pinctrl: Device tree bindings for Qualcomm PMIC MPP block
DeviceTree binding documentation for Qualcomm SPMI PMIC MPP pinctrl drivers. Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com> Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit is contained in:
Ivan T. Ivanov
Linus Walleij
Родитель
43059f6ba2
Коммит
89a7117d56
|
|
@ -0,0 +1,162 @@
|
|||
Qualcomm PMIC Multi-Purpose Pin (MPP) block
|
||||
|
||||
This binding describes the MPP block(s) found in the 8xxx series
|
||||
of PMIC's from Qualcomm.
|
||||
|
||||
- compatible:
|
||||
Usage: required
|
||||
Value type: <string>
|
||||
Definition: Should contain one of:
|
||||
"qcom,pm8841-mpp",
|
||||
"qcom,pm8941-mpp",
|
||||
"qcom,pma8084-mpp",
|
||||
|
||||
- reg:
|
||||
Usage: required
|
||||
Value type: <prop-encoded-array>
|
||||
Definition: Register base of the MPP block and length.
|
||||
|
||||
- interrupts:
|
||||
Usage: required
|
||||
Value type: <prop-encoded-array>
|
||||
Definition: Must contain an array of encoded interrupt specifiers for
|
||||
each available MPP
|
||||
|
||||
- gpio-controller:
|
||||
Usage: required
|
||||
Value type: <none>
|
||||
Definition: Mark the device node as a GPIO controller
|
||||
|
||||
- #gpio-cells:
|
||||
Usage: required
|
||||
Value type: <u32>
|
||||
Definition: Must be 2;
|
||||
the first cell will be used to define MPP number and the
|
||||
second denotes the flags for this MPP
|
||||
|
||||
Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
|
||||
a general description of GPIO and interrupt bindings.
|
||||
|
||||
Please refer to pinctrl-bindings.txt in this directory for details of the
|
||||
common pinctrl bindings used by client devices, including the meaning of the
|
||||
phrase "pin configuration node".
|
||||
|
||||
The pin configuration nodes act as a container for an arbitrary number of
|
||||
subnodes. Each of these subnodes represents some desired configuration for a
|
||||
pin or a list of pins. This configuration can include the
|
||||
mux function to select on those pin(s), and various pin configuration
|
||||
parameters, as listed below.
|
||||
|
||||
SUBNODES:
|
||||
|
||||
The name of each subnode is not important; all subnodes should be enumerated
|
||||
and processed purely based on their content.
|
||||
|
||||
Each subnode only affects those parameters that are explicitly listed. In
|
||||
other words, a subnode that lists a mux function but no pin configuration
|
||||
parameters implies no information about any pin configuration parameters.
|
||||
Similarly, a pin subnode that describes a pullup parameter implies no
|
||||
information about e.g. the mux function.
|
||||
|
||||
The following generic properties as defined in pinctrl-bindings.txt are valid
|
||||
to specify in a pin configuration subnode:
|
||||
|
||||
- pins:
|
||||
Usage: required
|
||||
Value type: <string-array>
|
||||
Definition: List of MPP pins affected by the properties specified in
|
||||
this subnode. Valid pins are:
|
||||
mpp1-mpp4 for pm8841
|
||||
mpp1-mpp8 for pm8941
|
||||
mpp1-mpp4 for pma8084
|
||||
|
||||
- function:
|
||||
Usage: required
|
||||
Value type: <string>
|
||||
Definition: Specify the alternative function to be configured for the
|
||||
specified pins. Valid values are:
|
||||
"normal",
|
||||
"paired",
|
||||
"dtest1",
|
||||
"dtest2",
|
||||
"dtest3",
|
||||
"dtest4"
|
||||
|
||||
- bias-disable:
|
||||
Usage: optional
|
||||
Value type: <none>
|
||||
Definition: The specified pins should be configured as no pull.
|
||||
|
||||
- bias-pull-up:
|
||||
Usage: optional
|
||||
Value type: <u32>
|
||||
Definition: The specified pins should be configured as pull up.
|
||||
Valid values are 600, 10000 and 30000 in bidirectional mode
|
||||
only, i.e. when operating in qcom,analog-mode and input and
|
||||
outputs are enabled. The hardware ignores the configuration
|
||||
when operating in other modes.
|
||||
|
||||
- bias-high-impedance:
|
||||
Usage: optional
|
||||
Value type: <none>
|
||||
Definition: The specified pins will put in high-Z mode and disabled.
|
||||
|
||||
- input-enable:
|
||||
Usage: optional
|
||||
Value type: <none>
|
||||
Definition: The specified pins are put in input mode, i.e. their input
|
||||
buffer is enabled
|
||||
|
||||
- output-high:
|
||||
Usage: optional
|
||||
Value type: <none>
|
||||
Definition: The specified pins are configured in output mode, driven
|
||||
high.
|
||||
|
||||
- output-low:
|
||||
Usage: optional
|
||||
Value type: <none>
|
||||
Definition: The specified pins are configured in output mode, driven
|
||||
low.
|
||||
|
||||
- power-source:
|
||||
Usage: optional
|
||||
Value type: <u32>
|
||||
Definition: Selects the power source for the specified pins. Valid power
|
||||
sources are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
|
||||
|
||||
- qcom,analog-mode:
|
||||
Usage: optional
|
||||
Value type: <none>
|
||||
Definition: Selects Analog mode of operation: combined with input-enable
|
||||
and/or output-high, output-low MPP could operate as
|
||||
Bidirectional Logic, Analog Input, Analog Output.
|
||||
|
||||
- qcom,amux-route:
|
||||
Usage: optional
|
||||
Value type: <u32>
|
||||
Definition: Selects the source for analog input. Valid values are
|
||||
defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
|
||||
PMIC_MPP_AMUX_ROUTE_CH5, PMIC_MPP_AMUX_ROUTE_CH6...
|
||||
|
||||
Example:
|
||||
|
||||
mpps@a000 {
|
||||
compatible = "qcom,pm8841-mpp";
|
||||
reg = <0xa000>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupts = <4 0xa0 0 0>, <4 0xa1 0 0>, <4 0xa2 0 0>, <4 0xa3 0 0>;
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pm8841_default>;
|
||||
|
||||
pm8841_default: default {
|
||||
gpio {
|
||||
pins = "mpp1", "mpp2", "mpp3", "mpp4";
|
||||
function = "normal";
|
||||
input-enable;
|
||||
power-source = <PM8841_MPP_S3>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
@ -0,0 +1,44 @@
|
|||
/*
|
||||
* This header provides constants for the Qualcomm PMIC's
|
||||
* Multi-Purpose Pin binding.
|
||||
*/
|
||||
|
||||
#ifndef _DT_BINDINGS_PINCTRL_QCOM_PMIC_MPP_H
|
||||
#define _DT_BINDINGS_PINCTRL_QCOM_PMIC_MPP_H
|
||||
|
||||
/* power-source */
|
||||
#define PM8841_MPP_VPH 0
|
||||
#define PM8841_MPP_S3 2
|
||||
|
||||
#define PM8941_MPP_VPH 0
|
||||
#define PM8941_MPP_L1 1
|
||||
#define PM8941_MPP_S3 2
|
||||
#define PM8941_MPP_L6 3
|
||||
|
||||
#define PMA8084_MPP_VPH 0
|
||||
#define PMA8084_MPP_L1 1
|
||||
#define PMA8084_MPP_S4 2
|
||||
#define PMA8084_MPP_L6 3
|
||||
|
||||
/*
|
||||
* Analog Input - Set the source for analog input.
|
||||
* To be used with "qcom,amux-route" property
|
||||
*/
|
||||
#define PMIC_MPP_AMUX_ROUTE_CH5 0
|
||||
#define PMIC_MPP_AMUX_ROUTE_CH6 1
|
||||
#define PMIC_MPP_AMUX_ROUTE_CH7 2
|
||||
#define PMIC_MPP_AMUX_ROUTE_CH8 3
|
||||
#define PMIC_MPP_AMUX_ROUTE_ABUS1 4
|
||||
#define PMIC_MPP_AMUX_ROUTE_ABUS2 5
|
||||
#define PMIC_MPP_AMUX_ROUTE_ABUS3 6
|
||||
#define PMIC_MPP_AMUX_ROUTE_ABUS4 7
|
||||
|
||||
/* To be used with "function" */
|
||||
#define PMIC_MPP_FUNC_NORMAL "normal"
|
||||
#define PMIC_MPP_FUNC_PAIRED "paired"
|
||||
#define PMIC_MPP_FUNC_DTEST1 "dtest1"
|
||||
#define PMIC_MPP_FUNC_DTEST2 "dtest2"
|
||||
#define PMIC_MPP_FUNC_DTEST3 "dtest3"
|
||||
#define PMIC_MPP_FUNC_DTEST4 "dtest4"
|
||||
|
||||
#endif
|
||||
Загрузка…
Ссылка в новой задаче