ARM: SoC device tree updates for 5.1

This is a smaller update than the past few times, but with just over 500 non-merge changesets still dwarfes the rest of the SoC tree. Three new SoC platforms get added, each one a follow-up to an existing product, and added here in combination with a reference platform: - Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging processor https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html - Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for Rich Graphics Applications". https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html - NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X These are actual commercial products we now support with an in-kernel device tree source file: - Bosch Guardian is a product made by Bosch Power Tools GmbH, based on the Texas Instruments AM335x chip - Winterland IceBoard is a Texas Instruments AM3874 based machine used in telescopes at the south pole and elsewhere, see commit d031773169 for some pointers: - Inspur on5263m5 is an x86 server platform with an Aspeed ast2500 baseboard management controller. This is for running on the BMC. - Zodiac Digital Tapping Unit, apparently a kind of ethernet switch used in airplanes. - Phicomm K3 is a WiFi router based on Broadcom bcm47094 - Methode Electronics uDPU FTTdp distribution point unit - X96 Max, a generic TV box based on Amlogic G12a (S905X2) - NVIDIA Shield TV (Darcy) based on Tegra210 And then there are several new SBC, evaluation, development or modular systems that we add: - Three new Rockchips rk3399 based boards: - FriendlyElec NanoPC-T4 and NanoPi M4 - Radxa ROCK Pi 4 - Five new i.MX6 family SoM modules and boards for industrial products: - Logic PD i.MX6QD SoM and evaluation baseboad - Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL - Phytec phyCORE i.MX6 UltraLite SoM and evaluation module - MYIR Tech MYD-LPC4357 development based on the NXP lpc4357 microcontroller - Chameleon96, an Intel/Altera Cyclone5 based FPGA development system in 96boards form factor - Arm Fixed Virtual Platforms(FVP) Base RevC, a purely virtual platform for corresponding to the latest "fast model" - Another Raspberry Pi variant: Model 3 A+, supported both in 32-bit and 64-bit mode. - Oxalis Evalkit V100 based on NXP Layerscape LS1012a, in 96Boards enterprise form factor - Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108 For already supported boards and SoCs, we often add support for new devices after merging the drivers. This time, the largest changes include updates for - STMicroelectronics stm32mp1, which was now formally launched last week - Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip - Action Semi S700 - TI AM654x, their recently merged 64-bit SoC from the OMAP family - Various Amlogic Meson SoCs - Mediatek MT2712 - NVIDIA Tegra186 and Tegra210 - The ancient NXP lpc32xx family - Samsung s5pv210, used in some older mobile phones Many other chips see smaller updates and bugfixes beyond that. Signed-off-by: Arnd Bergmann <arnd@arndb.de> -----BEGIN PGP SIGNATURE----- Version: GnuPG v2 iQIcBAABCAAGBQJcf9c1AAoJEGCrR//JCVInvl8QAIgmK09QZr3VAD5WnKSoWwiX GP1+qgmr/cbIF9X+Kt/0Y2E+oIi9uxu7v5iwpYf0inzV4QOKwy9LvpeInd7s07bf hSPMN0wZ9bV5Ylk0YtlvGvOQTqys9oweeSEkHfjQ8Jm7aFkaRXQ1dt23d8KLILoB 8GKk9A4ncn1AB1vu6xBqeqBiaQiqhMjb9paWkmjYrjhP22hHlVyGlMd8cwfG+A5a 5Ft4lWkzvgrXPMwZgrCGU233OV5UHrn2A8ohiIUN5J6aSWxu8eMEryU+MF0poidl malJ+AHl2mK83YN3wYemxy/lEJzAW4PrjCVgY2bRDqwlOnI3+d+z7rVSfuMCzSKs TDTbv9VqPJhsZFr/GIkvB3iwnYfvP/mXrzM7gbw7rQqthEKOy+3HtZwmHAKF4QNK TT4wyngC/CwiyULEwtPCjbxZ/7yal6sygllioCo+M2OHeattIQEnqi/Yvc0vx/th th9Pepf26jUp/ZJNlxk0XDyBMPhUf6sHUvh7a+y6l6ZxZ6avbFdGPeJrQe5HF2Sp KM7BH3w/CpoNRSKs37mR7JpNdYNDSonItgaIm5xVJZk+Wr/BWgtcr6BbGD/vlT7N kIDDinyhczhvhpTmWs6QZdZNQmf6bASzTVeFv2+ES+kXt/AKhv0O5N4Pw/oU+VBv pD5+7YjjA0fMKcYae3gs =1goV -----END PGP SIGNATURE----- Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC device tree updates from Arnd Bergmann: "This is a smaller update than the past few times, but with just over 500 non-merge changesets still dwarfes the rest of the SoC tree. Three new SoC platforms get added, each one a follow-up to an existing product, and added here in combination with a reference platform: - Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging processor: https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html - Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for Rich Graphics Applications": https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html - NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC: https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X These are actual commercial products we now support with an in-kernel device tree source file: - Bosch Guardian is a product made by Bosch Power Tools GmbH, based on the Texas Instruments AM335x chip - Winterland IceBoard is a Texas Instruments AM3874 based machine used in telescopes at the south pole and elsewhere, see commit d031773169 for some pointers: - Inspur on5263m5 is an x86 server platform with an Aspeed ast2500 baseboard management controller. This is for running on the BMC. - Zodiac Digital Tapping Unit, apparently a kind of ethernet switch used in airplanes. - Phicomm K3 is a WiFi router based on Broadcom bcm47094 - Methode Electronics uDPU FTTdp distribution point unit - X96 Max, a generic TV box based on Amlogic G12a (S905X2) - NVIDIA Shield TV (Darcy) based on Tegra210 And then there are several new SBC, evaluation, development or modular systems that we add: - Three new Rockchips rk3399 based boards: - FriendlyElec NanoPC-T4 and NanoPi M4 - Radxa ROCK Pi 4 - Five new i.MX6 family SoM modules and boards for industrial products: - Logic PD i.MX6QD SoM and evaluation baseboad - Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL - Phytec phyCORE i.MX6 UltraLite SoM and evaluation module - MYIR Tech MYD-LPC4357 development based on the NXP lpc4357 microcontroller - Chameleon96, an Intel/Altera Cyclone5 based FPGA development system in 96boards form factor - Arm Fixed Virtual Platforms(FVP) Base RevC, a purely virtual platform for corresponding to the latest "fast model" - Another Raspberry Pi variant: Model 3 A+, supported both in 32-bit and 64-bit mode. - Oxalis Evalkit V100 based on NXP Layerscape LS1012a, in 96Boards enterprise form factor - Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108 For already supported boards and SoCs, we often add support for new devices after merging the drivers. This time, the largest changes include updates for - STMicroelectronics stm32mp1, which was now formally launched last week - Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip - Action Semi S700 - TI AM654x, their recently merged 64-bit SoC from the OMAP family - Various Amlogic Meson SoCs - Mediatek MT2712 - NVIDIA Tegra186 and Tegra210 - The ancient NXP lpc32xx family - Samsung s5pv210, used in some older mobile phones Many other chips see smaller updates and bugfixes beyond that" * tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (506 commits) ARM: dts: exynos: Fix max voltage for buck8 regulator on Odroid XU3/XU4 dt-bindings: net: ti: deprecate cpsw-phy-sel bindings ARM: dts: am335x: switch to use phy-gmii-sel ARM: dts: am4372: switch to use phy-gmii-sel ARM: dts: dm814x: switch to use phy-gmii-sel ARM: dts: dra7: switch to use phy-gmii-sel arch: arm: dts: kirkwood-rd88f6281: Remove disabled marvell,dsa reference ARM: dts: exynos: Add support for secondary DAI to Odroid XU4 ARM: dts: exynos: Add support for secondary DAI to Odroid XU3 ARM: dts: exynos: Disable ARM PMU on Odroid XU3-lite ARM: dts: exynos: Add stdout path property to Arndale board ARM: dts: exynos: Add minimal clkout parameters to Exynos3250 PMU ARM: dts: exynos: Enable ADC on Odroid HC1 arm64: dts: sprd: Remove wildcard compatible string arm64: dts: sprd: Add SC27XX fuel gauge device arm64: dts: sprd: Add SC2731 charger device arm64: dts: sprd: Add ADC calibration support arm64: dts: sprd: Remove PMIC INTC irq trigger type arm64: dts: rockchip: Enable tsadc device on rock960 ARM: dts: rockchip: add chosen node on veyron devices ...
2019-03-06 09:36:37 -08:00 · 2019-03-06 09:36:37 -08:00 · 6ad63dec9c
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@ -109,6 +109,7 @@ Board compatible values (alphabetically, grouped by SoC):
  - "amlogic,s400" (Meson axg a113d)

  - "amlogic,u200" (Meson g12a s905d2)
+  - "amediatech,x96-max" (Meson g12a s905x2)

 Amlogic Meson Firmware registers Interface
 ------------------------------------------
--- a/Documentation/devicetree/bindings/arm/armadeus.txt
+++ b/Documentation/devicetree/bindings/arm/armadeus.txt
@ -1,6 +0,0 @@
-Armadeus i.MX Platforms Device Tree Bindings
-----------------------------------------------
-
-APF51: i.MX51 based module.
-Required root node properties:
-    - compatible = "armadeus,imx51-apf51", "fsl,imx51";
--- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
+++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
@ -30,6 +30,10 @@ Raspberry Pi 2 Model B
 Required root node properties:
 compatible = "raspberrypi,2-model-b", "brcm,bcm2836";

+Raspberry Pi 3 Model A+
+Required root node properties:
+compatible = "raspberrypi,3-model-a-plus", "brcm,bcm2837";
+
 Raspberry Pi 3 Model B
 Required root node properties:
 compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
--- a/Documentation/devicetree/bindings/arm/bhf.txt
+++ b/Documentation/devicetree/bindings/arm/bhf.txt
@ -1,6 +0,0 @@
-Beckhoff Automation Platforms Device Tree Bindings
--------------------------------------------------
-
-CX9020 Embedded PC
-Required root node properties:
-    - compatible = "bhf,cx9020", "fsl,imx53";
--- a/Documentation/devicetree/bindings/arm/compulab-boards.txt
+++ b/Documentation/devicetree/bindings/arm/compulab-boards.txt
@ -1,25 +0,0 @@
-CompuLab SB-SOM is a multi-module baseboard capable of carrying:
- - CM-T43
- - CM-T54
- - CM-QS600
- - CL-SOM-AM57x
- - CL-SOM-iMX7
-modules with minor modifications to the SB-SOM assembly.
-
-Required root node properties:
-    - compatible = should be "compulab,sb-som"
-
-Compulab CL-SOM-iMX7 is a miniature System-on-Module (SoM) based on
-Freescale i.MX7 ARM Cortex-A7 System-on-Chip.
-
-Required root node properties:
-    - compatible = "compulab,cl-som-imx7", "fsl,imx7d";
-
-Compulab SBC-iMX7 is a single board computer based on the
-Freescale i.MX7 system-on-chip. SBC-iMX7 is implemented with
-the CL-SOM-iMX7 System-on-Module providing most of the functions,
-and SB-SOM-iMX7 carrier board providing additional peripheral
-functions and connectors.
-
-Required root node properties:
-    - compatible = "compulab,sbc-imx7", "compulab,cl-som-imx7", "fsl,imx7d";
--- a/Documentation/devicetree/bindings/arm/freescale/fsl,imx7ulp-sim.txt
+++ b/Documentation/devicetree/bindings/arm/freescale/fsl,imx7ulp-sim.txt
@ -0,0 +1,16 @@
+Freescale i.MX7ULP System Integration Module
+----------------------------------------------
+The system integration module (SIM) provides system control and chip configuration
+registers. In this module, chip revision information is located in JTAG ID register,
+and a set of registers have been made available in DGO domain for SW use, with the
+objective to maintain its value between system resets.
+
+Required properties:
+- compatible:	Should be "fsl,imx7ulp-sim".
+- reg:		Specifies base physical address and size of the register sets.
+
+Example:
+sim: sim@410a3000 {
+	compatible = "fsl,imx7ulp-sim", "syscon";
+	reg = <0x410a3000 0x1000>;
+};
--- a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
+++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
@ -70,7 +70,10 @@ Clock bindings based on SCU Message Protocol
 This binding uses the common clock binding[1].

 Required properties:
- compatible:		Should be "fsl,imx8qxp-clock".
+- compatible:		Should be one of:
+			  "fsl,imx8qm-clock"
+			  "fsl,imx8qxp-clock"
+			followed by "fsl,scu-clk"
 - #clock-cells:		Should be 1. Contains the Clock ID value.
 - clocks:		List of clock specifiers, must contain an entry for
 			each required entry in clock-names
@ -137,7 +140,7 @@ firmware {
 			  &lsio_mu1 1 3>;

 		clk: clk {
-			compatible = "fsl,imx8qxp-clk";
+			compatible = "fsl,imx8qxp-clk", "fsl,scu-clk";
 			#clock-cells = <1>;
 		};

--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@ -1,237 +0,0 @@
-Freescale i.MX Platforms Device Tree Bindings
-----------------------------------------------
-
-i.MX23 Evaluation Kit
-Required root node properties:
-    - compatible = "fsl,imx23-evk", "fsl,imx23";
-
-i.MX25 Product Development Kit
-Required root node properties:
-    - compatible = "fsl,imx25-pdk", "fsl,imx25";
-
-i.MX27 Product Development Kit
-Required root node properties:
-    - compatible = "fsl,imx27-pdk", "fsl,imx27";
-
-i.MX28 Evaluation Kit
-Required root node properties:
-    - compatible = "fsl,imx28-evk", "fsl,imx28";
-
-i.MX51 Babbage Board
-Required root node properties:
-    - compatible = "fsl,imx51-babbage", "fsl,imx51";
-
-i.MX53 Automotive Reference Design Board
-Required root node properties:
-    - compatible = "fsl,imx53-ard", "fsl,imx53";
-
-i.MX53 Evaluation Kit
-Required root node properties:
-    - compatible = "fsl,imx53-evk", "fsl,imx53";
-
-i.MX53 Quick Start Board
-Required root node properties:
-    - compatible = "fsl,imx53-qsb", "fsl,imx53";
-
-i.MX53 Smart Mobile Reference Design Board
-Required root node properties:
-    - compatible = "fsl,imx53-smd", "fsl,imx53";
-
-i.MX6 Quad Armadillo2 Board
-Required root node properties:
-    - compatible = "fsl,imx6q-arm2", "fsl,imx6q";
-
-i.MX6 Quad SABRE Lite Board
-Required root node properties:
-    - compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
-
-i.MX6 Quad SABRE Smart Device Board
-Required root node properties:
-    - compatible = "fsl,imx6q-sabresd", "fsl,imx6q";
-
-i.MX6 Quad SABRE Automotive Board
-Required root node properties:
-    - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q";
-
-i.MX6SLL EVK board
-Required root node properties:
-    - compatible = "fsl,imx6sll-evk", "fsl,imx6sll";
-
-i.MX6 Quad Plus SABRE Smart Device Board
-Required root node properties:
-    - compatible = "fsl,imx6qp-sabresd", "fsl,imx6qp";
-
-i.MX6 Quad Plus SABRE Automotive Board
-Required root node properties:
-    - compatible = "fsl,imx6qp-sabreauto", "fsl,imx6qp";
-
-i.MX6 DualLite SABRE Smart Device Board
-Required root node properties:
-    - compatible = "fsl,imx6dl-sabresd", "fsl,imx6dl";
-
-i.MX6 DualLite/Solo SABRE Automotive Board
-Required root node properties:
-    - compatible = "fsl,imx6dl-sabreauto", "fsl,imx6dl";
-
-i.MX6 SoloLite EVK Board
-Required root node properties:
-    - compatible = "fsl,imx6sl-evk", "fsl,imx6sl";
-
-i.MX6 UltraLite 14x14 EVK Board
-Required root node properties:
-    - compatible = "fsl,imx6ul-14x14-evk", "fsl,imx6ul";
-
-i.MX6 UltraLiteLite 14x14 EVK Board
-Required root node properties:
-    - compatible = "fsl,imx6ull-14x14-evk", "fsl,imx6ull";
-
-i.MX6 ULZ 14x14 EVK Board
-Required root node properties:
-    - compatible = "fsl,imx6ulz-14x14-evk", "fsl,imx6ull", "fsl,imx6ulz";
-
-i.MX6 SoloX SDB Board
-Required root node properties:
-    - compatible = "fsl,imx6sx-sdb", "fsl,imx6sx";
-
-i.MX6 SoloX Sabre Auto Board
-Required root node properties:
-    - compatible = "fsl,imx6sx-sabreauto", "fsl,imx6sx";
-
-i.MX7 SabreSD Board
-Required root node properties:
-    - compatible = "fsl,imx7d-sdb", "fsl,imx7d";
-
-i.MX7ULP Evaluation Kit
-Required root node properties:
-    - compatible = "fsl,imx7ulp-evk", "fsl,imx7ulp";
-
-Generic i.MX boards
-------------------
-
-No iomux setup is done for these boards, so this must have been configured
-by the bootloader for boards to work with the generic bindings.
-
-i.MX27 generic board
-Required root node properties:
-    - compatible = "fsl,imx27";
-
-i.MX51 generic board
-Required root node properties:
-    - compatible = "fsl,imx51";
-
-i.MX53 generic board
-Required root node properties:
-    - compatible = "fsl,imx53";
-
-i.MX6q generic board
-Required root node properties:
-    - compatible = "fsl,imx6q";
-
-i.MX7ULP generic board
-Required root node properties:
-    - compatible = "fsl,imx7ulp";
-
-Freescale Vybrid Platform Device Tree Bindings
----------------------------------------------
-
-For the Vybrid SoC familiy all variants with DDR controller are supported,
-which is the VF5xx and VF6xx series. Out of historical reasons, in most
-places the kernel uses vf610 to refer to the whole familiy.
-The compatible string "fsl,vf610m4" is used for the secondary Cortex-M4
-core support.
-
-Required root node compatible property (one of them):
-    - compatible = "fsl,vf500";
-    - compatible = "fsl,vf510";
-    - compatible = "fsl,vf600";
-    - compatible = "fsl,vf610";
-    - compatible = "fsl,vf610m4";
-
-Freescale LS1021A Platform Device Tree Bindings
------------------------------------------------
-
-Required root node compatible properties:
-  - compatible = "fsl,ls1021a";
-
-Freescale ARMv8 based Layerscape SoC family Device Tree Bindings
----------------------------------------------------------------
-
-LS1012A SoC
-Required root node properties:
-    - compatible = "fsl,ls1012a";
-
-LS1012A ARMv8 based RDB Board
-Required root node properties:
-    - compatible = "fsl,ls1012a-rdb", "fsl,ls1012a";
-
-LS1012A ARMv8 based FRDM Board
-Required root node properties:
-    - compatible = "fsl,ls1012a-frdm", "fsl,ls1012a";
-
-LS1012A ARMv8 based QDS Board
-Required root node properties:
-    - compatible = "fsl,ls1012a-qds", "fsl,ls1012a";
-
-LS1043A SoC
-Required root node properties:
-    - compatible = "fsl,ls1043a";
-
-LS1043A ARMv8 based RDB Board
-Required root node properties:
-    - compatible = "fsl,ls1043a-rdb", "fsl,ls1043a";
-
-LS1043A ARMv8 based QDS Board
-Required root node properties:
-    - compatible = "fsl,ls1043a-qds", "fsl,ls1043a";
-
-LS1046A SoC
-Required root node properties:
-    - compatible = "fsl,ls1046a";
-
-LS1046A ARMv8 based QDS Board
-Required root node properties:
-    - compatible = "fsl,ls1046a-qds", "fsl,ls1046a";
-
-LS1046A ARMv8 based RDB Board
-Required root node properties:
-    - compatible = "fsl,ls1046a-rdb", "fsl,ls1046a";
-
-LS1088A SoC
-Required root node properties:
-    - compatible = "fsl,ls1088a";
-
-LS1088A ARMv8 based QDS Board
-Required root node properties:
-    - compatible = "fsl,ls1088a-qds", "fsl,ls1088a";
-
-LS1088A ARMv8 based RDB Board
-Required root node properties:
-    - compatible = "fsl,ls1088a-rdb", "fsl,ls1088a";
-
-LS2080A SoC
-Required root node properties:
-    - compatible = "fsl,ls2080a";
-
-LS2080A ARMv8 based Simulator model
-Required root node properties:
-    - compatible = "fsl,ls2080a-simu", "fsl,ls2080a";
-
-LS2080A ARMv8 based QDS Board
-Required root node properties:
-    - compatible = "fsl,ls2080a-qds", "fsl,ls2080a";
-
-LS2080A ARMv8 based RDB Board
-Required root node properties:
-    - compatible = "fsl,ls2080a-rdb", "fsl,ls2080a";
-
-LS2088A SoC
-Required root node properties:
-    - compatible = "fsl,ls2088a";
-
-LS2088A ARMv8 based QDS Board
-Required root node properties:
-    - compatible = "fsl,ls2088a-qds", "fsl,ls2088a";
-
-LS2088A ARMv8 based RDB Board
-Required root node properties:
-    - compatible = "fsl,ls2088a-rdb", "fsl,ls2088a";
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@ -0,0 +1,232 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bindings/arm/fsl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX Platforms Device Tree Bindings
+
+maintainers:
+  - Shawn Guo <shawnguo@kernel.org>
+  - Li Yang <leoyang.li@nxp.com>
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+      - description: i.MX23 based Boards
+        items:
+          - enum:
+              - fsl,imx23-evk
+              - olimex,imx23-olinuxino
+          - const: fsl,imx23
+
+      - description: i.MX25 Product Development Kit
+        items:
+          - enum:
+              - fsl,imx25-pdk
+          - const: fsl,imx25
+
+      - description: i.MX27 Product Development Kit
+        items:
+          - enum:
+              - fsl,imx27-pdk
+          - const: fsl,imx27
+
+      - description: i.MX28 based Boards
+        items:
+          - enum:
+              - fsl,imx28-evk
+              - i2se,duckbill
+              - i2se,duckbill-2
+              - technologic,imx28-ts4600
+          - const: fsl,imx28
+      - description: i.MX28 Duckbill 2 based Boards
+        items:
+          - enum:
+              - i2se,duckbill-2-485
+              - i2se,duckbill-2-enocean
+              - i2se,duckbill-2-spi
+          - const: i2se,duckbill-2
+          - const: fsl,imx28
+
+      - description: i.MX51 Babbage Board
+        items:
+          - enum:
+              - armadeus,imx51-apf51
+              - fsl,imx51-babbage
+              - technologic,imx51-ts4800
+          - const: fsl,imx51
+
+      - description: i.MX53 based Boards
+        items:
+          - enum:
+              - bhf,cx9020
+              - fsl,imx53-ard
+              - fsl,imx53-evk
+              - fsl,imx53-qsb
+              - fsl,imx53-smd
+          - const: fsl,imx53
+
+      - description: i.MX6Q based Boards
+        items:
+          - enum:
+              - fsl,imx6q-arm2
+              - fsl,imx6q-sabreauto
+              - fsl,imx6q-sabrelite
+              - fsl,imx6q-sabresd
+              - technologic,imx6q-ts4900
+              - technologic,imx6q-ts7970
+          - const: fsl,imx6q
+
+      - description: i.MX6QP based Boards
+        items:
+          - enum:
+              - fsl,imx6qp-sabreauto      # i.MX6 Quad Plus SABRE Automotive Board
+              - fsl,imx6qp-sabresd        # i.MX6 Quad Plus SABRE Smart Device Board
+          - const: fsl,imx6qp
+
+      - description: i.MX6DL based Boards
+        items:
+          - enum:
+              - fsl,imx6dl-sabreauto      # i.MX6 DualLite/Solo SABRE Automotive Board
+              - fsl,imx6dl-sabresd        # i.MX6 DualLite SABRE Smart Device Board
+              - technologic,imx6dl-ts4900
+              - technologic,imx6dl-ts7970
+              - ysoft,imx6dl-yapp4-draco  # i.MX6 DualLite Y Soft IOTA Draco board
+              - ysoft,imx6dl-yapp4-hydra  # i.MX6 DualLite Y Soft IOTA Hydra board
+              - ysoft,imx6dl-yapp4-ursa   # i.MX6 Solo Y Soft IOTA Ursa board
+          - const: fsl,imx6dl
+
+      - description: i.MX6SL based Boards
+        items:
+          - enum:
+              - fsl,imx6sl-evk            # i.MX6 SoloLite EVK Board
+          - const: fsl,imx6sl
+
+      - description: i.MX6SLL based Boards
+        items:
+          - enum:
+              - fsl,imx6sll-evk
+          - const: fsl,imx6sll
+
+      - description: i.MX6SX based Boards
+        items:
+          - enum:
+              - fsl,imx6sx-sabreauto      # i.MX6 SoloX Sabre Auto Board
+              - fsl,imx6sx-sdb            # i.MX6 SoloX SDB Board
+          - const: fsl,imx6sx
+
+      - description: i.MX6UL based Boards
+        items:
+          - enum:
+              - fsl,imx6ul-14x14-evk      # i.MX6 UltraLite 14x14 EVK Board
+          - const: fsl,imx6ul
+
+      - description: i.MX6ULL based Boards
+        items:
+          - enum:
+              - fsl,imx6ull-14x14-evk     # i.MX6 UltraLiteLite 14x14 EVK Board
+          - const: fsl,imx6ull
+
+      - description: i.MX6ULZ based Boards
+        items:
+          - enum:
+              - fsl,imx6ulz-14x14-evk     # i.MX6 ULZ 14x14 EVK Board
+          - const: fsl,imx6ull # This seems odd. Should be last?
+          - const: fsl,imx6ulz
+
+      - description: i.MX7D based Boards
+        items:
+          - enum:
+              - fsl,imx7d-sdb             # i.MX7 SabreSD Board
+          - const: fsl,imx7d
+
+      - description:
+          Compulab SBC-iMX7 is a single board computer based on the
+          Freescale i.MX7 system-on-chip. SBC-iMX7 is implemented with
+          the CL-SOM-iMX7 System-on-Module providing most of the functions,
+          and SB-SOM-iMX7 carrier board providing additional peripheral
+          functions and connectors.
+        items:
+          - const: compulab,sbc-imx7
+          - const: compulab,cl-som-imx7
+          - const: fsl,imx7d
+
+      - description: i.MX8QXP based Boards
+        items:
+          - enum:
+              - fsl,imx8qxp-mek           # i.MX8QXP MEK Board
+          - const: fsl,imx8qxp
+
+      - description:
+          Freescale Vybrid Platform Device Tree Bindings
+
+          For the Vybrid SoC familiy all variants with DDR controller are supported,
+          which is the VF5xx and VF6xx series. Out of historical reasons, in most
+          places the kernel uses vf610 to refer to the whole familiy.
+          The compatible string "fsl,vf610m4" is used for the secondary Cortex-M4
+          core support.
+        items:
+          - enum:
+              - fsl,vf500
+              - fsl,vf510
+              - fsl,vf600
+              - fsl,vf610
+              - fsl,vf610m4
+
+      - description: LS1012A based Boards
+        items:
+          - enum:
+              - ebs-systart,oxalis
+              - fsl,ls1012a-rdb
+              - fsl,ls1012a-frdm
+              - fsl,ls1012a-qds
+          - const: fsl,ls1012a
+
+      - description: LS1021A based Boards
+        items:
+          - enum:
+              - fsl,ls1021a-moxa-uc-8410a
+              - fsl,ls1021a-qds
+              - fsl,ls1021a-twr
+          - const: fsl,ls1021a
+
+      - description: LS1043A based Boards
+        items:
+          - enum:
+              - fsl,ls1043a-rdb
+              - fsl,ls1043a-qds
+          - const: fsl,ls1043a
+
+      - description: LS1046A based Boards
+        items:
+          - enum:
+              - fsl,ls1046a-qds
+              - fsl,ls1046a-rdb
+          - const: fsl,ls1046a
+
+      - description: LS1088A based Boards
+        items:
+          - enum:
+              - fsl,ls1088a-qds
+              - fsl,ls1088a-rdb
+          - const: fsl,ls1088a
+
+      - description: LS2080A based Boards
+        items:
+          - enum:
+              - fsl,ls2080a-simu
+              - fsl,ls2080a-qds
+              - fsl,ls2080a-rdb
+          - const: fsl,ls2080a
+
+      - description: LS2088A based Boards
+        items:
+          - enum:
+              - fsl,ls2088a-qds
+              - fsl,ls2088a-rdb
+          - const: fsl,ls2088a
+
+...
--- a/Documentation/devicetree/bindings/arm/i2se.txt
+++ b/Documentation/devicetree/bindings/arm/i2se.txt
@ -1,22 +0,0 @@
-I2SE Device Tree Bindings
-------------------------
-
-Duckbill Board
-Required root node properties:
-    - compatible = "i2se,duckbill", "fsl,imx28";
-
-Duckbill 2 Board
-Required root node properties:
-    - compatible = "i2se,duckbill-2", "fsl,imx28";
-
-Duckbill 2 485 Board
-Required root node properties:
-    - compatible = "i2se,duckbill-2-485", "i2se,duckbill-2", "fsl,imx28";
-
-Duckbill 2 EnOcean Board
-Required root node properties:
-    - compatible = "i2se,duckbill-2-enocean", "i2se,duckbill-2", "fsl,imx28";
-
-Duckbill 2 SPI Board
-Required root node properties:
-    - compatible = "i2se,duckbill-2-spi", "i2se,duckbill-2", "fsl,imx28";
--- a/Documentation/devicetree/bindings/arm/mediatek.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek.txt
@ -15,11 +15,12 @@ compatible: Must contain one of
   "mediatek,mt6795"
   "mediatek,mt6797"
   "mediatek,mt7622"
-   "mediatek,mt7623" which is referred to MT7623N SoC
-   "mediatek,mt7623a"
+   "mediatek,mt7623"
+   "mediatek,mt7629"
   "mediatek,mt8127"
   "mediatek,mt8135"
   "mediatek,mt8173"
+   "mediatek,mt8183"


 Supported boards:
@ -57,6 +58,9 @@ Supported boards:
 - Reference board variant 1 for MT7622:
    Required root node properties:
      - compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622";
+- Bananapi BPI-R64 for MT7622:
+    Required root node properties:
+      - compatible = "bananapi,bpi-r64", "mediatek,mt7622";
 - Reference board for MT7623a with eMMC:
    Required root node properties:
      - compatible = "mediatek,mt7623a-rfb-emmc", "mediatek,mt7623";
@ -68,6 +72,9 @@ Supported boards:
      - compatible = "mediatek,mt7623n-rfb-emmc", "mediatek,mt7623";
 - Bananapi BPI-R2 board:
      - compatible = "bananapi,bpi-r2", "mediatek,mt7623";
+- Reference board for MT7629:
+    Required root node properties:
+      - compatible = "mediatek,mt7629-rfb", "mediatek,mt7629";
 - MTK mt8127 tablet moose EVB:
    Required root node properties:
      - compatible = "mediatek,mt8127-moose", "mediatek,mt8127";
@ -77,3 +84,6 @@ Supported boards:
 - MTK mt8173 tablet EVB:
    Required root node properties:
      - compatible = "mediatek,mt8173-evb", "mediatek,mt8173";
+- Evaluation board for MT8183:
+    Required root node properties:
+      - compatible = "mediatek,mt8183-evb", "mediatek,mt8183";
--- a/Documentation/devicetree/bindings/arm/olimex.txt
+++ b/Documentation/devicetree/bindings/arm/olimex.txt
@ -1,10 +0,0 @@
-Olimex Device Tree Bindings
---------------------------
-
-SAM9-L9260 Board
-Required root node properties:
-    - compatible = "olimex,sam9-l9260", "atmel,at91sam9260";
-
-i.MX23 Olinuxino Low Cost Board
-Required root node properties:
-    - compatible = "olimex,imx23-olinuxino", "fsl,imx23";
--- a/Documentation/devicetree/bindings/arm/renesas.yaml
+++ b/Documentation/devicetree/bindings/arm/renesas.yaml
@ -0,0 +1,238 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/arm/shmobile.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas SH-Mobile, R-Mobile, and R-Car Platform Device Tree Bindings
+
+maintainers:
+  - Geert Uytterhoeven <geert+renesas@glider.be>
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+      - description: Emma Mobile EV2
+        items:
+          - enum:
+              - renesas,kzm9d # Kyoto Microcomputer Co. KZM-A9-Dual
+          - const: renesas,emev2
+
+      - description: RZ/A1H (R7S72100)
+        items:
+          - enum:
+              - renesas,genmai # Genmai (RTK772100BC00000BR)
+              - renesas,gr-peach # GR-Peach (X28A-M01-E/F)
+              - renesas,rskrza1 # RSKRZA1 (YR0K77210C000BE)
+          - const: renesas,r7s72100
+
+      - description: RZ/A2 (R7S9210)
+        items:
+          - enum:
+              - renesas,rza2mevb # RZ/A2M Eval Board (RTK7921053S00000BE)
+          - const: renesas,r7s9210
+
+      - description: SH-Mobile AG5 (R8A73A00/SH73A0)
+        items:
+          - enum:
+              - renesas,kzm9g # Kyoto Microcomputer Co. KZM-A9-GT
+          - const: renesas,sh73a0
+
+      - description: R-Mobile APE6 (R8A73A40)
+        items:
+          - enum:
+              - renesas,ape6evm
+          - const: renesas,r8a73a4
+
+      - description: R-Mobile A1 (R8A77400)
+        items:
+          - enum:
+              - renesas,armadillo800eva # Atmark Techno Armadillo-800 EVA
+          - const: renesas,r8a7740
+
+      - description: RZ/G1H (R8A77420)
+        items:
+          - const: renesas,r8a7742
+
+      - description: RZ/G1M (R8A77430)
+        items:
+          - enum:
+              # iWave Systems RZ/G1M Qseven Development Platform (iW-RainboW-G20D-Qseven)
+              - iwave,g20d
+          - const: iwave,g20m
+          - const: renesas,r8a7743
+
+      - items:
+          - enum:
+              # iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
+              - iwave,g20m
+              - renesas,sk-rzg1m # SK-RZG1M (YR8A77430S000BE)
+          - const: renesas,r8a7743
+
+      - description: RZ/G1N (R8A77440)
+        items:
+          - enum:
+              # iWave Systems RZ/G1N Qseven Development Platform (iW-RainboW-G20D-Qseven)
+              - iwave,g20d
+          - const: iwave,g20m
+          - const: renesas,r8a7744
+
+      - items:
+          - enum:
+              # iWave Systems RZ/G1N Qseven System On Module (iW-RainboW-G20M-Qseven)
+              - iwave,g20m
+          - const: renesas,r8a7744
+
+      - description: RZ/G1E (R8A77450)
+        items:
+          - enum:
+              - iwave,g22m # iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM)
+              - renesas,sk-rzg1e # SK-RZG1E (YR8A77450S000BE)
+          - const: renesas,r8a7745
+
+      - description: iWave Systems RZ/G1E SODIMM SOM Development Platform (iW-RainboW-G22D)
+        items:
+          - const: iwave,g22d
+          - const: iwave,g22m
+          - const: renesas,r8a7745
+
+      - description: RZ/G1C (R8A77470)
+        items:
+          - enum:
+              - iwave,g23s #iWave Systems RZ/G1C Single Board Computer (iW-RainboW-G23S)
+          - const: renesas,r8a77470
+
+      - description: RZ/G2M (R8A774A1)
+        items:
+          - const: renesas,r8a774a1
+
+      - description: RZ/G2E (R8A774C0)
+        items:
+          - enum:
+              - si-linux,cat874 # Silicon Linux RZ/G2E 96board platform (CAT874)
+          - const: renesas,r8a774c0
+
+      - items:
+          - enum:
+              - si-linux,cat875 # Silicon Linux sub board for CAT874 (CAT875)
+          - const: si-linux,cat874
+          - const: renesas,r8a774c0
+
+      - description: R-Car M1A (R8A77781)
+        items:
+          - enum:
+              - renesas,bockw
+          - const: renesas,r8a7778
+
+      - description: R-Car H1 (R8A77790)
+        items:
+          - enum:
+              - renesas,marzen # Marzen (R0P7779A00010S)
+          - const: renesas,r8a7779
+
+      - description: R-Car H2 (R8A77900)
+        items:
+          - enum:
+              - renesas,lager # Lager (RTP0RC7790SEB00010S)
+              - renesas,stout # Stout (ADAS Starterkit, Y-R-CAR-ADAS-SKH2-BOARD)
+          - const: renesas,r8a7790
+
+      - description: R-Car M2-W (R8A77910)
+        items:
+          - enum:
+              - renesas,henninger
+              - renesas,koelsch # Koelsch (RTP0RC7791SEB00010S)
+              - renesas,porter # Porter (M2-LCDP)
+          - const: renesas,r8a7791
+
+      - description: R-Car V2H (R8A77920)
+        items:
+          - enum:
+              - renesas,blanche # Blanche (RTP0RC7792SEB00010S)
+              - renesas,wheat # Wheat (RTP0RC7792ASKB0000JE)
+          - const: renesas,r8a7792
+
+      - description: R-Car M2-N (R8A77930)
+        items:
+          - enum:
+              - renesas,gose # Gose (RTP0RC7793SEB00010S)
+          - const: renesas,r8a7793
+
+      - description: R-Car E2 (R8A77940)
+        items:
+          - enum:
+              - renesas,alt # Alt (RTP0RC7794SEB00010S)
+              - renesas,silk # SILK (RTP0RC7794LCB00011S)
+          - const: renesas,r8a7794
+
+      - description: R-Car H3 (R8A77950)
+        items:
+          - enum:
+                # H3ULCB (R-Car Starter Kit Premier, RTP0RC7795SKBX0010SA00 (H3 ES1.1))
+                # H3ULCB (R-Car Starter Kit Premier, RTP0RC77951SKBX010SA00 (H3 ES2.0))
+              - renesas,h3ulcb
+              - renesas,salvator-x # Salvator-X (RTP0RC7795SIPB0010S)
+              - renesas,salvator-xs # Salvator-XS (Salvator-X 2nd version, RTP0RC7795SIPB0012S)
+          - const: renesas,r8a7795
+
+      - description: R-Car M3-W (R8A77960)
+        items:
+          - enum:
+              - renesas,m3ulcb # M3ULCB (R-Car Starter Kit Pro, RTP0RC7796SKBX0010SA09 (M3 ES1.0))
+              - renesas,salvator-x # Salvator-X (RTP0RC7796SIPB0011S)
+              - renesas,salvator-xs # Salvator-XS (Salvator-X 2nd version, RTP0RC7796SIPB0012S)
+          - const: renesas,r8a7796
+
+      - description: Kingfisher (SBEV-RCAR-KF-M03)
+        items:
+          - const: shimafuji,kingfisher
+          - enum:
+              - renesas,h3ulcb
+              - renesas,m3ulcb
+          - enum:
+              - renesas,r8a7795
+              - renesas,r8a7796
+
+      - description: R-Car M3-N (R8A77965)
+        items:
+          - enum:
+              - renesas,m3nulcb # M3NULCB (R-Car Starter Kit Pro, RTP0RC77965SKBX010SA00 (M3-N ES1.1))
+              - renesas,salvator-x # Salvator-X (RTP0RC7796SIPB0011S (M3-N))
+              - renesas,salvator-xs # Salvator-XS (Salvator-X 2nd version, RTP0RC77965SIPB012S)
+          - const: renesas,r8a77965
+
+      - description: R-Car V3M (R8A77970)
+        items:
+          - enum:
+              - renesas,eagle # Eagle (RTP0RC77970SEB0010S)
+              - renesas,v3msk # V3MSK (Y-ASK-RCAR-V3M-WS10)
+          - const: renesas,r8a77970
+
+      - description: R-Car V3H (R8A77980)
+        items:
+          - enum:
+              - renesas,condor # Condor (RTP0RC77980SEB0010SS/RTP0RC77980SEB0010SA01)
+              - renesas,v3hsk # V3HSK (Y-ASK-RCAR-V3H-WS10)
+          - const: renesas,r8a77980
+
+      - description: R-Car E3 (R8A77990)
+        items:
+          - enum:
+              - renesas,ebisu # Ebisu (RTP0RC77990SEB0010S)
+          - const: renesas,r8a77990
+
+      - description: R-Car D3 (R8A77995)
+        items:
+          - enum:
+              - renesas,draak # Draak (RTP0RC77995SEB0010S)
+          - const: renesas,r8a77995
+
+      - description: RZ/N1D (R9A06G032)
+        items:
+          - enum:
+              - renesas,rzn1d400-db # RZN1D-DB (RZ/N1D Demo Board for the RZ/N1D 400 pins package)
+          - const: renesas,r9a06g032
+
+...
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@ -60,6 +60,11 @@ properties:
          - const: chipspark,rayeager-px2
          - const: rockchip,rk3066a

+      - description: Elgin RV1108 R1
+        items:
+          - const: elgin,rv1108-r1
+          - const: rockchip,rv1108
+
      - description: Firefly Firefly-RK3288
        items:
          - enum:
@ -87,6 +92,13 @@ properties:
          - const: firefly,roc-rk3399-pc
          - const: rockchip,rk3399

+      - description: FriendlyElec NanoPi4 series boards
+        items:
+          - enum:
+              - friendlyarm,nanopc-t4
+              - friendlyarm,nanopi-m4
+          - const: rockchip,rk3399
+
      - description: GeekBuying GeekBox
        items:
          - const: geekbuying,geekbox
@ -317,6 +329,11 @@ properties:
          - const: radxa,rock
          - const: rockchip,rk3188

+      - description: Radxa ROCK Pi 4
+        items:
+          - const: radxa,rockpi4
+          - const: rockchip,rk3399
+
      - description: Radxa Rock2 Square
        items:
          - const: radxa,rock2-square
--- a/Documentation/devicetree/bindings/arm/shmobile.txt
+++ b/Documentation/devicetree/bindings/arm/shmobile.txt
@ -1,155 +0,0 @@
-Renesas SH-Mobile, R-Mobile, and R-Car Platform Device Tree Bindings
--------------------------------------------------------------------
-
-SoCs:
-
-  - Emma Mobile EV2
-    compatible = "renesas,emev2"
-  - RZ/A1H (R7S72100)
-    compatible = "renesas,r7s72100"
-  - RZ/A2 (R7S9210)
-    compatible = "renesas,r7s9210"
-  - SH-Mobile AG5 (R8A73A00/SH73A0)
-    compatible = "renesas,sh73a0"
-  - R-Mobile APE6 (R8A73A40)
-    compatible = "renesas,r8a73a4"
-  - R-Mobile A1 (R8A77400)
-    compatible = "renesas,r8a7740"
-  - RZ/G1H (R8A77420)
-    compatible = "renesas,r8a7742"
-  - RZ/G1M (R8A77430)
-    compatible = "renesas,r8a7743"
-  - RZ/G1N (R8A77440)
-    compatible = "renesas,r8a7744"
-  - RZ/G1E (R8A77450)
-    compatible = "renesas,r8a7745"
-  - RZ/G1C (R8A77470)
-    compatible = "renesas,r8a77470"
-  - RZ/G2M (R8A774A1)
-    compatible = "renesas,r8a774a1"
-  - RZ/G2E (R8A774C0)
-    compatible = "renesas,r8a774c0"
-  - R-Car M1A (R8A77781)
-    compatible = "renesas,r8a7778"
-  - R-Car H1 (R8A77790)
-    compatible = "renesas,r8a7779"
-  - R-Car H2 (R8A77900)
-    compatible = "renesas,r8a7790"
-  - R-Car M2-W (R8A77910)
-    compatible = "renesas,r8a7791"
-  - R-Car V2H (R8A77920)
-    compatible = "renesas,r8a7792"
-  - R-Car M2-N (R8A77930)
-    compatible = "renesas,r8a7793"
-  - R-Car E2 (R8A77940)
-    compatible = "renesas,r8a7794"
-  - R-Car H3 (R8A77950)
-    compatible = "renesas,r8a7795"
-  - R-Car M3-W (R8A77960)
-    compatible = "renesas,r8a7796"
-  - R-Car M3-N (R8A77965)
-    compatible = "renesas,r8a77965"
-  - R-Car V3M (R8A77970)
-    compatible = "renesas,r8a77970"
-  - R-Car V3H (R8A77980)
-    compatible = "renesas,r8a77980"
-  - R-Car E3 (R8A77990)
-    compatible = "renesas,r8a77990"
-  - R-Car D3 (R8A77995)
-    compatible = "renesas,r8a77995"
-  - RZ/N1D (R9A06G032)
-    compatible = "renesas,r9a06g032"
-
-Boards:
-
-  - Alt (RTP0RC7794SEB00010S)
-    compatible = "renesas,alt", "renesas,r8a7794"
-  - APE6-EVM
-    compatible = "renesas,ape6evm", "renesas,r8a73a4"
-  - Atmark Techno Armadillo-800 EVA
-    compatible = "renesas,armadillo800eva", "renesas,r8a7740"
-  - Blanche (RTP0RC7792SEB00010S)
-    compatible = "renesas,blanche", "renesas,r8a7792"
-  - BOCK-W
-    compatible = "renesas,bockw", "renesas,r8a7778"
-  - Condor (RTP0RC77980SEB0010SS/RTP0RC77980SEB0010SA01)
-    compatible = "renesas,condor", "renesas,r8a77980"
-  - Draak (RTP0RC77995SEB0010S)
-    compatible = "renesas,draak", "renesas,r8a77995"
-  - Eagle (RTP0RC77970SEB0010S)
-    compatible = "renesas,eagle", "renesas,r8a77970"
-  - Ebisu (RTP0RC77990SEB0010S)
-    compatible = "renesas,ebisu", "renesas,r8a77990"
-  - Genmai (RTK772100BC00000BR)
-    compatible = "renesas,genmai", "renesas,r7s72100"
-  - GR-Peach (X28A-M01-E/F)
-    compatible = "renesas,gr-peach", "renesas,r7s72100"
-  - Gose (RTP0RC7793SEB00010S)
-    compatible = "renesas,gose", "renesas,r8a7793"
-  - H3ULCB (R-Car Starter Kit Premier, RTP0RC7795SKBX0010SA00 (H3 ES1.1))
-    H3ULCB (R-Car Starter Kit Premier, RTP0RC77951SKBX010SA00 (H3 ES2.0))
-    compatible = "renesas,h3ulcb", "renesas,r8a7795"
-  - Henninger
-    compatible = "renesas,henninger", "renesas,r8a7791"
-  - iWave Systems RZ/G1C Single Board Computer (iW-RainboW-G23S)
-    compatible = "iwave,g23s", "renesas,r8a77470"
-  - iWave Systems RZ/G1E SODIMM SOM Development Platform (iW-RainboW-G22D)
-    compatible = "iwave,g22d", "iwave,g22m", "renesas,r8a7745"
-  - iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM)
-    compatible = "iwave,g22m", "renesas,r8a7745"
-  - iWave Systems RZ/G1M Qseven Development Platform (iW-RainboW-G20D-Qseven)
-    compatible = "iwave,g20d", "iwave,g20m", "renesas,r8a7743"
-  - iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
-    compatible = "iwave,g20m", "renesas,r8a7743"
-  - iWave Systems RZ/G1N Qseven Development Platform (iW-RainboW-G20D-Qseven)
-    compatible = "iwave,g20d", "iwave,g20m", "renesas,r8a7744"
-  - iWave Systems RZ/G1N Qseven System On Module (iW-RainboW-G20M-Qseven)
-    compatible = "iwave,g20m", "renesas,r8a7744"
-  - Kingfisher (SBEV-RCAR-KF-M03)
-    compatible = "shimafuji,kingfisher"
-  - Koelsch (RTP0RC7791SEB00010S)
-    compatible = "renesas,koelsch", "renesas,r8a7791"
-  - Kyoto Microcomputer Co. KZM-A9-Dual
-    compatible = "renesas,kzm9d", "renesas,emev2"
-  - Kyoto Microcomputer Co. KZM-A9-GT
-    compatible = "renesas,kzm9g", "renesas,sh73a0"
-  - Lager (RTP0RC7790SEB00010S)
-    compatible = "renesas,lager", "renesas,r8a7790"
-  - M3ULCB (R-Car Starter Kit Pro, RTP0RC7796SKBX0010SA09 (M3 ES1.0))
-    compatible = "renesas,m3ulcb", "renesas,r8a7796"
-  - M3NULCB (R-Car Starter Kit Pro, RTP0RC77965SKBX010SA00 (M3-N ES1.1))
-    compatible = "renesas,m3nulcb", "renesas,r8a77965"
-  - Marzen (R0P7779A00010S)
-    compatible = "renesas,marzen", "renesas,r8a7779"
-  - Porter (M2-LCDP)
-    compatible = "renesas,porter", "renesas,r8a7791"
-  - RSKRZA1 (YR0K77210C000BE)
-    compatible = "renesas,rskrza1", "renesas,r7s72100"
-  - RZN1D-DB (RZ/N1D Demo Board for the RZ/N1D 400 pins package)
-    compatible = "renesas,rzn1d400-db", "renesas,r9a06g032"
-  - Salvator-X (RTP0RC7795SIPB0010S)
-    compatible = "renesas,salvator-x", "renesas,r8a7795"
-  - Salvator-X (RTP0RC7796SIPB0011S)
-    compatible = "renesas,salvator-x", "renesas,r8a7796"
-  - Salvator-X (RTP0RC7796SIPB0011S (M3-N))
-    compatible = "renesas,salvator-x", "renesas,r8a77965"
-  - Salvator-XS (Salvator-X 2nd version, RTP0RC7795SIPB0012S)
-    compatible = "renesas,salvator-xs", "renesas,r8a7795"
-  - Salvator-XS (Salvator-X 2nd version, RTP0RC7796SIPB0012S)
-    compatible = "renesas,salvator-xs", "renesas,r8a7796"
-  - Salvator-XS (Salvator-X 2nd version, RTP0RC77965SIPB012S)
-    compatible = "renesas,salvator-xs", "renesas,r8a77965"
-  - SILK (RTP0RC7794LCB00011S)
-    compatible = "renesas,silk", "renesas,r8a7794"
-  - SK-RZG1E (YR8A77450S000BE)
-    compatible = "renesas,sk-rzg1e", "renesas,r8a7745"
-  - SK-RZG1M (YR8A77430S000BE)
-    compatible = "renesas,sk-rzg1m", "renesas,r8a7743"
-  - Stout (ADAS Starterkit, Y-R-CAR-ADAS-SKH2-BOARD)
-    compatible = "renesas,stout", "renesas,r8a7790"
-  - V3HSK (Y-ASK-RCAR-V3H-WS10)
-    compatible = "renesas,v3hsk", "renesas,r8a77980"
-  - V3MSK (Y-ASK-RCAR-V3M-WS10)
-    compatible = "renesas,v3msk", "renesas,r8a77970"
-  - Wheat (RTP0RC7792ASKB0000JE)
-    compatible = "renesas,wheat", "renesas,r8a7792"
--- a/Documentation/devicetree/bindings/arm/technologic.txt
+++ b/Documentation/devicetree/bindings/arm/technologic.txt
@ -1,23 +0,0 @@
-Technologic Systems Platforms Device Tree Bindings
--------------------------------------------------
-
-TS-4600 is a System-on-Module based on the Freescale i.MX28 System-on-Chip.
-It can be mounted on a carrier board providing additional peripheral connectors.
-Required root node properties:
-	- compatible = "technologic,imx28-ts4600", "fsl,imx28"
-
-TS-4800 board
-Required root node properties:
-	- compatible = "technologic,imx51-ts4800", "fsl,imx51";
-
-TS-4900 is a System-on-Module based on the Freescale i.MX6 System-on-Chip.
-It can be mounted on a carrier board providing additional peripheral connectors.
-Required root node properties:
-	- compatible = "technologic,imx6dl-ts4900", "fsl,imx6dl"
-	- compatible = "technologic,imx6q-ts4900", "fsl,imx6q"
-
-TS-7970 is a System-on-Module based on the Freescale i.MX6 System-on-Chip.
-It can be mounted on a carrier board providing additional peripheral connectors.
-Required root node properties:
-	- compatible = "technologic,imx6dl-ts7970", "fsl,imx6dl"
-	- compatible = "technologic,imx6q-ts7970", "fsl,imx6q"
--- a/Documentation/devicetree/bindings/arm/tegra.yaml
+++ b/Documentation/devicetree/bindings/arm/tegra.yaml
@ -87,9 +87,11 @@ properties:
          - const: nvidia,tegra124
      - items:
          - enum:
+              - nvidia,darcy
              - nvidia,p2371-0000
              - nvidia,p2371-2180
              - nvidia,p2571
+              - nvidia,p2894-0050-a08
          - const: nvidia,tegra210
      - items:
          - enum:
--- a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
+++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
@ -8,10 +8,11 @@ the fast CPU cluster. It consists of a free-running voltage controlled
 oscillator connected to the CPU voltage rail (VDD_CPU), and a closed loop
 control module that will automatically adjust the VDD_CPU voltage by
 communicating with an off-chip PMIC either via an I2C bus or via PWM signals.
-Currently only the I2C mode is supported by these bindings.

 Required properties:
- compatible : should be "nvidia,tegra124-dfll"
+- compatible : should be one of:
+  - "nvidia,tegra124-dfll": for Tegra124
+  - "nvidia,tegra210-dfll": for Tegra210
 - reg : Defines the following set of registers, in the order listed:
        - registers for the DFLL control logic.
        - registers for the I2C output logic.
@ -45,10 +46,31 @@ Required properties for the control loop parameters:
 Optional properties for the control loop parameters:
 - nvidia,cg-scale: Boolean value, see the field DFLL_PARAMS_CG_SCALE in the TRM.

+Optional properties for mode selection:
+- nvidia,pwm-to-pmic: Use PWM to control regulator rather then I2C.
+
 Required properties for I2C mode:
 - nvidia,i2c-fs-rate: I2C transfer rate, if using full speed mode.

-Example:
+Required properties for PWM mode:
+- nvidia,pwm-period-nanoseconds: period of PWM square wave in nanoseconds.
+- nvidia,pwm-tristate-microvolts: Regulator voltage in micro volts when PWM
+  control is disabled and the PWM output is tristated. Note that this voltage is
+  configured in hardware, typically via a resistor divider.
+- nvidia,pwm-min-microvolts: Regulator voltage in micro volts when PWM control
+  is enabled and PWM output is low. Hence, this is the minimum output voltage
+  that the regulator supports when PWM control is enabled.
+- nvidia,pwm-voltage-step-microvolts: Voltage increase in micro volts
+  corresponding to a 1/33th increase in duty cycle. Eg the voltage for 2/33th
+  duty cycle would be: nvidia,pwm-min-microvolts +
+  nvidia,pwm-voltage-step-microvolts * 2.
+- pinctrl-0: I/O pad configuration when PWM control is enabled.
+- pinctrl-1: I/O pad configuration when PWM control is disabled.
+- pinctrl-names: must include the following entries:
+  - dvfs_pwm_enable: I/O pad configuration when PWM control is enabled.
+  - dvfs_pwm_disable: I/O pad configuration when PWM control is disabled.
+
+Example for I2C:

 clock@70110000 {
        compatible = "nvidia,tegra124-dfll";
@ -76,3 +98,58 @@ clock@70110000 {

        nvidia,i2c-fs-rate = <400000>;
 };
+
+Example for PWM:
+
+clock@70110000 {
+	compatible = "nvidia,tegra124-dfll";
+	reg = <0 0x70110000 0 0x100>, /* DFLL control */
+	      <0 0x70110000 0 0x100>, /* I2C output control */
+	      <0 0x70110100 0 0x100>, /* Integrated I2C controller */
+	      <0 0x70110200 0 0x100>; /* Look-up table RAM */
+	interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&tegra_car TEGRA210_CLK_DFLL_SOC>,
+	         <&tegra_car TEGRA210_CLK_DFLL_REF>,
+		 <&tegra_car TEGRA124_CLK_I2C5>;;
+	clock-names = "soc", "ref", "i2c";
+	resets = <&tegra_car TEGRA124_RST_DFLL_DVCO>;
+	reset-names = "dvco";
+	#clock-cells = <0>;
+	clock-output-names = "dfllCPU_out";
+
+	nvidia,sample-rate = <25000>;
+	nvidia,droop-ctrl = <0x00000f00>;
+	nvidia,force-mode = <1>;
+	nvidia,cf = <6>;
+	nvidia,ci = <0>;
+	nvidia,cg = <2>;
+
+	nvidia,pwm-min-microvolts = <708000>; /* 708mV */
+	nvidia,pwm-period-nanoseconds = <2500>; /* 2.5us */
+	nvidia,pwm-to-pmic;
+	nvidia,pwm-tristate-microvolts = <1000000>;
+	nvidia,pwm-voltage-step-microvolts = <19200>; /* 19.2mV */
+
+	pinctrl-names = "dvfs_pwm_enable", "dvfs_pwm_disable";
+	pinctrl-0 = <&dvfs_pwm_active_state>;
+	pinctrl-1 = <&dvfs_pwm_inactive_state>;
+};
+
+/* pinmux nodes added for completeness. Binding doc can be found in:
+ * Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt
+ */
+
+pinmux: pinmux@700008d4 {
+	dvfs_pwm_active_state: dvfs_pwm_active {
+		dvfs_pwm_pbb1 {
+			nvidia,pins = "dvfs_pwm_pbb1";
+			nvidia,tristate = <TEGRA_PIN_DISABLE>;
+		};
+	};
+	dvfs_pwm_inactive_state: dvfs_pwm_inactive {
+		dvfs_pwm_pbb1 {
+			nvidia,pins = "dvfs_pwm_pbb1";
+			nvidia,tristate = <TEGRA_PIN_ENABLE>;
+		};
+	};
+};
--- a/Documentation/devicetree/bindings/cpufreq/nvidia,tegra124-cpufreq.txt
+++ b/Documentation/devicetree/bindings/cpufreq/nvidia,tegra124-cpufreq.txt
@ -9,11 +9,9 @@ Required properties:
  See ../clocks/clock-bindings.txt for details.
 - clock-names: Must include the following entries:
  - cpu_g: Clock mux for the fast CPU cluster.
-  - cpu_lp: Clock mux for the low-power CPU cluster.
  - pll_x: Fast PLL clocksource.
  - pll_p: Auxiliary PLL used during fast PLL rate changes.
  - dfll: Fast DFLL clocksource that also automatically scales CPU voltage.
- vdd-cpu-supply: Regulator for CPU voltage

 Optional properties:
 - clock-latency: Specify the possible maximum transition latency for clock,
@ -31,13 +29,11 @@ cpus {
 		reg = <0>;

 		clocks = <&tegra_car TEGRA124_CLK_CCLK_G>,
-			 <&tegra_car TEGRA124_CLK_CCLK_LP>,
 			 <&tegra_car TEGRA124_CLK_PLL_X>,
 			 <&tegra_car TEGRA124_CLK_PLL_P>,
 			 <&dfll>;
-		clock-names = "cpu_g", "cpu_lp", "pll_x", "pll_p", "dfll";
+		clock-names = "cpu_g", "pll_x", "pll_p", "dfll";
 		clock-latency = <300000>;
-		vdd-cpu-supply: <&vdd_cpu>;
 	};

 	<...>
--- a/Documentation/devicetree/bindings/display/amlogic,simple-framebuffer.txt
+++ b/Documentation/devicetree/bindings/display/amlogic,simple-framebuffer.txt
@ -0,0 +1,33 @@
+Meson specific Simple Framebuffer bindings
+
+This binding documents meson specific extensions to the simple-framebuffer
+bindings. The meson simplefb u-boot code relies on the devicetree containing
+pre-populated simplefb nodes.
+
+These extensions are intended so that u-boot can select the right node based
+on which pipeline is being used. As such they are solely intended for
+firmware / bootloader use, and the OS should ignore them.
+
+Required properties:
+- compatible: "amlogic,simple-framebuffer", "simple-framebuffer"
+- amlogic,pipeline, one of:
+  "vpu-cvbs"
+  "vpu-hdmi"
+
+Example:
+
+chosen {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+
+	simplefb_hdmi: framebuffer-hdmi {
+		compatible = "amlogic,simple-framebuffer",
+			     "simple-framebuffer";
+		amlogic,pipeline = "vpu-hdmi";
+		clocks = <&clkc CLKID_HDMI_PCLK>,
+			 <&clkc CLKID_CLK81>,
+			 <&clkc CLKID_GCLK_VENCI_INT0>;
+		power-domains = <&pwrc_vpu>;
+	};
+};
--- a/Documentation/devicetree/bindings/firmware/nvidia,tegra186-bpmp.txt
+++ b/Documentation/devicetree/bindings/firmware/nvidia,tegra186-bpmp.txt
@ -8,7 +8,6 @@ which can create the interprocessor communication (IPC) between the CPU
 and BPMP.

 Required properties:
- name : Should be bpmp
 - compatible
    Array of strings
    One of:
--- a/Documentation/devicetree/bindings/firmware/nvidia,tegra210-bpmp.txt
+++ b/Documentation/devicetree/bindings/firmware/nvidia,tegra210-bpmp.txt
@ -0,0 +1,35 @@
+NVIDIA Tegra210 Boot and Power Management Processor (BPMP)
+
+The Boot and Power Management Processor (BPMP) is a co-processor found
+in Tegra210 SoC. It is designed to handle the early stages of the boot
+process as well as to assisting in entering deep low power state
+(suspend to ram), and also offloading DRAM memory clock scaling on
+some platforms. The binding document defines the resources that would
+be used by the BPMP T210 firmware driver, which can create the
+interprocessor communication (IPC) between the CPU and BPMP.
+
+Required properties:
+- compatible
+    Array of strings
+    One of:
+    - "nvidia,tegra210-bpmp"
+- reg: physical base address and length for HW synchornization primitives
+       1) base address and length to Tegra 'atomics' hardware
+       2) base address and length to Tegra 'semaphore' hardware
+- interrupts: specifies the interrupt number for receiving messages ("rx")
+              and for triggering messages ("tx")
+
+Optional properties:
+- #clock-cells : Should be 1 for platforms where DRAM clock control is
+                 offloaded to bpmp.
+
+Example:
+
+bpmp@70016000 {
+	compatible = "nvidia,tegra210-bpmp";
+	reg = <0x0 0x70016000 0x0 0x2000
+	       0x0 0x60001000 0x0 0x1000>;
+	interrupts = <GIC_SPI 6 IRQ_TYPE_EDGE_RISING>,
+		     <GIC_SPI 4 IRQ_TYPE_EDGE_RISING>;
+	interrupt-names = "tx", "rx";
+};
--- a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt
+++ b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt
@ -13,6 +13,8 @@ Required properties:
      + allwinner,sun8i-h3-mali
      + allwinner,sun50i-a64-mali
      + allwinner,sun50i-h5-mali
+      + amlogic,meson8-mali
+      + amlogic,meson8b-mali
      + amlogic,meson-gxbb-mali
      + amlogic,meson-gxl-mali
      + rockchip,rk3036-mali
@ -82,6 +84,10 @@ to specify one more vendor-specific compatible, among:
    Required properties:
      * resets: phandle to the reset line for the GPU

+  - amlogic,meson8-mali and amlogic,meson8b-mali
+    Required properties:
+      * resets: phandle to the reset line for the GPU
+
  - Rockchip variants:
    Required properties:
      * resets: phandle to the reset line for the GPU
--- a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
@ -2,7 +2,12 @@
 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

 Required properties:
+- mfd
+	compatible: Should be
+		"ti,am3359-tscadc" for AM335x/AM437x SoCs
+		"ti,am654-tscadc", "ti,am3359-tscadc" for AM654 SoCs
 - child "tsc"
+	compatible: Should be "ti,am3359-tsc".
 	ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen
 		  support on the platform.
 	ti,x-plate-resistance: X plate resistance
@ -25,6 +30,9 @@ Required properties:
 			AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
 			XP  = 0, XN = 1, YP = 2, YN = 3.
 - child "adc"
+	compatible: Should be
+		    "ti,am3359-adc" for AM335x/AM437x SoCs
+		    "ti,am654-adc", "ti,am3359-adc" for AM654 SoCs
 	ti,adc-channels: List of analog inputs available for ADC.
 			 AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.

--- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
@ -9,6 +9,7 @@ Required properties:
 	"mediatek,mt8135-sysirq", "mediatek,mt6577-sysirq": for MT8135
 	"mediatek,mt8127-sysirq", "mediatek,mt6577-sysirq": for MT8127
 	"mediatek,mt7622-sysirq", "mediatek,mt6577-sysirq": for MT7622
+	"mediatek,mt7623-sysirq", "mediatek,mt6577-sysirq": for MT7623
 	"mediatek,mt6795-sysirq", "mediatek,mt6577-sysirq": for MT6795
 	"mediatek,mt6797-sysirq", "mediatek,mt6577-sysirq": for MT6797
 	"mediatek,mt6765-sysirq", "mediatek,mt6577-sysirq": for MT6765
--- a/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt
+++ b/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt
@ -1,4 +1,4 @@
-TI CPSW Phy mode Selection Device Tree Bindings
+TI CPSW Phy mode Selection Device Tree Bindings (DEPRECATED)
 -----------------------------------------------

 Required properties:
--- a/Documentation/devicetree/bindings/sram/sunxi-sram.txt
+++ b/Documentation/devicetree/bindings/sram/sunxi-sram.txt
@ -63,6 +63,7 @@ The valid sections compatible for H5 are:

 The valid sections compatible for H6 are:
    - allwinner,sun50i-h6-sram-c, allwinner,sun50i-a64-sram-c
+    - allwinner,sun50i-h6-sram-c1, allwinner,sun4i-a10-sram-c1

 The valid sections compatible for F1C100s are:
    - allwinner,suniv-f1c100s-sram-d, allwinner,sun4i-a10-sram-d
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@ -24,6 +24,7 @@ amarula	Amarula Solutions
 amazon	Amazon.com, Inc.
 amcc	Applied Micro Circuits Corporation (APM, formally AMCC)
 amd	Advanced Micro Devices (AMD), Inc.
+amediatech	Shenzhen Amediatech Technology Co., Ltd
 amlogic	Amlogic, Inc.
 ampire	Ampire Co., Ltd.
 ams	AMS AG
@ -65,6 +66,7 @@ bticino Bticino International
 calxeda	Calxeda
 capella	Capella Microsystems, Inc
 cascoda	Cascoda, Ltd.
+catalyst	Catalyst Semiconductor, Inc.
 cavium	Cavium, Inc.
 cdns	Cadence Design Systems Inc.
 cdtech	CDTech(H.K.) Electronics Limited
@ -108,11 +110,13 @@ dongwoon	Dongwoon Anatech
 dptechnics	DPTechnics
 dragino	Dragino Technology Co., Limited
 ea	Embedded Artists AB
+ebs-systart EBS-SYSTART GmbH
 ebv	EBV Elektronik
 eckelmann	Eckelmann AG
 edt	Emerging Display Technologies
 eeti	eGalax_eMPIA Technology Inc
 elan	Elan Microelectronic Corp.
+elgin	Elgin S/A.
 embest	Shenzhen Embest Technology Co., Ltd.
 emlid	Emlid, Ltd.
 emmicro	EM Microelectronic
@ -273,6 +277,7 @@ nintendo	Nintendo
 nlt	NLT Technologies, Ltd.
 nokia	Nokia
 nordic	Nordic Semiconductor
+novtech NovTech, Inc.
 nutsboard	NutsBoard
 nuvoton	Nuvoton Technology Corporation
 nvd	New Vision Display
--- a/4
+++ b/4
@ -1989,7 +1989,7 @@ Q:	http://patchwork.kernel.org/project/linux-renesas-soc/list/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git next
 S:	Supported
 F:	arch/arm64/boot/dts/renesas/
-F:	Documentation/devicetree/bindings/arm/shmobile.txt
+F:	Documentation/devicetree/bindings/arm/renesas.yaml
 F:	drivers/soc/renesas/
 F:	include/linux/soc/renesas/

@ -2110,7 +2110,7 @@ F:	arch/arm/boot/dts/sh*
 F:	arch/arm/configs/shmobile_defconfig
 F:	arch/arm/include/debug/renesas-scif.S
 F:	arch/arm/mach-shmobile/
-F:	Documentation/devicetree/bindings/arm/shmobile.txt
+F:	Documentation/devicetree/bindings/arm/renesas.yaml
 F:	drivers/soc/renesas/
 F:	include/linux/soc/renesas/

--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@ -79,6 +79,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2835-rpi-a-plus.dtb \
 	bcm2835-rpi-cm1-io1.dtb \
 	bcm2836-rpi-2-b.dtb \
+	bcm2837-rpi-3-a-plus.dtb \
 	bcm2837-rpi-3-b.dtb \
 	bcm2837-rpi-3-b-plus.dtb \
 	bcm2837-rpi-cm3-io3.dtb \
@ -115,6 +116,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm47094-luxul-xwr-3100.dtb \
 	bcm47094-luxul-xwr-3150-v1.dtb \
 	bcm47094-netgear-r8500.dtb \
+	bcm47094-phicomm-k3.dtb \
 	bcm94708.dtb \
 	bcm94709.dtb \
 	bcm953012er.dtb \
@ -313,7 +315,8 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
 dtb-$(CONFIG_ARCH_LPC18XX) += \
 	lpc4337-ciaa.dtb \
 	lpc4350-hitex-eval.dtb \
-	lpc4357-ea4357-devkit.dtb
+	lpc4357-ea4357-devkit.dtb \
+	lpc4357-myd-lpc4357.dtb
 dtb-$(CONFIG_ARCH_LPC32XX) += \
 	lpc3250-ea3250.dtb \
 	lpc3250-phy3250.dtb
@ -445,6 +448,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-wandboard.dtb \
 	imx6dl-wandboard-revb1.dtb \
 	imx6dl-wandboard-revd1.dtb \
+	imx6dl-yapp4-draco.dtb \
+	imx6dl-yapp4-hydra.dtb \
+	imx6dl-yapp4-ursa.dtb \
 	imx6q-apalis-eval.dtb \
 	imx6q-apalis-ixora.dtb \
 	imx6q-apalis-ixora-v1.1.dtb \
@ -561,6 +567,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
 	imx6ul-opos6uldev.dtb \
 	imx6ul-pico-hobbit.dtb \
 	imx6ul-pico-pi.dtb \
+	imx6ul-phytec-phyboard-segin-full.dtb \
 	imx6ul-tx6ul-0010.dtb \
 	imx6ul-tx6ul-0011.dtb \
 	imx6ul-tx6ul-mainboard.dtb \
@ -599,6 +606,7 @@ dtb-$(CONFIG_SOC_VF610) += \
 	vf610-zii-dev-rev-b.dtb \
 	vf610-zii-dev-rev-c.dtb \
 	vf610-zii-scu4-aib.dtb \
+	vf610-zii-ssmb-dtu.dtb \
 	vf610-zii-ssmb-spu3.dtb
 dtb-$(CONFIG_ARCH_MXS) += \
 	imx23-evk.dtb \
@ -700,6 +708,7 @@ dtb-$(CONFIG_ARCH_OMAP3) += \
 	omap3-thunder.dtb \
 	omap3-zoom3.dtb
 dtb-$(CONFIG_SOC_TI81XX) += \
+	am3874-iceboard.dtb \
 	dm8148-evm.dtb \
 	dm8148-t410.dtb \
 	dm8168-evm.dtb \
@ -719,6 +728,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-cm-t335.dtb \
 	am335x-evm.dtb \
 	am335x-evmsk.dtb \
+	am335x-guardian.dtb \
 	am335x-icev2.dtb \
 	am335x-lxm.dtb \
 	am335x-moxa-uc-2101.dtb \
@ -843,6 +853,7 @@ dtb-$(CONFIG_ARCH_RENESAS) += \
 	r7s72100-genmai.dtb \
 	r7s72100-gr-peach.dtb \
 	r7s72100-rskrza1.dtb \
+	r7s9210-rza2mevb.dtb \
 	r8a73a4-ape6evm.dtb \
 	r8a7740-armadillo800eva.dtb \
 	r8a7743-iwg20d-q7.dtb \
@ -868,6 +879,7 @@ dtb-$(CONFIG_ARCH_RENESAS) += \
 	r9a06g032-rzn1d400-db.dtb \
 	sh73a0-kzm9g.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += \
+	rv1108-elgin-r1.dtb \
 	rv1108-evb.dtb \
 	rk3036-evb.dtb \
 	rk3036-kylin.dtb \
@ -919,6 +931,7 @@ dtb-$(CONFIG_ARCH_SOCFPGA) += \
 	socfpga_arria10_socdk_nand.dtb \
 	socfpga_arria10_socdk_qspi.dtb \
 	socfpga_arria10_socdk_sdmmc.dtb \
+	socfpga_cyclone5_chameleon96.dtb \
 	socfpga_cyclone5_mcvevk.dtb \
 	socfpga_cyclone5_socdk.dtb \
 	socfpga_cyclone5_de0_nano_soc.dtb \
--- a/arch/arm/boot/dts/alphascale-asm9260.dtsi
+++ b/arch/arm/boot/dts/alphascale-asm9260.dtsi
@ -4,10 +4,11 @@
 * Licensed under the X11 license or the GPL v2 (or later)
 */

-#include "skeleton.dtsi"
 #include <dt-bindings/clock/alphascale,asm9260.h>

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	interrupt-parent = <&icoll>;

 	memory {
--- a/arch/arm/boot/dts/alpine.dtsi
+++ b/arch/arm/boot/dts/alpine.dtsi
@ -25,12 +25,18 @@
 */

 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include "skeleton64.dtsi"

 / {
+	#address-cells = <2>;
+	#size-cells = <2>;
 	/* SOC compatibility */
 	compatible = "al,alpine";

+	memory {
+		device_type = "memory";
+		reg = <0 0 0 0>;
+	};
+
 	/* CPU Configuration */
 	cpus {
 		#address-cells = <1>;
--- a/arch/arm/boot/dts/am335x-baltos-ir2110.dts
+++ b/arch/arm/boot/dts/am335x-baltos-ir2110.dts
@ -72,7 +72,3 @@
 	dual_emac_res_vlan = <2>;
 	phy-handle = <&phy1>;
 };
-
-&phy_sel {
-	rmii-clock-ext = <1>;
-};
--- a/arch/arm/boot/dts/am335x-baltos-ir3220.dts
+++ b/arch/arm/boot/dts/am335x-baltos-ir3220.dts
@ -114,7 +114,3 @@
 	dual_emac_res_vlan = <2>;
 	phy-handle = <&phy1>;
 };
-
-&phy_sel {
-	rmii-clock-ext = <1>;
-};
--- a/arch/arm/boot/dts/am335x-baltos-ir5221.dts
+++ b/arch/arm/boot/dts/am335x-baltos-ir5221.dts
@ -133,10 +133,6 @@
 	phy-handle = <&phy1>;
 };

-&phy_sel {
-	rmii-clock-ext = <1>;
-};
-
 &dcan1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&dcan1_pins>;
--- a/arch/arm/boot/dts/am335x-chiliboard.dts
+++ b/arch/arm/boot/dts/am335x-chiliboard.dts
@ -14,6 +14,10 @@
 	compatible = "grinn,am335x-chiliboard", "grinn,am335x-chilisom",
 		     "ti,am33xx";

+	chosen {
+		stdout-path = &uart0;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@ -151,10 +155,6 @@
 	phy-mode = "rmii";
 };

-&phy_sel {
-	rmii-clock-ext;
-};
-
 /* USB */
 &usb {
 	status = "okay";
--- a/arch/arm/boot/dts/am335x-guardian.dts
+++ b/arch/arm/boot/dts/am335x-guardian.dts
@ -0,0 +1,511 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2018 Robert Bosch Power Tools GmbH
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Bosch AM335x Guardian";
+	compatible = "bosch,am335x-guardian", "ti,am33xx";
+
+	chosen {
+		stdout-path = &uart0;
+		tick-timer = &timer2;
+	};
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&dcdc2_reg>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pins>;
+
+		button21 {
+			label = "guardian-power-button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio2 21 0>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_pins>;
+
+		led1 {
+			label = "green:heartbeat";
+			gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led2 {
+			label = "green:mmc0";
+			gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+	};
+
+	panel {
+		compatible = "ti,tilcdc,panel";
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&lcd_pins_default &lcd_disen_pins>;
+		pinctrl-1 = <&lcd_pins_sleep>;
+
+		display-timings {
+			320x240 {
+				hactive         = <320>;
+				vactive         = <240>;
+				hback-porch     = <68>;
+				hfront-porch    = <20>;
+				hsync-len       = <1>;
+				vback-porch     = <18>;
+				vfront-porch    = <4>;
+				vsync-len       = <1>;
+				clock-frequency = <9000000>;
+				hsync-active    = <0>;
+				vsync-active    = <0>;
+			};
+		};
+		panel-info {
+			ac-bias           = <255>;
+			ac-bias-intrpt    = <0>;
+			dma-burst-sz      = <16>;
+			bpp               = <24>;
+			bus-width         = <16>;
+			fdd               = <0x80>;
+			sync-edge         = <0>;
+			sync-ctrl         = <1>;
+			raster-order      = <0>;
+			fifo-th           = <0>;
+		};
+
+	};
+
+	pwm7: dmtimer-pwm {
+		compatible = "ti,omap-dmtimer-pwm";
+		ti,timers = <&timer7>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dmtimer7_pins>;
+	};
+
+	vmmcsd_fixed: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&cppi41dma  {
+	status = "okay";
+};
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nandflash_pins>;
+	ranges = <0 0 0x08000000 0x1000000>;  /* CS0: 16MB for NAND */
+	status = "okay";
+
+	nand@0,0 {
+		compatible = "ti,omap2-nand";
+		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>; /* termcount */
+		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
+		ti,nand-ecc-opt = "bch16";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+
+		/*
+		 * MTD partition table
+		 *
+		 * All SPL-* partitions are sized to minimal length which can
+		 * be independently programmable. For NAND flash this is equal
+		 * to size of erase-block.
+		 */
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "SPL";
+			reg = <0x0 0x40000>;
+		};
+
+		partition@1 {
+			label = "SPL.backup1";
+			reg = <0x40000  0x40000>;
+		};
+
+		partition@2 {
+			label = "SPL.backup2";
+			reg = <0x80000  0x40000>;
+		};
+
+		partition@3 {
+			label = "SPL.backup3";
+			reg = <0xc0000  0x40000>;
+		};
+
+		partition@4 {
+			label = "u-boot";
+			reg = <0x100000 0x100000>;
+		};
+
+		partition@5 {
+			label = "u-boot.backup1";
+			reg = <0x200000 0x100000>;
+		};
+
+		partition@6 {
+			label = "u-boot-env";
+			reg = <0x300000 0x40000>;
+		};
+
+		partition@7 {
+			label = "u-boot-env.backup1";
+			reg = <0x340000 0x40000>;
+		};
+
+		partition@8 {
+			label = "UBI";
+			reg = <0x380000 0x1fc80000>;
+		};
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	tps: tps@24 {
+		reg = <0x24>;
+	};
+};
+
+&lcdc {
+	blue-and-red-wiring = "crossed";
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <0x4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&vmmcsd_fixed>;
+	status = "okay";
+};
+
+&rtc {
+	clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
+	clock-names = "ext-clk", "int-clk";
+	system-power-controller;
+};
+
+&spi0 {
+	ti,pindir-d0-out-d1-in;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+	status = "okay";
+};
+
+#include "tps65217.dtsi"
+
+&tps {
+	ti,pmic-shutdown-controller;
+	interrupt-parent = <&intc>;
+	interrupts = <7>; /* NMI */
+
+	backlight {
+		isel = <1>;  /* 1 - ISET1, 2 ISET2 */
+		fdim = <100>; /* TPS65217_BL_FDIM_100HZ */
+		default-brightness = <100>;
+	};
+
+	regulators {
+		dcdc1_reg: regulator@0 {
+			regulator-name = "vdds_dpr";
+			regulator-always-on;
+		};
+
+		dcdc2_reg: regulator@1 {
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <1351500>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		dcdc3_reg: regulator@2 {
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <1150000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		ldo1_reg: regulator@3 {
+			regulator-name = "vio,vrtc,vdds";
+			regulator-always-on;
+		};
+
+		ldo2_reg: regulator@4 {
+			regulator-name = "vdd_3v3aux";
+			regulator-always-on;
+		};
+
+		ldo3_reg: regulator@5 {
+			regulator-name = "vdd_1v8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		ldo4_reg: regulator@6 {
+			regulator-name = "vdd_3v3a";
+			regulator-always-on;
+		};
+	};
+};
+
+&tscadc {
+	status = "okay";
+
+	adc {
+		ti,adc-channels = <0 1 2 3 4 5 6>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_ctrl_mod {
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&am33xx_pinmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&clkout2_pin &gpio_pins>;
+
+	clkout2_pin: pinmux_clkout2_pin {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9b4, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
+		>;
+	};
+
+	dmtimer7_pins: pinmux_dmtimer7_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x968, PIN_OUTPUT | MUX_MODE5)
+		>;
+	};
+
+	gpio_keys_pins: pinmux_gpio_keys_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x940, PIN_INPUT | MUX_MODE7)
+		>;
+	};
+
+	gpio_pins: pinmux_gpio_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x928, PIN_OUTPUT | MUX_MODE7)
+			AM33XX_IOPAD(0x990, PIN_OUTPUT | MUX_MODE7)
+		>;
+	};
+
+	i2c0_pins: pinmux_i2c0_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0)
+			AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0)
+		>;
+	};
+
+	lcd_disen_pins: pinmux_lcd_disen_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9a4, PIN_OUTPUT_PULLUP | SLEWCTRL_SLOW | MUX_MODE7)
+		>;
+	};
+
+	lcd_pins_default: pinmux_lcd_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x820, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			AM33XX_IOPAD(0x824, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			AM33XX_IOPAD(0x828, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			AM33XX_IOPAD(0x82c, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			AM33XX_IOPAD(0x830, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			AM33XX_IOPAD(0x834, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			AM33XX_IOPAD(0x838, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			AM33XX_IOPAD(0x83c, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			AM33XX_IOPAD(0x8a0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8a4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8a8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8ac, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8b0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8b4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8b8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8bc, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8c0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8c4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8c8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8cc, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8d0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8d4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8d8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8dc, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8e0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8e4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8e8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			AM33XX_IOPAD(0x8ec, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+		>;
+	};
+
+	lcd_pins_sleep: pinmux_lcd_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x8a0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8a4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8a8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8ac, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8b0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8b4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8b8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8bc, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8c0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8c4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8c8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8cc, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8d0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8d4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8d8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8dc, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8e0, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8e4, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8e8, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7)
+			AM33XX_IOPAD(0x8ec, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7)
+		>;
+	};
+
+	leds_pins: pinmux_leds_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x868, PIN_OUTPUT | MUX_MODE7)
+			AM33XX_IOPAD(0x86c, PIN_OUTPUT | MUX_MODE7)
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0)
+			AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0)
+			AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0)
+			AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0)
+			AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0)
+			AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0)
+			AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7)
+		>;
+	};
+
+	spi0_pins: pinmux_spi0_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x950, PIN_OUTPUT_PULLDOWN | MUX_MODE0)
+			AM33XX_IOPAD(0x954, PIN_OUTPUT_PULLUP | MUX_MODE0)
+			AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE0)
+			AM33XX_IOPAD(0x95c, PIN_OUTPUT_PULLUP | MUX_MODE0)
+		>;
+	};
+
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0)
+			AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0)
+		>;
+	};
+
+	nandflash_pins: pinmux_nandflash_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x800, PIN_INPUT | MUX_MODE0)
+			AM33XX_IOPAD(0x804, PIN_INPUT | MUX_MODE0)
+			AM33XX_IOPAD(0x808, PIN_INPUT | MUX_MODE0)
+			AM33XX_IOPAD(0x80c, PIN_INPUT | MUX_MODE0)
+			AM33XX_IOPAD(0x810, PIN_INPUT | MUX_MODE0)
+			AM33XX_IOPAD(0x814, PIN_INPUT | MUX_MODE0)
+			AM33XX_IOPAD(0x818, PIN_INPUT | MUX_MODE0)
+			AM33XX_IOPAD(0x81c, PIN_INPUT | MUX_MODE0)
+			AM33XX_IOPAD(0x870, PIN_INPUT | MUX_MODE0)
+			AM33XX_IOPAD(0x874, PIN_OUTPUT | MUX_MODE0)
+			AM33XX_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0)
+			AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0)
+			AM33XX_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0)
+			AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0)
+			AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0)
+		>;
+	};
+};
--- a/arch/arm/boot/dts/am335x-icev2.dts
+++ b/arch/arm/boot/dts/am335x-icev2.dts
@ -484,10 +484,6 @@
 	dual_emac;
 };

-&phy_sel {
-	rmii-clock-ext;
-};
-
 &davinci_mdio {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
--- a/arch/arm/boot/dts/am335x-igep0033.dtsi
+++ b/arch/arm/boot/dts/am335x-igep0033.dtsi
@ -123,10 +123,6 @@
 	phy-mode = "rmii";
 };

-&phy_sel {
-	rmii-clock-ext;
-};
-
 &elm {
 	status = "okay";
 };
--- a/arch/arm/boot/dts/am335x-lxm.dts
+++ b/arch/arm/boot/dts/am335x-lxm.dts
@ -328,10 +328,6 @@
 	dual_emac_res_vlan = <3>;
 };

-&phy_sel {
-	rmii-clock-ext;
-};
-
 &mac {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
--- a/arch/arm/boot/dts/am335x-moxa-uc-2100-common.dtsi
+++ b/arch/arm/boot/dts/am335x-moxa-uc-2100-common.dtsi
@ -159,11 +159,6 @@
 	status = "okay";
 };

-&phy_sel {
-	reg= <0x44e10650 0xf5>;
-	rmii-clock-ext;
-};
-
 &sham {
 	status = "okay";
 };
--- a/arch/arm/boot/dts/am335x-moxa-uc-8100-me-t.dts
+++ b/arch/arm/boot/dts/am335x-moxa-uc-8100-me-t.dts
@ -446,11 +446,6 @@
 	dual_emac_res_vlan = <2>;
 };

-&phy_sel {
-	reg= <0x44e10650 0xf5>;
-	rmii-clock-ext;
-};
-
 &sham {
 	status = "okay";
 };
--- a/arch/arm/boot/dts/am335x-phycore-som.dtsi
+++ b/arch/arm/boot/dts/am335x-phycore-som.dtsi
@ -100,10 +100,6 @@
 	status = "okay";
 };

-&phy_sel {
-	rmii-clock-ext;
-};
-
 /* I2C Busses */
 &am33xx_pinmux {
 	i2c0_pins: pinmux_i2c0 {
--- a/arch/arm/boot/dts/am335x-shc.dts
+++ b/arch/arm/boot/dts/am335x-shc.dts
@ -1,11 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
 * support for the bosch am335x based shc c3 board
 *
 * Copyright, C) 2015 Heiko Schocher <hs@denx.de>
 *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
 */
 /dts-v1/;

--- a/arch/arm/boot/dts/am33xx-l4.dtsi
+++ b/arch/arm/boot/dts/am33xx-l4.dtsi
@ -279,17 +279,9 @@
 				#pinctrl-cells = <1>;
 				ranges = <0 0 0x2000>;

-				phy_sel: cpsw-phy-sel@650 {
-					compatible = "ti,am3352-cpsw-phy-sel";
-					reg= <0x650 0x4>;
-					reg-names = "gmii-sel";
-				};
-
 				am33xx_pinmux: pinmux@800 {
 					compatible = "pinctrl-single";
 					reg = <0x800 0x238>;
-					#address-cells = <1>;
-					#size-cells = <0>;
 					#pinctrl-cells = <1>;
 					pinctrl-single,register-width = <32>;
 					pinctrl-single,function-mask = <0x7f>;
@ -302,6 +294,12 @@
 					#size-cells = <1>;
 					ranges = <0 0 0x800>;

+					phy_gmii_sel: phy-gmii-sel {
+						compatible = "ti,am3352-phy-gmii-sel";
+						reg = <0x650 0x4>;
+						#phy-cells = <2>;
+					};
+
 					scm_clocks: clocks {
 						#address-cells = <1>;
 						#size-cells = <0>;
@ -717,7 +715,6 @@
 				interrupts = <40 41 42 43>;
 				ranges = <0 0 0x8000>;
 				syscon = <&scm_conf>;
-				cpsw-phy-sel = <&phy_sel>;
 				status = "disabled";

 				davinci_mdio: mdio@1000 {
@ -733,11 +730,13 @@
 				cpsw_emac0: slave@200 {
 					/* Filled in by U-Boot */
 					mac-address = [ 00 00 00 00 00 00 ];
+					phys = <&phy_gmii_sel 1 1>;
 				};

 				cpsw_emac1: slave@300 {
 					/* Filled in by U-Boot */
 					mac-address = [ 00 00 00 00 00 00 ];
+					phys = <&phy_gmii_sel 2 1>;
 				};
 			};
 		};
--- a/arch/arm/boot/dts/am3874-iceboard.dts
+++ b/arch/arm/boot/dts/am3874-iceboard.dts
@ -0,0 +1,496 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device tree for Winterland IceBoard
+ *
+ * http://mcgillcosmology.com
+ * http://threespeedlogic.com
+ *
+ * This is an ARM + FPGA instrumentation board used at telescopes in
+ * Antarctica (the South Pole Telescope), Chile (POLARBEAR), and at the DRAO
+ * observatory in British Columbia (CHIME).
+ *
+ * Copyright (c) 2019 Three-Speed Logic, Inc. <gsmecher@threespeedlogic.com>
+ */
+
+/dts-v1/;
+
+#include "dm814x.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Winterland IceBoard";
+	compatible = "ti,dm8148", "ti,dm814";
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+		bootargs = "earlycon";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;	/* 1 GB */
+	};
+
+	vmmcsd_fixed: fixedregulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+/* The MAC provides internal delay for the transmit path ONLY, which is enabled
+ * provided no -id/-txid/-rxid suffix is provided to "phy-mode".
+ *
+ * The receive path is delayed at the PHY. The recommended register settings
+ * are 0xf0 for the control bits, and 0x7777 for the data bits. However, the
+ * conversion code in the kernel lies: the PHY's registers are 120 ps per tap,
+ * and the kernel assumes 200 ps per tap. So we have fudged the numbers here to
+ * obtain the correct register settings.
+ */
+&mac { dual_emac = <1>; };
+&cpsw_emac0 {
+	phy-handle = <&ethphy0>;
+	phy-mode = "rgmii";
+	dual_emac_res_vlan = <1>;
+};
+&cpsw_emac1 {
+	phy-handle = <&ethphy1>;
+	phy-mode = "rgmii";
+	dual_emac_res_vlan = <2>;
+};
+
+&davinci_mdio {
+	ethphy0: ethernet-phy@0 {
+		reg = <0x2>;
+
+		rxc-skew-ps = <3000>;
+		rxdv-skew-ps = <0>;
+
+		rxd3-skew-ps = <0>;
+		rxd2-skew-ps = <0>;
+		rxd1-skew-ps = <0>;
+		rxd0-skew-ps = <0>;
+
+		phy-reset-gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
+	};
+
+	ethphy1: ethernet-phy@1 {
+		reg = <0x1>;
+
+		rxc-skew-ps = <3000>;
+		rxdv-skew-ps = <0>;
+
+		rxd3-skew-ps = <0>;
+		rxd2-skew-ps = <0>;
+		rxd1-skew-ps = <0>;
+		rxd0-skew-ps = <0>;
+
+		phy-reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&mmc1 { status = "disabled"; };
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <4>;
+};
+&mmc3 { status = "disabled"; };
+
+&i2c1 {
+	/* Most I2C activity happens through this port, with the sole exception
+	 * of the backplane. Since there are multiply assigned addresses, the
+	 * "i2c-mux-idle-disconnect" is important.
+	 */
+
+	pca9548@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@0 {
+			/* FMC A */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			i2c-mux-idle-disconnect;
+		};
+
+		i2c@1 {
+			/* FMC B */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			i2c-mux-idle-disconnect;
+		};
+
+		i2c@2 {
+			/* QSFP A */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			i2c-mux-idle-disconnect;
+		};
+
+		i2c@3 {
+			/* QSFP B */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			i2c-mux-idle-disconnect;
+		};
+
+		i2c@4 {
+			/* SFP */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			i2c-mux-idle-disconnect;
+		};
+
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			i2c-mux-idle-disconnect;
+
+			ina230@40 { compatible = "ti,ina230"; reg = <0x40>; shunt-resistor = <5000>; };
+			ina230@41 { compatible = "ti,ina230"; reg = <0x41>; shunt-resistor = <5000>; };
+			ina230@42 { compatible = "ti,ina230"; reg = <0x42>; shunt-resistor = <5000>; };
+
+			ina230@44 { compatible = "ti,ina230"; reg = <0x44>; shunt-resistor = <5000>; };
+			ina230@45 { compatible = "ti,ina230"; reg = <0x45>; shunt-resistor = <5000>; };
+			ina230@46 { compatible = "ti,ina230"; reg = <0x46>; shunt-resistor = <5000>; };
+
+			ina230@47 { compatible = "ti,ina230"; reg = <0x47>; shunt-resistor = <5500>; };
+			ina230@48 { compatible = "ti,ina230"; reg = <0x48>; shunt-resistor = <2360>; };
+			ina230@49 { compatible = "ti,ina230"; reg = <0x49>; shunt-resistor = <2360>; };
+			ina230@43 { compatible = "ti,ina230"; reg = <0x43>; shunt-resistor = <2360>; };
+			ina230@4b { compatible = "ti,ina230"; reg = <0x4b>; shunt-resistor = <5500>; };
+			ina230@4c { compatible = "ti,ina230"; reg = <0x4c>; shunt-resistor = <2360>; };
+			ina230@4d { compatible = "ti,ina230"; reg = <0x4d>; shunt-resistor = <770>; };
+			ina230@4e { compatible = "ti,ina230"; reg = <0x4e>; shunt-resistor = <770>; };
+			ina230@4f { compatible = "ti,ina230"; reg = <0x4f>; shunt-resistor = <770>; };
+		};
+
+		i2c@6 {
+			/* Backplane */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			i2c-mux-idle-disconnect;
+		};
+
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			i2c-mux-idle-disconnect;
+
+			u41: pca9575@20 {
+				compatible = "nxp,pca9575";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				gpio-line-names =
+					"FMCA_EN_12V0", "FMCA_EN_3V3", "FMCA_EN_VADJ", "FMCA_PG_M2C",
+					"FMCA_PG_C2M", "FMCA_PRSNT_M2C_L", "FMCA_CLK_DIR", "SFP_LOS",
+					"FMCB_EN_12V0", "FMCB_EN_3V3", "FMCB_EN_VADJ", "FMCB_PG_M2C",
+					"FMCB_PG_C2M", "FMCB_PRSNT_M2C_L", "FMCB_CLK_DIR", "SFP_ModPrsL";
+				reset_gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+			};
+
+			u42: pca9575@21 {
+				compatible = "nxp,pca9575";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-line-names =
+					"QSFPA_ModPrsL", "QSFPA_IntL", "QSFPA_ResetL", "QSFPA_ModSelL",
+					"QSFPA_LPMode", "QSFPB_ModPrsL", "QSFPB_IntL", "QSFPB_ResetL",
+					"SFP_TxFault", "SFP_TxDisable", "SFP_RS0", "SFP_RS1",
+					"QSFPB_ModSelL", "QSFPB_LPMode", "SEL_SFP", "ARM_MR";
+				reset_gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+			};
+
+			u48: pca9575@22 {
+				compatible = "nxp,pca9575";
+				reg=<0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				sw-gpios = <&u48 0 0>, <&u48 1 0>, <&u48 2 0>, <&u48 3 0>,
+					<&u48 4 0>, <&u48 5 0>, <&u48 6 0>, <&u48 7 0>;
+				led-gpios = <&u48 7 0>, <&u48 6 0>, <&u48 5 0>, <&u48 4 0>,
+					<&u48 3 0>, <&u48 2 0>, <&u48 1 0>, <&u48 0 0>;
+
+				gpio-line-names =
+					"GP_SW1", "GP_SW2", "GP_SW3", "GP_SW4",
+					"GP_SW5", "GP_SW6", "GP_SW7", "GP_SW8",
+					"GP_LED8", "GP_LED7", "GP_LED6", "GP_LED5",
+					"GP_LED4", "GP_LED3", "GP_LED2", "GP_LED1";
+				reset_gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+			};
+
+			u59: pca9575@23 {
+				compatible = "nxp,pca9575";
+				reg=<0x23>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-line-names =
+					"GP_LED9", "GP_LED10", "GP_LED11", "GP_LED12",
+					"GTX1V8PowerFault", "PHYAPowerFault", "PHYBPowerFault", "ArmPowerFault",
+					"BP_SLOW_GPIO0", "BP_SLOW_GPIO1", "BP_SLOW_GPIO2", "BP_SLOW_GPIO3",
+					"BP_SLOW_GPIO4", "BP_SLOW_GPIO5", "__unused_u59_p16", "__unused_u59_p17";
+				reset_gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+			};
+
+			tmp100@48 { compatible = "ti,tmp100"; reg = <0x48>; };
+			tmp100@4a { compatible = "ti,tmp100"; reg = <0x4a>; };
+			tmp100@4b { compatible = "ti,tmp100"; reg = <0x4b>; };
+			tmp100@4c { compatible = "ti,tmp100"; reg = <0x4c>; };
+
+			/* EEPROM bank and serial number are treated as separate devices */
+			at24c01@57 { compatible = "atmel,24c01"; reg = <0x57>; };
+			at24cs01@5f { compatible = "atmel,24cs01"; reg = <0x5f>; };
+		};
+	};
+};
+
+&i2c2 {
+	pca9548@71 {
+		compatible = "nxp,pca9548";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@6 {
+			/* Backplane */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			multi-master;
+
+			/* All backplanes should have this -- it's how we know they're there. */
+			at24c08@54 { compatible="atmel,24c08"; reg=<0x54>; };
+			at24cs08@5c { compatible="atmel,24cs08"; reg=<0x5c>; };
+
+			/* 16 slot backplane */
+			tmp421@4d { compatible="ti,tmp421"; reg=<0x4d>; };
+			tmp421@4e { compatible="ti,tmp421"; reg=<0x4e>; };
+			ina230@40 { compatible = "ti,ina230"; reg = <0x40>; shunt-resistor = <2360>; };
+			amc6821@18 { compatible = "ti,amc6821"; reg = <0x18>; };
+
+			/* Single slot backplane */
+		};
+	};
+};
+
+&pincntl {
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			DM814X_IOPAD(0x0800, PIN_INPUT | 0x1)	/* SD1_CLK */
+			DM814X_IOPAD(0x0804, PIN_INPUT_PULLUP | 0x1)	/* SD1_CMD */
+			DM814X_IOPAD(0x0808, PIN_INPUT_PULLUP | 0x1)	/* SD1_DAT[0] */
+			DM814X_IOPAD(0x080c, PIN_INPUT_PULLUP | 0x1)	/* SD1_DAT[1] */
+			DM814X_IOPAD(0x0810, PIN_INPUT_PULLUP | 0x1)	/* SD1_DAT[2] */
+			DM814X_IOPAD(0x0814, PIN_INPUT_PULLUP | 0x1)	/* SD1_DAT[3] */
+			DM814X_IOPAD(0x0924, PIN_INPUT_PULLUP | 0x40)	/* SD1_POW */
+			DM814X_IOPAD(0x0928, PIN_INPUT | 0x40)	/* SD1_SDWP */
+			DM814X_IOPAD(0x093C, PIN_INPUT | 0x2)	/* SD1_SDCD */
+			>;
+	};
+
+	usb0_pins: pinmux_usb0_pins {
+		pinctrl-single,pins = <
+			DM814X_IOPAD(0x0c34, PIN_OUTPUT | 0x1)	/* USB0_DRVVBUS */
+			>;
+	};
+
+	usb1_pins: pinmux_usb1_pins {
+		pinctrl-single,pins = <
+			DM814X_IOPAD(0x0834, PIN_OUTPUT | 0x80)	/* USB1_DRVVBUS */
+			>;
+	};
+
+	gpio1_pins: pinmux_gpio1_pins {
+		pinctrl-single,pins = <
+			DM814X_IOPAD(0x081c, PIN_OUTPUT | 0x80)	/* PROGRAM_B */
+			DM814X_IOPAD(0x0820, PIN_INPUT | 0x80)	/* INIT_B */
+			DM814X_IOPAD(0x0824, PIN_INPUT | 0x80)	/* DONE */
+
+			DM814X_IOPAD(0x0838, PIN_INPUT_PULLUP | 0x80) /* FMCA_TMS */
+			DM814X_IOPAD(0x083c, PIN_INPUT_PULLUP | 0x80) /* FMCA_TCK */
+			DM814X_IOPAD(0x0898, PIN_INPUT_PULLUP | 0x80) /* FMCA_TDO */
+			DM814X_IOPAD(0x089c, PIN_INPUT_PULLUP | 0x80) /* FMCA_TDI */
+			DM814X_IOPAD(0x08ac, PIN_INPUT_PULLUP | 0x80) /* FMCA_TRST */
+
+			DM814X_IOPAD(0x08b0, PIN_INPUT_PULLUP | 0x80) /* FMCB_TMS */
+			DM814X_IOPAD(0x0a88, PIN_INPUT_PULLUP | 0x80) /* FMCB_TCK */
+			DM814X_IOPAD(0x0a8c, PIN_INPUT_PULLUP | 0x80) /* FMCB_TDO */
+			DM814X_IOPAD(0x08bc, PIN_INPUT_PULLUP | 0x80) /* FMCB_TDI */
+			DM814X_IOPAD(0x0a94, PIN_INPUT_PULLUP | 0x80) /* FMCB_TRST */
+
+			DM814X_IOPAD(0x08d4, PIN_INPUT_PULLUP | 0x80) /* FPGA_TMS */
+			DM814X_IOPAD(0x0aa8, PIN_INPUT_PULLUP | 0x80) /* FPGA_TCK */
+			DM814X_IOPAD(0x0adc, PIN_INPUT_PULLUP | 0x80) /* FPGA_TDO */
+			DM814X_IOPAD(0x0ab0, PIN_INPUT_PULLUP | 0x80) /* FPGA_TDI */
+			>;
+	};
+
+	gpio2_pins: pinmux_gpio2_pins {
+		pinctrl-single,pins = <
+			DM814X_IOPAD(0x090c, PIN_INPUT_PULLUP | 0x80) /* PHY A IRQ */
+			DM814X_IOPAD(0x0910, PIN_INPUT_PULLUP | 0x80) /* PHY A RESET */
+			DM814X_IOPAD(0x08f4, PIN_INPUT_PULLUP | 0x80) /* PHY B IRQ */
+			DM814X_IOPAD(0x08f8, PIN_INPUT_PULLUP | 0x80) /* PHY B RESET */
+
+			//DM814X_IOPAD(0x0a14, PIN_INPUT_PULLUP | 0x80) /* ARM IRQ */
+			//DM814X_IOPAD(0x0900, PIN_INPUT | 0x80) /* GPIO IRQ */
+			DM814X_IOPAD(0x0a2c, PIN_INPUT_PULLUP | 0x80) /* GPIO RESET */
+		>;
+	};
+
+	gpio4_pins: pinmux_gpio4_pins {
+		pinctrl-single,pins = <
+			/* The PLL doesn't react well to the SPI controller reset, so
+			 * we force the CS lines to pull up as GPIOs until we're ready.
+			 * See https://e2e.ti.com/support/processors/f/791/t/276011?Linux-support-for-AM3874-DM8148-in-Arago-linux-omap3
+			 */
+			DM814X_IOPAD(0x0b3c, PIN_INPUT_PULLUP | 0x80) /* BP_ARM_GPIO0 */
+			DM814X_IOPAD(0x0b40, PIN_INPUT_PULLUP | 0x80) /* BP_ARM_GPIO1 */
+			DM814X_IOPAD(0x0b44, PIN_INPUT_PULLUP | 0x80) /* BP_ARM_GPIO2 */
+			DM814X_IOPAD(0x0b48, PIN_INPUT_PULLUP | 0x80) /* BP_ARM_GPIO3 */
+			DM814X_IOPAD(0x0b4c, PIN_INPUT_PULLUP | 0x80) /* BP_ARM_GPIO4 */
+			DM814X_IOPAD(0x0b50, PIN_INPUT_PULLUP | 0x80) /* BP_ARM_GPIO5 */
+		>;
+	};
+
+	spi2_pins: pinmux_spi2_pins {
+		pinctrl-single,pins = <
+			DM814X_IOPAD(0x0950, PIN_INPUT_PULLUP | 0x80) /* PLL SPI CS1 as GPIO */
+			DM814X_IOPAD(0x0818, PIN_INPUT_PULLUP | 0x80) /* PLL SPI CS2 as GPIO */
+		>;
+	};
+
+	spi4_pins: pinmux_spi4_pins {
+		pinctrl-single,pins = <
+			DM814X_IOPAD(0x0a7c, 0x20)
+			DM814X_IOPAD(0x0b74, 0x20)
+			DM814X_IOPAD(0x0b78, PIN_OUTPUT | 0x20)
+			DM814X_IOPAD(0x0b7c, PIN_OUTPUT_PULLDOWN | 0x20)
+			DM814X_IOPAD(0x0b80, PIN_INPUT | 0x20)
+		>;
+	};
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio1_pins>;
+	gpio-line-names =
+		"", "PROGRAM_B", "INIT_B", "DONE",			/* 0-3 */
+		"", "", "", "",						/* 4-7 */
+		"FMCA_TMS", "FMCA_TCK", "FMCA_TDO", "FMCA_TDI",		/* 8-11 */
+		"", "", "", "FMCA_TRST",				/* 12-15 */
+		"FMCB_TMS", "FMCB_TCK", "FMCB_TDO", "FMCB_TDI",		/* 16-19 */
+		"FMCB_TRST", "", "", "",				/* 20-23 */
+		"FPGA_TMS", "FPGA_TCK", "FPGA_TDO", "FPGA_TDI",		/* 24-27 */
+		"", "", "", "";						/* 28-31 */
+};
+
+&gpio2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio2_pins>;
+	gpio-line-names =
+		"PHYA_IRQ_N", "PHYA_RESET_N", "", "",			/* 0-3 */
+		"", "", "", "PHYB_IRQ_N",				/* 4-7 */
+		"PHYB_RESET_N", "ARM_IRQ", "GPIO_IRQ", "";		/* 8-11 */
+};
+
+&gpio3 {
+	pinctrl-names = "default";
+	/*pinctrl-0 = <&gpio3_pins>;*/
+	gpio-line-names =
+		"", "", "ARMClkSel0", "",				/* 0-3 */
+		"EnFPGARef", "", "", "ARMClkSel1";			/* 4-7 */
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio4_pins>;
+	gpio-line-names =
+		"BP_ARM_GPIO0", "BP_ARM_GPIO1", "BP_ARM_GPIO2", "BP_ARM_GPIO3",
+		"BP_ARM_GPIO4", "BP_ARM_GPIO5";
+};
+
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_pins>;
+	dr_mode = "host";
+};
+
+&usb1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins>;
+	dr_mode = "host";
+};
+
+&mcspi1 {
+	s25fl256@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+
+		fsbl@0 {
+			/* 256 kB */
+			label = "U-Boot-min";
+			reg = <0 0x40000>;
+		};
+		ssbl@1 {
+			/* 512 kB */
+			label = "U-Boot";
+			reg = <0x40000 0x80000>;
+		};
+		bootenv@2 {
+			/* 256 kB */
+			label = "U-Boot Env";
+			reg = <0xc0000 0x40000>;
+		};
+		kernel@3 {
+			/* 4 MB */
+			label = "Kernel";
+			reg = <0x100000 0x400000>;
+		};
+		ipmi@4 {
+			label = "IPMI FRU";
+			reg = <0x500000 0x40000>;
+		};
+		fs@5 {
+			label = "File System";
+			reg = <0x540000 0x1ac0000>;
+		};
+	};
+};
+
+&mcspi3 {
+	/* DMA event numbers stolen from MCASP */
+	dmas = <&edma_xbar 8 0 16 &edma_xbar 9 0 17
+		&edma_xbar 10 0 18 &edma_xbar 11 0 19>;
+	dma-names = "tx0", "rx0", "tx1", "rx1";
+};
+
+&mcspi4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi4_pins>;
+
+	/* DMA event numbers stolen from MCASP, MCBSP */
+	dmas = <&edma_xbar 12 0 20 &edma_xbar 13 0 21>;
+	dma-names = "tx0", "rx0";
+};
--- a/arch/arm/boot/dts/am437x-gp-evm.dts
+++ b/arch/arm/boot/dts/am437x-gp-evm.dts
@ -71,7 +71,7 @@
 		pinctrl-0 = <&matrix_keypad_default>;
 		pinctrl-1 = <&matrix_keypad_sleep>;

-		linux,wakeup;
+		wakeup-source;

 		row-gpios = <&gpio0 3 GPIO_ACTIVE_HIGH /* Bank0, pin3 */
 				&gpio4 3 GPIO_ACTIVE_HIGH /* Bank4, pin3 */
--- a/arch/arm/boot/dts/am437x-l4.dtsi
+++ b/arch/arm/boot/dts/am437x-l4.dtsi
@ -280,12 +280,6 @@
 				#size-cells = <1>;
 				ranges = <0 0 0x4000>;

-				phy_sel: cpsw-phy-sel@650 {
-					compatible = "ti,am43xx-cpsw-phy-sel";
-					reg= <0x650 0x4>;
-					reg-names = "gmii-sel";
-				};
-
 				am43xx_pinmux: pinmux@800 {
 					compatible = "ti,am437-padconf",
 						     "pinctrl-single";
@ -300,11 +294,17 @@
 				};

 				scm_conf: scm_conf@0 {
-					compatible = "syscon";
+					compatible = "syscon", "simple-bus";
 					reg = <0x0 0x800>;
 					#address-cells = <1>;
 					#size-cells = <1>;

+					phy_gmii_sel: phy-gmii-sel {
+						compatible = "ti,am43xx-phy-gmii-sel";
+						reg = <0x650 0x4>;
+						#phy-cells = <2>;
+					};
+
 					scm_clocks: clocks {
 						#address-cells = <1>;
 						#size-cells = <0>;
@ -555,7 +555,6 @@
 				cpts_clock_shift = <29>;
 				ranges = <0 0 0x8000>;
 				syscon = <&scm_conf>;
-				cpsw-phy-sel = <&phy_sel>;

 				davinci_mdio: mdio@1000 {
 					compatible = "ti,am4372-mdio","ti,cpsw-mdio","ti,davinci_mdio";
@ -572,11 +571,13 @@
 				cpsw_emac0: slave@200 {
 					/* Filled in by U-Boot */
 					mac-address = [ 00 00 00 00 00 00 ];
+					phys = <&phy_gmii_sel 1 0>;
 				};

 				cpsw_emac1: slave@300 {
 					/* Filled in by U-Boot */
 					mac-address = [ 00 00 00 00 00 00 ];
+					phys = <&phy_gmii_sel 2 0>;
 				};
 			};
 		};
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/am43x-epos-evm.dts
@ -584,10 +584,7 @@
 &cpsw_emac0 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rmii";
-};
-
-&phy_sel {
-	rmii-clock-ext;
+	phys = <&phy_gmii_sel 1 1>;
 };

 &i2c0 {
--- a/arch/arm/boot/dts/arm-realview-eb.dtsi
+++ b/arch/arm/boot/dts/arm-realview-eb.dtsi
@ -22,9 +22,10 @@

 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
-#include "skeleton.dtsi"

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	compatible = "arm,realview-eb";

 	chosen { };
@ -38,6 +39,7 @@
 	};

 	memory {
+		device_type = "memory";
 		/* 128 MiB memory @ 0x0 */
 		reg = <0x00000000 0x08000000>;
 	};
--- a/arch/arm/boot/dts/arm-realview-pb1176.dts
+++ b/arch/arm/boot/dts/arm-realview-pb1176.dts
@ -23,9 +23,10 @@
 /dts-v1/;
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
-#include "skeleton.dtsi"

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	model = "ARM RealView PB1176";
 	compatible = "arm,realview-pb1176";

@ -40,6 +41,7 @@
 	};

 	memory {
+		device_type = "memory";
 		/* 128 MiB memory @ 0x0 */
 		reg = <0x00000000 0x08000000>;
 	};
--- a/arch/arm/boot/dts/arm-realview-pb11mp.dts
+++ b/arch/arm/boot/dts/arm-realview-pb11mp.dts
@ -23,9 +23,10 @@
 /dts-v1/;
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
-#include "skeleton.dtsi"

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	model = "ARM RealView PB11MPcore";
 	compatible = "arm,realview-pb11mp";

@ -39,6 +40,7 @@
 	};

 	memory {
+		device_type = "memory";
 		/*
 		 * The PB11MPCore has 512 MiB memory @ 0x70000000
 		 * and the first 256 are also remapped @ 0x00000000
--- a/arch/arm/boot/dts/arm-realview-pbx.dtsi
+++ b/arch/arm/boot/dts/arm-realview-pbx.dtsi
@ -22,9 +22,10 @@

 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
-#include "skeleton.dtsi"

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	compatible = "arm,realview-pbx";

 	chosen { };
@ -39,6 +40,7 @@
 	};

 	memory {
+		device_type = "memory";
 		/* 128 MiB memory @ 0x0 */
 		reg = <0x00000000 0x08000000>;
 	};
--- a/arch/arm/boot/dts/armada-370-rd.dts
+++ b/arch/arm/boot/dts/armada-370-rd.dts
@ -114,48 +114,6 @@
 			};
 		};
 	};
-
-	dsa {
-		status = "disabled";
-
-		compatible = "marvell,dsa";
-		#address-cells = <2>;
-		#size-cells = <0>;
-
-		dsa,ethernet = <&eth1>;
-		dsa,mii-bus = <&mdio>;
-
-		switch@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x10 0>;	/* MDIO address 16, switch 0 in tree */
-
-			port@0 {
-				reg = <0>;
-				label = "lan0";
-			};
-
-			port@1 {
-			       reg = <1>;
-			       label = "lan1";
-			};
-
-			port@2 {
-			       reg = <2>;
-			       label = "lan2";
-			};
-
-			port@3 {
-			       reg = <3>;
-			       label = "lan3";
-			};
-
-			port@5 {
-			      reg = <5>;
-			      label = "cpu";
-			};
-		};
-	 };
 };

 &pciec {
--- a/arch/arm/boot/dts/armada-388-clearfog.dts
+++ b/arch/arm/boot/dts/armada-388-clearfog.dts
@ -30,64 +30,6 @@
 		};
 	};

-	dsa@0 {
-		status = "disabled";
-
-		compatible = "marvell,dsa";
-		dsa,ethernet = <&eth1>;
-		dsa,mii-bus = <&mdio>;
-		pinctrl-0 = <&clearfog_dsa0_clk_pins &clearfog_dsa0_pins>;
-		pinctrl-names = "default";
-		#address-cells = <2>;
-		#size-cells = <0>;
-
-		switch@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4 0>;
-
-			port@0 {
-				reg = <0>;
-				label = "lan5";
-			};
-
-			port@1 {
-				reg = <1>;
-				label = "lan4";
-			};
-
-			port@2 {
-				reg = <2>;
-				label = "lan3";
-			};
-
-			port@3 {
-				reg = <3>;
-				label = "lan2";
-			};
-
-			port@4 {
-				reg = <4>;
-				label = "lan1";
-			};
-
-			port@5 {
-				reg = <5>;
-				label = "cpu";
-			};
-
-			port@6 {
-				/* 88E1512 external phy */
-				reg = <6>;
-				label = "lan6";
-				fixed-link {
-					speed = <1000>;
-					full-duplex;
-				};
-			};
-		};
-	};
-
 	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-0 = <&rear_button_pins>;
--- a/arch/arm/boot/dts/armada-38x.dtsi
+++ b/arch/arm/boot/dts/armada-38x.dtsi
@ -9,13 +9,15 @@
 * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 */

-#include "skeleton.dtsi"
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>

 #define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	model = "Marvell Armada 38x family SoC";
 	compatible = "marvell,armada380";

--- a/arch/arm/boot/dts/armada-39x.dtsi
+++ b/arch/arm/boot/dts/armada-39x.dtsi
@ -7,13 +7,14 @@
 * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 */

-#include "skeleton.dtsi"
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>

 #define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	model = "Marvell Armada 39x family SoC";
 	compatible = "marvell,armada390";

--- a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
+++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
@ -210,53 +210,6 @@
 		compatible = "pwm-fan";
 		pwms = <&gpio0 24 4000>;
 	};
-
-	dsa {
-		status = "disabled";
-
-		compatible = "marvell,dsa";
-		#address-cells = <2>;
-		#size-cells = <0>;
-
-		dsa,ethernet = <&eth0>;
-		dsa,mii-bus = <&mdio>;
-
-		switch@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x0 0>;	/* MDIO address 0, switch 0 in tree */
-
-			port@0 {
-				reg = <0>;
-				label = "lan4";
-			};
-
-			port@1 {
-				reg = <1>;
-				label = "lan3";
-			};
-
-			port@2 {
-				reg = <2>;
-				label = "lan2";
-			};
-
-			port@3 {
-				reg = <3>;
-				label = "lan1";
-			};
-
-			port@4 {
-				reg = <4>;
-				label = "internet";
-			};
-
-			port@5 {
-				reg = <5>;
-				label = "cpu";
-			};
-		};
-	};
 };

 &pciec {
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@ -43,9 +43,10 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/dma/nbpfaxi.h>
 #include <dt-bindings/clock/axis,artpec6-clkctrl.h>
-#include "skeleton.dtsi"

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	compatible = "axis,artpec6";
 	interrupt-parent = <&intc>;

--- a/arch/arm/boot/dts/aspeed-bmc-arm-stardragon4800-rep2.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-arm-stardragon4800-rep2.dts
@ -173,6 +173,16 @@
 			};
 		};
 	};
+
+	dps650ab@58 {
+		compatible = "delta,dps650ab";
+		reg = <0x58>;
+	};
+
+	dps650ab@59 {
+		compatible = "delta,dps650ab";
+		reg = <0x59>;
+	};
 };

 &i2c9 {
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts
@ -21,6 +21,17 @@
 	memory@80000000 {
 		reg = <0x80000000 0x20000000>;
 	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+					<&adc 4>, <&adc 5>, <&adc 6>;
+	};
+
+	iio-hwmon-battery {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 7>;
+	};
 };

 &fmc {
@ -43,6 +54,16 @@
 	};
 };

+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&lpc_ctrl {
+	// Enable lpc clock
+	status = "okay";
+};
+
 &uart1 {
 	// Host Console
 	status = "okay";
@ -51,11 +72,33 @@
 		     &pinctrl_rxd1_default>;
 };

+&uart2 {
+	// SoL Host Console
+	status = "okay";
+};
+
+&uart3 {
+	// SoL BMC Console
+	status = "okay";
+};
+
 &uart5 {
 	// BMC Console
 	status = "okay";
 };

+&kcs2 {
+	// BMC KCS channel 2
+	status = "okay";
+	kcs_addr = <0xca8>;
+};
+
+&kcs3 {
+	// BMC KCS channel 3
+	status = "okay";
+	kcs_addr = <0xca2>;
+};
+
 &mac0 {
 	status = "okay";

@ -64,6 +107,10 @@
 	use-ncsi;
 };

+&adc {
+	status = "okay";
+};
+
 &i2c0 {
 	status = "okay";
 	//Airmax Conn B, CPU0 PIROM, CPU1 PIROM
@ -122,6 +169,10 @@

 &i2c8 {
 	status = "okay";
+	tmp421@1f {
+		compatible = "ti,tmp421";
+		reg = <0x1f>;
+	};
 	//Mezz Sensor SMBus
 };

@ -140,7 +191,7 @@
 	};

 	fan@1 {
-		reg = <0x00>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
 	};
 };
--- a/arch/arm/boot/dts/aspeed-bmc-inspur-on5263m5.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-inspur-on5263m5.dts
@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018 Inspur Corporation
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "ON5263M5 BMC";
+	compatible = "inspur,on5263m5-bmc", "aspeed,ast2500";
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "earlyprintk";
+	};
+
+	memory {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		vga_memory: framebuffer@9f000000 {
+			no-map;
+			reg = <0x9f000000 0x01000000>;
+		};
+	};
+
+	leds {
+	    compatible = "gpio-leds";
+	    bmc_alive {
+		label = "bmc_alive";
+		gpios = <&gpio ASPEED_GPIO(I, 1) GPIO_ACTIVE_LOW>;
+		linux,default-trigger = "timer";
+	    };
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>;
+	};
+
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+	};
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&mac0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii1_default>;
+	use-ncsi;
+};
+
+&mac1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&i2c6 {
+	status = "okay";
+
+	tmp421@4e {
+		compatible = "ti,tmp421";
+		reg = <0x4e>;
+	};
+
+	tmp112@48 {
+		compatible = "ti,tmp112";
+		reg = <0x48>;
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+		pagesize = <32>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	adm1278@11 {
+		  compatible = "adi,adm1278";
+		  reg = <0x11>;
+	};
+};
+
+&gfx {
+	status = "okay";
+};
+
+&pinctrl {
+	aspeed,external-nodes = <&gfx &lhc>;
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00 0x01>;
+	};
+
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02 0x03>;
+	};
+};
+
+&adc {
+	status = "okay";
+};
--- a/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts
@ -169,6 +169,11 @@

 &i2c3 {
 	status = "okay";
+
+	occ-hwmon@50 {
+		compatible = "ibm,p8-occ-hwmon";
+		reg = <0x50>;
+	};
 };

 &i2c4 {
--- a/arch/arm/boot/dts/aspeed-bmc-quanta-q71l.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-quanta-q71l.dts
@ -116,6 +116,10 @@
 	status = "okay";
 };

+&lpc_ctrl {
+	status = "okay";
+};
+
 &lpc_snoop {
 	status = "okay";
 	snoop-ports = <0x80>;
@ -134,6 +138,10 @@
 	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
 };

+&uart1 {
+	status = "okay";
+};
+
 &uart5 {
 	status = "okay";
 };
--- a/arch/arm/boot/dts/aspeed-g4.dtsi
+++ b/arch/arm/boot/dts/aspeed-g4.dtsi
@ -197,6 +197,7 @@
 				gpio-ranges = <&pinctrl 0 0 220>;
 				clocks = <&syscon ASPEED_CLK_APB>;
 				interrupt-controller;
+				#interrupt-cells = <2>;
 			};

 			timer: timer@1e782000 {
--- a/arch/arm/boot/dts/aspeed-g5.dtsi
+++ b/arch/arm/boot/dts/aspeed-g5.dtsi
@ -250,6 +250,7 @@
 				gpio-ranges = <&pinctrl 0 0 220>;
 				clocks = <&syscon ASPEED_CLK_APB>;
 				interrupt-controller;
+				#interrupt-cells = <2>;
 			};

 			timer: timer@1e782000 {
@ -330,8 +331,32 @@
 				ranges = <0x0 0x1e789000 0x1000>;

 				lpc_bmc: lpc-bmc@0 {
-					compatible = "aspeed,ast2500-lpc-bmc";
+					compatible = "aspeed,ast2500-lpc-bmc", "simple-mfd", "syscon";
 					reg = <0x0 0x80>;
+					reg-io-width = <4>;
+
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0x0 0x0 0x80>;
+
+					kcs1: kcs1@0 {
+						compatible = "aspeed,ast2500-kcs-bmc";
+						interrupts = <8>;
+						kcs_chan = <1>;
+						status = "disabled";
+					};
+					kcs2: kcs2@0 {
+						compatible = "aspeed,ast2500-kcs-bmc";
+						interrupts = <8>;
+						kcs_chan = <2>;
+						status = "disabled";
+					};
+					kcs3: kcs3@0 {
+						compatible = "aspeed,ast2500-kcs-bmc";
+						interrupts = <8>;
+						kcs_chan = <3>;
+						status = "disabled";
+					};
 				};

 				lpc_host: lpc-host@80 {
@ -343,6 +368,13 @@
 					#size-cells = <1>;
 					ranges = <0x0 0x80 0x1e0>;

+					kcs4: kcs4@0 {
+						compatible = "aspeed,ast2500-kcs-bmc";
+						interrupts = <8>;
+						kcs_chan = <4>;
+						status = "disabled";
+					};
+
 					lpc_ctrl: lpc-ctrl@0 {
 						compatible = "aspeed,ast2500-lpc-ctrl";
 						reg = <0x0 0x80>;
--- a/arch/arm/boot/dts/at91-nattis-2-natte-2.dts
+++ b/arch/arm/boot/dts/at91-nattis-2-natte-2.dts
@ -22,7 +22,7 @@
 		wakeup {
 			label = "Wakeup";
 			linux,code = <10>;
-			gpio-key,wakeup;
+			wakeup-source;
 			gpios = <&pioB 27 GPIO_ACTIVE_LOW>;
 		};
 	};
--- a/arch/arm/boot/dts/at91-sama5d27_som1.dtsi
+++ b/arch/arm/boot/dts/at91-sama5d27_som1.dtsi
@ -62,6 +62,20 @@

 	ahb {
 		apb {
+			qspi1: spi@f0024000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_qspi1_default>;
+
+				flash@0 {
+					compatible = "jedec,spi-nor";
+					reg = <0>;
+					spi-max-frequency = <80000000>;
+					spi-tx-bus-width = <4>;
+					spi-rx-bus-width = <4>;
+					m25p,fast-read;
+				};
+			};
+
 			macb0: ethernet@f8008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_macb0_default>;
@ -78,6 +92,22 @@

 			pinctrl@fc038000 {

+				pinctrl_qspi1_default: qspi1_default {
+					sck_cs {
+						pinmux = <PIN_PB5__QSPI1_SCK>,
+							 <PIN_PB6__QSPI1_CS>;
+						bias-disable;
+					};
+
+					data {
+						pinmux = <PIN_PB7__QSPI1_IO0>,
+							 <PIN_PB8__QSPI1_IO1>,
+							 <PIN_PB9__QSPI1_IO2>,
+							 <PIN_PB10__QSPI1_IO3>;
+						bias-pull-up;
+					};
+				};
+
 				pinctrl_macb0_default: macb0_default {
 					pinmux = <PIN_PD9__GTXCK>,
 						 <PIN_PD10__GTXEN>,
--- a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
@ -109,6 +109,10 @@
 				status = "okay";
 			};

+			qspi1: spi@f0024000 {
+				status = "okay";
+			};
+
 			spi0: spi@f8000000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_spi0_default>;
--- a/arch/arm/boot/dts/at91-wb45n.dts
+++ b/arch/arm/boot/dts/at91-wb45n.dts
@ -22,7 +22,7 @@
 			label = "IRQBTN";
 			linux,code = <99>;
 			gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
-			gpio-key,wakeup = <1>;
+			wakeup-source;
 		};
 	};
 };
--- a/arch/arm/boot/dts/at91-wb50n.dts
+++ b/arch/arm/boot/dts/at91-wb50n.dts
@ -23,7 +23,7 @@
 			label = "BTNESC";
 			linux,code = <1>; /* ESC button */
 			gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
-			gpio-key,wakeup = <1>;
+			wakeup-source;
 		};

 		irqbtn@31 {
@ -31,7 +31,7 @@
 			label = "IRQBTN";
 			linux,code = <99>; /* SysReq button */
 			gpios = <&pioE 31 GPIO_ACTIVE_LOW>;
-			gpio-key,wakeup = <1>;
+			wakeup-source;
 		};
 	};

--- a/arch/arm/boot/dts/at91rm9200.dtsi
+++ b/arch/arm/boot/dts/at91rm9200.dtsi
@ -10,13 +10,14 @@
 * Licensed under GPLv2 or later.
 */

-#include "skeleton.dtsi"
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	model = "Atmel AT91RM9200 family SoC";
 	compatible = "atmel,at91rm9200";
 	interrupt-parent = <&aic>;
@ -49,6 +50,7 @@
 	};

 	memory {
+		device_type = "memory";
 		reg = <0x20000000 0x04000000>;
 	};

--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@ -8,13 +8,14 @@
 * Licensed under GPLv2 or later.
 */

-#include "skeleton.dtsi"
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	model = "Atmel AT91SAM9260 family SoC";
 	compatible = "atmel,at91sam9260";
 	interrupt-parent = <&aic>;
@ -46,6 +47,7 @@
 	};

 	memory {
+		device_type = "memory";
 		reg = <0x20000000 0x04000000>;
 	};

--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/at91sam9261.dtsi
@ -6,13 +6,14 @@
 * Licensed under GPLv2 only.
 */

-#include "skeleton.dtsi"
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	model = "Atmel AT91SAM9261 family SoC";
 	compatible = "atmel,at91sam9261";
 	interrupt-parent = <&aic>;
@ -43,6 +44,7 @@
 	};

 	memory {
+		device_type = "memory";
 		reg = <0x20000000 0x08000000>;
 	};

--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/at91sam9263.dtsi
@ -6,13 +6,14 @@
 * Licensed under GPLv2 only.
 */

-#include "skeleton.dtsi"
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	model = "Atmel AT91SAM9263 family SoC";
 	compatible = "atmel,at91sam9263";
 	interrupt-parent = <&aic>;
@ -45,6 +46,7 @@
 	};

 	memory {
+		device_type = "memory";
 		reg = <0x20000000 0x08000000>;
 	};

--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@ -9,7 +9,6 @@
 * Licensed under GPLv2 or later.
 */

-#include "skeleton.dtsi"
 #include <dt-bindings/dma/at91.h>
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
@ -17,6 +16,8 @@
 #include <dt-bindings/clock/at91.h>

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	model = "Atmel AT91SAM9G45 family SoC";
 	compatible = "atmel,at91sam9g45";
 	interrupt-parent = <&aic>;
@ -51,6 +52,7 @@
 	};

 	memory {
+		device_type = "memory";
 		reg = <0x70000000 0x10000000>;
 	};

--- a/arch/arm/boot/dts/at91sam9n12.dtsi
+++ b/arch/arm/boot/dts/at91sam9n12.dtsi
@ -7,7 +7,6 @@
 * Licensed under GPLv2 or later.
 */

-#include "skeleton.dtsi"
 #include <dt-bindings/dma/at91.h>
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
@ -15,6 +14,8 @@
 #include <dt-bindings/clock/at91.h>

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	model = "Atmel AT91SAM9N12 SoC";
 	compatible = "atmel,at91sam9n12";
 	interrupt-parent = <&aic>;
@ -47,6 +48,7 @@
 	};

 	memory {
+		device_type = "memory";
 		reg = <0x20000000 0x10000000>;
 	};

--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/at91sam9rl.dtsi
@ -7,7 +7,6 @@
 * Licensed under GPLv2 or later.
 */

-#include "skeleton.dtsi"
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/clock/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
@ -15,6 +14,8 @@
 #include <dt-bindings/pwm/pwm.h>

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	model = "Atmel AT91SAM9RL family SoC";
 	compatible = "atmel,at91sam9rl", "atmel,at91sam9";
 	interrupt-parent = <&aic>;
@ -48,6 +49,7 @@
 	};

 	memory {
+		device_type = "memory";
 		reg = <0x20000000 0x04000000>;
 	};

--- a/arch/arm/boot/dts/at91sam9x5.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5.dtsi
@ -9,7 +9,6 @@
 * Licensed under GPLv2 or later.
 */

-#include "skeleton.dtsi"
 #include <dt-bindings/dma/at91.h>
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
@ -17,6 +16,8 @@
 #include <dt-bindings/clock/at91.h>

 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	model = "Atmel AT91SAM9x5 family SoC";
 	compatible = "atmel,at91sam9x5";
 	interrupt-parent = <&aic>;
@ -49,6 +50,7 @@
 	};

 	memory {
+		device_type = "memory";
 		reg = <0x20000000 0x10000000>;
 	};

--- a/arch/arm/boot/dts/atlas6-evb.dts
+++ b/arch/arm/boot/dts/atlas6-evb.dts
@ -15,6 +15,7 @@
 	compatible = "sirf,atlas6-cb", "sirf,atlas6";

 	memory {
+		device_type = "memory";
 		reg = <0x00000000 0x20000000>;
 	};

--- a/arch/arm/boot/dts/atlas6.dtsi
+++ b/arch/arm/boot/dts/atlas6.dtsi
@ -6,7 +6,6 @@
 * Licensed under GPLv2 or later.
 */

-/include/ "skeleton.dtsi"
 / {
 	compatible = "sirf,atlas6";
 	#address-cells = <1>;
--- a/arch/arm/boot/dts/atlas7.dtsi
+++ b/arch/arm/boot/dts/atlas7.dtsi
@ -6,7 +6,6 @@
 * Licensed under GPLv2 or later.
 */

-/include/ "skeleton.dtsi"
 / {
 	compatible = "sirf,atlas7";
 	#address-cells = <1>;
--- a/arch/arm/boot/dts/axm55xx.dtsi
+++ b/arch/arm/boot/dts/axm55xx.dtsi
@ -12,9 +12,9 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/lsi,axm5516-clks.h>

-#include "skeleton64.dtsi"
-
 / {
+	#address-cells = <2>;
+	#size-cells = <2>;
 	interrupt-parent = <&gic>;

 	aliases {
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@ -34,9 +34,9 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/clock/bcm-cygnus.h>

-#include "skeleton.dtsi"
-
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	compatible = "brcm,cygnus";
 	model = "Broadcom Cygnus SoC";
 	interrupt-parent = <&gic>;
@ -45,6 +45,11 @@
 		ethernet0 = &eth0;
 	};

+	memory {
+		device_type = "memory";
+		reg = <0 0>;
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
--- a/arch/arm/boot/dts/bcm-nsp.dtsi
+++ b/arch/arm/boot/dts/bcm-nsp.dtsi
@ -34,9 +34,9 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/clock/bcm-nsp.h>

-#include "skeleton.dtsi"
-
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	compatible = "brcm,nsp";
 	model = "Broadcom Northstar Plus SoC";
 	interrupt-parent = <&gic>;
--- a/arch/arm/boot/dts/bcm11351.dtsi
+++ b/arch/arm/boot/dts/bcm11351.dtsi
@ -16,9 +16,9 @@

 #include "dt-bindings/clock/bcm281xx.h"

-#include "skeleton.dtsi"
-
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	model = "BCM11351 SoC";
 	compatible = "brcm,bcm11351";
 	interrupt-parent = <&gic>;
--- a/arch/arm/boot/dts/bcm21664-garnet.dts
+++ b/arch/arm/boot/dts/bcm21664-garnet.dts
@ -22,6 +22,7 @@
 	compatible = "brcm,bcm21664-garnet", "brcm,bcm21664";

 	memory {
+		device_type = "memory";
 		reg = <0x80000000 0x40000000>; /* 1 GB */
 	};

--- a/arch/arm/boot/dts/bcm21664.dtsi
+++ b/arch/arm/boot/dts/bcm21664.dtsi
@ -16,9 +16,9 @@

 #include "dt-bindings/clock/bcm21664.h"

-#include "skeleton.dtsi"
-
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	model = "BCM21664 SoC";
 	compatible = "brcm,bcm21664";
 	interrupt-parent = <&gic>;
--- a/arch/arm/boot/dts/bcm23550-sparrow.dts
+++ b/arch/arm/boot/dts/bcm23550-sparrow.dts
@ -46,6 +46,7 @@
 	};

 	memory {
+		device_type = "memory";
 		reg = <0x80000000 0x20000000>; /* 512 MB */
 	};
 };
--- a/arch/arm/boot/dts/bcm23550.dtsi
+++ b/arch/arm/boot/dts/bcm23550.dtsi
@ -36,9 +36,9 @@
 /* BCM23550 and BCM21664 have almost identical clocks */
 #include "dt-bindings/clock/bcm21664.h"

-#include "skeleton.dtsi"
-
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
 	model = "BCM23550 SoC";
 	compatible = "brcm,bcm23550";
 	interrupt-parent = <&gic>;
--- a/arch/arm/boot/dts/bcm28155-ap.dts
+++ b/arch/arm/boot/dts/bcm28155-ap.dts
@ -22,6 +22,7 @@
 	compatible = "brcm,bcm28155-ap", "brcm,bcm11351";

 	memory {
+		device_type = "memory";
 		reg = <0x80000000 0x40000000>; /* 1 GB */
 	};

--- a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
@ -31,8 +31,8 @@
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
-	gpio-line-names = "SDA0",
-			  "SCL0",
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
 			  "SDA1",
 			  "SCL1",
 			  "GPIO_GCLK",
--- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
@ -33,8 +33,8 @@
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
-	gpio-line-names = "SDA0",
-			  "SCL0",
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
 			  "SDA1",
 			  "SCL1",
 			  "GPIO_GCLK",
--- a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
@ -25,8 +25,6 @@

 	wifi_pwrseq: wifi-pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
-		pinctrl-0 = <&wl_on>;
 		reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
 	};
 };
@ -40,8 +38,8 @@
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
-	gpio-line-names = "GPIO0",
-			  "GPIO1",
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
 			  "SDA1",
 			  "SCL1",
 			  "GPIO_GCLK",
@ -98,11 +96,6 @@
 			  "SD_DATA3_R";

 	pinctrl-0 = <&gpioout &alt0>;
-
-	wl_on: wl-on {
-		brcm,pins = <41>;
-		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
-	};
 };

 &hdmi {
--- a/arch/arm/boot/dts/bcm2835-rpi-zero.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-zero.dts
@ -28,8 +28,8 @@
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
-	gpio-line-names = "SDA0",
-			  "SCL0",
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
 			  "SDA1",
 			  "SCL1",
 			  "GPIO_GCLK",
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@ -1,7 +1,7 @@
 #include <dt-bindings/power/raspberrypi-power.h>

 / {
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0 0x10000000>;
 	};
@ -19,8 +19,6 @@
 	soc {
 		firmware: firmware {
 			compatible = "raspberrypi,bcm2835-firmware", "simple-bus";
-			#address-cells = <0>;
-			#size-cells = <0>;
 			mboxes = <&mailbox>;
 		};

--- a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
+++ b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
@ -9,7 +9,7 @@
 	compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
 	model = "Raspberry Pi 2 Model B";

-	memory {
+	memory@0 {
 		reg = <0 0x40000000>;
 	};

@ -28,6 +28,72 @@
 };

 &gpio {
+	/*
+	 * Taken from rpi_SCH_2b_1p2_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "", /* GPIO30 */
+			  "LAN_RUN",
+			  "CAM_GPIO1",
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "PWR_LOW_N",
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "USB_LIMIT",
+			  "", /* GPIO39 */
+			  "PWM0_OUT",
+			  "CAM_GPIO0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  "ETHCLK",
+			  "PWM1_OUT",
+			  "HDMI_HPD_N",
+			  "STATUS_LED",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;

 	/* I2S interface */
--- a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
@ -0,0 +1,175 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-model-a-plus", "brcm,bcm2837";
+	model = "Raspberry Pi 3 Model A+";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory@0 {
+		reg = <0 0x20000000>;
+	};
+
+	leds {
+		act {
+			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+		};
+
+		pwr {
+			label = "PWR";
+			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "",
+				  "BT_WL_ON",
+				  "STATUS_LED_R",
+				  "",
+				  "",
+				  "CAM_GPIO0",
+				  "CAM_GPIO1",
+				  "";
+		status = "okay";
+	};
+};
+
+&gpio {
+	/*
+	 * This is mostly based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "HDMI_HPD_N",
+			  "STATUS_LED_G",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  "PWM0_OUT",
+			  "PWM1_OUT",
+			  "", /* GPIO42 */
+			  "WIFI_CLK",
+			  "SDA0",
+			  "SCL0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+	status = "okay";
+};
+
+/*
+ * SDHCI is used to control the SDIO for wireless
+ *
+ * WL_REG_ON and BT_REG_ON of the CYW43455 Wifi/BT module are driven
+ * by a single GPIO. We can't give GPIO control to one of the drivers,
+ * otherwise the other part would get unexpectedly disturbed.
+ */
+&sdhci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34>;
+	status = "okay";
+	bus-width = <4>;
+	non-removable;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	status = "okay";
+	bus-width = <4>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <2000000>;
+	};
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
@ -14,7 +14,7 @@
 		stdout-path = "serial1:115200n8";
 	};

-	memory {
+	memory@0 {
 		reg = <0 0x40000000>;
 	};

@ -42,7 +42,7 @@
 		#gpio-cells = <2>;
 		gpio-line-names = "BT_ON",
 				  "WL_ON",
-				  "STATUS_LED",
+				  "STATUS_LED_R",
 				  "LAN_RUN",
 				  "",
 				  "CAM_GPIO0",
@ -52,6 +52,76 @@
 	};
 };

+&gpio {
+	/*
+	 * Taken from rpi_SCH_3bplus_1p0_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "HDMI_HPD_N",
+			  "STATUS_LED_G",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  "PWM0_OUT",
+			  "PWM1_OUT",
+			  "ETHCLK",
+			  "WIFI_CLK",
+			  "SDA0",
+			  "SCL0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+};
+
 &hdmi {
 	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
 };
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
@ -14,7 +14,7 @@
 		stdout-path = "serial1:115200n8";
 	};

-	memory {
+	memory@0 {
 		reg = <0 0x40000000>;
 	};

@ -39,7 +39,7 @@
 				  "WL_ON",
 				  "STATUS_LED",
 				  "LAN_RUN",
-				  "HPD_N",
+				  "HDMI_HPD_N",
 				  "CAM_GPIO0",
 				  "CAM_GPIO1",
 				  "PWR_LOW_N";
@ -47,6 +47,76 @@
 	};
 };

+&gpio {
+	/*
+	 * Taken from rpi_SCH_3b_1p2_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "", /* GPIO 28 */
+			  "LAN_RUN_BOOT",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  "PWM0_OUT",
+			  "PWM1_OUT",
+			  "ETHCLK",
+			  "WIFI_CLK",
+			  "SDA0",
+			  "SCL0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
--- a/Показать больше
+++ b/Показать больше