* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (88 commits)
powerpc: Fix lwsync feature fixup vs. modules on 64-bit
powerpc: Convert pmc_owner_lock to raw_spinlock
powerpc: Convert die.lock to raw_spinlock
powerpc: Convert tlbivax_lock to raw_spinlock
powerpc: Convert mpic locks to raw_spinlock
powerpc: Convert pmac_pic_lock to raw_spinlock
powerpc: Convert big_irq_lock to raw_spinlock
powerpc: Convert feature_lock to raw_spinlock
powerpc: Convert i8259_lock to raw_spinlock
powerpc: Convert beat_htab_lock to raw_spinlock
powerpc: Convert confirm_error_lock to raw_spinlock
powerpc: Convert ipic_lock to raw_spinlock
powerpc: Convert native_tlbie_lock to raw_spinlock
powerpc: Convert beatic_irq_mask_lock to raw_spinlock
powerpc: Convert nv_lock to raw_spinlock
powerpc: Convert context_lock to raw_spinlock
powerpc/85xx: Add NOR, LEDs and PIB support for MPC8568E-MDS boards
powerpc/86xx: Enable VME driver on the GE SBC610
powerpc/86xx: Enable VME driver on the GE PPC9A
powerpc/86xx: Add MSI section to GE PPC9A DTS
...
Add platform driver support to the pmac-zilog driver, for m68k macs.
Place the powermac-specific code inside #ifdef CONFIG_PPC_PMAC.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Limit the amount of address space claimed for Alchemy serial ports to
0x1000. On the Au1300, ports are only 0x1000 apart, and the registers
only extend to 0x110 at most on all supported alchemy models.
On the Au1300 the autodetect logic no longer works and this makes it
necessary to specify the port type through platform data. Because of
this the MSR quirk needs to be moved outside the autoconfig() function
which will no longer be called when UPF_FIXED_TYPE is specified.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>,
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (187 commits)
sh: remove dead LED code for migo-r and ms7724se
sh: ecovec build fix for CONFIG_I2C=n
sh: ecovec r-standby support
sh: ms7724se r-standby support
sh: SH-Mobile R-standby register save/restore
clocksource: Fix up a registration/IRQ race in the sh drivers.
sh: ms7724: modify scan_timing for KEYSC
sh: ms7724: Add sh_sir support
sh: mach-ecovec24: Add sh_sir support
sh: wire up SET/GET_UNALIGN_CTL.
sh: allow alignment fault mode to be configured at kernel boot.
sh: sh7724: Update FSI/SPU2 clock
sh: always enable sh7724 vpu_clk and set to 166MHz on Ecovec
sh: add sh7724 kick callback to clk_div4_table
sh: introduce struct clk_div4_table
sh: clock-cpg div4 set_rate() shift fix
sh: Turn on speculative return for SH7785 and SH7786
sh: Merge legacy and dynamic PMB modes.
sh: Use uncached I/O helpers in PMB setup.
sh: Provide uncached I/O helpers.
...
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (41 commits)
of: remove undefined request_OF_resource & release_OF_resource
of/sparc: Remove sparc-local declaration of allnodes and devtree_lock
of: move definition of of_chosen into common code.
of: remove unused extern reference to devtree_lock
of: put default string compare and #a/s-cell values into common header
of/flattree: Don't assume HAVE_LMB
of: protect linux/of.h with CONFIG_OF
proc_devtree: fix THIS_MODULE without module.h
of: Remove old and misplaced function declarations
of/flattree: Make the kernel accept ePAPR style phandle information
of/flattree: endian-convert members of boot_param_header
of: assume big-endian properties, adding conversions where necessary
of: use __be32 for cell value accessors
of/flattree: use OF_ROOT_NODE_{SIZE,ADDR}_CELLS DEFAULT for fdt parsing
of/flattree: use callback to setup initrd from /chosen
proc_devtree: include linux/of.h
of: make set_node_proc_entry private to proc_devtree.c
of: include linux/proc_fs.h
of/flattree: merge early_init_dt_scan_memory() common code
of: add 'of_' prefix to machine_is_compatible()
...
Enable/disable automatic hardware flow control as requested by the
termios. The controller does not allow us to control the RTS line when
auto-RTS is enabled, so we enable auto-RTS only if the kernel has not
disabled RTS.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do not ignore the error returned by simple_config() / multi_config().
CC: linux-serial@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Currently the support for MPC5121 PSC UART in the mpc52xx_uart
driver is broken (only console pre-initialized by the bootloader
works). Re-enable it now by providing MPC5121 specific ops
for PSCx clock activation, FIFO controller init/uninit and
MPC5121 PSC FIFO shared interrupt handling functions.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When controlling an industrial radio modem it can be necessary to
manipulate the handshake lines in order to control the radio modem's
transmitter, from userspace.
The transmitter should not be turned off before all characters have been
transmitted. serial8250_tx_empty() was reporting that all characters were
transmitted before they actually were.
===
Discovered in parallel with more testing and analysis by Kees Schoenmakers
as follows:
I ran into an NetMos 9835 serial pci board which behaves a little
different than the standard. This type of expansion board is very common.
"Standard" 8250 compatible devices clear the 'UART_LST_TEMT" bit together
with the "UART_LSR_THRE" bit when writing data to the device.
The NetMos device does it slightly different
I believe that the TEMT bit is coupled to the shift register. The problem
is that after writing data to the device and very quickly after that one
does call serial8250_tx_empty, it returns the wrong information.
My patch makes the test more robust (and solves the problem) and it does
not affect the already correct devices.
Alan:
We may yet need to quirk this but now we know which chips we have a
way to do that should we find this breaks some other 8250 clone with
dodgy THRE.
Signed-off-by: Dick Hollenbeck <dick@softplc.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Kees Schoenmakers <k.schoenmakers@sigmae.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
machine is compatible is an OF-specific call. It should have
the of_ prefix to protect the global namespace.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
Since sci_rxd_in() is used by SCI only, clean up
the header file by killing off code dealing with
SCIF ports and their register definitions.
Also introduce a default sci_rxd_in() function
which can be shared by all SCIF-only processors.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
fmvj18x_cs, serial_cs:
add new id
Panasonic lan & modem card (model name:AL-VML101)
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quirk is applied on all cards with given manfid (is it that correct?).
Unfortunately, that quirk breaks resume on zaurus with billionton
bluetooth card inserted: c950ctrl is 0 and outb() faults.
I believe it is simply not a multiport card. (info->multi == 1). ...
... confirmed by printks.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since UCR1_UARTEN is defined 1, the port was always treated as enabled.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Oskar Schirmer <os@emlix.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabian Godehardt <fg@emlix.com>
Cc: Daniel Glöckner <dg@emlix.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In that situation if the old rate is invalid and the new rate is invalid
and the chip cannot do 9600 baud we report zero, which makes all the
drivers explode.
Instead force the rate based on min/max
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Perform a tricky suspend/resume even with no_console_suspend.
With no_console_suspend, kernel skips serial port suspend/resume and the
serial hardware may remain in undefined state after resume. It actually
happens on devices that don't have BIOS that handle serial
initialization. It makes impossible to use serial console after resume.
Devices affected by this problem include:
Sharp Zaurus devices
Several PXA based ARM embedded boards
The patch does:
- Save the hardware state
- Perform buffer flush in time of its suspend call
- Tell the driver that port is suspended
- But still accept new data
- And keep console hardware in state that allows to send them
It allows to capture late console messages without breaking console
after resume.
This is just a resend of a patch discussed in these threads, as the
patch was not yet applied.
"Possible suspend/resume regression in .32-rc?" (Nov 1-5, 2009, ARM
list, later LKML)
"serial-core: resume serial hardware with no_console_suspend" (Sep
15-Oct 18, 2009, LKML & ARM lists)
Signed-off-by: Stanislav Brabec <sbrabec@suse.cz>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wacom claims that the WACF namespace will always be devoted to serial
Wacom tablets. Remove the existing entries and add a wildcard to avoid
having to update the kernel every time they add a new device.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Move cpu hotplug driver lock from pseries to powerpc
powerpc: Move /proc/ppc64 to /proc/powerpc update
powerpc/8xx: Fix user space TLB walk in dcbX fixup
powerpc: Fix decrementer setup on 1GHz boards
powerpc/iseries: Initialise on-stack completion
powerpc/hvc: Driver build breaks with !HVC_CONSOLE
serial/pmac_zilog: Workaround problem due to interrupt on closed port
powerpc/macintosh: Make Open Firmware device id constant
powerpc: Use helpers for rlimits
powerpc: cpumask_of_node() should handle -1 as a node
powerpc/pseries: Fix dlpar compile warning without CONFIG_PROC_DEVICETREE
powerpc/pseries: Fix xics interrupt affinity
powerpc/swsusp_32: Fix TLB invalidation
powerpc/8xx: Always pin kernel instruction TLB
powerpc: 2.6.33 update of defconfigs for embedded 6xx/7xxx, 8xx, 8xxx
powerpc: Use scripts/mkuboot.sh instead of 'mkimage'
powerpc/5200: update defconfigs
This is a new two finger touch Fujitsu Wacom Tablet PC.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It seems that in qemu, we can see an interrupt in R3 despite the
fact that it's masked in W1. The chip doesn't actually issue an
interrupt, but we can "see" it when taking an interrupt for the
other channel. This may be a qemu bug ... or not, so let's be
safe and avoid calling into the UART layer when that happens which
woulc cause a crash.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Rob Landley <rob@landley.net>
The sh-sci driver used the wrong fifosize for PORT_SCIFA and PORT_SCIF
ports. If an incorrect size is used, the serial core will enforce an
early shutdown on the port, especially with baudrates < 9600.
Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: Ensure ARMv6/7 mm files are built using appropriate assembler options
ARM: Fix wrong dmb
ARM: 5874/1: serial21285: fix disable_irq-from-interrupt-handler deadlock
ARM: 5873/1: ARM: Fix the reset logic for ARM RealView boards
ARM: 5872/1: ARM: include needed linux/cpu.h in asm/cpu.h
ARM: 5871/1: arch/arm: Fix build failure for lpd7a404_defconfig caused by missing includes
ARM: 5870/1: arch/arm: Fix build failure for defconfigs without CONFIG_ISA_DMA_API set
ARM: 5868/1: ARM: fix "BUG: using smp_processor_id() in preemptible code"
ARM: 5867/1: Update U300 defconfig
ARM: 5866/1: arm ptrace: use unsigned types for kernel pt_regs
[ARM] pxa: fix strange characters in zaurus gpio .desc
ARM: add missing recvmmsg syscall number
[ARM] pxa: fix compiler warnings of unused variable 'id' in cpu_is_pxa9*()
[ARM] pxa: update pwm_backlight->notify() to include missed 'struct device *'
[ARM] pxa: enable L2 if present in XSC3
[ARM] pxa: do not enable L2 after MMU is enabled
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
sky2: Fix oops in sky2_xmit_frame() after TX timeout
Documentation/3c509: document ethtool support
af_packet: Don't use skb after dev_queue_xmit()
vxge: use pci_dma_mapping_error to test return value
netfilter: ebtables: enforce CAP_NET_ADMIN
e1000e: fix and commonize code for setting the receive address registers
e1000e: e1000e_enable_tx_pkt_filtering() returns wrong value
e1000e: perform 10/100 adaptive IFS only on parts that support it
e1000e: don't accumulate PHY statistics on PHY read failure
e1000e: call pci_save_state() after pci_restore_state()
netxen: update version to 4.0.72
netxen: fix set mac addr
netxen: fix smatch warning
netxen: fix tx ring memory leak
tcp: update the netstamp_needed counter when cloning sockets
TI DaVinci EMAC: Handle emac module clock correctly.
dmfe/tulip: Let dmfe handle DM910x except for SPARC on-board chips
ixgbe: Fix compiler warning about variable being used uninitialized
netfilter: nf_ct_ftp: fix out of bounds read in update_nl_seq()
mv643xx_eth: don't include cache padding in rx desc buffer size
...
Fix trivial conflict in drivers/scsi/cxgb3i/cxgb3i_offload.c
The console hangs during bootup when disable_irq is called from the
transmit interrupt handler (it will wait forever for it's "own"
interrupt in synchronize_irq). Fix by using disable_irq_nosync()
instead.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pcnet_cs,serial_cs:
add cis of KTI PE520 pcmcia network card,
and serial card(Sierra Wireless AC860).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
ctrl_xxx() is an antiquated SH interface, while __raw_xxx is the standard
API that accomplishes the same thing. As such, this converts the
remaining sh-sci straggles over, which enables the driver to be wired up
for ARM SH-Mobile CPUs as well.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This establishes a sensible max baud rate for the earlyprintk cases where
the port's uartclk has not yet been determined.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (33 commits)
sh: Fix test of unsigned in se7722_irq_demux()
sh: mach-ecovec24: Add FSI sound support
sh: mach-ecovec24: Add mt9t112 camera support
sh: mach-ecovec24: Add tw9910 support
sh: MSIOF/mmc_spi platform data for the Ecovec24 board
sh: ms7724se: Add ak4642 support
sh: Fix up FPU build for SH5
sh: Remove old early serial console code V2
sh: sh5 scif pdata (sh5-101/sh5-103)
sh: sh4a scif pdata (sh7757/sh7763/sh7770/sh7780/sh7785/sh7786/x3)
sh: sh4a scif pdata (sh7343/sh7366/sh7722/sh7723/sh7724)
sh: sh4 scif pdata (sh7750/sh7760/sh4-202)
sh: sh3 scif pdata (sh7705/sh770x/sh7710/sh7720)
sh: sh2a scif pdata (sh7201/sh7203/sh7206/mxg)
sh: sh2 scif pdata (sh7616)
sh-sci: Extend sh-sci driver with early console V2
sh: Stub in P3 ioremap support for nommu parts.
sh: wire up vmallocinfo support in ioremap() implementations.
sh: Make the unaligned trap handler always obey notification levels.
sh: Couple kernel and user write page perm bits for CONFIG_X2TLB
...
Two IOC3 and IOC4 drivers have broken error paths on registration. Fix
them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several IOC3 and IOC4 drivers misuse the __devinit and __devexit section
markers. Use __init and __exit instead as appropriate, then add __devinit
and __devexit where they really belong for PCI drivers.
Also make ioc4_serial_init static.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Pat Gefre <pfg@sgi.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is V2 of early serial console support for the sh-sci
driver. The early serial console is using early platform
devices and "earlyprintk". To use this feature the early
platform devices must be broken out to one device per port
and the desired port should be selected on the kernel command
line like: "earlyprintk=sh-sci.N[,baudrate][,keep]"
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (58 commits)
tty: split the lock up a bit further
tty: Move the leader test in disassociate
tty: Push the bkl down a bit in the hangup code
tty: Push the lock down further into the ldisc code
tty: push the BKL down into the handlers a bit
tty: moxa: split open lock
tty: moxa: Kill the use of lock_kernel
tty: moxa: Fix modem op locking
tty: moxa: Kill off the throttle method
tty: moxa: Locking clean up
tty: moxa: rework the locking a bit
tty: moxa: Use more tty_port ops
tty: isicom: fix deadlock on shutdown
tty: mxser: Use the new locking rules to fix setserial properly
tty: mxser: use the tty_port_open method
tty: isicom: sort out the board init logic
tty: isicom: switch to the new tty_port_open helper
tty: tty_port: Add a kref object to the tty port
tty: istallion: tty port open/close methods
tty: stallion: Convert to the tty_port_open/close methods
...
Do not read IIR in serial8250_start_tx when UART_BUG_TXEN
Reading the IIR clears some oustanding interrupts so it is not safe.
Instead, simply transmit immediately if the buffer is empty without
regard to IIR.
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Intel(R) PXA27x Processor Family Specification Update (Nov 2005)
says:
E75. UART: Baud rate may not be programmed correctly on
back-to-back writes.
Problem:
When programming the Divisor Latch registers, Low and High (DLL and
DLH), with back-to-back writes, the second register write may not
take effect. The result is an incorrect baud rate.
Workaround:
After programming the first Divisor Latch register, read and verify
it before programming the second Divisor Latch register.
This was hit when changing the baud rate from 115200 to 9600 while
receiving characters at 9600 Bd.
And fixed indention of some comments nearby.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding EEH handlers for the serial jsm driver. This patch adds
the PCI error handlers and also register them to be called when
a error is detected.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Scott Kilau <scottk@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently there is a field in the jsm_board structure to cont
the number of interrupt that the card recevived, but it's not
working properly when the IRQ line is shared, and also nowhere
else this field is used. So, This patch is removing it.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <Scott.Kilau@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds
Finn Thain
Manuel Lauss
Benjamin Herrenschmidt
Russell King
Rabin Vincent
Dominik Brodowski
Anatolij Gustschin
Dick Hollenbeck
Grant Likely
Magnus Damm
Richard Röjfors
Ken Kawasaki
Pavel Machek
Roel Kluin
Alan Cox
Stanislav Brabec
Matthew Garrett
Ping
Markus Pietrek
Simon Kagstrom
Paul Mundt
Jean Delvare
Alexey Dobriyan
Ian Jackson
Uwe Kleine-König
André Goddard Rosa
Breno Leitao