_8_8_8_DTR);
if (ret) {
dev_dbg(nor->dev, "error %d reading JEDEC ID after enabling 8D-8D-8D mode\n", ret);
return ret;
}
if (memcmp(buf, nor->info->id, nor->info->id_len))
return -EINVAL;
return 0;
}
static int cypress_nor_octal_dtr_dis(struct spi_nor *nor)
{
struct spi_mem_op op;
u8 *buf = nor->bouncebuf;
int ret;
/*
* The register is 1-byte wide, but 1-byte transactions are not allowed
* in 8D-8D-8D mode. Since there is no register at the next location,
* just initialize the value to 0 and let the transaction go on.
*/
buf[0] = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_DS;
buf[1] = 0;
op = (struct spi_mem_op)
CYPRESS_NOR_WR_ANY_REG_OP(4, SPINOR_REG_CYPRESS_CFR5V, 2, buf);
ret = spi_nor_write_any_volatile_reg(nor, &op, SNOR_PROTO_8_8_8_DTR);
if (ret)
return ret;
/* Read flash ID to make sure the switch was successful. */
ret = spi_nor_read_id(nor, 0, 0, buf, SNOR_PROTO_1_1_1);
if (ret) {
dev_dbg(nor->dev, "error %d reading JEDEC ID after disabling 8D-8D-8D mode\n", ret);
return ret;
}
if (memcmp(buf, nor->info->id, nor->info->id_len))
return -EINVAL;
return 0;
}
/**
* cypress_nor_octal_dtr_enable() - Enable octal DTR on Cypress flashes.
* @nor: pointer to a 'struct spi_nor'
@ -35,80 +117,8 @@
*/
static int cypress_nor_octal_dtr_enable(struct spi_nor *nor, bool enable)
{
struct spi_mem_op op;
u8 *buf = nor->bouncebuf;
int ret;
if (enable) {
/* Use 24 dummy cycles for memory array reads. */
ret = spi_nor_write_enable(nor);
if (ret)
return ret;
*buf = SPINOR_REG_CYPRESS_CFR2V_MEMLAT_11_24;
op = (struct spi_mem_op)
SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
SPI_MEM_OP_ADDR(3, SPINOR_REG_CYPRESS_CFR2V,
1),
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_DATA_OUT(1, buf, 1));
ret = spi_mem_exec_op(nor->spimem, &op);
if (ret)
return ret;
ret = spi_nor_wait_till_ready(nor);
if (ret)
return ret;
nor->read_dummy = 24;
}
/* Set/unset the octal and DTR enable bits. */
ret = spi_nor_write_enable(nor);
if (ret)
return ret;
if (enable) {
buf[0] = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN;
} else {
/*
* The register is 1-byte wide, but 1-byte transactions are not
* allowed in 8D-8D-8D mode. Since there is no register at the
* next location, just initialize the value to 0 and let the
* transaction go on.
*/
buf[0] = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_DS;
buf[1] = 0;
}
op = (struct spi_mem_op)
SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
SPI_MEM_OP_ADDR(enable ? 3 : 4,
SPINOR_REG_CYPRESS_CFR5V,
1),
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_DATA_OUT(enable ? 1 : 2, buf, 1));
if (!enable)
spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
ret = spi_mem_exec_op(nor->spimem, &op);
if (ret)
return ret;
/* Read flash ID to make sure the switch was successful. */
if (enable)
ret = spi_nor_read_id(nor, 4, 3, buf, SNOR_PROTO_8_8_8_DTR);
else
ret = spi_nor_read_id(nor, 0, 0, buf, SNOR_PROTO_1_1_1);
if (ret)
return ret;
if (memcmp(buf, nor->info->id, nor->info->id_len))
return -EINVAL;
return 0;
return enable ? cypress_nor_octal_dtr_en(nor) :
cypress_nor_octal_dtr_dis(nor);
}
static void s28hs512t_default_init(struct spi_nor *nor)