Граф коммитов

31 Коммитов

Автор SHA1 Сообщение Дата
Finn Thain f74faec6b3 m68k/mac: Replace via-maciisi driver with via-cuda driver
Change the device probe test in the via-cuda.c driver so it will load on
Egret-based machines too. Remove the now redundant via-maciisi.c driver.

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-02-07 16:56:25 +11:00
Finn Thain d23eee88b5 via-cuda: Add support for Egret system controller
The Egret system controller was the predecessor to the Cuda and the
differences are minor.

On Cuda, byte acknowledgement requires one transition of the TACK
signal; on Egret two are needed. On Cuda, TIP is active low; on Egret
it is active high. And Cuda raises certain interrupts that Egret omits.

Accomodating these differences complicates the Cuda driver slightly
but avoids a lot of duplication (see next patch).

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-02-07 16:56:24 +11:00
Finn Thain 97ced1aac0 via-cuda: Initialize data_index early and increment consistently
Initialize data_index where appropriate to improve readability and
assist debugging. This change doesn't affect driver behaviour.

I prefer to see
	current_req->data[data_index++]
in place of
	current_req->data[0]
or
	current_req->data[1]
inasmuchas it becomes obvious what the data_index variable does.

Moreover, the actual value of data_index when examined at any given moment
tells me something about prior events, which did prove helpful.

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-02-07 16:56:23 +11:00
Finn Thain ac39452e94 via-cuda: Use spinlock_irq_save/restore instead of enable/disable_irq
The cuda_start() function uses spinlock_irq_save/restore for mutual
exclusion. Let's have cuda_poll() do the same when polling the VIA
interrupt.

The benefit to disabling local irqs when the interrupt is being polled
is that the interrupt handler now has the same timing properties
regardless of whether it is invoked normally or from cuda_poll().

This driver was written back when local irqs remained enabled during
execution of interrupt handlers and cuda_poll() was probably trying
to achieve the same effect by use of enable/disable_irq.

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-02-07 16:56:22 +11:00
Finn Thain a646624322 via-cuda: Avoid TREQ race condition
When a read transaction completes, one of several things will happen:
a new transfer is started by the driver, a new transfer request
is raised by the Cuda (i.e. TREQ asserted), or both happen at once.

When both happen at once, there is a race condition between the TREQ test
in the read_done state and the same test in cuda_start(). Moreover, the
former test uses a stale TREQ value.

Theoretically, this can result in the undesirable outcome that the
interrupt handler completes with the state machine 'idle' when it should
instead start the next transaction.

Avoid this race by calling cuda_start() first and then confirming that it
succeeded. If not, test the current TREQ value before entering the
'reading' state.

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-02-07 16:56:21 +11:00
Finn Thain cfbf99801b via-cuda: Fix re-initialization of reply_ptr and reading_reply
When reading_reply is set, reply_ptr points into an adb_request struct.
Conversely, when reply_ptr instead points into the global cuda_rbuf,
reading_reply must be false.

Unfortunately, this rule can be violated because re-initialization
of reply_ptr and reading_reply presently depends on the TREQ input.

Fix this by re-initializing reply_ptr and reading_reply as soon as they
are known to be invalid.

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-02-07 16:56:20 +11:00
Finn Thain fe73b582f1 via-cuda: Prevent read buffer overflow
If the Cuda driver does not enter the 'read_done' state for some
reason, it may continue in the 'reading' state until the buffer
overflows. Add a bounds check to prevent this.

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-02-07 16:56:19 +11:00
Finn Thain fd7a65a27c via-cuda: Add TREQ, TIP and TACK signal helpers
Introduce some helpers for handling the signalling between VIA and
Cuda. This abstraction will be used to add support for Egret devices,
which utilize slightly different signalling.

Don't invert the sense of the Cuda's active-low signals when storing
them in the 'status' variable. Just assert, negate and test those
signals using the helpers.

The state machine does not need to test its own output signals to
figure out what to do next: the next state depends on the Cuda's TREQ
output. Just call the TREQ_asserted() helper function to test for that.

Similarly, there is no need to store pin directions in the 'status'
variable. That was only useful for debugging messages.

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-02-07 16:56:18 +11:00
Finn Thain 06d7e99408 via-cuda: Remove redundant temporary variable
There is no possibility that current_req can change during execution of
cuda_start(). This can be confirmed by inspection: cuda_lock is always
held whenever cuda_start() is called or current_req is modified.

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-02-07 16:56:17 +11:00
Finn Thain 523717d149 via-cuda: Cleanup printk calls
Add missing log message severity, remove old debug messages and
replace printk() loop with print_hex_dump() call.

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-02-07 16:56:16 +11:00
Michael Ellerman ef24ba7091 powerpc: Remove all usages of NO_IRQ
NO_IRQ has been == 0 on powerpc for just over ten years (since commit
0ebfff1491 ("[POWERPC] Add new interrupt mapping core and change
platforms to use it")). It's also 0 on most other arches.

Although it's fairly harmless, every now and then it causes confusion
when a driver is built on powerpc and another arch which doesn't define
NO_IRQ. There's at least 6 definitions of NO_IRQ in drivers/, at least
some of which are to work around that problem.

So we'd like to remove it. This is fairly trivial in the arch code, we
just convert:

    if (irq == NO_IRQ)	to	if (!irq)
    if (irq != NO_IRQ)	to	if (irq)
    irq = NO_IRQ;	to	irq = 0;
    return NO_IRQ;	to	return 0;

And a few other odd cases as well.

At least for now we keep the #define NO_IRQ, because there is driver
code that uses NO_IRQ and the fixes to remove those will go via other
trees.

Note we also change some occurrences in PPC sound drivers, drivers/ps3,
and drivers/macintosh.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-09-20 20:57:12 +10:00
Anton Blanchard 4a1b08e844 powerpc: Move via-cuda symbol exports next to function definitions
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2014-09-25 23:14:37 +10:00
Geert Uytterhoeven 330dae1999 mac: Make cuda_init_via() __init
cuda_init_via() is called from find_via_cuda() only, which is __init.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2013-07-01 11:10:36 +10:00
David Howells 9ffc93f203 Remove all #inclusions of asm/system.h
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it.  Performed with the following command:

perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`

Signed-off-by: David Howells <dhowells@redhat.com>
2012-03-28 18:30:03 +01:00
Finn Thain 18814ee846 mac68k: start CUDA early
The valkyriefb driver needs the CUDA to work in order to set the video
mode at boot. So initialise the device earlier, and bring the m68k code
closer to the powermac code.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2010-02-27 18:31:13 +01:00
Finn Thain 429dbf53bc m68k: machw.h cleanup
Remove some more cruft from machw.h and drop the #include where it isn't
needed.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2008-12-28 20:00:03 +01:00
Finn Thain 0251c38ce5 CUDA ADB fixes
Fix the flakiness in the CUDA ADB driver on m68k macs (keypresses getting
wedged down or ADB just going AWOL altogether).

The only IRQ used by this driver is the VIA shift register IRQ. The PowerMac
conditional code disables the other VIA IRQ sources, so don't mess with the
other IRQ flags in the common code -- m68k macs need them.

When polling, don't disable local interrupts when we only need to disable the
CUDA interrupt.

Unless polling, don't clear the shift register IRQ flag. On m68k macs this
creates a race that often breaks CUDA ADB.

Tested on Quadra 840av and LC630 (both m68k); also Beige G3 (powerpc).

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-04 17:59:07 -07:00
Stephen Rothwell 01b2726dd1 [POWERPC] Rename get_property to of_get_property: partial drivers
This does drivers/machintosh and the hvc code.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-04-27 15:51:56 +10:00
Paul Mackerras a48141db68 Revert "[POWERPC] Rename get_property to of_get_property: drivers"
This reverts commit d05c7a80cf,
which included changes which should go via other subsystem
maintainers.
2007-04-26 22:24:31 +10:00
Stephen Rothwell d05c7a80cf [POWERPC] Rename get_property to of_get_property: drivers
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-04-13 03:55:19 +10:00
Tim Schmielau cd354f1ae7 [PATCH] remove many unneeded #includes of sched.h
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there.  Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.

To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.

Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm.  I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).

Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14 08:09:54 -08:00
Olaf Hering 872758563d [POWERPC] move variables in drivers/macintosh to bss
Move all the initialized variables to bss.
Mark a version string as const.

Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-13 15:35:52 +11:00
Olof Johansson 49f19ce401 [PATCH] powerpc: irq change build breaks
Fix up some of the buildbreaks from the irq handler changes.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-05 18:39:04 -07:00
David Howells 7d12e780e0 IRQ: Maintain regs pointer globally rather than passing to IRQ handlers
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.

The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around.  On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).

Where appropriate, an arch may override the generic storage facility and do
something different with the variable.  On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.

Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions.  Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller.  A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.

I've build this code with allyesconfig for x86_64 and i386.  I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.

This will affect all archs.  Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:

	struct pt_regs *old_regs = set_irq_regs(regs);

And put the old one back at the end:

	set_irq_regs(old_regs);

Don't pass regs through to generic_handle_irq() or __do_IRQ().

In timer_interrupt(), this sort of change will be necessary:

	-	update_process_times(user_mode(regs));
	-	profile_tick(CPU_PROFILING, regs);
	+	update_process_times(user_mode(get_irq_regs()));
	+	profile_tick(CPU_PROFILING);

I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().

Some notes on the interrupt handling in the drivers:

 (*) input_dev() is now gone entirely.  The regs pointer is no longer stored in
     the input_dev struct.

 (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking.  It does
     something different depending on whether it's been supplied with a regs
     pointer or not.

 (*) Various IRQ handler function pointers have been moved to type
     irq_handler_t.

Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 15:10:12 +01:00
Jeremy Kerr 018a3d1db7 [POWERPC] powermac: Constify & voidify get_property()
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.

powermac platform & macintosh driver changes.

Built for pmac32_defconfig, g5_defconfig

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-07-31 15:55:05 +10:00
Benjamin Herrenschmidt 0ebfff1491 [POWERPC] Add new interrupt mapping core and change platforms to use it
This adds the new irq remapper core and removes the old one.  Because
there are some fundamental conflicts with the old code, like the value
of NO_IRQ which I'm now setting to 0 (as per discussions with Linus),
etc..., this commit also changes the relevant platform and driver code
over to use the new remapper (so as not to cause difficulties later
in bisecting).

This patch removes the old pre-parsing of the open firmware interrupt
tree along with all the bogus assumptions it made to try to renumber
interrupts according to the platform. This is all to be handled by the
new code now.

For the pSeries XICS interrupt controller, a single remapper host is
created for the whole machine regardless of how many interrupt
presentation and source controllers are found, and it's set to match
any device node that isn't a 8259.  That works fine on pSeries and
avoids having to deal with some of the complexities of split source
controllers vs. presentation controllers in the pSeries device trees.

The powerpc i8259 PIC driver now always requests the legacy interrupt
range. It also has the feature of being able to match any device node
(including NULL) if passed no device node as an input. That will help
porting over platforms with broken device-trees like Pegasos who don't
have a proper interrupt tree.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-07-03 21:36:01 +10:00
Jörn Engel 6ab3d5624e Remove obsolete #include <linux/config.h>
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 19:25:36 +02:00
Benjamin Herrenschmidt cc5d0189b9 [PATCH] powerpc: Remove device_node addrs/n_addr
The pre-parsed addrs/n_addrs fields in struct device_node are finally
gone. Remove the dodgy heuristics that did that parsing at boot and
remove the fields themselves since we now have a good replacement with
the new OF parsing code. This patch also fixes a bunch of drivers to use
the new code instead, so that at least pmac32, pseries, iseries and g5
defconfigs build.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-09 14:53:55 +11:00
Benjamin Herrenschmidt 51d3082fe6 [PATCH] powerpc: Unify udbg (#2)
This patch unifies udbg for both ppc32 and ppc64 when building the
merged achitecture. xmon now has a single "back end". The powermac udbg
stuff gets enriched with some ADB capabilities and btext output. In
addition, the early_init callback is now called on ppc32 as well,
approx. in the same order as ppc64 regarding device-tree manipulations.
The init sequences of ppc32 and ppc64 are getting closer, I'll unify
them in a later patch.

For now, you can force udbg to the scc using "sccdbg" or to btext using
"btextdbg" on powermacs. I'll implement a cleaner way of forcing udbg
output to something else than the autodetected OF output device in a
later patch.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-09 14:49:54 +11:00
Jon Loeliger aacaf9bd96 [PATCH] powerpc: Remove sections use from ppc64 and drivers
Here is a new patch that removes all notion of the pmac, prep,
chrp and openfirmware initialization sections, and then unifies
the sections.h files without those __pmac, etc, sections identifiers
cluttering things up.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-09-19 09:38:49 +10:00
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00