Pull drm updates from Dave Airlie:
"This is the main git pull for the drm,
I pretty much froze major pulls at -rc5/6 time, and haven't had much
fallout, so will probably continue doing that.
Lots of changes all over, big internal header cleanup to make it clear
drm features are legacy things and what are things that modern KMS
drivers should be using. Also big move to use the new generic fences
in all the TTM drivers.
core:
atomic prep work,
vblank rework changes, allows immediate vblank disables
major header reworking and cleanups to better delinate legacy
interfaces from what KMS drivers should be using.
cursor planes locking fixes
ttm:
move to generic fences (affects all TTM drivers)
ppc64 caching fixes
radeon:
userptr support,
uvd for old asics,
reset rework for fence changes
better buffer placement changes,
dpm feature enablement
hdmi audio support fixes
intel:
Cherryview work,
180 degree rotation,
skylake prep work,
execlist command submission
full ppgtt prep work
cursor improvements
edid caching,
vdd handling improvements
nouveau:
fence reworking
kepler memory clock work
gt21x clock work
fan control improvements
hdmi infoframe fixes
DP audio
ast:
ppc64 fixes
caching fix
rcar:
rcar-du DT support
ipuv3:
prep work for capture support
msm:
LVDS support for mdp4, new panel, gpu refactoring
exynos:
exynos3250 SoC support, drop bad mmap interface,
mipi dsi changes, and component match support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (640 commits)
drm/mst: rework payload table allocation to conform better.
drm/ast: Fix HW cursor image
drm/radeon/kv: add uvd/vce info to dpm debugfs output
drm/radeon/ci: add uvd/vce info to dpm debugfs output
drm/radeon: export reservation_object from dmabuf to ttm
drm/radeon: cope with foreign fences inside the reservation object
drm/radeon: cope with foreign fences inside display
drm/core: use helper to check driver features
drm/radeon/cik: write gfx ucode version to ucode addr reg
drm/radeon/si: print full CS when we hit a packet 0
drm/radeon: remove unecessary includes
drm/radeon/combios: declare legacy_connector_convert as static
drm/radeon/atombios: declare connector convert tables as static
drm/radeon: drop btc_get_max_clock_from_voltage_dependency_table
drm/radeon/dpm: drop clk/voltage dependency filters for BTC
drm/radeon/dpm: drop clk/voltage dependency filters for CI
drm/radeon/dpm: drop clk/voltage dependency filters for SI
drm/radeon/dpm: drop clk/voltage dependency filters for NI
drm/radeon: disable audio when we disable hdmi (v2)
drm/radeon: split audio enable between eg and r600 (v2)
...
They don't appear to be used anywhere... elsewhere uses R*_PTE_*.
master@linux:U:.% git grep PTE_ -- drivers/gpu/drm/radeon | grep -v _PTE_
master@linux:U:.% (kyle@redacted:~/linux)
./arch/arm64/include/asm/pgtable.h:27:0: note: this is the location of the previous definition
#define PTE_VALID (_AT(pteval_t, 1) << 0)
^
In file included from drivers/gpu/drm/radeon/r600_cs.c:31:0:
drivers/gpu/drm/radeon/r600d.h:48:0: warning: "PTE_VALID" redefined [enabled by default]
#define PTE_VALID (1 << 0)
^
In file included from ./arch/arm64/include/asm/io.h:29:0,
from include/linux/clocksource.h:19,
from include/clocksource/arm_arch_timer.h:19,
from ./arch/arm64/include/asm/arch_timer.h:27,
from ./arch/arm64/include/asm/timex.h:19,
from include/linux/timex.h:65,
<snip>
from include/drm/drmP.h:51,
from drivers/gpu/drm/radeon/r600_cs.c:29:
./arch/arm64/include/asm/pgtable.h:27:0: note: this is the location of the previous definition
#define PTE_VALID (_AT(pteval_t, 1) << 0)
^
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only the essentials, cause this hw generation is really buggy.
v2: start supporting RV670,RV620 and RV635 as well
v3: activate more workarounds
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: cleanup R600 support
v3: rebased on current drm-fixes-3.12
v4: rebased on drm-next-3.14
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: wake up PLL, set [VD]CLK_SRC, cleanup code
v3: handle RV670,RV635,RV620 as well
v4: merge rv6xx and rs780/rs880 code, fix ref divider mask
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes lockups due to CP read GPUVM faults when running piglit on Cape
Verde.
v2 (chk): apply the fix to R600+ as well, on CIK only the GFX CP has
a PFP, add more comments to R600 code, enable flushing again
v3: (agd5f): only apply to 7xx+. r6xx does not have the packet.
v4: (agd5f): split flush change into a separate patch, fix formatting
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Recent RE efforts revealed ops performed by fglrx during HDMI setup.
This mostly adds masks to r/w ops plus few single missing bits.
This has been tested for possible regressions on:
1) DCE2 HD2400 (RV610)
2) DCE3 HD3470 (RV620)
For a reference and details see:
https://bugzilla.kernel.org/show_bug.cgi?id=76231
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
What initially seemed to be a typo in fglrx (using register 0x740c
instead of 0x74dc) appeared to be a correct behavior. DCE3 has ACR and
CRC registers swapped which explains why we needed
WREG32(HDMI0_AUDIO_CRC_CONTROL + offset, 0x1000);
This has been tested for possible regressions on DCE3 HD3470 (RV620).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
There's not much information still available on
r6xx, so r6xx is based on guess-work.
v2: put behind module parameter
v3: add IGP check
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
on gm45/vlv. Since this is a testing-only feature it should ever hurt,
but I figured it'll help with regression-testing -fixes. So I left it
in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
conflict with the bdw stage 1 patches if I'd postpone this to -next.
It's only an relatively small interface rework, so shouldn't cause pain.
It's also been in my tree since almost 3 weeks already.
That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over
Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.
There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.
* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
drm/i915/vlv: use per-pipe backlight controls v2
drm/i915: make backlight functions take a connector
drm/i915: move opregion asle request handling to a work queue
drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
drm/i915: Make intel_dp_is_edp() less specific
drm/i915: Give names to the VBT child device type bits
drm/i915/vlv: enable HDA display audio for Valleyview2
drm/i915/dvo: call ->mode_set callback only when the port is running
drm/i915: avoid unclaimed registers when capturing the error state
drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
drm/i915: scramble reset support for DP port CRC on vlv
drm/i915: scramble reset support for DP port CRC on g4x
drm/i916: add "auto" pipe CRC source
...
Conflicts:
MAINTAINERS
drivers/gpu/drm/i915/intel_panel.c
drivers/gpu/drm/nouveau/core/subdev/mc/base.c
drivers/gpu/drm/radeon/atombios_encoders.c
drivers/gpu/drm/radeon/radeon_connectors.c
The FMT blocks control how data is sent from the backend
of the display pipe to to monitor. Proper set up of the
FMT blocks are required for 30bpp formats. Additionally,
dithering can be enabled on for better display with 18 and
24bpp displays. The exception is LVDS/eDP which atom
takes care of in the SelectCRTC_Source table. For now
just enable truncation until we test dithering more.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I keep making that one, so checked if I was the only one. Apparently
not.
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This updates the audio driver to the speaker allocation
block from the EDID. A similar change was just implemented
for DCE4-8.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to set the wallclock ratio and adjust the phase
and module registers appropriately. May fix problems
with audio timing at certain display timings.
v2: properly handle clocks below 24mhz
v3: rebase r600 changes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lighter weight than using the 3D engine.
v2: fix ring count
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for rv7xx asics. This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching
Set radeon.dpm=1 to enable.
v2: reduce stack usage
v3: fix 64 bit div
v4: fix state enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for rv6xx asics. This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching
Set radeon.dpm=1 to enable.
v2: remove duplicate line
v3: fix thermal interrupt check noticed by Jerome
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
This is required for certain advanced functionality.
v2: save/restore list takes dword offsets
v3: rebase on gpu reset changes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of duplicating the code over and over again, just use a single
function to handle the clock calculations.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Just everything needed to decode videos using UVD.
v6: just all the bugfixes and support for R7xx-SI merged in one patch
v7: UVD_CGC_GATE is a write only register, lockup detection fix
v8: split out VRAM fallback changes, remove support for RV770,
add support for HEMLOCK, add buffer sizes checks
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we attempt the reset the GPU, look at the status registers
to determine what blocks need to be reset.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After refactoring the _cs logic, we ended up with many
macros and constants that #define the same thing.
Clean'em up.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reviewed-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Checking of the second colorbuffer was skipped on r700, because
CB_TARGET_MASK was 0xf. With r600, CB_TARGET_MASK is changed to 0xff,
so we must set the number of samples of the second colorbuffer to 1 in order
to pass the CS checker.
The DRM version is bumped, because RESOLVE_BOX is always rejected without this
fix on r600.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MSAA is impossible without them.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Returns a snapshot of the GPU clock counter. Needed
for certain OpenGL extensions.
v2: agd5f
- address Jerome's comments
- add function documentation
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Print various CP register that have valuable informations regarding
GPU lockup.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Required for streamout. Bump drm minor.
Marek v2: fix pkt->count check
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- SMX_SAR_CTL0 needs to be programmed correctly to prevent
problems with memory exports in certain cases.
- VC_ENHANCE needs to be initialized on 6xx/7xx.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tiling group size is always 256bits on r6xx/r7xx/r8xx/9xx. Also fix and
simplify render backend map. This now properly sets up the backend map
on r6xx-9xx which should improve 3D performance.
Vadim benchmarked also:
Some benchmarks on juniper (5750), fullscreen 1920x1080,
first result - kernel 3.4.0+ (fb21affa), second - with these patches:
Lightsmark: 91 fps => 123 fps +35%
Doom3: 74 fps => 101 fps +36%
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Introduce special struct radeon_afmt for this purpose.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds register definitions for HDMI/DP audio on
DCE2/3/4/5 hardware.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For 6xx+. Required for mesa to use htile support for HiZ/HiS.
Userspace will check radeon version 2.14 with is bumped either
by tiling patch or stream out patch. This patch only add support
for htile relocation which should be enough for any userspace
to implement the hyperz (using htile buffer) feature.
v2: Jerome: Fix size checking for htile buffer.
v3: Jerome: Adapt on top of r600/evergreen cs checker changes,
also check htile surface in case only stencil is
present.
Signed-off-by: Pierre-Eric Pelloux-Prayer <pelloux@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The out of order execution of semaphore commands on
pre cayman asics doesn't work correctly and can
cause deadlocks, so turn it off for now.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
evergreen and northern island gpu needs more informations for 2D tiling
than previous r6xx/r7xx. Add field to tiling ioctl to allow userspace
to provide those.
The v8 cs checking change to track color view on r6xx/r7xx doesn't
affect old userspace as old userspace always emited 0 for this register.
v2 fix r6xx/r7xx 2D tiling computation
v3 fix r6xx/r7xx height align for untiled surface & add support for
tile split on evergreen and newer
v4 improve tiling debugging output
v5 fix tile split code for evergreen and newer
v6 set proper tile split for crtc register
v7 fix tile split limit value
v8 add COLOR_VIEW checking to r6xx/r7xx checker, add evergreen cs
checking, update safe reg for r600, evergreen and cayman.
Evergreen checking need some work around for stencil alignment
issues
v9 fix tile split value range, fix compressed texture handling and
mipmap calculation, allow evergreen check to be silencious in
front of current broken userspace (depth/stencil alignment issue)
v10 fix eg 3d texture and compressed texture, fix r600 depth array,
fix r600 color view computation, add support for evergreen stencil
split
v11 more verbose debugging in some case
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
v2: agd5f: add strmout CS checking, copy_dw register checking
v3: agd5f: don't use cs_check_reg() for copy_dw checking as it
will incorrectly patch the command stream for certain regs.
v4: agd5f: add warning if safe reg check fails for copy_dw
v5: agd5f: add stricter checking for 6xx/7xx
v6: agd5f: add range checking for copy_dw on eg+,
add sx_surface_sync to safe reg list for 7xx.
v7: agd5f: add stricter checking for eg+
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
They are used to sync between rings, while fences
sync between a ring and the cpu.
v2 Fix radeon_semaphore_driver_fini when no semaphore were
allocated.
v3 Initialize list early on to avoid issue in case or early
error
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds
Alex Deucher
Kyle McMartin
Christian König
Rafał Miłecki
Dave Airlie
Damien Lespiau
Samuel Li
Christian König
Ilija Hadzic
Marek Olšák
Jerome Glisse