Add support for computing a combined accelerator/brake axis for wheels
which don't contain combined data in their HID stream.
This includes DFGT, G25, G27, G29 and Wii-Wheel.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for reporting a combined accelerator/brake axis for wheels
which contain combined data in their HID stream.
This includes DF, MOMO, MOMO2 and DFP.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Introduce a dev_attr which can be used to combine the accelerator
and brake pedals into a single axis. This is useful for older games
which can not handle seperate accelerator and brake.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Update the copyright notice with the current year and add a note
about values for controlling the Dualshock 4 reporting rate.
Processing reports at the default full rate of 1000hz can be too
demanding for some low-power embedded processors so noting
alternate values for people working with this hardware can be useful.
Thanks to Rostislav Pehlivanov for finding these values.
Signed-off-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When initially connected via USB the Sixaxis isn't fully initialized
until the PS logo button is pressed and won't send any input reports
nor will any state set by output reports be retained.
This adds a 'defer_initialization' flag to the sony_sc struct which,
when set, will delay sending any output reports until the first input
report has arrived. This flag is used with the USB Sixaxis to ensure
that any state sent will persist since, until the PS button is pushed,
any changes sent to the controller via an output report will be lost
after a couple of seconds.
The initial state of the controller is still configured at the time
of the initial connection and won't be internally modified after that,
so any state set by the user between that time and the recepit of the
first input report won't be lost.
Signed-off-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some USB-only devices which masquerade as Sixaxis controllers report the
same generic Bluetooth address for all hardware when queried via the HID
report. This causes these devices to be wrongly rejected as duplicates
when more than one is connected at once.
This introduces a connection type comparison when checking for duplicates
and only rejects the newly connected device if the existing matching
device is connected using a different connection protocol.
The results of the connection type comparison are also used when
registering power supply info as the device Bluetooth address is used
as the unique identifier string. In cases where more than one valid
device has the same Bluetooth address the device ID is now appended
to the power supply name string to avoid name collisions when
registering the power supply information.
Signed-off-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 3ccc60f9d8.
While investigating bug https://bugzilla.kernel.org/show_bug.cgi?id=37982 ,
there was solid evidences that Microsoft reused the same report
descriptor for the its Digital Media keyboard series.
Since 1989dad "HID: input: ignore System Control application usages if not
System Controls", the keyboard series do not produce a spurious joystick
input device inode without needing to patch the problematic report
descriptor. As such the MS_RDESC_3K reportdescriptor fixup can be removed.
Signed-off-by: Michel Hermier <michel.hermier@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
While at it, remove redundant input_free_device(NULL) call.
[jkosina@suse.cz: ammend changelog]
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The stick device does not work after resume, add U1_SP_ABS_MODE flag can
make the device work after resume.
This has been discovered by pure guesswork, based on how the existing code uses
U1_TP_ABS_MODE flag on both initialization and resume.
I also tested the the patch on an ALPS touchpad without stick device, did not
notice any side effect on suspend/resume, so I made the U1_SP_ABS_MODE flag
mandatory.
[jkosina@suse.cz: made changelog more verbose]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add quirk for Corsair STRAFE keyboard, similarly to what we've been
doing for other CORSAIR devices already, in order to avoid long delays
during boot.
[jkosina@suse.cz: reword changelog a little bit]
Signed-off-by: Marian Krivos <marian.krivos@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A kfree(readbuf) call was missed if hid_hw_raw_request() fails, fix it.
Also avoid mixing direct return with goto in the error paths.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for the third version of UC-Logic TWHA60, which has
three interfaces and responds to initialization.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make uclogic_report_fixup override constant descriptors with generated
descriptors, so models reusing product ID, but working with generated
descriptor get correct one.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add partial support for the UGTizer GP0610 tablet (aka iBall PF1064U,
aka UGTizer GT1060) to the hid-uclogic.c driver.
The pen input is supported fully, but frame buttons and wheel don't work
yet.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on a patch from: Nikolai Kondrashov <Nikolai.Kondrashov@redhat.com>
Enable abstract keyboard mode for Huion tablets, which makes them report
frame buttons using the pen interface and report ID. Divert these
reports to a virtual report ID describing them.
This makes the tablet compatible with xf86-input-wacom and libinput,
but stops the frame buttons from reporting keyboard events.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove unnecessary allocation failure messages from hid-uclogic.c,
following the checkpatch.pl recommendations.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a dedicated, fixed report descriptor for the second version of KYE
MousePen i608X graphics tablet. The descriptor fixes pressure and
drawing area ranges.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rename the device ID macro for the second version of KYE MousePen i608x
graphics tablet to have "V" in its name to signify that "2" is a
version.
I.e. USB_DEVICE_ID_KYE_MOUSEPEN_I608X_2 ->
USB_DEVICE_ID_KYE_MOUSEPEN_I608X_V2
This also makes applying additional fixes from DIGImend easier.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove comments with broken links to tablet descriptions from
hid-kye/uclogic/waltop drivers.
They pointed to now dead DIGImend project wiki at sf.net. Even though
the DIGImend project still hosts descriptions, now at
digimend.github.io, it's better to avoid them going stale again, and let
anyone interested search the web instead.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Microsoft is reusing its report descriptor again and again, and part of it
looks like this:
0x05, 0x01, // Usage Page (Generic Desktop) 299
0x09, 0x80, // Usage (System Control) 301
0xa1, 0x01, // Collection (Application) 303
0x85, 0x03, // Report ID (3) 305
0x19, 0x00, // Usage Minimum (0) 307
0x29, 0xff, // Usage Maximum (255) 309
0x15, 0x00, // Logical Minimum (0) 311
0x26, 0xff, 0x00, // Logical Maximum (255) 313
0x81, 0x00, // Input (Data,Arr,Abs) 316
0xc0, // End Collection 318
While there is nothing wrong in term of processing, we do however blindly
map the full usage range (it's an array) from 0x00 to 0xff, which creates
some interesting axis, like ABS_X|Y, and a bunch of ABS_MISC + n.
While libinput and other stacks don't care that much (we can detect them),
joydev is very happy and attaches itself to the mouse or keyboard.
The problem is that joydev now handles the device as a joystick, but given
that we have a HID array, it sets all the ABS_* values to 0. And in its
world, 0 means -32767 (minimum value), which sends spurious events to games
(think Steam).
It looks like hid-microsoft tries to tackle the very same problem with its
.report_fixup callback. But fixing the report descriptor is an endless task
and is quite obfuscated.
So take the hammer, and decide that if the application is meant to be
System Control, any other usage not in the System Control range should
be ignored.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1325354
Link: https://bugzilla.kernel.org/show_bug.cgi?id=28912
Link: https://github.com/ValveSoftware/steam-for-linux/issues/3384
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1325354
Link: https://bugzilla.kernel.org/show_bug.cgi?id=37982
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many modules call misc_register and misc_deregister in its module init
and exit methods without any additional code. This ends up being
boilerplate. This patch adds helper macro module_misc_device(), that
replaces module_init()/ module_exit() with template functions.
This patch also converts drivers to use new macro.
Change since v1:
Add device.h include in miscdevice.h as module_driver macro was not
available from other include files in some architectures.
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use kzalloc rather than kmalloc followed by memset with 0.
Generated by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adding support for the Microsoft Surface 4 Type Cover Pro (JP).
Signed-off-by: Yuta Kobayashi <alu.ula@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Need enum quirk to change the base of enums to 1 for
power and report descriptors.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver is responsible for implementing ISH HID client, which
gets HID description and report. Once it has completely gets
report descriptors, it registers as a HID LL drivers. This implements
necessary callbacks so that it can be used by HID sensor hub driver.
Original-author: Daniel Drubin <daniel.drubin@intel.com>
Reviewed-and-tested-by: Ooi, Joyce <joyce.ooi@intel.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Rann Bar-On <rb6@duke.edu>
Tested-by: Atri Bhattacharya <badshah400@aim.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This layer is responsible for
- Enumerating over PCI bus
- Inform FW about host readiness
- Provide HW interface to transport layer for control and messages
- Interrupt handling and routing
Original-author: Daniel Drubin <daniel.drubin@intel.com>
Reviewed-and-tested-by: Ooi, Joyce <joyce.ooi@intel.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Rann Bar-On <rb6@duke.edu>
Tested-by: Atri Bhattacharya <badshah400@aim.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ISH transport layer (ishtp) is a bi-directional protocol implemented
on the top of PCI based inter processor communication layer. This layer
offers:
- Connection management
- Flow control with the firmware
- Multiple client sessions
- Client message transfer
- Client message reception
- DMA for RX and TX for fast data transfer
Refer to Documentation/hid/intel-ish-hid.txt for
overview of the functionality implemented in this layer.
Original-author: Daniel Drubin <daniel.drubin@intel.com>
Reviewed-and-tested-by: Ooi, Joyce <joyce.ooi@intel.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Rann Bar-On <rb6@duke.edu>
Tested-by: Atri Bhattacharya <badshah400@aim.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a touchscreen contains both multitouch and single-touch reports in its
descriptor in that order, the driver may overwrite information it saved
about the format of the multitouch report. This can cause the report
processing code to get tripped up and send an incorrect event stream to
userspace.
In particular, this can cause last_slot_field to be overwritten with the
result that the driver prematurely assumes it has finished processing a
slot and sending the ABS_MT_SLOT event at the wrong point in time,
associating events for the current contact with the following contact
instead.
To prevent this from occurring, we update the value of last_slot_field
durring the pre_report phase to ensure that it is correct for the report
that is to be processed.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Touch arbitration is always on in wacom.ko. However, there are
touch enabled applications use both pen and touch simultaneously.
We should provide an option for userland to decide if they want
arbitration on or off.
This patch sets default touch_arbitration to on since most userland
apps are not ready to process pen and touch events simultaneously.
In the future, when userland is ready to accept pen and touch events
together, we will switch default touch_arbitration to off.
Tested-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'oVid' and 'oPid' variables used by wacom_are_sibling are a hacky
solution to the problem of the driver historically having few good
heuristics to use in determining if two devices should be considered
siblings or not. While it works well enough for explicitly supported
devices, it offers no help for HID_GENERIC devices. Now that we have
a bit more information (e.g. direct/indirect) available to us though,
we should make use of it it to improve the pairing of such devices.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
"Direct" input devices like Cintiqs and Tablet PCs set the INPUT_PROP_DIRECT
property to notify userspace that the sensor and screen are overlaid. This
information can also be useful elsewhere within the kernel driver, however,
so we introduce a new WACOM_DEVICETYPE_DIRECT that signals this to other
kernel code.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of displaying a generic "tablet", now g-c-c shows a pretty
"Wacom Intuos Pro S (WL)".
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like upowerd is ignoring this since October 2013, so there is
no need to keep this around in the kernel.
And as mentioned in 8aaa592 (linux: Ignore ACs coming from devices) in
the upower tree, "We already have enough information on the device
battery".
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When upowerd detects a new device, it tries to map this new device to
an input to guess its kind. It works OK for wired tablets when the
wireless module and its battery are attached, but not so well when
connected over wireless.
In that case, the battery is attached to the wireless HID node, not
the Pen or Pad HID node. So there is no input node as a parent of the
reported battery, which means it will be showed as a computer battery
in gnome-control-center.
If we set the power supply type to USB, upowerd has a heuristic that
detects "wacom_" in the name of the power_supply, and set the type to
tablet. So it's now clear that the reported battery of from a tablet.
(see https://cgit.freedesktop.org/upower/tree/src/linux/up-device-supply.c)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 24HD has 1 button per LED (first three buttons of each group).
We need a special treatment for them as it's not a uniq button that
switches between the LEDs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The code for 21UX2 and 24HD makes the LED group 1 on the left, and
the group 0 on the right. The buttons are ordered in the other way,
but libwacom already exports those that way. So we simply can't reassign
LED group 0 to the left buttons, and have to quirk the incoming data...
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The EKR switches the LED directly, and there is no point in having
userspace handling the switch it self when it's easy enough to do
in the kernel.
The other benefit is that now userspace does not need to have root access
to the LED but need only to read them with user privileges.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a bug (?) in devm_led_classdev_register() in which its increments
the refcount of the parent. If the parent is an input device, that means
the ref count never reaches 0 when devm_input_device_release() gets called.
This means that the LEDs and all the devres resources attached to the
input device are not released.
Manually force the release of the group so that the leds are released once
we are done using them.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The now obsolete sysfs files for LEDs and EKRemote are kept for backward
compatibility.
Both the EKR (read-only) and the regular Cintiqs and Intuos are now
sharing the same led API.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Or Gnome complains about an empty battery.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously, all the remotes attached to the same receiver would share the
same power_supply. That's not good as the remotes will constantly change
the battery information according to their own state.
To have something generic enough, we introduce struct wacom_battery
which regroups all the information we need for a battery.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Thanks to devres, we can now afford to create more than one input node
without having to overload the remove/failure paths. Having one input
node per remote is something which should have been implemented from start
but the probability of having users with several remotes is quite low.
Anyway, still, better looking at the future and implement things properly.
Remote input nodes will be freed/unregistered magically as they are
created in the devres group &remote->remotes[index].
We need to open the hid node now that the remotes are dynamically
allocated.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
No functional changes, just a prep patch for the one after.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This will be useful when each remote will be assigned its own input device.
We won't need to unregister each input and sysfs and other elements one
at a time.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wacom_remote_create_attr_group() and wacom_remote_destroy_attr_group()
functions were both allocating/destroying the sysfs groups but also
initializing the parameters for the remotes. Have proper functions
that can be called and extended.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Thanks to devres management, we don't need to remember a lot of failure
path. One or two is enough.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If we want to have one input device per remote, it's better to have our
own struct wacom_remote which is dynamically allocated.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wacom_remote_status_irq() sends information of addition/removal of EKR.
We want to allocate one input node per remote, so better having this
in a separate worker, not handled in the IRQ directly.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We need to add an action to ensure wacom->led.groups is null when
wacom_led_control() gets called after the resources has been freed.
This also prevents to send a LED command when there is no support
from the device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wacom_release_shared_data() and wacom_remove_shared_data() are moved up
so they can be referenced in wacom_add_shared_data().
There is no point in explicitly setting wacom_wac1->shared->type to 0 in
wacom_wireless_work() (plus this would give an oops).
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We started switching the driver to devres, so we should use it as much
as possible.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The sysfs group was indeed removed by kobject_put(wacom->remote_dir) in
wacom_remove(), but the name of the group was never freed.
Also remove the misplaced kobject_put(wacom->remote_dir) in the error
path of wacom_remote_create_attr_group().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use our own wacom_devm_sysfs_create_group() as there is currently no
generic one. It has been requested at least twice [1][2] but has been
always rejected.
However, in the Wacom case, for the wirelessly connected devices, we need
to be able to release the created sysfs files without removing the parent
kobject.
[1] https://patchwork.kernel.org/patch/7526551/
[2] https://lkml.org/lkml/2013/3/14/728
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We currently have a complex clean_inputs() function while this can be
handled all by devres. Set a group that we can destroy in wireless_work().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplifying the error code paths.
We need to keep wacom_clean_inputs() around for now as the wireless
module is using it to dynamically remove the inputs on disconnect.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplifying the error code paths.
We need to keep wacom_destroy_battery() around for now as the wireless
module and the remotes are using it to dynamically remove the battery
supply on disconnect.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like the battery hijacked the wireless worker. That's not fair so
use a work queue per task.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Like remotes, LEDs should be handled by themself, not magically behind
the inputs as they have a complete different life.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wacom->remote_dir has nothing to do with inputs, so better not magically
removing it when cleaning inputs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The type is never set but we check for it in wacom_wireless_irq().
It looks like this is a big hack from the beginning, so fill in the gap
only.
Untested.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since fd5f92b ("HID: wacom: reuse wacom_parse_and_register() in
wireless_work"), wacom->shared->type is not set.
Send the information of the battery if we have one.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The new device has 06a3:0cfa as identifiers, and the same quirks as the
other RAT models. It needs this fix in order not to confuse the xorg server
with its tristate button, which is reported as three different buttons, one
of which is always on.
[jkosina@suse.cz: drop unrelated whitespace hunk]
Signed-off-by: Mayeul Cantan <mayeul.cantan@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The FutureMax Dance Mat claims to be a SixAxis controller
but breaks if descriptor fixups are applied. Detect the
device using its USB product string and disable fixups
when it is detected.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
USB device
Vendor 05ac (Apple)
Device 0267 (Magic Keyboard)
This keyboard supports both Bluetooth and USB connections, this patch
only covers USB.
Thanks to Maxime Poulin <maxpoulin64@gmail.com>
Signed-off-by: Jean-Gabriel Gill-Couture <jeangab@jeangab.fr.nf>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Properly handle this __le16 value on big endian systems.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for Greynut Luxafor. This device has two groups of three
independent LED's each.
Successfully tested with such a device.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for the HID-compliant Delcom Visual Signal Indicator
generation 2 devices.
Successfully tested with part no 904000 from the family of these devices.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Delcom uses the report id to submit command information. To be able to
use the hidled framework also for Delcom devices we have to remove the
report id from struct hidled_config.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The usage Confidence is mandary to Windows Precision Touchpad devices. If
it is examined in input_mapping on a WIndows Precision Touchpad, a new add
quirk MT_QUIRK_CONFIDENCE desgned for such devices will be applied to the
device. A touch with the confidence bit is not set is determined as
invalid.
Tested on Dell XPS13 9343
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org> # XPS 13 9350, BIOS 1.4.3
Signed-off-by: Allen Hung <allen_hung@dell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 25a84db15b ("HID: multitouch: enable palm rejection
if device implements confidence usage")
The commit enables palm rejection for Win8 Precision Touchpad devices but
the quirk MT_QUIRK_VALID_IS_CONFIDENCE it is using is not working very
properly. This quirk is originally designed for some WIn7 touchscreens. Use
of this for a Win8 Precision Touchpad will cause unexpected pointer jumping
problem.
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org> # XPS 13 9350, BIOS 1.4.3
Signed-off-by: Allen Hung <allen_hung@dell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch validates the num_values parameter from userland during the
HIDIOCGUSAGES and HIDIOCSUSAGES commands. Previously, if the report id was set
to HID_REPORT_ID_UNKNOWN, we would fail to validate the num_values parameter
leading to a heap overflow.
Cc: stable@vger.kernel.org
Signed-off-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove an unnecessary codes.
Change input_ivent() function to appropriate function.
Add the device ID of "HID_DEVICE_ID_ALPS_U1_DUAL".
[jkosina@suse.cz: removed unnecessary bitshifts of values passed
input_report_key() as spotted by Dmitry]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that support for ThingM blink(1) was merged into the hid-led driver
the dedicated driver for this device can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for ThingM blink(1) and make the dedicated ThingM driver
obsolete.
Successfully tested with a blink(1) mk2.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add i2c_hid_shutdown for i2c-hid driver to send suspend cmd & free
irq before device shutdown.
Some HW design (i.e. Umaro, a chromebook model) is that the power to
i2c hid device won't down after device shutdown. Also the i2c-hid driver
do not send suspend cmd to the hid i2c device and free its irq before
shutdown.So if We touch the touchscreen or some other i2c hid device,
the power consumtion will be go up even when the device is in shutdown
state.
Though the root cause maybe a HW issue. But it seems that it is a
good pratice to set power sleep for i2c-hid device before shutdown.
Signed-off-by: Guohua Zhong <ghzhong@yifangdigital.com>
Acked-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All devices with ALPS_JP VID are handled by hid-alps driver, hence they require
an entry in hid_have_special_driver[].
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Kernel printf format %*ph allows to print small buffers up to 64 bytes.
Make use of it to simplify the debug output code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Calculating size of the report as sizeof(pointer) always passess the length
corresponding to the pointer type, not the underlying data report.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The driver port was done carefully not to depend on USB at all, in favor of
being generic HID driver instead. Therefore there is no need to explicitly
talk about USB only in the config.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch migrates the USB LED driver to the HID subsystem.
Supported are Dream Cheeky Webmail Notifier / Friends Alert
and Riso Kagaku Webmail Notifier.
Benefits:
- Avoid using USB low-level calls and use the HID subsystem instead
(as this device provides a USB HID interface)
- Use standard LED subsystem instead of proprietary sysfs entries,
this allows e.g. to use the device with features like triggers
Successfully tested with a Dream Cheeky Webmail Notifier and a
Riso Kagaku Webmail Notifier compatible device.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
i2c-hid devices' suspend/resume are usually time-consuming process.
For example, the touch controller(i2c-ATML1000:00) on ASUS T100 tablet
takes about 160ms for suspending and 120ms for resuming. This patch
enables i2c-hid devices to suspend/resume asynchronously. This will
take advantage of multicore and speed up system suspend/resume process.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many devices use userspace bluetooth stacks like BlueZ or Bluedroid in combination
with uhid. If any of these stacks is used with a HID device for which the driver
performs a HID request as part .probe (or technically another HID operation),
this results in a deadlock situation. The deadlock results in a 5 second timeout
for I/O operations in HID drivers, so isn't fatal, but none of the I/O operations
have a chance of succeeding.
The root cause for the problem is that uhid only allows for one request to be
processed at a time per uhid instance and locks out other operations. This means
that if a user space is creating a new HID device through 'UHID_CREATE', which
ultimately triggers '.probe' through the HID layer. Then any HID request e.g. a
read for calibration data would trigger a HID operation on uhid again, but it
won't go out to userspace, because it is still stuck in UHID_CREATE.
In addition bluetooth stacks are typically single threaded, so they wouldn't be
able to handle any requests while waiting on uhid.
Lucikly the UHID spec is somewhat flexible and allows for fixing the issue,
without breaking user space. The idea which the patch implements as discussed
with David Herrmann is to decouple adding of a hid device (which triggers .probe)
from UHID_CREATE. The work will kick off roughly once UHID_CREATE completed (or
else will wait a tiny bit of time in .probe for a lock). A HID driver has to call
HID to call 'hid_hw_start()' as part of .probe once it is ready for I/O, which
triggers UHID_START to user space. Any HID operations should function now within
.probe and won't deadlock because userspace is stuck on UHID_CREATE.
We verified this patch on Bluedroid with Android 6.0 and on desktop Linux with
BlueZ stacks. Prior to the patch they had the deadlock issue.
[jkosina@suse.cz: reword subject]
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The firmware found in the touch screen of an SP3 is buggy and may miss
to send lift off reports for contacts. Try to work around that issue by
using MT_QUIRK_NOT_SEEN_MEANS_UP.
based on a patch from: Daniel Martin <consume.noise@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Flushing a work that reschedules itself is not a sensible operation. It needs
to be killed. Failure to do so leads to a kernel panic in the timer code.
CC: stable@vger.kernel.org
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 7e12978 ("HID: wacom: break out wacom_intuos_get_tool_type") by accident
removed stylus_in_proximity flag for Intuos series while shuffling the code
around.
Fix that by reintroducing that flag setting in wacom_intuos_inout(), where
it originally was.
Fixes: 7e12978 ("HID: wacom: break out wacom_intuos_get_tool_type")
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The fuzz present on the distance and tilt axes is noticable when a puck is
present, and userspace (specifically libinput) would like the ability to
filter out the noise. To facilitate this, we assign a fuzz value of '1'
for the distance and tilt axes. This is large enough to cover most of the
natural variation in distance value as the puck is moved around, and
enough to cover the jitter in rotation (reported through tilt axes) when
the puck is left alone.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These devices feature multiple interfaces/endpoints: a legacy BIOS/boot
interface (endpoint 0x81), as well as 2 corsair-specific keyboard interfaces
(endpoint 0x82, 0x83 IN/0x03 OUT) and an RGB LED control interface (endpoint
0x84 IN/0x04 OUT)
Because the extra 3 interfaces are not of subclass USB_INTERFACE_SUBCLASS_BOOT,
HID_QUIRK_NOGET is not automatically set on them and a 10s timeout per-endpoint
(30s per device) occurs initialising reports on boot. We configure
HID_QUIRK_NO_INIT_REPORTS for these devices.
Additionally the left-side G1-G18 macro keys on the K95RGB generate output on
the un-opened 0x82/0x83 endpoints which causes the keyboard to stop responding
waiting for this event to be collected. We enable HID_QUIRK_ALWAYS_POLL to
prevent this situation from occurring.
Signed-off-by: Trent Lloyd <trent@lloyd.id.au>
Tested-by: SUGNIAUX Wilfried <wsu@ppharm2k20.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Needed for v2 of the device firmware, otherwise kernel will stuck for few
seconds and throw "usb_submit_urb(ctrl) failed: -1" early on system boot.
Signed-off-by: Nazar Mokrynskyi <nazar@mokrynskyi.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
LED core takes care of handling failed calls to thingm_let_set.
- print error message in set_brightness_delayed or
- pass error to caller in led_set_brightness_sync
Also the error message here doesn't provide any hint what actually
went wrong. Therefore remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@rehat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use recently introduced flag LED_HW_PLUGGABLE to avoid warnings when
the device is unplugged.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- fix for how scaling linearization is computed in wiimote driver, by
Cyan Ogilvie
- endless retry loop fix in generic USB HID core reset-resume handling,
by Alan Stern
- two functional fixes affecting particular devices, and oops fix for
wacom driver, by Jason Gerecke
- multitouch slot numbering fix from Gabriele Mazzotta
- a couple more small fixes on top
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: Support switching from vendor-defined device mode on G9 and G11
HID: wacom: Initialize hid_data.inputmode to -1
HID: microsoft: add support for 3 more devices
HID: multitouch: Synchronize MT frame on reset_resume
HID: wacom: fix Bamboo ONE oops
HID: lenovo: Don't use stack variables for DMA buffers
HID: usbhid: fix inconsistent reset/resume/reset-resume behavior
HID: wiimote: Fix wiimote mp scale linearization
The 'size' variable is not really needed, and we can also shift constant
in the loop body when masking off existing bits.
Also we do not have to use 64 bit calculations if we take an extra
branch.
[jkosina@suse.cz: fix a small error in changelog]
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A tablet PC booted into Windows may have its pen/touch hardware switched
into "Wacom mode" similar to what we do with explicitly-supported hardware.
Some devices appear to maintain this state across reboots, preventing their
use with the generic HID driver. This patch adds support for detecting the
presence of the mode switch feature report used by devices based on the G9
and G11 chips and has the HID codepath always attempt to reset the device
back to sending standard HID reports.
Fixes: https://sourceforge.net/p/linuxwacom/bugs/307/
Fixes: https://sourceforge.net/p/linuxwacom/bugs/310/
Fixes: https://github.com/linuxwacom/input-wacom/issues/15
Co-authored-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 5ae6e89 introduced hid_data.inputmode with a comment that it
would have the value -1 if undefined, but then forgot to actually
perform the initialization. Although this doesn't appear to have
caused any problems in practice, it should still be remedied.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for the Micrsift Digital 4K, Media 600 and Media 3000 V1 Keyboards,
which have the same quirks as the already existing hardware MS_NE4K.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=52841
[jkosina@suse.cz: rephrase changelog]
Signed-off-by: Alistair Leslie-Hughes <leslie_alistair@hotmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Asus X205TA and E200HA built-in keyboard contain wrong logical maximum value in
report descriptor.
This patch correct wrong logical maximum in report descriptor.
Signed-off-by: Yusuke Fujimaki <usk.fujimaki@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
My static checker complains that "devid" can be uninitialized if
alloc_chrdev_region() fails. Fix this by moving the error hanling
forward a couple lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
My static checker complains because we use "dev_id" before we check for
errors so it could be uninitialized. Fix this by moving the error
handling forward a couple lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
input_mt_get_slot_by_key() requires input_mt_sync_frame() to be called
at each frame. Do it when releasing the touches, or else we won't get
a proper slot number after mt_reset_resume().
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Benjamin TIssoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like recent changes in the Wacom driver made the Bamboo ONE crashes.
The tablet behaves as if it was a regular Bamboo device with pen, touch
and pad, but there is no physical pad connected to it.
The weird part is that the pad is still sending events and given that
there is no input node connected to it, we get anull pointer exception.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1317116
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The lenovo_send_cmd_cptkbd function uses a stack variable to submit
commands via hid_hw_raw_request. Eventually this gets to the
usb_hcd_map_urb_for_dma function, which causes a warning to be thrown
if the CONFIG_DMA_API_DEBUG option is enabled.
Fix this by allocating a temporary buffer instead.
[jkosina@suse.cz: no need to NULL-initialize buf, spotted by Benjamin]
Reported-by: lejeczek <peljasz@yahoo.co.uk>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The usbhid driver has inconsistently duplicated code in its post-reset,
resume, and reset-resume pathways.
reset-resume doesn't check HID_STARTED before trying to
restart the I/O queues.
resume fails to clear the HID_SUSPENDED flag if HID_STARTED
isn't set.
resume calls usbhid_restart_queues() with usbhid->lock held
and the others call it without holding the lock.
The first item in particular causes a problem following a reset-resume
if the driver hasn't started up its I/O. URB submission fails because
usbhid->urbin is NULL, and this triggers an unending reset-retry loop.
This patch fixes the problem by creating a new subroutine,
hid_restart_io(), to carry out all the common activities. It also
adds some checks that were missing in the original code:
After a reset, there's no need to clear any halted endpoints.
After a resume, if a reset is pending there's no need to
restart any I/O until the reset is finished.
After a resume, if the interrupt-IN endpoint is halted there's
no need to submit the input URB until the halt has been
cleared.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Daniel Fraga <fragabr@gmail.com>
Tested-by: Daniel Fraga <fragabr@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of open-coding memory allocation and copying form user memory
sequence let's use memdup_user().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
uhid changes the format expected in write() depending on bitness. It
should check the syscall bitness directly.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The wiimote motion plus gyros use two scales to report fast and slow
rotation - below 440 deg/s uses 8192/440 units / deg/s, and above uses
8192/2000 units / deg/s.
Previously this driver attempted to linearize the two by scaling the fast
rate by 18 and the slow by 9, but this results in a scale of
8192*9/440 = ~167.564 for slow and 8192*18/2000 = 73.728 for fast.
Correct the fast motion scale factor so that both report ~167.564
units / deg/s
Signed-off-by: Cyan Ogilvie <cyan.ogilvie@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- functionally equivalent cleanups for wacom driver, making the code
more readable, from Benjamin Tissoires
- a bunch of improvements and fixes for thingm driver from Heiner
Kallweit
- bugfixes to out-of-bound access for generic parsing functions (which
have been there since ever) extract() and implement(), from Dmitry
Torokhov
- a lot of added / improved device support in sony, wacom, microsoft,
multitouch and logitech driver, from various people
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (44 commits)
HID: microsoft: Add ID for MS Wireless Comfort Keyboard
hid: thingm: reorder calls in thingm_probe
HID: i2c-hid: fix OOB write in i2c_hid_set_or_send_report()
HID: multitouch: Release all touch slots on reset_resume
HID: usbhid: enable NO_INIT_REPORTS quirk for Semico USB Keykoard2
HID: penmount: report only one button for PenMount 6000 USB touchscreen controller
HID: i2c-hid: Fix suspend/resume when already runtime suspended
HID: i2c-hid: Add hid-over-i2c name to i2c id table
HID: multitouch: force retrieving of Win8 signature blob
HID: Support for CMedia CM6533 HID audio jack controls
HID: thingm: improve locking
HID: thingm: switch to managed version of led_classdev_register
HID: thingm: remove workqueue
HID: corsair: fix mapping of non-keyboard usages
HID: wacom: close the wireless receiver on remove()
HID: wacom: cleanup input devices
HID: wacom: reuse wacom_parse_and_register() in wireless_work
HID: wacom: move down wireless_work()
HID: wacom: break out parsing of device and registering of input
HID: wacom: break out wacom_intuos_get_tool_type
...
Microsoft Wireless Comfort Keyboard has vendor specific My Favorites
1-5 keys. Linux already supports this buttons on other MS keyboards by
MS_ERGONOMY quirk. So apply MS_ERGONOMY quirk to USB PID 0x00e3
(Microsoft Wireless Optical Desktop Receiver 3.0A). After this
My Favorites 1..5 keys will be reported as KEY_F14..KEY_F15 events.
Signed-off-by: Slava Bacherikov <slava@bacher09.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When reviewing another thingm patch Benjamin Tissoires pointed out
the following: "The problem here is that hid_hw_start() is called
before thingm_version() which allows user space to briefly introduce
races between thingm_version() and any hidraw requests.
The mutex will not help here as it is initialized after hid_hw_start()
and only used for protecting the concurrent access of the rgb."
Avoid this possible issue by calling hid_hw_start() later in the
probe function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Even though hid_hw_* checks that passed in data_len is less than
HID_MAX_BUFFER_SIZE it is not enough, as i2c-hid does not necessarily
allocate buffers of HID_MAX_BUFFER_SIZE but rather checks all device
reports and select largest size. In-kernel users normally just send as much
data as report needs, so there is no problem, but hidraw users can do
whatever they please:
BUG: KASAN: slab-out-of-bounds in memcpy+0x34/0x54 at addr ffffffc07135ea80
Write of size 4101 by task syz-executor/8747
CPU: 2 PID: 8747 Comm: syz-executor Tainted: G BU 3.18.0 #37
Hardware name: Google Tegra210 Smaug Rev 1,3+ (DT)
Call trace:
[<ffffffc00020ebcc>] dump_backtrace+0x0/0x258 arch/arm64/kernel/traps.c:83
[<ffffffc00020ee40>] show_stack+0x1c/0x2c arch/arm64/kernel/traps.c:172
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffc001958114>] dump_stack+0x90/0x140 lib/dump_stack.c:50
[< inline >] print_error_description mm/kasan/report.c:97
[< inline >] kasan_report_error mm/kasan/report.c:278
[<ffffffc0004597dc>] kasan_report+0x268/0x530 mm/kasan/report.c:305
[<ffffffc0004592e8>] __asan_storeN+0x20/0x150 mm/kasan/kasan.c:718
[<ffffffc0004594e0>] memcpy+0x30/0x54 mm/kasan/kasan.c:299
[<ffffffc001306354>] __i2c_hid_command+0x2b0/0x7b4 drivers/hid/i2c-hid/i2c-hid.c:178
[< inline >] i2c_hid_set_or_send_report drivers/hid/i2c-hid/i2c-hid.c:321
[<ffffffc0013079a0>] i2c_hid_output_raw_report.isra.2+0x3d4/0x4b8 drivers/hid/i2c-hid/i2c-hid.c:589
[<ffffffc001307ad8>] i2c_hid_output_report+0x54/0x68 drivers/hid/i2c-hid/i2c-hid.c:602
[< inline >] hid_hw_output_report include/linux/hid.h:1039
[<ffffffc0012cc7a0>] hidraw_send_report+0x400/0x414 drivers/hid/hidraw.c:154
[<ffffffc0012cc7f4>] hidraw_write+0x40/0x64 drivers/hid/hidraw.c:177
[<ffffffc0004681dc>] vfs_write+0x1d4/0x3cc fs/read_write.c:534
[< inline >] SYSC_pwrite64 fs/read_write.c:627
[<ffffffc000468984>] SyS_pwrite64+0xec/0x144 fs/read_write.c:614
Object at ffffffc07135ea80, in cache kmalloc-512
Object allocated with size 268 bytes.
Let's check data length against the buffer size before attempting to copy
data over.
Cc: stable@vger.kernel.org
Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When resetting a device (especially after power loss) it is unlikely
that the firmware will keep the contact tracking data for the previous
touches and will be able to reconcile it with the new contacts, so
let's release all slots on reset resume as start anew.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The device which identifies itself as a "USB Keykoard" (no typo)
with VID:PID 1a2c:0027 does not seem to be handling the reports
initialization very well.
This results in a "usb_submit_urb(ctrl) failed: -1" message from the
kernel when connected, and a delay before its initialization. It can
also cause the hang the system.
This patch adds the quirk for this device, which causes the delay
to disappear. It is named as "USB Keykoard2" because the "USB Keykoard"
already exists.
Signed-off-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
PenMount 6000 USB resistive touchscreen controller reports it has three
buttons, while in reality it doesn't have any and doesn't support active
styli, and only generates touch events.
In penmount_input_mapping(), map only the first button (with code 0),
ignore the rest.
Signed-off-by: Andrew Shadura <andrew.shadura@collabora.co.uk>
Tested-by: Christian Gmeiner <c.gmeiner@bachmann.info
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On ACPI-based systems ACPI power domain code runtime resumes device before
calling suspend method, which ensures that i2c-hid suspend code starts with
device not in low-power state and with interrupts enabled.
On other systems, especially if device is not a part of any power domain,
we may end up calling driver's system-level suspend routine while the
device is runtime-suspended (with controller in presumably low power state
and interrupts disabled). This will result in interrupts being essentially
disabled twice, and we will only re-enable them after both system resume
and runtime resume methods complete. Unfortunately i2c_hid_resume() calls
i2c_hid_hwreset() and that only works properly if interrupts are enabled.
Also if device is runtime-suspended driver's suspend code may fail if it
tries to issue I/O requests.
Let's fix it by runtime-resuming the device if we need to run HID driver's
suspend code and also disabling interrupts only if device is not already
runtime-suspended. Also on resume we mark the device as running at full
power (since that is what resetting will do to it).
Reviewed-by: Benson Leung <bleung@chromium.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When using the device tree binding OF compatible = "hid-over-i2c" the
i2c id table also needs to have that name in order to auto load this
driver, since i2c core reports module alias as i2c:<string> where
<string> is compatible string of OF binding stripped of manufacturer's
prefix.
Tested-by: Andrew Duggan <aduggan@synaptics.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Synaptics 0x11e5 over I2C found in the Asus T100-CHI requires to
fetch the signature blob to actually start sending events.
With this patch, we should be close enough to the Windows driver which
checks the content of the blob at plugin to validate or not the
touchscreen.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=113481
Fixes: 6d4f5440 ("HID: multitouch: Fetch feature reports on demand for Win8 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The C-Media CM6533 is a USB audio chip featuring it's jack detection
capability.The device originates an interrupt transfer via HID interface each
time when a jack event occurs. The purpose of this patch is to handle hid raw
events to keep the operating system informed of user interactions.
Signed-off-by: Ben Chen <ben_chen@bizlinktech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reading from the device consists of two operations: sending the read
command and the actual read from the device. If the device is accessed
in between we might read wrong data. Therefore protect the full sequence
of both operations with a mutex.
Also change the semantics of thingm_recv to include both operations.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplify the code by switching to the managed version of
led_classdev_register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Defining workqueues in LED drivers isn't needed any longer as the LED core
was extended with a generic workqueue recently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This fixes a bug where the Volume Up key was ignored because it uses the same usage code as G18. Special Corsair usage codes are in the keyboard page, other pages should be left to the generic driver.
Signed-off-by: Clément Vuchener <clement.vuchener@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
rmmod/insmod the wacom.ko module does not work for the receiver because
it was not previously closed. Now, we can hack with the wireless receiver
without having to unplug/replug it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Just some cleaning up when the input devices are unregistered.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Removes duplicated code.
The only difference is that we now need to stop and start the attached hid
device, but this is a small cost.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If wireless_work() wants to reuse parse_and_register(), we need to have
it declared after this function.
No functional changes.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplifies the .probe() and will allow to reuse this path in the future.
Few things are reshuffled in .probe():
- init wacom struct earlier
- then retrieve the report descriptor
- then parse it and allocate/register inputs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allow to reuse the code in a later series and simplifies
the reading of wacom_intuos_inout().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_ignore_special_drivers works fine until hid_scan_report autodetects and
reassign devices (for hid-multitouch, hid-microsoft and hid-rmi).
Simplify the handling of the parameter: if it is there, use hid-generic, no
matter what, and if not, scan the device or rely on the hid_have_special_driver
table.
This was detected while trying to disable hid-multitouch on a Surface Pro cover
which prevented to use the keyboard.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The patch that added Logitech Dual Action gamepad support forgot to
update the special driver list for the device. This caused the logitech
driver not to probe unless kernel module load order was favorable.
Update the special driver list to fix it. Thanks to Simon Wood for the
idea.
Cc: Vitaly Katraew <zawullon@gmail.com>
Fixes: 56d0c8b7c8 ("HID: add support for Logitech Dual Action gamepads")
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Double-underscore prefixed types are unnecessary in pure kernel code,
replace them with the non prefixed equivalents.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
WARNING: Block comments use a trailing */ on a separate line
#822: FILE: drivers/hid/hid-sony.c:822:
+ * number but it's not needed for correct operation */
WARNING: Block comments use a trailing */ on a separate line
#828: FILE: drivers/hid/hid-sony.c:828:
+ * buttons multiple keypresses are allowed */
WARNING: Block comments use a trailing */ on a separate line
#854: FILE: drivers/hid/hid-sony.c:854:
+ * 0xff and 11th is for press indication */
WARNING: Missing a blank line after declarations
#1930: FILE: drivers/hid/hid-sony.c:1930:
+ struct sony_sc *sc = container_of(work, struct sony_sc, state_worker);
+ sc->send_output_report(sc);
WARNING: Block comments use a trailing */ on a separate line
#2510: FILE: drivers/hid/hid-sony.c:2510:
+ * Logitech joystick from the device descriptor. */
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
./scripts/checkpatch.pl \
--types "SPACING,TRAILING_WHITESPACE,POINTER_LOCATION,CODE_INDENT" \
-f drivers/hid/hid-sony.c
ERROR: trailing whitespace
#933: FILE: drivers/hid/hid-sony.c:933:
+^I * $
ERROR: space prohibited after that open square bracket '['
#947: FILE: drivers/hid/hid-sony.c:947:
+ [ 1] = BTN_TRIGGER_HAPPY1,
ERROR: space prohibited after that open square bracket '['
#948: FILE: drivers/hid/hid-sony.c:948:
+ [ 2] = BTN_TRIGGER_HAPPY2,
ERROR: space prohibited after that open square bracket '['
#949: FILE: drivers/hid/hid-sony.c:949:
+ [ 3] = BTN_TRIGGER_HAPPY3,
ERROR: space prohibited after that open square bracket '['
#950: FILE: drivers/hid/hid-sony.c:950:
+ [ 4] = BTN_TRIGGER_HAPPY4,
ERROR: space prohibited after that open square bracket '['
#951: FILE: drivers/hid/hid-sony.c:951:
+ [ 5] = BTN_TRIGGER_HAPPY5,
ERROR: space prohibited after that open square bracket '['
#952: FILE: drivers/hid/hid-sony.c:952:
+ [ 6] = BTN_TRIGGER_HAPPY6,
ERROR: space prohibited after that open square bracket '['
#953: FILE: drivers/hid/hid-sony.c:953:
+ [ 7] = BTN_TRIGGER_HAPPY7,
ERROR: space prohibited after that open square bracket '['
#954: FILE: drivers/hid/hid-sony.c:954:
+ [ 8] = BTN_TRIGGER_HAPPY8,
ERROR: space prohibited after that open square bracket '['
#955: FILE: drivers/hid/hid-sony.c:955:
+ [ 9] = BTN_TRIGGER_HAPPY9,
ERROR: "(foo*)" should be "(foo *)"
#1032: FILE: drivers/hid/hid-sony.c:1032:
+ void(*send_output_report)(struct sony_sc*);
WARNING: missing space after return type
#1032: FILE: drivers/hid/hid-sony.c:1032:
+ void(*send_output_report)(struct sony_sc*);
ERROR: "(foo*)" should be "(foo *)"
#2261: FILE: drivers/hid/hid-sony.c:2261:
+ void(*send_output_report)(struct sony_sc*))
WARNING: missing space after return type
#2261: FILE: drivers/hid/hid-sony.c:2261:
+ void(*send_output_report)(struct sony_sc*))
ERROR: code indent should use tabs where possible
#2449: FILE: drivers/hid/hid-sony.c:2449:
+ */$
total: 13 errors, 2 warnings, 2570 lines checked
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds a warning message stating that the sysfs group was not able to be
created for the passed hid_device structure pointer with dev_warn.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Reviewed-by: Benjamin Tissoires <benajmin.tissoires@redhat.com>
[jkosina@suse.cz: massaged changelog a bit]
[jkosina@suse.cz: reformatted source]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The midi controller times-out while initializing reports, this
causes boot to take an extra 10 seconds. The device descriptor
advertises that it has an internal HID device but seems to not
actually do anything useful.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hidpp_ff_init() and hidpp_ff_deinit() are not used outside of
hid-logitech-hidpp.c, so let's make them static.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch implements force feedback support for the Logitech
G920 Driving Force Racing Wheel. It is a generic implementation
of feature 0x8123 of the Logitech HID++ protocol and should be
usable for any future devices that implement this feature.
This patch should be applied after the basic G920 support patch
by Simon Wood:
http://www.spinics.net/lists/linux-input/msg42174.html
The driving supports everything that is supported by the G920
firmware:
FF_CONSTANT
FF_PERIODIC
FF_SINE
FF_SQUARE
FF_SAW_UP
FF_SAW_DOWN
FF_TRIANGLE
FF_SPRING
FF_DAMPER
FF_AUTOCENTER
FF_GAIN
and for version 2 firmware also:
FF_FRICTION
FF_INERTIA
FF_RAMP
Both envelopes and replay values are supported as well, but some
problems may occur when using firmware release 1. There is also a
small residual clockwise damper in the wheel when using the first
firmware release. All problems are fixed in the soon te be released
firmware version 2.
The default spring is disabled by permanently placing a spring
force in the wheel. This spring is also used as the autocenter
spring.
Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck
in XBox since the xpad changes where not included). Michal has an
alternative approach documented here (and the changes should be submitted
upstream to usb_modeswitch project):
===
Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the
following content:
DefaultVendor=046d
DefaultProduct=c261
MessageEndpoint=01
ResponseEndpoint=01
TargetClass=0x03
MessageContent="0f00010142"
Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and
watch the magic happen:)
===
[jkosina@suse.cz: added information about mode switching from Simon]
[jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon]
[jkosina@suse.cz: fix merge conflict due to to_hid_device() changes]
Signed-off-by: Edwin Velds <e.velds@gmail.com>
Tested-by: Elias Vanderstuyft <elias.vds@gmail.com>
Tested-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 0925636042 ("HID: rmi: Disable scanning if the device is not a wake
source") introduced a regression for devices which use hid-rmi to handle
composite USB devices. The suspend or resume callbacks are not checking
that the device is a RMI device before calling rmi_read or rmi_write.
This results in dereferencing uninitialized variables on non RMI devices. This
patch checks that the RMI_DEVICE flag is set before sending RMI commands to the
device.
Reported-by: Rodrigo Gomes <rodrigo.toste.gomes@gmail.com>
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The correct product ID for the old version of the raphnet 4nes4snes
device was 0x0a9d, not 0x0a8d.
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The asm-generic tree this time contains one series from Nicolas Pitre
that makes the optimized do_div() implementation from the ARM
architecture available to all architectures. This also adds stricter
type checking for callers of do_div, which has uncovered a number
of bugs in existing code, and fixes up the ones we have found.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4psa
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"The asm-generic tree this time contains one series from Nicolas Pitre
that makes the optimized do_div() implementation from the ARM
architecture available to all architectures.
This also adds stricter type checking for callers of do_div, which has
uncovered a number of bugs in existing code, and fixes up the ones we
have found"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
ARM: asm/div64.h: adjust to generic codde
__div64_32(): make it overridable at compile time
__div64_const32(): abstract out the actual 128-bit cross product code
do_div(): generic optimization for constant divisor on 32-bit machines
div64.h: optimize do_div() for power-of-two constant divisors
mtd/sm_ftl.c: fix wrong do_div() usage
drm/mgag200/mgag200_mode.c: fix wrong do_div() usage
hid-sensor-hub.c: fix wrong do_div() usage
ti/fapll: fix wrong do_div() usage
ti/clkt_dpll: fix wrong do_div() usage
tegra/clk-divider: fix wrong do_div() usage
imx/clk-pllv2: fix wrong do_div() usage
imx/clk-pllv1: fix wrong do_div() usage
nouveau/nvkm/subdev/clk/gk20a.c: fix wrong do_div() usage
Plugging a Logitech DJ receiver with KASAN activated raises a bunch of
out-of-bound readings.
The fields are allocated up to MAX_USAGE, meaning that potentially, we do
not have enough fields to fit the incoming values.
Add checks and silence KASAN.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
extract() and implement() access buffer containing reports in 64-bit
chunks, but there is no guarantee that buffers are padded to 64 bit
boundary. In fact, KASAN has caught such OOB access with i2c-hid and
Synaptics touch controller.
Instead of trying to hunt all parties that allocate buffers and make
sure they are padded, let's switch extract() and implement() to byte
access. It is a bit slower, bit we are not dealing with super fast
devices here.
Also let's fix link to the HID spec while we are at it.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The nyko core controller uses the same output report format as the
sixaxis controllers, but it expects the report id at offset 1.
This does not interfere with the official controllers as this byte
is considered a padding byte by the current code.
Signed-off-by: Scott Moreau <oreaus@gmail.com>
Acked-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds rumble and LED support for nyko core controllers
using the sino lite chip vendor:1345 product:3008, for PS3.
Setting operational mode and output reports are the same as
sixaxis but the input report has a different format since the
PS3 accepts HID usb devices. For it to work, an exception is
needed to skip overriding the report descriptor and use the
original one.
Signed-off-by: Scott Moreau <oreaus@gmail.com>
Acked-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When setting the operational mode, some third party (Speedlink Strike-FX)
gamepads refuse the output report. Failing here means we refuse to
initialize the gamepad while this should be harmless.
The weird part is that the initial commit that added this: a7de9b8
("HID: sony: Enable Gasia third-party PS3 controllers") mentions this
very same controller as one requiring this output report.
Anyway, it's broken for one user at least, so let's change it.
We will report an error, but at least the controller should work.
And no, these devices present themselves as legacy Sony controllers
(VID:PID of 054C:0268, as in the official ones) so there are no ways
of discriminating them from the official ones.
https://bugzilla.redhat.com/show_bug.cgi?id=1255325
Reported-and-tested-by: Max Fedotov <thesourcehim@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
INTUOSHT2 in range event is not used to indicate in proximity state.
INTUOSHT2 only has one stylus.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
stylus_in_proximity was introduced to support touch arbitration
before in range was supported. With in range event, the logic
changed. stylus_in_proximity should be set for both in prox and
in range events.
To finish a clean touch arbitration logic, we should send touch
up (if it was down) before posting any general pen events.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move general events related data validation to wacom_intuos_general.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move wacom_intuos_schedule_prox_event inside wacom_intuos_general
so we don't call it when general event data isn't ready.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
Pull HID updates from Jiri Kosina:
- appoint Benjamin Tissoires as co-maintainer / designated reviewer
- sysfs report_descriptor visibility fix for unclaimed devices, from
Andy Lutomirski
- suspend/resume fixes for Sony driver from Frank Praznik
- IRQ deadlock fix from Ioan-Adrian Ratiu
- hid-i2c fixes affecting (at least) Yoga 900 from Mika Westerberg and
Srinivas Pandruvada
- a lot of new device support (especially, but not limited to, Wacom)
and assorted small misc fixes
- almost complete G920 support; the only bit that is missing is
switching the device to HID mode automatically; Simon Wood and Michal
Maly are working on it.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (46 commits)
Revert "INPUT: xpad: switch Logitech G920 Wheel into HID mode"
HID: sensor-hub: Add quirk for Lenovo Yoga 900 with ITE Chips
HID: Add new PID for Microchip Pick16F1454
HID: wacom: Use correct report to query pen ID from INTUOSHT2 devices
HID: i2c-hid: Prevent sending reports from racing with device reset
HID: use kobj_to_dev()
HID: wiimote: use dev_to_wii()
HID: add a new helper to_hid_driver()
HID: use to_hid_device()
HID: move to_hid_device() to hid.h
HID: usbhid: use to_usb_device
HID: corsair: Convert to use module_hid_driver
HID: input: ignore the battery in OKLICK Laser BTmouse
HID: wacom: Fix pad button range for CINTIQ_COMPANION_2
HID: wacom: Fix touchring value reporting
HID: wacom: Report 'strip2' values in ABS_RY
HID: wacom: Limit touchstrip data to 13 bits
HID: wacom: bitwise vs logical ORs
HID: wacom: Apply lowres quirk to BAMBOO_TOUCH devices
HID: enable hid device to suspend/resume asynchronously
...
This needs same quirk as applied to other YOGA sensor hubs. Refer to commit
21589ebda6 ("HID: sensor-hub: Add in quirk for Lenovo Yogas with ITE")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There seems to be a new version of the Microchip Pick16F1454 with a
different PID (0xf2f7). This device should also be ignored by the HID
driver. The PID was observed with the second version of the Yepkit Ykush
USB hub.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Unlike other tablets which are compatible with the wacom_intuos_irq handler,
INTUOSHT2 devices provide pen ID with report ID 8 instead of 5. To ensure
wacom_intuos_schedule_prox_event works as intended for these tablets, we
must be sure it uses the correct report ID in this case.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: linux-input@vger.kernel.org
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an i2c-hid device is resumed from system sleep the driver resets
the device to be sure it is in known state. The device is expected to
issue an interrupt when reset is complete.
This reset might take few milliseconds to complete so if the HID driver
on top (hid-rmi) starts to set up the device by sending feature reports
etc. the device might not issue the reset complete interrupt anymore.
Below is what happens to touchpad on Lenovo Yoga 900 during resume from
system sleep:
[ 24.790951] i2c_hid i2c-SYNA2B29:00: i2c_hid_hwreset
[ 24.790973] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_power
[ 24.790982] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 00 08
[ 24.793011] i2c_hid i2c-SYNA2B29:00: resetting...
[ 24.793016] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 00 01
Here i2c-hid sends reset command to the touchpad.
[ 24.794012] i2c_hid i2c-SYNA2B29:00: input: 06 00 01 00 00 00
[ 24.794051] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_or_send_report
[ 24.794059] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command:
cmd=22 00 3f 03 0f 23 00 04 00 0f 01
Now hid-rmi puts the touchpad to correct mode by sending it a feature
report. This makes the touchpad not to issue reset complete interrupt.
[ 24.796092] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: waiting...
i2c-hid starts to wait for the reset interrupt to trigger which never
happens.
[ 24.798304] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_or_send_report
[ 24.798313] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command:
cmd=25 00 17 00 09 01 42 00 2e 00 19 19 00 10 cc 06 74 04 0f
19 00 00 00 00 00
Yet another output report from hid-rmi driver.
[ 29.795630] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: finished.
[ 29.795637] i2c_hid i2c-SYNA2B29:00: failed to reset device.
After 5 seconds i2c-hid driver times out.
[ 29.795642] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_power
[ 29.795649] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 01 08
[ 29.797576] dpm_run_callback(): i2c_hid_resume+0x0/0xb0 returns -61
[ 29.797584] PM: Device i2c-SYNA2B29:00 failed to resume: error -61
After this the touchpad does not work anymore (and also resume itself
gets slowed down because of the timeout).
Prevent sending of feature/output reports while the device is being
reset by adding a mutex which is held during that time.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Nish Aravamudan <nish.aravamudan@gmail.com>
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a new helper to_hid_driver() and use it in hid-core.c.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
to_hid_device() macro is defined in both hid-lg4ff.c and
hid-logitech-hidpp.c. So I move it to include/linux/hid.h.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse, when asked about the battery, ceases to report movements and
clicks. So just don't ask.
Signed-off-by: Alexander E. Patrakov <patrakov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit c7f0522 incorrectly constructs the 'buttons' variable for the
CINTIQ_COMPANION_2 case. The high nybble of data[2] is shifted four
bits too far, leaving the bits associated with BTN_7 through BTN_A
unset.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit c7f0522 reports incorrect touchring values to userspace. This is
due to its incorrect handling of the 'touched' bit present in the 'ring1'
and 'ring2' variables. Instead of using this bit when determining if a
value should be sent, the ABS_WHEEL and ABS_INPUT check (different?!)
portions of the position bits. Furthermore, the full values of 'ring1'
and 'ring2' are reported to userspace, despite the 'touched' flag
needing to be trimmed beforehand. This commit addresses both issues.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit c7f0522 accidentally used ABS_RX for reporting both 'strip1' and
'strip2', when the latter should actually be reported through ABS_RY.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit c7f0522 uses sixteen bits of data in the construction of 'strip1'
and 'strip2'. This can cause problems in some cases, however, since some
tablets store flags in the MSB of data[2] and data[4] that should not be
included in these values. This restores the 0x1f mask that used prior
to c7f0522.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Smatch complains that these should probably be bitwise ORs instead of
logical. It doesn't matter for "prox" but it makes a difference for
"strip1" and "strip2".
Fixes: c7f0522a1a ('HID: wacom: Slim down wacom_intuos_pad processing')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Here are a number of small USB fixes for 4.4-rc5. All of them have been
in linux-next. The majority are gadget and phy issues, with a few new
quirks and device ids added as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZs8fkACgkQMUfUDdst+ym/HwCgxdhop3PMk9QxCVaEdxcqv10p
PDkAn0uOW1sdRsHVRhutjcc29+AUJggk
=ybrB
-----END PGP SIGNATURE-----
Merge tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are a number of small USB fixes for 4.4-rc5. All of them have
been in linux-next. The majority are gadget and phy issues, with a
few new quirks and device ids added as well"
* tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (32 commits)
USB: add quirk for devices with broken LPM
xhci: fix usb2 resume timing and races.
usb: musb: fail with error when no DMA controller set
usb: gadget: uvc: fix permissions of configfs attributes
usb: musb: core: Fix pm runtime for deferred probe
usb: phy: msm: fix a possible NULL dereference
USB: host: ohci-at91: fix a crash in ohci_hcd_at91_overcurrent_irq
usb: Quiet down false peer failure messages
usb: xhci: fix config fail of FS hub behind a HS hub with MTT
xhci: Fix memory leak in xhci_pme_acpi_rtd3_enable()
usb: Use the USB_SS_MULT() macro to decode burst multiplier for log message
USB: whci-hcd: add check for dma mapping error
usb: core : hub: Fix BOS 'NULL pointer' kernel panic
USB: quirks: Apply ALWAYS_POLL to all ELAN devices
usb-storage: Fix scsi-sd failure "Invalid field in cdb" for USB adapter JMicron
USB: quirks: Fix another ELAN touchscreen
usb: dwc3: gadget: don't prestart interrupt endpoints
USB: serial: Another Infineon flash loader USB ID
USB: cdc_acm: Ignore Infineon Flash Loader utility
USB: cp210x: Remove CP2110 ID from compatibility list
...
When splitting the touch-only "BAMBOO_TOUCH" type out of the existing
"BAMBOO_PT" type in 3b164a00, the lowres quirk was not updated so that
it would continue to apply to these devices (effectively only the 0xD0).
The absence of this quirk does not significantly impact usability, but
is a correctness issue nonetheless.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now, PM core supports asynchronous suspend/resume mode for devices
during system suspend/resume, and the power state transition of one
device may be completed in separate kernel thread. PM core ensures
all power state transition timing dependency between devices. This
patch enables hid devices to suspend/resume asynchronously. This
will take advantage of multicore and improve system suspend/resume
speed.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
"INTUOSREAD" and "INTUOSWRITE" are poorly named. These are report IDs
for pen ID (proximity) packets. It should be noted that the latter is
only used on Intuos/Intuos2 for a second stylus when DualTrack is in use.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make the logic for reading X, Y, distance, and pressure a bit more
clear. An additional bit was stuffed into the packet format many
models back, and /most/ devices in use will use it. If we happen
to be dealing with a particularly old tablet, just shift it off
the end to pretend we never read it.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Continue re-organizing and trimming cases to make it easier to wrap
the brain around. A number of changes were made after consulting the
protocol spec and so don't necessarily follow from the code itself.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reasoning through the conditions under which a particular block of code
in 'wacom_intuos_general' will be reached is not at all easy due to the
sheer number of magic masks and comparisons. Remove these and replace
them with a switch statement over the various 'types' of packets that
will be encountered.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>