commit 6cca13de26 upstream.
Fix the circular lock dependency and unbalanced unlock of addess0_mutex
introduced when fixing an address0_mutex enumeration retry race in commit
ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race")
Make sure locking order between port_dev->status_lock and address0_mutex
is correct, and that address0_mutex is not unlocked in hub_port_connect
"done:" codepath which may be reached without locking address0_mutex
Fixes: 6ae6dc22d2 ("usb: hub: Fix usb enumeration issue due to address0 race")
Cc: <stable@vger.kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211123101656.1113518-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ae6dc22d2 upstream.
xHC hardware can only have one slot in default state with address 0
waiting for a unique address at a time, otherwise "undefined behavior
may occur" according to xhci spec 5.4.3.4
The address0_mutex exists to prevent this across both xhci roothubs.
If hub_port_init() fails, it may unlock the mutex and exit with a xhci
slot in default state. If the other xhci roothub calls hub_port_init()
at this point we end up with two slots in default state.
Make sure the address0_mutex protects the slot default state across
hub_port_init() retries, until slot is addressed or disabled.
Note, one known minor case is not fixed by this patch.
If device needs to be reset during resume, but fails all hub_port_init()
retries in usb_reset_and_verify_device(), then it's possible the slot is
still left in default state when address0_mutex is unlocked.
Cc: <stable@vger.kernel.org>
Fixes: 638139eb95 ("usb: hub: allow to process more usb hub events in parallel")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211115221630.871204-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional change. Since configuration to stop HCD is invoked from
multiple places, group all of them in usb_stop_hcd().
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-4-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0bd860493f.
While the patch was working as stated,ie preventing the L850-GL LTE modem
from crashing on some U3 wake-ups due to a race condition between the
host wake-up and the modem-side wake-up, when using the MBIM interface,
this would force disabling the USB runtime PM on the device.
The increased power consumption is significant for LTE laptops,
and given that with decently recent modem firmwares, when the modem hits
the bug, it automatically recovers (ie it drops from the bus, but
automatically re-enumerates after less than half a second, rather than being
stuck until a power cycle as it was doing with ancient firmware), for
most people, the trade-off now seems in favor of re-enabling it by
default.
For people with access to the platform code, the bug can also be worked-around
successfully by changing the USB3 LFPM polling off-time for the XHCI
controller in the BIOS code.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210721092516.2775971-1-vpalatin@chromium.org
Fixes: 0bd860493f ("USB: quirks: ignore remote wake-up on Fibocom L850-GL LTE modem")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device initiated link power management U1/U2 states should not be
enabled in case the system exit latency plus one bus interval (125us) is
greater than the shortest service interval of any periodic endpoint.
This is the case for both U1 and U2 sytstem exit latencies and link states.
See USB 3.2 section 9.4.9 "Set Feature" for more details
Note, before this patch the host and device initiated U1/U2 lpm states
were both enabled with lpm. After this patch it's possible to end up with
only host inititated U1/U2 lpm in case the exit latencies won't allow
device initiated lpm.
If this case we still want to set the udev->usb3_lpm_ux_enabled flag so
that sysfs users can see the link may go to U1/U2.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210715150122.1995966-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maximum Exit Latency (MEL) value is used by host to know how much in
advance it needs to start waking up a U1/U2 suspended link in order to
service a periodic transfer in time.
Current MEL calculation only includes the time to wake up the path from
U1/U2 to U0. This is called tMEL1 in USB 3.1 section C 1.5.2
Total MEL = tMEL1 + tMEL2 +tMEL3 + tMEL4 which should additinally include:
- tMEL2 which is the time it takes for PING message to reach device
- tMEL3 time for device to process the PING and submit a PING_RESPONSE
- tMEL4 time for PING_RESPONSE to traverse back upstream to host.
Add the missing tMEL2, tMEL3 and tMEL4 to MEL calculation.
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150122.1995966-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the user submits a control URB via usbfs, the user supplies the
bRequestType value and the kernel uses it to compute the pipe value.
However, do_proc_control() performs this computation incorrectly in
the case where the bRequestType direction bit is set to USB_DIR_IN and
the URB's transfer length is 0: The pipe's direction is also set to IN
but it should be OUT, which is the direction the actual transfer will
use regardless of bRequestType.
Commit 5cc59c418f ("USB: core: WARN if pipe direction != setup
packet direction") added a check to compare the direction bit in the
pipe value to a control URB's actual direction and to WARN if they are
different. This can be triggered by the incorrect computation
mentioned above, as found by syzbot.
This patch fixes the computation, thus avoiding the WARNing.
Reported-and-tested-by: syzbot+72af3105289dcb4c055b@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210712185436.GB326369@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDPuyMeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGvxgH/RKvSuRPwkJ2Jcp9
VLi5kCbqtJlYLq6tB6peSJ8otKgxkcRwC0pIY4LlYIAWYboktLQ5RKp/9nB2h2FN
aMZUMu6AI/lVJyFMI5MnKnJIUiUq+WXR3lSSlw68vwFLFdzqUZFNq+bqeiVvnIy1
yqA6naj24Tu/RbYffQoPvdSJcU2SLXRMxwD8HRGiU2d51RaFsOvsZvF+P5TVcsEV
ZmttJeER21CaI/A809eqaFmyGrUOcZZK9roZEbMwanTZOMw18biEsLu/UH4kBX01
JC4+RlGxcWjQ5YNZgChsgoOK/CHzc6ITztTntdeDWAvwZjQFzV7pCy4/3BWne3O+
5178yHM=
=o8cN
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc7' into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cypress CY7C65632 appears to have an issue with auto suspend and
detecting devices, not too dissimilar to the SMSC 5534B hub. It is
easiest to reproduce by connecting multiple mass storage devices to
the hub at the same time. On a Lenovo Yoga, around 1 in 3 attempts
result in the devices not being detected. It is however possible to
make them appear using lsusb -v.
Disabling autosuspend for this hub resolves the issue.
Fixes: 1208f9e1d7 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210614155524.2228800-1-andrew@lunn.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB core has utility routines to retrieve various types of
descriptors. These routines will now provoke a WARN if they are asked
to retrieve 0 bytes (USB "receive" requests must not have zero
length), so avert this by checking the size argument at the start.
CC: Johan Hovold <johan@kernel.org>
Reported-and-tested-by: syzbot+7dbcd9ff34dc4ed45240@syzkaller.appspotmail.com
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210607152307.GD1768031@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A type of inconsistency that can show up in control URBs is when the
setup packet's wLength value does not match the URB's
transfer_buffer_length field. The two should always be equal;
differences could lead to information leaks or undefined behavior for
OUT transfers or overruns for IN transfers.
This patch adds a test for such mismatches during URB submission. If
the test fails, the submission is rejected with a -EBADR error code
(which is not used elsewhere in the USB core), and a debugging message
is logged for people interested in tracking down these errors.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210526153244.GA1400430@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the "removable" attribute from USB to core in order to allow it to be
supported by other subsystem / buses. Individual buses that want to support
this attribute can populate the removable property of the device while
enumerating it with the 3 possible values -
- "unknown"
- "fixed"
- "removable"
Leaving the field unchanged (i.e. "not supported") would mean that the
attribute would not show up in sysfs for that device. The UAPI (location,
symantics etc) for the attribute remains unchanged.
Move the "removable" attribute from USB to the device core so it can be
used by other subsystems / buses.
By default, devices do not have a "removable" attribute in sysfs.
If a subsystem or bus driver wants to support a "removable" attribute, it
should call device_set_removable() before calling device_register() or
device_add(), e.g.:
device_set_removable(dev, DEVICE_REMOVABLE);
device_register(dev);
The possible values and the resulting sysfs attribute contents are:
DEVICE_REMOVABLE_UNKNOWN -> "unknown"
DEVICE_REMOVABLE -> "removable"
DEVICE_FIXED -> "fixed"
Convert the USB "removable" attribute to use this new device core
functionality. There should be no user-visible change in the location or
semantics of attribute for USB devices.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20210524171812.18095-1-rajatja@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_sndctrlpipe() is evaluated in do_proc_control(), saved in a
variable, then evaluated again. Use the saved variable instead, to
match the use of usb_rcvctrlpipe().
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210521174027.GA116484@m.b4.vu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a control URB is submitted, the direction indicated by URB's pipe
member is supposed to match the direction indicated by the setup
packet's bRequestType member. A mismatch could lead to trouble,
depending on which field the host controller drivers use for
determining the actual direction.
This shouldn't ever happen; it would represent a careless bug in a
kernel driver somewhere. This patch adds a dev_WARN_ONCE to let
people know about the potential problem.
Suggested-by: "Geoffrey D. Bennett" <g@b4.vu>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210522021623.GB1260282@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot found that the kernel generates a WARNing if the user tries to
submit a bulk transfer through usbfs with a buffer that is way too
large. This isn't a bug in the kernel; it's merely an invalid request
from the user and the usbfs code does handle it correctly.
In theory the same thing can happen with async transfers, or with the
packet descriptor table for isochronous transfers.
To prevent the MM subsystem from complaining about these bad
allocation requests, add the __GFP_NOWARN flag to the kmalloc calls
for these buffers.
CC: Andrew Morton <akpm@linux-foundation.org>
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+882a85c0c8ec4a3e2281@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210518201835.GA1140918@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ca91fd8c76 ("USB: Add reset-resume quirk for
WD19's Realtek Hub"). The previous patch in the series now handles
the problematic hubs by checking the port status and handling it
accordingly when PORT_SUSPEND timeout occurs. We don't need to use
reset-resume all the time.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Link: https://lore.kernel.org/r/20210514045405.5261-3-chris.chiu@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the Realtek high-speed Hub(0bda:5487), the port which has wakeup
enabled_descendants will sometimes timeout when setting PORT_SUSPEND
feature. After checking the PORT_SUSPEND bit in wPortStatus, it is
already set which means the port has been suspended. We should treat
it suspended to make sure it will be resumed correctly.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Link: https://lore.kernel.org/r/20210514045405.5261-2-chris.chiu@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use map_urb_for_dma() to improve the dma map code for single step
set feature request urb in test mode.
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1620452039-11694-3-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is needed at USB Certification test for Embedded Host 2.0, and
the detail is at CH6.4.1.1 of On-The-Go and Embedded Host Supplement
to the USB Revision 2.0 Specification. Since other USB 2.0 capable
host like XHCI also need it, so move it to HCD core.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1620452039-11694-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This may happen if the port becomes resume status exactly
when usb_port_resume() gets port status, it still need provide
a TRSMCRY time before access the device.
CC: <stable@vger.kernel.org>
Reported-by: Tianping Fang <tianping.fang@mediatek.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210512020738.52961-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek Hub (0bda:5487) in Dell Dock WD19 sometimes fails to work
after the system resumes from suspend with remote wakeup enabled
device connected:
[ 1947.640907] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641208] usb 5-2.3-port5: cannot disable (err = -71)
[ 1947.641401] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641450] usb 5-2.3-port4: cannot reset (err = -71)
Information of this hub:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 5
D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=5487 Rev= 1.47
S: Manufacturer=Dell Inc.
S: Product=Dell dock
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=01 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
The failure results from the ETIMEDOUT by chance when turning on
the suspend feature for the specified port of the hub. The port
seems to be in an unknown state so the hub_activate during resume
fails the hub_port_status, then the hub will fail to work.
The quirky hub needs the reset-resume quirk to function correctly.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210420174651.6202-1-chris.chiu@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is another branded 8153 device that doesn't work well with LPM
enabled:
[ 400.597506] r8152 5-1.1:1.0 enx482ae3a2a6f0: Tx status -71
So disable LPM to resolve the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1922651
Link: https://lore.kernel.org/r/20210412135455.791971-1-kai.heng.feng@canonical.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return the exactly delay time given by root hub descriptor,
this helps to reduce resume time etc.
Due to the root hub descriptor is usually provided by the host
controller driver, if there is compatibility for a root hub,
we can fix it easily without affect other root hub
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618017645-12259-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
thus a pairing decrement is needed.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210408130831.56239-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing usb_for_each_port(). It works the same way as
usb_for_each_dev(), but instead of going through every USB
device in the system, it walks through the USB ports in the
system.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407065555.88110-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This LTE modem (M.2 card) has a bug in its power management:
there is some kind of race condition for U3 wake-up between the host and
the device. The modem firmware sometimes crashes/locks when both events
happen at the same time and the modem fully drops off the USB bus (and
sometimes re-enumerates, sometimes just gets stuck until the next
reboot).
Tested with the modem wired to the XHCI controller on an AMD 3015Ce
platform. Without the patch, the modem dropped of the USB bus 5 times in
3 days. With the quirk, it stayed connected for a week while the
'runtime_suspended_time' counter incremented as excepted.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210319124802.2315195-1-vpalatin@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's been almost twenty years since the interface "private data" pointer
was removed in favour of using the driver-data pointer of struct device.
Let's rename the driver-data parameter of usb_driver_claim_interface()
so that it better reflects how it's used.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210318155406.22399-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's been almost twenty years since USB drivers returned a data pointer
from their probe routines in order to bind to an interface.
Time to update the documentation for usb_driver_claim_interface().
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210318155406.22399-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB devices cannot perform DMA and hence have no dma_mask set in their
device structure. Therefore importing dmabuf into a USB-based driver
fails, which breaks joining and mirroring of display in X11.
For USB devices, pick the associated USB controller as attachment device.
This allows the DRM import helpers to perform the DMA setup. If the DMA
controller does not support DMA transfers, we're out of luck and cannot
import. Our current USB-based DRM drivers don't use DMA, so the actual
DMA device is not important.
Tested by joining/mirroring displays of udl and radeon under Gnome/X11.
v8:
* release dmadev if device initialization fails (Noralf)
* fix commit description (Noralf)
v7:
* fix use-before-init bug in gm12u320 (Dan)
v6:
* implement workaround in DRM drivers and hold reference to
DMA device while USB device is in use
* remove dev_is_usb() (Greg)
* collapse USB helper into usb_intf_get_dma_device() (Alan)
* integrate Daniel's TODO statement (Daniel)
* fix typos (Greg)
v5:
* provide a helper for USB interfaces (Alan)
* add FIXME item to documentation and TODO list (Daniel)
v4:
* implement workaround with USB helper functions (Greg)
* use struct usb_device->bus->sysdev as DMA device (Takashi)
v3:
* drop gem_create_object
* use DMA mask of USB controller, if any (Daniel, Christian, Noralf)
v2:
* move fix to importer side (Christian, Daniel)
* update SHMEM and CMA helpers for new PRIME callbacks
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 6eb0233ec2 ("usb: don't inherity DMA properties for USB devices")
Tested-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210303133229.3288-1-tzimmermann@suse.de
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
There is no need to save the usb_devices debugfs file as we only need it
when removing it, so have the debugfs code look it up when it is needed
instead, saving the storage.
Link: https://lore.kernel.org/r/YCubCA/trHAF7PtF@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix false-positive build warnings for ARCH=ia64 builds
- Optimize dictionary size for module compression with xz
- Check the compiler and linker versions in Kconfig
- Fix misuse of extra-y
- Support DWARF v5 debug info
- Clamp SUBLEVEL to 255 because stable releases 4.4.x and 4.9.x
exceeded the limit
- Add generic syscall{tbl,hdr}.sh for cleanups across arches
- Minor cleanups of genksyms
- Minor cleanups of Kconfig
-----BEGIN PGP SIGNATURE-----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=sLxb
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Fix false-positive build warnings for ARCH=ia64 builds
- Optimize dictionary size for module compression with xz
- Check the compiler and linker versions in Kconfig
- Fix misuse of extra-y
- Support DWARF v5 debug info
- Clamp SUBLEVEL to 255 because stable releases 4.4.x and 4.9.x
exceeded the limit
- Add generic syscall{tbl,hdr}.sh for cleanups across arches
- Minor cleanups of genksyms
- Minor cleanups of Kconfig
* tag 'kbuild-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (38 commits)
initramfs: Remove redundant dependency of RD_ZSTD on BLK_DEV_INITRD
kbuild: remove deprecated 'always' and 'hostprogs-y/m'
kbuild: parse C= and M= before changing the working directory
kbuild: reuse this-makefile to define abs_srctree
kconfig: unify rule of config, menuconfig, nconfig, gconfig, xconfig
kconfig: omit --oldaskconfig option for 'make config'
kconfig: fix 'invalid option' for help option
kconfig: remove dead code in conf_askvalue()
kconfig: clean up nested if-conditionals in check_conf()
kconfig: Remove duplicate call to sym_get_string_value()
Makefile: Remove # characters from compiler string
Makefile: reuse CC_VERSION_TEXT
kbuild: check the minimum linker version in Kconfig
kbuild: remove ld-version macro
scripts: add generic syscallhdr.sh
scripts: add generic syscalltbl.sh
arch: syscalls: remove $(srctree)/ prefix from syscall tables
arch: syscalls: add missing FORCE and fix 'targets' to make if_changed work
gen_compile_commands: prune some directories
kbuild: simplify access to the kernel's version
...
Instead of storing the version in a single integer and having various
kernel (and userspace) code how it's constructed, export individual
(major, patchlevel, sublevel) components and simplify kernel code that
uses it.
This should also make it easier on userspace.
Signed-off-by: Sasha Levin <sashal@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Without this quirk starting a video capture from the device often fails with
kernel: uvcvideo: Failed to set UVC probe control : -110 (exp. 34).
Signed-off-by: Stefan Ursella <stefan.ursella@wolfvision.net>
Link: https://lore.kernel.org/r/20210210140713.18711-1-stefan.ursella@wolfvision.net
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Done opencode in_serving_softirq() checks in in_serving_softirq() to avoid
cluttering the code, hide them in kcov helpers instead.
Fixes: aee9ddb1d3 ("kcov, usb: only collect coverage from __usb_hcd_giveback_urb in softirq")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/aeb430c5bb90b0ccdf1ec302c70831c1a47b9c45.1609876340.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got reports that some models of this old scanner need
this when using runtime PM.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201207130323.23857-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new control-message helpers include a pipe-type check which is
almost completely redundant.
Control messages are generally sent to the default pipe which always
exists and is of the correct type since its endpoint representation is
created by USB core as part of enumeration for all devices.
There is currently only one instance of a driver in the tree which use
a control endpoint other than endpoint 0 (and it does not use the new
helpers).
Drivers should be testing for the existence of their resources at probe
rather than at runtime, but to catch drivers failing to do so USB core
already does a sanity check on URB submission and triggers a WARN().
Having the same sanity check done in the helper only suppresses the
warning without allowing us to find and fix the drivers.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20201204085110.20055-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return -EREMOTEIO instead of -EINVAL on short control transfers when
using the new usb_control_msg_recv() helper.
EINVAL is used to report invalid arguments (e.g. to the helper) and
should not be used for unrelated errors.
Many driver currently return -EIO on short control transfers but since
host-controller drivers already use -EREMOTEIO for short transfers
whenever the URB_SHORT_NOT_OK flag is set, let's use that here as well.
This also allows usb_control_msg_recv() to eventually use
URB_SHORT_NOT_OK without changing the return value again.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20201204085110.20055-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A failure to send a complete control message is always an error so
there's no need to check for short transfers in usb_control_msg_send().
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20201204085110.20055-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are never modified, so make them const to allow the compiler to
put them in read-only memory. Done with the help of coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201125162500.37228-2-rikard.falkeborn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2f964780c0 ("USB: core: replace %p with %pK") used the %pK
format specifier for a bunch of __user pointers. But as the 'K' in
the specifier indicates, it is meant for kernel pointers. The reason
for the %pK specifier is to avoid leaks of kernel addresses, but when
the pointer is to an address in userspace the security implications
are minimal. In particular, no kernel information is leaked.
This patch changes the __user %pK specifiers (used in a bunch of
debugging output lines) to %px, which will always print the actual
address with no mangling. (Notably, there is no printk format
specifier particularly intended for __user pointers.)
Fixes: 2f964780c0 ("USB: core: replace %p with %pK")
CC: Vamsi Krishna Samavedam <vskrishn@codeaurora.org>
CC: <stable@vger.kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201119170228.GB576844@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
aimed to make the USB stack more reliable by detecting and skipping
over endpoints that are duplicated between interfaces. This caused a
regression for a Hercules audio card (reported as Bugzilla #208357),
which contains such non-compliant duplications. Although the
duplications are harmless, skipping the valid endpoints prevented the
device from working.
This patch fixes the regression by adding ENDPOINT_IGNORE quirks for
the Hercules card, telling the kernel to ignore the invalid duplicate
endpoints and thereby allowing the valid endpoints to be used as
intended.
Fixes: 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
CC: <stable@vger.kernel.org>
Reported-by: Alexander Chalikiopoulos <bugzilla.kernel.org@mrtoasted.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201119170040.GA576844@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a USB_QUIRK_DISCONNECT_SUSPEND quirk for the Lenovo TIO built-in
usb-audio. when A630Z going into S3,the system immediately wakeup 7-8
seconds later by usb-audio disconnect interrupt to avoids the issue.
eg dmesg:
....
[ 626.974091 ] usb 7-1.1: USB disconnect, device number 3
....
....
[ 1774.486691] usb 7-1.1: new full-speed USB device number 5 using xhci_hcd
[ 1774.947742] usb 7-1.1: New USB device found, idVendor=17ef, idProduct=a012, bcdDevice= 0.55
[ 1774.956588] usb 7-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1774.964339] usb 7-1.1: Product: Thinkcentre TIO24Gen3 for USB-audio
[ 1774.970999] usb 7-1.1: Manufacturer: Lenovo
[ 1774.975447] usb 7-1.1: SerialNumber: 000000000000
[ 1775.048590] usb 7-1.1: 2:1: cannot get freq at ep 0x1
.......
Seeking a better fix, we've tried a lot of things, including:
- Check that the device's power/wakeup is disabled
- Check that remote wakeup is off at the USB level
- All the quirks in drivers/usb/core/quirks.c
e.g. USB_QUIRK_RESET_RESUME,
USB_QUIRK_RESET,
USB_QUIRK_IGNORE_REMOTE_WAKEUP,
USB_QUIRK_NO_LPM.
but none of that makes any difference.
There are no errors in the logs showing any suspend/resume-related issues.
When the system wakes up due to the modem, log-wise it appears to be a
normal resume.
Introduce a quirk to disable the port during suspend when the modem is
detected.
Signed-off-by: penghao <penghao@uniontech.com>
Link: https://lore.kernel.org/r/20201118123039.11696-1-penghao@uniontech.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "fallthrough" pseudo-keyword was added as a portable way to denote
intentional fallthrough. Clang will still warn on cases where there is a
fallthrough to an immediate break. Add explicit breaks for those cases.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20201111014716.260633-1-ndesaulniers@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Bugzilla #208257, Julien Humbert reports that a 32-GB Kingston
flash drive spontaneously disconnects and reconnects, over and over.
Testing revealed that disabling Link Power Management for the drive
fixed the problem.
This patch adds a quirk entry for that drive to turn off LPM permanently.
CC: Hans de Goede <jwrdegoede@fedoraproject.org>
CC: <stable@vger.kernel.org>
Reported-and-tested-by: Julien Humbert <julroy67@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201102145821.GA1478741@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Bastien Nocera <hadess@hadess.net>
When a USB device driver has both an id_table and a match() function, make
sure to check both to find a match, first matching the id_table, then
checking the match() function.
This makes it possible to have module autoloading done through the
id_table when devices are plugged in, before checking for further
device eligibility in the match() function.
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Co-developed-by: M. Vefa Bicakci <m.v.b@runbox.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Tested-by: Pan (Pany) YUAN <pany@fedoraproject.org>
Link: https://lore.kernel.org/r/20201022135521.375211-2-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently there's a KCOV remote coverage collection section in
__usb_hcd_giveback_urb(). Initially that section was added based on the
assumption that usb_hcd_giveback_urb() can only be called in interrupt
context as indicated by a comment before it. This is what happens when
syzkaller is fuzzing the USB stack via the dummy_hcd driver.
As it turns out, it's actually valid to call usb_hcd_giveback_urb() in task
context, provided that the caller turned off the interrupts; USB/IP does
exactly that. This can lead to a nested KCOV remote coverage collection
sections both trying to collect coverage in task context. This isn't
supported by KCOV, and leads to a WARNING.
Change __usb_hcd_giveback_urb() to only call kcov_remote_*() callbacks
when it's being executed in a softirq. As the result, the coverage from
USB/IP related usb_hcd_giveback_urb() calls won't be collected, but the
WARNING is fixed.
A potential future improvement would be to support nested remote coverage
collection sections, but this patch doesn't address that.
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Marco Elver <elver@google.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/f3a7a153f0719cb53ec385b16e912798bd3e4cf9.1602856358.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usage of in_interrupt() in drivers is phased out for various reasons.
Various comments use !in_interrupt() to describe calling context for
functions which might sleep. That's wrong because the calling context has
to be preemptible task context, which is not what !in_interrupt()
describes.
Replace !in_interrupt() with more accurate plain text descriptions.
The comment for usb_hcd_poll_rh_status() is misleading as this function is
called from all kinds of contexts including preemptible task
context. Remove it as there is obviously no restriction.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20201019101110.851821025@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common
code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
-----BEGIN PGP SIGNATURE-----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=Bkf/
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
* tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping: (63 commits)
ARM/ixp4xx: add a missing include of dma-map-ops.h
dma-direct: simplify the DMA_ATTR_NO_KERNEL_MAPPING handling
dma-direct: factor out a dma_direct_alloc_from_pool helper
dma-direct check for highmem pages in dma_direct_alloc_pages
dma-mapping: merge <linux/dma-noncoherent.h> into <linux/dma-map-ops.h>
dma-mapping: move large parts of <linux/dma-direct.h> to kernel/dma
dma-mapping: move dma-debug.h to kernel/dma/
dma-mapping: remove <asm/dma-contiguous.h>
dma-mapping: merge <linux/dma-contiguous.h> into <linux/dma-map-ops.h>
dma-contiguous: remove dma_contiguous_set_default
dma-contiguous: remove dev_set_cma_area
dma-contiguous: remove dma_declare_contiguous
dma-mapping: split <linux/dma-mapping.h>
cma: decrease CMA_ALIGNMENT lower limit to 2
firewire-ohci: use dma_alloc_pages
dma-iommu: implement ->alloc_noncoherent
dma-mapping: add new {alloc,free}_noncoherent dma_map_ops methods
dma-mapping: add a new dma_alloc_pages API
dma-mapping: remove dma_cache_sync
53c700: convert to dma_alloc_noncoherent
...
The latest reference to usbfs_conn_disc_event() removed in
commit fb28d58b72 ("USB: remove CONFIG_USB_DEVICEFS")
in 2012 and now a user poll() waits infinitely for content changes.
Signed-off-by: Sergey Korolev <s.korolev@ndmsystems.com>
Link: https://lore.kernel.org/r/20200809161233.13135-1-s.korolev@ndmsystems.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Description based on one by Yasushi Asano:
According to 6.7.22 A-UUT “Device No Response” for connection timeout
of USB OTG and EH automated compliance plan v1.2, enumeration failure
has to be detected within 30 seconds. However, the old and new
enumeration schemes each make a total of 12 attempts, and each attempt
can take 5 seconds to time out, so the PET test fails.
This patch adds a new Kconfig option (CONFIG_USB_FEW_INIT_RETRIES);
when the option is set all the initialization retry loops except the
outermost are reduced to a single iteration. This reduces the total
number of attempts to four, allowing Linux hosts to pass the PET test.
The new option is disabled by default to preserve the existing
behavior. The reduced number of retries may fail to initialize a few
devices that currently do work, but for the most part there should be
no change. And in cases where the initialization does fail, it will
fail much more quickly.
Reported-and-tested-by: yasushi asano <yazzep@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928152217.GB134701@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SET_CONFIG_TRIES macro in hub.c is badly named; it controls the
number of port-initialization retry attempts rather than the number of
Set-Configuration attempts. Furthermore, the USE_NEW_SCHEME macro and
use_new_scheme() function are written in a very confusing manner,
making it almost impossible to figure out exactly what they do or
check that they are correct.
This patch renames SET_CONFIG_TRIES to PORT_INIT_TRIES, removes
USE_NEW_SCHEME entirely, and rewrites use_new_scheme() to be much more
transparent, with added comments explaining how it works. The patch
also pulls the single call site of use_new_scheme() out from the
Get-Descriptor retry loop (where it returns the same value each time)
and renames the local variable used to store the result.
The overall effect is a minor cleanup. However, there is one
functional change: If the "use_both_schemes" module parameter isn't
set (by default it is set), the existing code does only two retry
iterations. After this patch it will always perform four, regardless
of the parameter's value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928152050.GA134701@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 88b7381a93 ("USB: Select better matching USB drivers when
available") inadvertently broke usbip functionality. The commit in
question allows USB device drivers to be explicitly matched with
USB devices via the use of driver-provided identifier tables and
match functions, which is useful for a specialised device driver
to be chosen for a device that can also be handled by another,
more generic, device driver.
Prior, the USB device section of usb_device_match() had an
unconditional "return 1" statement, which allowed user-space to bind
USB devices to the usbip_host device driver, if desired. However,
the aforementioned commit changed the default/fallback return
value to zero. This breaks device drivers such as usbip_host, so
this commit restores the legacy behaviour, but only if a device
driver does not have an id_table and a match() function.
In addition, if usb_device_match is called for a device driver
and device pair where the device does not match the id_table of the
device driver in question, then the device driver will be disqualified
for the device. This allows avoiding the default case of "return 1",
which prevents undesirable probe() calls to a driver even though
its id_table did not match the device.
Finally, this commit changes the specialised-driver-to-generic-driver
transition code so that when a device driver returns -ENODEV, a more
generic device driver is only considered if the current device driver
does not have an id_table and a match() function. This ensures that
"generic" drivers such as usbip_host will not be considered specialised
device drivers and will not cause the device to be locked in to the
generic device driver, when a more specialised device driver could be
tried.
All of these changes restore usbip functionality without regressions,
ensure that the specialised/generic device driver selection logic works
as expected with the usb and apple-mfi-fastcharge drivers, and do not
negatively affect the use of devices provided by dummy_hcd.
Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-5-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit resolves a minor bug in the selection/discovery of more
specific USB device drivers for devices that are currently bound to
generic USB device drivers.
The bug is related to the way a candidate USB device driver is
compared against the generic USB device driver. The code in
is_dev_usb_generic_driver() assumes that the device driver in question
is a USB device driver by calling to_usb_device_driver(dev->driver)
to downcast; however I have observed that this assumption is not always
true, through code instrumentation.
This commit avoids the incorrect downcast altogether by comparing
the USB device's driver (i.e., dev->driver) to the generic USB
device driver directly. This method was suggested by Alan Stern.
This bug was found while investigating Andrey Konovalov's report
indicating usbip device driver misbehaviour with the recently merged
generic USB device driver selection feature. The report is linked
below.
Fixes: d5643d2249 ("USB: Fix device driver race")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-4-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit resolves a bug in the selection/discovery of more
specific USB device drivers for devices that are currently bound to
generic USB device drivers.
The bug is in the logic that determines whether a device currently
bound to a generic USB device driver should be re-probed by a
more specific USB device driver or not. The code in
__usb_bus_reprobe_drivers() used to have the following lines:
if (usb_device_match_id(udev, new_udriver->id_table) == NULL &&
(!new_udriver->match || new_udriver->match(udev) != 0))
return 0;
ret = device_reprobe(dev);
As the reader will notice, the code checks whether the USB device in
consideration matches the identifier table (id_table) of a specific
USB device_driver (new_udriver), followed by a similar check, but this
time with the USB device driver's match function. However, the match
function's return value is not checked correctly. When match() returns
zero, it means that the specific USB device driver is *not* applicable
to the USB device in question, but the code then goes on to reprobe the
device with the new USB device driver under consideration. All this to
say, the logic is inverted.
This bug was found by code inspection and instrumentation while
investigating the root cause of the issue reported by Andrey Konovalov,
where usbip took over syzkaller's virtual USB devices in an undesired
manner. The report is linked below.
Fixes: d5643d2249 ("USB: Fix device driver race")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-3-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They need to specify how memory is to be allocated,
as control messages need to work in contexts that require GFP_NOIO.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200923134348.23862-9-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d6a4992495.
Control messages are needed in contexts when memory allocations
are restricted, such as handling device resets and runtime PM.
For this reason the control message API internally uses GFP_NOIO.
This is a band aid introduced because when we recognized the issue,
the call chains were highly convoluted. Continuing this trend
is not a good idea.
So I am shooting the whole kennel here.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200923134348.23862-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the comment in usb_alloc_dev correctly states, drivers can't use
the DMA API on usb device, and at least calling dma_set_mask on them
is highly dangerous. Unlike what the comment states upper level drivers
also can't really use the presence of a dma mask to check for DMA
support, as the dma_mask is set by default for most busses.
Setting the dma_mask comes from "[PATCH] usbcore dma updates (and doc)"
in BitKeeper times, as it seems like it was primarily for setting the
NETIF_F_HIGHDMA flag in USB drivers, something that has long been
fixed up since.
Setting the dma_pfn_offset comes from commit b44bbc46a8
("usb: core: setup dma_pfn_offset for USB devices and, interfaces"),
which worked around the fact that the scsi_calculate_bounce_limits
functions wasn't going through the proper driver interface to query
DMA information, but that function was removed in commit 21e07dba9f
("scsi: reduce use of block bounce buffers") years ago.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for the BYD zhaoxin notebook.
This notebook come with usb touchpad. And we would like to disable
touchpad wakeup on this notebook by default.
Signed-off-by: Penghao <penghao@uniontech.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200907023026.28189-1-penghao@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few calls to usb_control_msg() that can be converted to use
usb_control_msg_send() instead, so do that in order to make the error
checking a bit simpler and the code smaller.
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200914153756.3412156-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few calls to usb_control_msg() that can be converted to use
usb_control_msg_send() instead, so do that in order to make the error
checking a bit simpler.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200914153756.3412156-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New core functions to make sending/receiving USB control messages easier
and saner.
In discussions, it turns out that the large majority of users of
usb_control_msg() do so in potentially incorrect ways. The most common
issue is where a "short" message is received, yet never detected
properly due to "incorrect" error handling.
Handle all of this in the USB core with two new functions to try to make
working with USB control messages simpler.
No more need for dynamic data, messages can be on the stack, and only
"complete" send/receive will work without causing an error.
Link: https://lore.kernel.org/r/20200914153756.3412156-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snd_usb_pipe_sanity_check() is a great function, so let's move it into
the USB core so that other parts of the kernel, including the USB core,
can call it.
Name it usb_pipe_type_check() to match the existing
usb_urb_ep_type_check() call, which now uses this function.
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Eli Billauer <eli.billauer@gmail.com>
Cc: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexander Tsoy <alexander@tsoy.me>
Cc: "Geoffrey D. Bennett" <g@b4.vu>
Cc: Jussi Laako <jussi@sonarnerd.net>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Dmitry Panchenko <dmitry@d-systems.ee>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jesus Ramos <jesus-ramos@live.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200914153756.3412156-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8bb54ab573 ("usbcore: add usb_device_driver definition") added
the printk() calls with the error massages spoilt due to the stray tabs
in the middle. Remove these tabs and convert printk() calls to pr_err()
for consistency with the other code, while at it.
Fixes: 8bb54ab573 ("usbcore: add usb_device_driver definition")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/4beb55c4-eb34-7744-155f-033b8f527e23@omprussia.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace drivers that use a SetConfiguration() request to "lightweight"
reset an already configured usb device might cause data toggles to get out
of sync between the device and host, and the device becomes unusable.
The xHCI host requires endpoints to be dropped and added back to reset the
toggle. If USB core notices the new configuration is the same as the
current active configuration it will avoid these extra steps by calling
usb_reset_configuration() instead of usb_set_configuration().
A SetConfiguration() request will reset the device side data toggles.
Make sure usb_reset_configuration() function also drops and adds back the
endpoints to ensure data toggles are in sync.
To avoid code duplication split the current usb_disable_device() function
and reuse the endpoint specific part.
Cc: stable <stable@vger.kernel.org>
Tested-by: Martin Thierer <mthierer@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200901082528.12557-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9ML+IeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGA8EIAIy/kTbFS0yrE9yV
hb98oX0z9+EU9YQg9vhaRWwPd+rJF/JMQZLqYcwbhjG9abaUL3T3fEcSAefMHw8E
LAt+hYzA38dHt7tqhsFQX3vV1VorvDVICBVN0yRPRWKKikq4OPIHzaAR9tleGAF5
8btQisl1PjN+obwYmLuNb6aX16OCwAF+uXOwehcoJs9dvMNhwtXRzfOflWzOvOo6
tE0bHErlylLDfLv4ZzEfczTdks4QJZ7C0xLSf3oN9AAynW42Xnhct4hi8qZY/hCf
CMaqeN4hdpub6TvQIqBdDqMMjEXGFgeNSnAEBQY9VpvUqz8NTu6sQxwgJEKDF5tg
d81lv2c=
=uW/F
-----END PGP SIGNATURE-----
Merge 5.9-rc3 into usb-next
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's try this again... Here are some USB fixes for 5.9-rc3.
This differs from the previous pull request for this release in that:
- the usb gadget patch now does not break some systems, and
actually does what it was intended to do. Many thanks to
Marek Szyprowski for quickly noticing and testing the patch
from Andy Shevchenko to resolve this issue.
- some more new USB quirks have been added to get some new
devices to work properly based on user reports.
Other than that, the original pull request patches are all here, and
they contain:
- usb gadget driver fixes
- xhci driver fixes
- typec fixes
- new quirks and ids
- fixes for USB patches that went into 5.9-rc1.
All of these have been tested in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX0t32g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylFMACeLEQgeN1rmfQfLyo2NHROQEeDhnIAniLMhchZ
p9dXWJ8aNeyI5OrNjD5b
=Vd05
-----END PGP SIGNATURE-----
Merge tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Let's try this again... Here are some USB fixes for 5.9-rc3.
This differs from the previous pull request for this release in that
the usb gadget patch now does not break some systems, and actually
does what it was intended to do. Many thanks to Marek Szyprowski for
quickly noticing and testing the patch from Andy Shevchenko to resolve
this issue.
Additionally, some more new USB quirks have been added to get some new
devices to work properly based on user reports.
Other than that, the patches are all here, and they contain:
- usb gadget driver fixes
- xhci driver fixes
- typec fixes
- new quirks and ids
- fixes for USB patches that went into 5.9-rc1.
All of these have been tested in linux-next with no reported issues"
* tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: storage: Add unusual_uas entry for Sony PSZ drives
USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge
usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe()
USB: gadget: u_f: Unbreak offset calculation in VLAs
USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D
usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures
USB: PHY: JZ4770: Fix static checker warning.
USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()
USB: gadget: u_f: add overflow checks to VLA macros
xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed
xhci: Do warm-reset when both CAS and XDEV_RESUME are set
usb: host: xhci: fix ep context print mismatch in debugfs
usb: uas: Add quirk for PNY Pro Elite
tools: usb: move to tools buildsystem
USB: Fix device driver race
USB: Also match device drivers using the ->match vfunc
usb: host: xhci-tegra: fix tegra_xusb_get_phy()
usb: host: xhci-tegra: otg usb2/usb3 port init
usb: hcd: Fix use after free in usb_hcd_pci_remove()
usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port()
...
The Sound Devices MixPre-D audio card suffers from the same defect
as the Sound Devices USBPre2: an endpoint shared between a normal
audio interface and a vendor-specific interface, in violation of the
USB spec. Since the USB core now treats duplicated endpoints as bugs
and ignores them, the audio endpoint isn't available and the card
can't be used for audio capture.
Along the same lines as commit bdd1b147b8 ("USB: quirks: blacklist
duplicate ep on Sound Devices USBPre2"), this patch adds a quirks
entry saying to ignore ep5in for interface 1, leaving it available for
use with standard audio interface 2.
Reported-and-tested-by: Jean-Christophe Barnoud <jcbarnoud@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Fixes: 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
Link: https://lore.kernel.org/r/20200826194624.GA412633@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__check_usb_generic() doesn't explain very well what the
function actually does: It checks to see whether the driver is
non-generic and matches the device.
Change it to check_for_non_generic_match()
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200818110445.509668-2-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a new device with a specialised device driver is plugged in, the
new driver will be modprobe()'d but the driver core will attach the
"generic" driver to the device.
After that, nothing will trigger a reprobe when the modprobe()'d device
driver has finished initialising, as the device has the "generic"
driver attached to it.
Trigger a reprobe ourselves when new specialised drivers get registered.
Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200818110445.509668-3-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only ever used the ID table matching before, but we should also support
open-coded match functions.
Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200818110445.509668-1-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817090209.26351-4-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_kill_anchored_urbs() is commonly used to cancel all URBs on an
anchor just before releasing resources which the URBs rely on. By doing
so, users of this function rely on that no completer callbacks will take
place from any URB on the anchor after it returns.
However if this function is called in parallel with __usb_hcd_giveback_urb
processing a URB on the anchor, the latter may call the completer
callback after usb_kill_anchored_urbs() returns. This can lead to a
kernel panic due to use after release of memory in interrupt context.
The race condition is that __usb_hcd_giveback_urb() first unanchors the URB
and then makes the completer callback. Such URB is hence invisible to
usb_kill_anchored_urbs(), allowing it to return before the completer has
been called, since the anchor's urb_list is empty.
Even worse, if the racing completer callback resubmits the URB, it may
remain in the system long after usb_kill_anchored_urbs() returns.
Hence list_empty(&anchor->urb_list), which is used in the existing
while-loop, doesn't reliably ensure that all URBs of the anchor are gone.
A similar problem exists with usb_poison_anchored_urbs() and
usb_scuttle_anchored_urbs().
This patch adds an external do-while loop, which ensures that all URBs
are indeed handled before these three functions return. This change has
no effect at all unless the race condition occurs, in which case the
loop will busy-wait until the racing completer callback has finished.
This is a rare condition, so the CPU waste of this spinning is
negligible.
The additional do-while loop relies on usb_anchor_check_wakeup(), which
returns true iff the anchor list is empty, and there is no
__usb_hcd_giveback_urb() in the system that is in the middle of the
unanchor-before-complete phase. The @suspend_wakeups member of
struct usb_anchor is used for this purpose, which was introduced to solve
another problem which the same race condition causes, in commit
6ec4147e7b ("usb-anchor: Delay usb_wait_anchor_empty_timeout wake up
till completion is done").
The surely_empty variable is necessary, because usb_anchor_check_wakeup()
must be called with the lock held to prevent races. However the spinlock
must be released and reacquired if the outer loop spins with an empty
URB list while waiting for the unanchor-before-complete passage to finish:
The completer callback may very well attempt to take the very same lock.
To summarize, using usb_anchor_check_wakeup() means that the patched
functions can return only when the anchor's list is empty, and there is
no invisible URB being processed. Since the inner while loop finishes on
the empty list condition, the new do-while loop will terminate as well,
except for when the said race condition occurs.
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200731054650.30644-1-eli.billauer@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_device_match_id() supports being passed NULL tables, so no need to
check for it.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200727104644.149873-1-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just switch the low-level routines to take kernel structures, and do the
conversion from the compat to the native structure on that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20200722073655.220011-1-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function quirks_param_set() takes as argument a const char* pointer
to the new value of the usbcore.quirks parameter. It then casts this
pointer to a non-const char* pointer and passes it to the strsep()
function, which overwrites the value.
Fix this by creating a copy of the value using kstrdup() and letting
that copy be written to by strsep().
Fixes: 027bd6cafd ("usb: core: Add "quirks" parameter for usbcore")
Signed-off-by: Kars Mulder <kerneldev@karsmulder.nl>
Link: https://lore.kernel.org/r/5ee2-5f048a00-21-618c5c00@230659773
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman
Greg Kroah-Hartman
Kishon Vijay Abraham I
Vincent Palatin
Alan Stern
Andrew Lunn
Rajat Jain
Geoffrey D. Bennett
Chris Chiu
Li Jun
Peter Chen
Chunfeng Yun
Kai-Heng Feng
Bixuan Cui
Heikki Krogerus
Thinh Nguyen
Johan Hovold
Thomas Zimmermann
Linus Torvalds
Sasha Levin
Stefan Ursella
Andrey Konovalov
Oliver Neukum
Rikard Falkeborn
penghao
Nick Desaulniers
Bastien Nocera
Ahmed S. Darwish
Sergey Korolev
M. Vefa Bicakci
Christoph Hellwig
Sergey Shtylyov
Zeng Tao
Gustavo A. R. Silva
Allen Pais
Eli Billauer
Andy Shevchenko
Kars Mulder