There are only AMBA_NR_IRQS (2) elements in adev->irq[]. This code
maybe works if the there is a zero directly after the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
mxs dma channel hardware reset command is not reliable and can cause
a channel stall. The only way to fix the channel stall is a DMA engine
reset.
To avoid channel resets we use the hardware semaphore counter. For each
transmitted segment, the DMA channel will decrease the counter by one.
To use this mechanism with cyclic DMA, we need to increase the semaphore
counter with each completed DMA command in the interrupt handler. To
avoid any interruptions between the DMA transfers, the semaphore counter
is initialized with 2. This way the counter can be increased in the
interrupt handler without an influence on the transfer of the DMA
engine.
When disabling the channel, we stop increasing the semaphore counter in
the interrupt handler.
This patch was tested on i.MX28 with the SAIF DMA channel.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After a channel reset, the channel stops running automatically. The
state update was missing so that a channel perperation right after a
channel reset failed.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is no official errata, but I noticed that the channel reset may
stop working if the DMA state engine is in the READ_FLUSH state.
This patch uses the channel debug1 register to wait for the DMA
statemachine to leave the READ_FLUSH state. After that we can continue
to reset the channel.
Tested on i.MX28.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the channel's buffer address register to calculate correct residue
value for tx_status.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DMA interrupt handler uses its controll registers to handle all
available channel interrupts it can find.
This patch changes it to handle only one interrupt by directly mapping
irq number to channel. It also includes a cleanup of the ctrl-register
usage.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support to 8-channel DMA engine, thus the driver works for both
the new 8-channel and the legacy 4-channel DMA engines.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Freescale QorIQ T4 and B4 introduce new 8-channel DMA engines, this patch adds
the device tree nodes for them.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch updates the discription of each type of DMA controller and its
channels, it is preparation for adding another new DMA controller binding, it
also fixes some defects of indent for text alignment at the same time.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This resolves a number of warnings such as the below when building with
64-bit dma_addr_t on arm:
drivers/dma/imx-sdma.c:1092:3: warning: format '%x' expects argument of
type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
..by upcasting to u64 and using %llx.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This resolves a number of warnings such as the below when building with
64-bit dma_addr_t on arm:
drivers/dma/ipu/ipu_idmac.c:1235:2: warning: format '%x' expects argument
of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
..by upcasting to u64 and using %llx.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
fixing of freeing descriptor memory was applied twice, so remove the one
duplicate
Reported-by: Wing-Keung Wang <wingkeung.wang@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Return code of pm_runtime_get_sync() > 0 is not an error and may happen.
Noticed during rmmod & modprobe testing.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Most of the logic here is try and error since what actually happens does
not match the trm or I miss read it.
My first assumption was that the queue on which the tear-down descriptor
completes (their own complete queue vs "active descriptor" complete
queue) depends on the transfer direction. This seems not to be true
because I manage to trigger
| WARN_ON(c->desc_phys != desc_phys);
and the other few were fine means the tear-down descriptor was valid but
on different queue.
This patch changes the logic here to look on both queues for the
descriptor.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use cppi41_pop_desc() when appropriate instead of open-coding the same
functionality again. That makes the code more readable. The function has
to be moved some lines up for this change.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With active users over suspend/resume cycles, it turns out that
more registers, in particular DMA_TDFDQ and RXHPCRA0, have to be
restored on resume.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Using the PaRAM configuration function that we split for reuse by the
different DMA types, we implement Cyclic DMA support.
For the cyclic case, we pass different configuration parameters to this
function, and handle all the Cyclic-specific functionality separately.
Callbacks to the DMA users are handled using vchan_cyclic_callback in
the virt-dma layer. Linking is handled the same way as the slave SG case
except for the last slot where we link it back to the first one in a
cyclic fashion.
For continuity, we check for cases where no.of periods is great than the
MAX number of slots the driver can allocate for a particular descriptor
and error out on such cases.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.
Driver core change:
"device-core: Ensure drvdata = NULL when no driver is bound"
(sha1: 0998d06310)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
drivers/dma/imx-dma.c:575:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t'
drivers/dma/imx-dma.c:575:3: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t'
drivers/dma/imx-dma.c:589:4: warning: format '%x' expects argument of type 'unsigned int', but argument 9 has type 'dma_addr_t'
drivers/dma/imx-dma.c:599:4: warning: format '%x' expects argument of type 'unsigned int', but argument 9 has type 'dma_addr_t'
drivers/dma/imx-dma.c:929:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t'
drivers/dma/imx-dma.c:929:2: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t'
drivers/dma/imx-dma.c:959:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t'
drivers/dma/imx-dma.c:959:2: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t'
We can't use the %pa format for these because this relates to phys_addr_t,
and dma_addr_t can be a different size. So, fix these by converting them
to %llx and casting the dma_addr_t to always be unsigned long long.
While we're here, also use %zu for size_t.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
edma header defines DMA_COMPLETE, this causes issues as commit adfedd9a32 move
DMA_SUCCESS to DMA_COMPLETE. edma should properly namespace its defines and
needs a future fix
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull parisc fix from Helge Deller:
"This is a 2-line patch to save the CPU register which holds our task
thread info pointer before calling a firmware function and then to
restore it again afterwards.
This is necessary because on some 64bit machines the high-order 32bits
are being clobbered by the firmware call, and thus we failed to bring
up secondary CPUs (and instead crashed the kernel) in some situations
eg if we had more than 4GB RAM. This patch fixes a bug which has been
since ever in the parisc linux kernel and which prevented some people
to use a 64bit kernel"
* 'parisc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Do not crash 64bit SMP kernels on machines with >= 4GB RAM
Pull timer fix from Ingo Molnar:
"This tree contains a clockevents regression fix for certain ARM
subarchitectures"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents: Sanitize ticks to nsec conversion
Pull perf fixes from Ingo Molnar:
"The tree contains three fixes:
- Two tooling fixes
- Reversal of the new 'MMAP2' extended mmap record ABI, introduced in
this merge window. (Patches were proposed to fix it but it was all
a bit late and we felt it's safer to just delay the ABI one more
kernel release and do it right)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Disable PERF_RECORD_MMAP2 support
perf scripting perl: Fix build error on Fedora 12
perf probe: Fix to initialize fname always before use it
Pull locking fix from Ingo Molnar:
"This tree fixes a boot crash in CONFIG_DEBUG_MUTEXES=y kernels, on
kernels built with GCC 3.x (there are still such distros)"
Side note: it's not just a fix for old gcc versions, it's also removing
an incredibly broken/subtle check that LLVM had issues with, and that
made no sense.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mutex: Avoid gcc version dependent __builtin_constant_p() usage
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target pending fixes for v3.12-rc7.
This includes a number of EXTENDED_COPY related fixes as a result of
Thomas and Doug's continuing testing and feedback.
Also included is an important vhost/scsi fix that addresses a long
standing issue where the 'write' parameter for get_user_pages_fast()
was incorrectly set for virtio-scsi WRITEs -> DMA_TO_DEVICE, and not
for virtio-scsi READs -> DMA_FROM_DEVICE.
This resulted in random userspace segfaults and other unpleasantness
on KVM host, and unfortunately has been an issue since the initial
merge of vhost/scsi in v3.6. This patch is CC'ed to stable, along
with two other less critical items"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
vhost/scsi: Fix incorrect usage of get_user_pages_fast write parameter
target/pscsi: fix return value check
target: Fail XCOPY for non matching source + destination block_size
target: Generate failure for XCOPY I/O with non-zero scsi_status
target: Add missing XCOPY I/O operation sense_buffer
iser-target: check device before dereferencing its variable
target: Return an error for WRITE SAME with ANCHOR==1
target: Fix assignment of LUN in tracepoints
target: Reject EXTENDED_COPY when emulate_3pc is disabled
target: Allow non zero ListID in EXTENDED_COPY parameter list
target: Make target_do_xcopy failures return INVALID_PARAMETER_LIST
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the late fixes pull request for dmaengine while you fly back
from KS.
We have a new dmaengine ML hosted by vger so a patch for that along
with addition of Dave as driver mainatainer for ioat. Other fixes are
memeory leak fixes on edma driver, small fixes on rcar-hpbdma driver
by Sergei"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: edma: fix another memory leak
dma: edma: Fix memory leak
MAINTAINERS: add to ioatdma maintainer list
MAINTAINERS: add the new dmaengine mailing list
Since the beginning of the parisc-linux port, sometimes 64bit SMP kernels were
not able to bring up other CPUs than the monarch CPU and instead crashed the
kernel. The reason was unclear, esp. since it involved various machines (e.g.
J5600, J6750 and SuperDome). Testing showed, that those crashes didn't happened
when less than 4GB were installed, or if a 32bit Linux kernel was booted.
In the end, the fix for those SMP problems is trivial:
During the early phase of the initialization of the CPUs, including the monarch
CPU, the PDC_PSW firmware function to enable WIDE (=64bit) mode is called.
It's documented that this firmware function may clobber various registers, and
one one of those possibly clobbered registers is %cr30 which holds the task
thread info pointer.
Now, if %cr30 would always have been clobbered, then this bug would have been
detected much earlier. But lots of testing finally showed, that - at least for
%cr30 - on some machines only the upper 32bits of the 64bit register suddenly
turned zero after the firmware call.
So, after finding the root cause, the explanation for the various crashes
became clear:
- On 32bit SMP Linux kernels all upper 32bit were zero, so we didn't faced this
problem.
- Monarch CPUs in 64bit mode always booted sucessfully, because the inital task
thread info pointer was below 4GB.
- Secondary CPUs booted sucessfully on machines with less than 4GB RAM because
the upper 32bit were zero anyay.
- Secondary CPus failed to boot if we had more than 4GB RAM and the task thread
info pointer was located above the 4GB boundary.
Finally, the patch to fix this problem is trivial by saving the %cr30 register
before the firmware call and restoring it afterwards.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 2.6.12+
Signed-off-by: Helge Deller <deller@gmx.de>
- Fix for rounding errors in intel_pstate causing CPU utilization to
be underestimated from Brennan Shacklett.
- intel_pstate fix to always use the correct max pstate value when
computing the min pstate from Dirk Brandewie.
- Hibernation fix for deadlocking resume in cases when the probing
of the device containing the image is deferred from Russ Dill.
- acpi-cpufreq fix to prevent the module from staying in memory
when the driver cannot be registered and then attempting to
unregister things that have never been registered on exit.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=PsHF
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from
"These fix two bugs in the intel_pstate driver, a hibernate bug leading
to nasty resume failures sometimes and acpi-cpufreq initialization bug
that causes problems to happen during module unload when intel_pstate
is in use.
Specifics:
- Fix for rounding errors in intel_pstate causing CPU utilization to
be underestimated from Brennan Shacklett.
- intel_pstate fix to always use the correct max pstate value when
computing the min pstate from Dirk Brandewie.
- Hibernation fix for deadlocking resume in cases when the probing of
the device containing the image is deferred from Russ Dill.
- acpi-cpufreq fix to prevent the module from staying in memory when
the driver cannot be registered and then attempting to unregister
things that have never been registered on exit"
* tag 'pm+acpi-3.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
acpi-cpufreq: Fail initialization if driver cannot be registered
PM / hibernate: Move software_resume to late_initcall_sync
intel_pstate: Correct calculation of min pstate value
intel_pstate: Improve accuracy by not truncating until final result
Woodhouse:
* Revert pxa3xx to its old name to avoid breaking existing 'mtdparts=' boot
strings.
* Return GPMI NAND to its legacy ECC layout for backwards compatibility. We
will revisit this in 3.13.
A note from David on the latter fix: "This leaves a harmless cosmetic warning
about an unused function. At this point in the cycle I really don't care."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=3NKt
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20131025' of git://git.infradead.org/linux-mtd
Pull final mtd fixes from Brian Norris:
"A few more last-minute regression fixes, prepared jointly by me and
David Woodhouse:
- Revert pxa3xx to its old name to avoid breaking existing
'mtdparts=' boot strings.
- Return GPMI NAND to its legacy ECC layout for backwards
compatibility. We will revisit this in 3.13.
A note from David on the latter fix: 'This leaves a harmless cosmetic
warning about an unused function. At this point in the cycle I really
don't care.'"
* tag 'for-linus-20131025' of git://git.infradead.org/linux-mtd:
mtd: gpmi: fix ECC regression
mtd: nand: pxa3xx: Fix registered MTD name
This patch addresses a long-standing bug where the get_user_pages_fast()
write parameter used for setting the underlying page table entry permission
bits was incorrectly set to write=1 for data_direction=DMA_TO_DEVICE, and
passed into get_user_pages_fast() via vhost_scsi_map_iov_to_sgl().
However, this parameter is intended to signal WRITEs to pinned userspace
PTEs for the virtio-scsi DMA_FROM_DEVICE -> READ payload case, and *not*
for the virtio-scsi DMA_TO_DEVICE -> WRITE payload case.
This bug would manifest itself as random process segmentation faults on
KVM host after repeated vhost starts + stops and/or with lots of vhost
endpoints + LUNs.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Asias He <asias@redhat.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case of error, the function scsi_host_lookup() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The "legacy" ECC layout used until 3.12-rc1 uses all the OOB area by
computing the ECC strength and ECC step size ourselves.
Commit 2febcdf84b ("mtd: gpmi: set the BCHs geometry with the ecc info")
makes the driver use the ECC info (ECC strength and ECC step size)
provided by the MTD code, and creates a different NAND ECC layout
for the BCH, and use the new ECC layout. This causes a regression:
We can not mount the ubifs which was created by the old NAND ECC layout.
This patch fixes this issue by reverting to the legacy ECC layout.
We will probably introduce a new device-tree property to indicate that
the new ECC layout can be used. For now though, for the imminent 3.12
release, we just unconditionally revert to the 3.11 behaviour.
This leaves a harmless cosmetic warning about an unused function. At
this point in the cycle I really don't care.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
This issue was first pointed out by Jiaxing Wang several months ago, but no
further comments:
https://lkml.org/lkml/2013/6/29/41
As we know pread() does not change f_pos, so after pread(), file->f_pos
and m->read_pos become different. And seq_lseek() does not update file->f_pos
if offset equals to m->read_pos, so after pread() and seq_lseek()(lseek to
m->read_pos), then a subsequent read may read from a wrong position, the
following program produces the problem:
char str1[32] = { 0 };
char str2[32] = { 0 };
int poffset = 10;
int count = 20;
/*open any seq file*/
int fd = open("/proc/modules", O_RDONLY);
pread(fd, str1, count, poffset);
printf("pread:%s\n", str1);
/*seek to where m->read_pos is*/
lseek(fd, poffset+count, SEEK_SET);
/*supposed to read from poffset+count, but this read from position 0*/
read(fd, str2, count);
printf("read:%s\n", str2);
out put:
pread:
ck_netbios_ns 12665
read:
nf_conntrack_netbios
/proc/modules:
nf_conntrack_netbios_ns 12665 0 - Live 0xffffffffa038b000
nf_conntrack_broadcast 12589 1 nf_conntrack_netbios_ns, Live 0xffffffffa0386000
So we always update file->f_pos to offset in seq_lseek() to fix this issue.
Signed-off-by: Jiaxing Wang <hello.wjx@gmail.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make acpi_cpufreq_init() return error codes when the driver cannot be
registered so that the module doesn't stay useless in memory and so
that acpi_cpufreq_exit() doesn't attempt to unregister things that
have never been registered when the module is unloaded.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
There's really only one bugfix in this branch, which is a fix for timers on
the integrator platform. Since Linus Walleij is resurrecting support for
the platform it seems valuable to get the fix into 3.12 even though the
regression has been around a while.
The rest are a handful of maintainers updates. If you prefer to hold those
until 3.13 then just merge the first patch on the branch which is the fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7MQ0
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"There's really only one bugfix in this branch, which is a fix for
timers on the integrator platform. Since Linus Walleij is
resurrecting support for the platform it seems valuable to get the fix
into 3.12 even though the regression has been around a while.
The rest are a handful of maintainers updates. If you prefer to hold
those until 3.13 then just merge the first patch on the branch which
is the fix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add maintainers entry for Rockchip SoCs
MAINTAINERS: Tegra updates, and driver ownership
MAINTAINERS: ARM: mvebu: add Sebastian Hesselbarth
ARM: integrator: deactivate timer0 on the Integrator/CP
- Fix long standing memory leak in the (rarely used) public key support
- Fix large file corruption on 32 bit architectures
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=74EV
-----END PGP SIGNATURE-----
Merge tag 'ecryptfs-3.12-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
"Two important fixes
- Fix long standing memory leak in the (rarely used) public key
support
- Fix large file corruption on 32 bit architectures"
* tag 'ecryptfs-3.12-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: fix 32 bit corruption issue
ecryptfs: Fix memory leakage in keystore.c
after all the users are converted
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Dan Carpenter
Markus Pargmann
Hongbo Zhang
Olof Johansson
Vinod Koul
Sebastian Andrzej Siewior
Daniel Mack
Sebastian Andrzej Siewior
Joel Fernandes
Michal Simek
Russell King
Linus Torvalds
Helge Deller
Nicholas Bellinger
Wei Yongjun
David Woodhouse
Gu Zheng
Rafael J. Wysocki