[ Upstream commit 391c18cf77 ]
trans_xen did not check the data fits into the buffer before copying
from the xen ring, but we probably should.
Add a check that just skips the request and return an error to
userspace if it did not fit
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Christian Schoenebeck <linux_oss@crudebyte.com>
Link: https://lkml.kernel.org/r/20221118135542.63400-1-asmadeus@codewreck.org
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aa07f7289 ]
If there's a disconnection while operating in eSS, there may be a delay
in VBUS drop response from the connector. In that case, the internal
link state may drop to operate in usb2 speed while the controller thinks
the VBUS is still high. The driver must make sure to disable
GUSB2PHYCFG.SUSPHY when sending endpoint command while in usb2 speed.
The End Transfer command may be called, and only that command needs to
go through at this point. Let's keep it simple and unconditionally
disable GUSB2PHYCFG.SUSPHY whenever we issue the command.
This scenario is not seen in real hardware. In a rare case, our
prototype type-c controller/interface may have a slow response
triggerring this issue.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5651117207803c26e2f22ddf4e5ce9e865dcf7c7.1668045468.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31a6297b89 ]
Status is reported as always off in the 6032 case. Status
reporting now matches the logic in the setters. Once of
the differences to the 6030 is that there are no groups,
therefore the state needs to be read out in the lower bits.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20221120221208.3093727-3-andreas@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a11452a370 ]
When trying to see if we can clone a file range, there are cases where we
end up sending two write operations in case the inode from the source root
has an i_size that is not sector size aligned and the length from the
current offset to its i_size is less than the remaining length we are
trying to clone.
Issuing two write operations when we could instead issue a single write
operation is not incorrect. However it is not optimal, specially if the
extents are compressed and the flag BTRFS_SEND_FLAG_COMPRESSED was passed
to the send ioctl. In that case we can end up sending an encoded write
with an offset that is not sector size aligned, which makes the receiver
fallback to decompressing the data and writing it using regular buffered
IO (so re-compressing the data in case the fs is mounted with compression
enabled), because encoded writes fail with -EINVAL when an offset is not
sector size aligned.
The following example, which triggered a bug in the receiver code for the
fallback logic of decompressing + regular buffer IO and is fixed by the
patchset referred in a Link at the bottom of this changelog, is an example
where we have the non-optimal behaviour due to an unaligned encoded write:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdj
MNT=/mnt/sdj
mkfs.btrfs -f $DEV > /dev/null
mount -o compress $DEV $MNT
# File foo has a size of 33K, not aligned to the sector size.
xfs_io -f -c "pwrite -S 0xab 0 33K" $MNT/foo
xfs_io -f -c "pwrite -S 0xcd 0 64K" $MNT/bar
# Now clone the first 32K of file bar into foo at offset 0.
xfs_io -c "reflink $MNT/bar 0 0 32K" $MNT/foo
# Snapshot the default subvolume and create a full send stream (v2).
btrfs subvolume snapshot -r $MNT $MNT/snap
btrfs send --compressed-data -f /tmp/test.send $MNT/snap
echo -e "\nFile bar in the original filesystem:"
od -A d -t x1 $MNT/snap/bar
umount $MNT
mkfs.btrfs -f $DEV > /dev/null
mount $DEV $MNT
echo -e "\nReceiving stream in a new filesystem..."
btrfs receive -f /tmp/test.send $MNT
echo -e "\nFile bar in the new filesystem:"
od -A d -t x1 $MNT/snap/bar
umount $MNT
Before this patch, the send stream included one regular write and one
encoded write for file 'bar', with the later being not sector size aligned
and causing the receiver to fallback to decompression + buffered writes.
The output of the btrfs receive command in verbose mode (-vvv):
(...)
mkfile o258-7-0
rename o258-7-0 -> bar
utimes
clone bar - source=foo source offset=0 offset=0 length=32768
write bar - offset=32768 length=1024
encoded_write bar - offset=33792, len=4096, unencoded_offset=33792, unencoded_file_len=31744, unencoded_len=65536, compression=1, encryption=0
encoded_write bar - falling back to decompress and write due to errno 22 ("Invalid argument")
(...)
This patch avoids the regular write followed by an unaligned encoded write
so that we end up sending a single encoded write that is aligned. So after
this patch the stream content is (output of btrfs receive -vvv):
(...)
mkfile o258-7-0
rename o258-7-0 -> bar
utimes
clone bar - source=foo source offset=0 offset=0 length=32768
encoded_write bar - offset=32768, len=4096, unencoded_offset=32768, unencoded_file_len=32768, unencoded_len=65536, compression=1, encryption=0
(...)
So we get more optimal behaviour and avoid the silent data loss bug in
versions of btrfs-progs affected by the bug referred by the Link tag
below (btrfs-progs v5.19, v5.19.1, v6.0 and v6.0.1).
Link: https://lore.kernel.org/linux-btrfs/cover.1668529099.git.fdmanana@suse.com/
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd5e1e4282 ]
The `nettest` binary, built from `selftests/net/nettest.c`,
was expected to be found in the path during test execution of
`fcnal-test.sh` and `pmtu.sh`, leading to tests getting
skipped when the binary is not installed in the system, as can
be seen in these logs found in the wild [1]:
# TEST: vti4: PMTU exceptions [SKIP]
[ 350.600250] IPv6: ADDRCONF(NETDEV_CHANGE): veth_b: link becomes ready
[ 350.607421] IPv6: ADDRCONF(NETDEV_CHANGE): veth_a: link becomes ready
# 'nettest' command not found; skipping tests
# xfrm6udp not supported
# TEST: vti6: PMTU exceptions (ESP-in-UDP) [SKIP]
[ 351.605102] IPv6: ADDRCONF(NETDEV_CHANGE): veth_b: link becomes ready
[ 351.612243] IPv6: ADDRCONF(NETDEV_CHANGE): veth_a: link becomes ready
# 'nettest' command not found; skipping tests
# xfrm4udp not supported
The `unicast_extensions.sh` tests also rely on `nettest`, but
it runs fine there because it looks for the binary in the
current working directory [2]:
The same mechanism that works for the Unicast extensions tests
is here copied over to the PMTU and functional tests.
[1] https://lkft.validation.linaro.org/scheduler/job/5839508#L6221
[2] https://lkft.validation.linaro.org/scheduler/job/5839508#L7958
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05530ef7cf ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed.
seq_copy_in_user() and seq_copy_in_kernel() did not have prototypes
matching snd_seq_dump_func_t. Adjust this and remove the casts. There
are not resulting binary output differences.
This was found as a result of Clang's new -Wcast-function-type-strict
flag, which is more sensitive than the simpler -Wcast-function-type,
which only checks for type width mismatches.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202211041527.HD8TLSE1-lkp@intel.com
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221118232346.never.380-kees@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b24dfa587 ]
Sony's downstream driver [1], among some other changes, adds a
seemingly random 10ms usleep_range, which turned out to be necessary
for the hardware to function properly on at least Sony Xperia 1 IV.
Without this, I2C transactions with the SLG51000 straight up fail.
Relax (10-10ms -> 10-11ms) and add the aforementioned sleep to make
sure the hardware has some time to wake up.
(nagara-2.0.0-mlc/vendor/semc/hardware/camera-kernel-module/)
[1] https://developer.sony.com/file/download/open-source-archive-for-64-0-m-4-29/
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221118131035.54874-1-konrad.dybcio@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7d7d4e7bb ]
Due to the hardware behavior, it takes some time for CBJ detection/impedance sensing/de-bounce.
The ClockStop_NotFinished flag will be raised until these functions are completed.
In ClockStopMode0 mode case, the SdW controller might check this flag from D3 to D0 when the
jack detection interrupt happened.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20221116090318.5017-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da74858a47 ]
The clock source and the sched_clock provided by the arm_global_timer
on Rockchip rk3066a/rk3188 are quite unstable because their rates
depend on the CPU frequency.
Recent changes to the arm_global_timer driver makes it impossible to use.
On the other side, the arm_global_timer has a higher rating than the
ROCKCHIP_TIMER, it will be selected by default by the time framework
while we want to use the stable Rockchip clock source.
Keep the arm_global_timer disabled in order to have the
DW_APB_TIMER (rk3066a) or ROCKCHIP_TIMER (rk3188) selected by default.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/f275ca8d-fd0a-26e5-b978-b7f3df815e0a@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d10e90cee ]
A DEVAPC violation occurs when removing the module
due to accessing HW registers without base clock.
To fix this bug, the correct method is:
1. Call the runtime resume function to enable the
clock;
2. Operate the registers to reset the HW;
3. Turn off the clocks and disable the device
RPM mechanism.
Signed-off-by: Zhichao Liu <zhichao.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110072839.30961-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ca507bf99 ]
DSPCLK_DIV field in WM8962_CLOCKING1 register is used to generate
correct frequency of LRCLK and BCLK. Sometimes the read-only value
can't be updated timely after enabling SYSCLK. This results in wrong
calculation values. Delay is introduced here to wait for newest value
from register. The time of the delay should be at least 500~1000us
according to test.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221109121354.123958-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 340a982825 ]
Actually in no-MMU SoCs(i.e. i.MXRT) ZERO_PAGE(vaddr) expands to
```
virt_to_page(0)
```
that in order expands to:
```
pfn_to_page(virt_to_pfn(0))
```
and then virt_to_pfn(0) to:
```
((((unsigned long)(0) - PAGE_OFFSET) >> PAGE_SHIFT) +
PHYS_PFN_OFFSET)
```
where PAGE_OFFSET and PHYS_PFN_OFFSET are the DRAM offset(0x80000000) and
PAGE_SHIFT is 12. This way we obtain 16MB(0x01000000) summed to the base of
DRAM(0x80000000).
When ZERO_PAGE(0) is then used, for example in bio_add_page(), the page
gets an address that is out of DRAM bounds.
So instead of using fake virtual page 0 let's allocate a dedicated
zero_page during paging_init() and assign it to a global 'struct page *
empty_zero_page' the same way mmu.c does and it's the same approach used
in m68k with commit dc068f4621 as discussed here[0]. Then let's move
ZERO_PAGE() definition to the top of pgtable.h to be in common between
mmu.c and nommu.c.
[0]: https://lore.kernel.org/linux-m68k/2a462b23-5b8e-bbf4-ec7d-778434a3b9d7@google.com/T/#m1266ceb63
ad140743174d6b3070364d3c9a5179b
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ee47dcfff ]
We must prevent the CPU from reordering the files->count read with the
FD table access like this, on architectures where read-read reordering is
possible:
files_lookup_fd_raw()
close_fd()
put_files_struct()
atomic_read(&files->count)
I would like to mark this for stable, but the stable rules explicitly say
"no theoretical races", and given that the FD table pointer and
files->count are explicitly stored in the same cacheline, this sort of
reordering seems quite unlikely in practice...
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11871e20bc ]
The lcdc1-rgb24 node name is out of line with the rest
of the rk3188 lcdc1 node, so fix it.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/7b9c0a6f-626b-07e8-ae74-7e0f08b8d241@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de0d04b978 ]
Fix ir-receiver node names on Rockchip boards,
so that they match with regex: '^ir(-receiver)?(@[a-f0-9]+)?$'
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/e9764253-8ce8-150b-4820-41f03f845469@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd847fe34c ]
Fix ir-receiver node names on Rockchip boards,
so that they match with regex: '^ir(-receiver)?(@[a-f0-9]+)?$'
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/ea5af279-f44c-afea-023d-bb37f5a0d58d@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6122f3be70 ]
'clock-frequency' is not part of the DT binding and not supported by the
Linux driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20221024165549.74574-5-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 849c19d149 ]
I2S1 pins are exposed on 40-pin header on Radxa ROCK Pi 4 series.
their default function is GPIO, so I2S1 need to be disabled.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20220924112812.1219-1-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c61bfb1cb6 ]
The clk_disable_unprepare() should be called in the error handling
of devm_clk_bulk_get_optional, fix it by replacing devm_clk_get_optional
and clk_prepare_enable by devm_clk_get_optional_enabled.
Fixes: f5eccd94b6 ("mmc: mediatek: Add subsys clock control for MT8192 msdc")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221125090141.3626747-1-cuigaosheng1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ef9651e97 ]
When a driver keeps a clock prepared (or enabled) during the whole
lifetime of the driver, these helpers allow to simplify the drivers.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <aardelean@deviqon.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220520075737.758761-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stable-dep-of: c61bfb1cb6 ("mmc: mtk-sd: Fix missing clk_disable_unprepare in msdc_of_clock_parse()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abae8e57e4 ]
Allow to add an exit hook to devm managed clocks. Also use
clk_get_optional() in devm_clk_get_optional instead of open coding it.
The generalisation will be used in the next commit to add some more
devm_clk helpers.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <aardelean@deviqon.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220520075737.758761-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stable-dep-of: c61bfb1cb6 ("mmc: mtk-sd: Fix missing clk_disable_unprepare in msdc_of_clock_parse()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bce9332220 upstream.
proc_skip_spaces() seems to think it is working on C strings, and ends
up being just a wrapper around skip_spaces() with a really odd calling
convention.
Instead of basing it on skip_spaces(), it should have looked more like
proc_skip_char(), which really is the exact same function (except it
skips a particular character, rather than whitespace). So use that as
inspiration, odd coding and all.
Now the calling convention actually makes sense and works for the
intended purpose.
Reported-and-tested-by: Kyle Zeng <zengyhkyle@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6cfaf34be upstream.
proc_get_long() is passed a size_t, but then assigns it to an 'int'
variable for the length. Let's not do that, even if our IO paths are
limited to MAX_RW_COUNT (exactly because of these kinds of type errors).
So do the proper test in the rigth type.
Reported-by: Kyle Zeng <zengyhkyle@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b52be557e2 upstream.
When __do_semtimedop() goes to sleep because it has to wait for a
semaphore value becoming zero or becoming bigger than some threshold, it
links the on-stack sem_queue to the sem_array, then goes to sleep
without holding a reference on the sem_array.
When __do_semtimedop() comes back out of sleep, one of two things must
happen:
a) We prove that the on-stack sem_queue has been disconnected from the
(possibly freed) sem_array, making it safe to return from the stack
frame that the sem_queue exists in.
b) We stabilize our reference to the sem_array, lock the sem_array, and
detach the sem_queue from the sem_array ourselves.
sem_array has RCU lifetime, so for case (b), the reference can be
stabilized inside an RCU read-side critical section by locklessly
checking whether the sem_queue is still connected to the sem_array.
However, the current code does the lockless check on sem_queue before
starting an RCU read-side critical section, so the result of the
lockless check immediately becomes useless.
Fix it by doing rcu_read_lock() before the lockless check. Now RCU
ensures that if we observe the object being on our queue, the object
can't be freed until rcu_read_unlock().
This bug is only hittable on kernel builds with full preemption support
(either CONFIG_PREEMPT or PREEMPT_DYNAMIC with preempt=full).
Fixes: 370b262c89 ("ipc/sem: avoid idr tree lookup for interrupted semop")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23393c6461 upstream.
Currently tpm transactions are executed unconditionally in
tpm_pm_suspend() function, which may lead to races with other tpm
accessors in the system.
Specifically, the hw_random tpm driver makes use of tpm_get_random(),
and this function is called in a loop from a kthread, which means it's
not frozen alongside userspace, and so can race with the work done
during system suspend:
tpm tpm0: tpm_transmit: tpm_recv: error -52
tpm tpm0: invalid TPM_STS.x 0xff, dumping stack for forensics
CPU: 0 PID: 1 Comm: init Not tainted 6.1.0-rc5+ #135
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.0-20220807_005459-localhost 04/01/2014
Call Trace:
tpm_tis_status.cold+0x19/0x20
tpm_transmit+0x13b/0x390
tpm_transmit_cmd+0x20/0x80
tpm1_pm_suspend+0xa6/0x110
tpm_pm_suspend+0x53/0x80
__pnp_bus_suspend+0x35/0xe0
__device_suspend+0x10f/0x350
Fix this by calling tpm_try_get_ops(), which itself is a wrapper around
tpm_chip_start(), but takes the appropriate mutex.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Tested-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Vlastimil Babka <vbabka@suse.cz>
Link: https://lore.kernel.org/all/c5ba47ef-393f-1fba-30bd-1230d1b4b592@suse.cz/
Cc: stable@vger.kernel.org
Fixes: e891db1a18 ("tpm: turn on TPM on suspend for TPM 1.x")
[Jason: reworked commit message, added metadata]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d9f15a9de4 ]
This reverts commit 232ccac1bd.
On the subject of suspend, the RISC-V SBI spec states:
This does not cover whether any given events actually reach the hart or
not, just what the hart will do if it receives an event. On PolarFire
SoC, and potentially other SiFive based implementations, events from the
RISC-V timer do reach a hart during suspend. This is not the case for the
implementation on the Allwinner D1 - there timer events are not received
during suspend.
To fix this, the CLOCK_EVT_FEAT_C3STOP (mis)feature was enabled for the
timer driver - but this has broken both RCU stall detection and timers
generally on PolarFire SoC and potentially other SiFive based
implementations.
If an AXI read to the PCIe controller on PolarFire SoC times out, the
system will stall, however, with CLOCK_EVT_FEAT_C3STOP active, the system
just locks up without RCU stalling:
io scheduler mq-deadline registered
io scheduler kyber registered
microchip-pcie 2000000000.pcie: host bridge /soc/pcie@2000000000 ranges:
microchip-pcie 2000000000.pcie: MEM 0x2008000000..0x2087ffffff -> 0x0008000000
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: axi read request error
microchip-pcie 2000000000.pcie: axi read timeout
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
Freeing initrd memory: 7332K
Similarly issues were reported with clock_nanosleep() - with a test app
that sleeps each cpu for 6, 5, 4, 3 ms respectively, HZ=250 & the blamed
commit in place, the sleep times are rounded up to the next jiffy:
== CPU: 1 == == CPU: 2 == == CPU: 3 == == CPU: 4 ==
Mean: 7.974992 Mean: 7.976534 Mean: 7.962591 Mean: 3.952179
Std Dev: 0.154374 Std Dev: 0.156082 Std Dev: 0.171018 Std Dev: 0.076193
Hi: 9.472000 Hi: 10.495000 Hi: 8.864000 Hi: 4.736000
Lo: 6.087000 Lo: 6.380000 Lo: 4.872000 Lo: 3.403000
Samples: 521 Samples: 521 Samples: 521 Samples: 521
Fortunately, the D1 has a second timer, which is "currently used in
preference to the RISC-V/SBI timer driver" so a revert here does not
hurt operation of D1 in its current form.
Ultimately, a DeviceTree property (or node) will be added to encode the
behaviour of the timers, but until then revert the addition of
CLOCK_EVT_FEAT_C3STOP.
Fixes: 232ccac1bd ("clocksource/drivers/riscv: Events are stopped during CPU suspend")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/linux-riscv/YzYTNQRxLr7Q9JR0@spud/
Link: https://github.com/riscv-non-isa/riscv-sbi-doc/issues/98/
Link: https://lore.kernel.org/linux-riscv/bf6d3b1f-f703-4a25-833e-972a44a04114@sholland.org/
Link: https://lore.kernel.org/r/20221122121620.3522431-1-conor.dooley@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48d4180939 ]
In a system with a single initiator node, and one or more memory-only
'target' nodes, the memory-only node(s) would fail to register their
initiator node correctly. i.e. in sysfs:
# ls /sys/devices/system/node/node0/access0/targets/
node0
Where as the correct behavior should be:
# ls /sys/devices/system/node/node0/access0/targets/
node0 node1
This happened because hmat_register_target_initiators() uses list_sort()
to sort the initiator list, but the sort comparision function
(initiator_cmp()) is overloaded to also set the node mask's bits.
In a system with a single initiator, the list is singular, and list_sort
elides the comparision helper call. Thus the node mask never gets set,
and the subsequent search for the best initiator comes up empty.
Add a new helper to consume the sorted initiator list, and generate the
nodemask, decoupling it from the overloaded initiator_cmp() comparision
callback. This prevents the singular list corner case naturally, and
makes the code easier to follow as well.
Cc: <stable@vger.kernel.org>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Liu Shixin <liushixin2@huawei.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Chris Piper <chris.d.piper@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/r/20221116-acpi_hmat_fix-v2-2-3712569be691@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14f16d4756 ]
In hmat_register_target_initiators(), the variable 'best' gets
initialized in the outer per-locality-type for loop. The initialization
just before setting up 'Access 1' targets was unnecessary. Remove it.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Liu Shixin <liushixin2@huawei.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/20221116-acpi_hmat_fix-v2-1-3712569be691@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Stable-dep-of: 48d4180939 ("ACPI: HMAT: Fix initiator registration for single-initiator systems")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d36678f790 ]
Recent changes to the DMA code has resulting in the IMX driver failing
I2C transfers when the buffer has been vmalloc. Only perform DMA
transfers if the message has the I2C_M_DMA_SAFE flag set, indicating
the client is providing a buffer which is DMA safe.
This is a minimal fix for stable. The I2C core provides helpers to
allocate a bounce buffer. For a fuller fix the master should make use
of these helpers.
Fixes: 4544b9f25e ("dma-mapping: Add vmap checks to dma_map_single()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 145900cf91 ]
A problem about i2c-npcm7xx create debugfs failed is triggered with the
following log given:
[ 173.827310] debugfs: Directory 'npcm_i2c' with parent '/' already present!
The reason is that npcm_i2c_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of npcm_i2c can never be created later.
npcm_i2c_init()
debugfs_create_dir() # create debugfs directory
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when platform_driver_register() returns error.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Tali Perry <tali.perry@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit adafbbf689 ]
The STM32 USART can control RS-485 Transmit Enable in hardware. Since
commit 7df5081cbf ("serial: stm32: Add RS485 RTS GPIO control"),
it can alternatively be controlled in software. That was done to allow
RS-485 even if the RTS pin is unavailable because it's pinmuxed to a
different function.
However the commit neglected to deassert Transmit Enable upon invocation
of the ->rs485_config() callback. Fix it.
Avoid forward declarations by moving stm32_usart_tx_empty(),
stm32_usart_rs485_rts_enable() and stm32_usart_rs485_rts_disable()
further up in the driver.
Fixes: 7df5081cbf ("serial: stm32: Add RS485 RTS GPIO control")
Cc: stable@vger.kernel.org # v5.9+
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/6059eab35dba394468335ef640df8b0050fd9dbd.1662886616.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7c7671616 ]
In case the RS485 mode is emulated using GPIO RTS, use the TC interrupt
to deassert the GPIO RTS, otherwise the GPIO RTS stays asserted after a
transmission ended and the RS485 cannot work.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Erwan Le Ray <erwan.leray@foss.st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jean Philippe Romain <jean-philippe.romain@foss.st.com>
Cc: Valentin Caron <valentin.caron@foss.st.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/20220430162845.244655-2-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bcea529b2 ]
Pull out the GPIO RTS enable and disable handling into separate function.
Limit the scope of GPIO RTS toggling only to GPIO emulated RS485 too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Erwan Le Ray <erwan.leray@foss.st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jean Philippe Romain <jean-philippe.romain@foss.st.com>
Cc: Valentin Caron <valentin.caron@foss.st.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/20220430162845.244655-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5082d386e ]
When the kernel receives a route deletion request from user space it
tries to delete a route that matches the route attributes specified in
the request.
If only prefix information is specified in the request, the kernel
should delete the first matching FIB alias regardless of its associated
FIB info. However, an error is currently returned when the FIB info is
backed by a nexthop object:
# ip nexthop add id 1 via 192.0.2.2 dev dummy10
# ip route add 198.51.100.0/24 nhid 1
# ip route del 198.51.100.0/24
RTNETLINK answers: No such process
Fix by matching on such a FIB info when legacy nexthop attributes are
not specified in the request. An earlier check already covers the case
where a nexthop ID is specified in the request.
Add tests that cover these flows. Before the fix:
# ./fib_nexthops.sh -t ipv4_fcnal
...
TEST: Delete route when not specifying nexthop attributes [FAIL]
Tests passed: 11
Tests failed: 1
After the fix:
# ./fib_nexthops.sh -t ipv4_fcnal
...
TEST: Delete route when not specifying nexthop attributes [ OK ]
Tests passed: 12
Tests failed: 0
No regressions in other tests:
# ./fib_nexthops.sh
...
Tests passed: 228
Tests failed: 0
# ./fib_tests.sh
...
Tests passed: 186
Tests failed: 0
Cc: stable@vger.kernel.org
Reported-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Jonas Gorski <jonas.gorski@gmail.com>
Fixes: 493ced1ac4 ("ipv4: Allow routes to use nexthop objects")
Fixes: 6bf92d70e6 ("net: ipv4: fix route with nexthop object delete warning")
Fixes: 61b91eb33a ("ipv4: Handle attempt to delete multipath route when fib_info contains an nh reference")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20221124210932.2470010-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61b91eb33a ]
Gwangun Jung reported a slab-out-of-bounds access in fib_nh_match:
fib_nh_match+0xf98/0x1130 linux-6.0-rc7/net/ipv4/fib_semantics.c:961
fib_table_delete+0x5f3/0xa40 linux-6.0-rc7/net/ipv4/fib_trie.c:1753
inet_rtm_delroute+0x2b3/0x380 linux-6.0-rc7/net/ipv4/fib_frontend.c:874
Separate nexthop objects are mutually exclusive with the legacy
multipath spec. Fix fib_nh_match to return if the config for the
to be deleted route contains a multipath spec while the fib_info
is using a nexthop object.
Fixes: 493ced1ac4 ("ipv4: Allow routes to use nexthop objects")
Fixes: 6bf92d70e6 ("net: ipv4: fix route with nexthop object delete warning")
Reported-by: Gwangun Jung <exsociety@gmail.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d5082d386e ("ipv4: Fix route deletion when nexthop info is not specified")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 692930cc43 ]
I made a stupid typo when adding the nexthop route warning selftest and
added both $IP and ip after it (double ip) on the cleanup path. The
error doesn't show up when running the test, but obviously it doesn't
cleanup properly after it.
Fixes: 392baa339c ("selftests: net: add delete nexthop route warning test")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d5082d386e ("ipv4: Fix route deletion when nexthop info is not specified")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 392baa339c ]
Add a test which causes a WARNING on kernels which treat a
nexthop route like a normal route when comparing for deletion and a
device is specified. That is, a route is found but we hit a warning while
matching it. The warning is from fib_info_nh() in include/net/nexthop.h
because we run it on a fib_info with nexthop object. The call chain is:
inet_rtm_delroute -> fib_table_delete -> fib_nh_match (called with a
nexthop fib_info and also with fc_oif set thus calling fib_info_nh on
the fib_info and triggering the warning).
Repro steps:
$ ip nexthop add id 12 via 172.16.1.3 dev veth1
$ ip route add 172.16.101.1/32 nhid 12
$ ip route delete 172.16.101.1/32 dev veth1
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d5082d386e ("ipv4: Fix route deletion when nexthop info is not specified")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 152fe65f30 ]
When enabled, KASAN enlarges function's stack-frames. Pushing quite a few
over the current threshold. This can mainly be seen on 32-bit
architectures where the present limit (when !GCC) is a lowly 1024-Bytes.
Link: https://lkml.kernel.org/r/20221125120750.3537134-3-lee@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@gmail.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Tom Rix <trix@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d192bec53 ]
PA-RISC uses a much bigger frame size for functions than other
architectures. So increase it to 2048 for 32- and 64-bit kernels.
This fixes e.g. a warning in lib/xxhash.c.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Stable-dep-of: 152fe65f30 ("Kconfig.debug: provide a little extra FRAME_WARN leeway when KASAN is enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 829ae0f81c ]
The issue is reported when removing memory through virtio_mem device. The
transparent huge page, experienced copy-on-write fault, is wrongly
regarded as pinned. The transparent huge page is escaped from being
isolated in isolate_migratepages_block(). The transparent huge page can't
be migrated and the corresponding memory block can't be put into offline
state.
Fix it by replacing page_mapcount() with total_mapcount(). With this, the
transparent huge page can be isolated and migrated, and the memory block
can be put into offline state. Besides, The page's refcount is increased
a bit earlier to avoid the page is released when the check is executed.
Link: https://lkml.kernel.org/r/20221124095523.31061-1-gshan@redhat.com
Fixes: 1da2f328fa ("mm,thp,compaction,cma: allow THP migration for CMA allocations")
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reported-by: Zhenyu Zhang <zhenyzha@redhat.com>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Suggested-by: David Hildenbrand <david@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: William Kucharski <william.kucharski@oracle.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: <stable@vger.kernel.org> [5.7+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89f6c88a6a ]
__isolate_lru_page_prepare() conflates two unrelated functions, with the
flags to one disjoint from the flags to the other; and hides some of the
important checks outside of isolate_migratepages_block(), where the
sequence is better to be visible. It comes from the days of lumpy
reclaim, before compaction, when the combination made more sense.
Move what's needed by mm/compaction.c isolate_migratepages_block() inline
there, and what's needed by mm/vmscan.c isolate_lru_pages() inline there.
Shorten "isolate_mode" to "mode", so the sequence of conditions is easier
to read. Declare a "mapping" variable, to save one call to page_mapping()
(but not another: calling again after page is locked is necessary).
Simplify isolate_lru_pages() with a "move_to" list pointer.
Link: https://lkml.kernel.org/r/879d62a8-91cc-d3c6-fb3b-69768236df68@google.com
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Reviewed-by: Alex Shi <alexs@kernel.org>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stable-dep-of: 829ae0f81c ("mm: migrate: fix THP's mapcount on isolation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bedbbd782 ]
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() for the error path to avoid reference count leak.
Fixes: 2e45528930 ("iommu/vt-d: Unify the way to process DMAR device scope array")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221121113649.190393-3-wangxiongfeng2@huawei.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afca9e19cc ]
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() before 'return true' to avoid reference count leak.
Fixes: 89a6079df7 ("iommu/vt-d: Force IOMMU on for platform opt in hint")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221121113649.190393-2-wangxiongfeng2@huawei.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dominique Martinet
Thinh Nguyen
Tetsuo Handa
Andreas Kemnade
Srinivasa Rao Mandadapu
Filipe Manana
Daniel Díaz
Kees Cook
Konrad Dybcio
GUO Zihua
Shuming Fan
Johan Jonker
Zhichao Liu
Chancel Liu
Giulio Benetti
Tomislav Novak
Jann Horn
Sebastian Reichel
FUKAUMI Naoki
Gaosheng Cui
Uwe Kleine-König
Greg Kroah-Hartman
Linus Torvalds
Zhang Xiaoxu
Jan Dabros
Conor Dooley
Vishal Verma
Andrew Lunn
Yuan Can
Lukas Wunner
Marek Vasut
Ido Schimmel
David Ahern
Nikolay Aleksandrov
Lee Jones
Helge Deller
Gavin Shan
Hugh Dickins
Xiongfeng Wang