This patch fixes the wrong width of PINCFG_TYPE_DRV bitfields for Exynos5433
because PINCFG_TYPE_DRV of Exynos5433 has 4bit fields in the *_DRV
registers. Usually, other Exynos have 2bit field for PINCFG_TYPE_DRV.
Fixes: 3c5ecc9ed3 ("pinctrl: exynos: Add support for Exynos5433")
Cc: stable@vger.kernel.org
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl_gpio_request is called with the "full" gpio number, already
containing the base, then meson_pmx_request_gpio is then called with the
final pin number.
Remove the base addition when calling meson_pmx_disable_other_groups.
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
CC: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the function amd_gpio_irq_set_type, read the values from
the ACPI table to set the level and drop the settings passed
by the client.
Cc: <stable@vger.kernel.org> # 4.8.x+
Reviewed-by: Pankaj Sen <Pankaj.Sen@amd.com>
Reviewed-by: Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com>
Reviewed-by: Shah, Nehal-bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Shyam-sundar S-k <Shyam-sundar.S-k@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where things
come together.
We get a DT descriptions for a couple of new SoCs, all of them variants
of other chips we already support, and usually coming with a new
evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers
or industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on
Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it into
products and have served their purpose in the kernel as a template
for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree
Conflicts:
arch/arm/boot/dts/r8a*.dtsi: a node was added
the clk tree, keep both sides and watch out for git
dropping the required '};' at the end of each side.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wJt3
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
No core changes this time. Mainly gradual improvement and
feature growth in the drivers.
New drivers:
- New driver for TI DA850/OMAP-L138/AM18XX pinconf
- The SX150x was moved over from the GPIO subsystem and
reimagined as a pin control driver with GPIO support
in a joint effort by three independent users of this
hardware. The result was amazingly good!
- New subdriver for the Oxnas OX820
Improvements:
- The sunxi driver now supports the generic pin control
bindings rather than the sunxi-specific. Add debouncing
support to the driver.
- Simplifications in pinctrl-single adding a generic parser.
- Two downstream fixes and move the Raspberry Pi BCM2835 over
to use the generic GPIOLIB_IRQCHIP.
-----BEGIN PGP SIGNATURE-----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=Pkzu
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates from Linus Walleij:
"Bulk pin control changes for the v4.10 kernel cycle:
No core changes this time. Mainly gradual improvement and
feature growth in the drivers.
New drivers:
- New driver for TI DA850/OMAP-L138/AM18XX pinconf
- The SX150x was moved over from the GPIO subsystem and reimagined as
a pin control driver with GPIO support in a joint effort by three
independent users of this hardware. The result was amazingly good!
- New subdriver for the Oxnas OX820
Improvements:
- The sunxi driver now supports the generic pin control bindings
rather than the sunxi-specific. Add debouncing support to the
driver.
- Simplifications in pinctrl-single adding a generic parser.
- Two downstream fixes and move the Raspberry Pi BCM2835 over to use
the generic GPIOLIB_IRQCHIP"
* tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (92 commits)
pinctrl: sx150x: use new nested IRQ infrastructure
pinctrl: sx150x: handle missing 'advanced' reg in sx1504 and sx1505
pinctrl: sx150x: rename 'reg_advance' to 'reg_advanced'
pinctrl: sx150x: access the correct bits in the 4-bit regs of sx150[147]
pinctrl: mt8173: set GPIO16 to usb iddig mode
pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP
pinctrl: New driver for TI DA850/OMAP-L138/AM18XX pinconf
devicetree: bindings: pinctrl: Add binding for ti,da850-pupd
Documentation: pinctrl: palmas: Add ti,palmas-powerhold-override property definition
pinctrl: intel: set default handler to be handle_bad_irq()
pinctrl: sx150x: add support for sx1501, sx1504, sx1505 and sx1507
pinctrl: sx150x: sort chips by part number
pinctrl: sx150x: use correct registers for reg_sense (sx1502 and sx1508)
pinctrl: imx: fix imx_pinctrl_desc initialization
pinctrl: sx150x: support setting multiple pins at once
pinctrl: sx150x: various spelling fixes and some white-space cleanup
pinctrl: mediatek: use builtin_platform_driver
pinctrl: stm32: use builtin_platform_driver
pinctrl: sunxi: Testing the wrong variable
pinctrl: nomadik: split up and comments MC0 pins
...
Core changes:
- Simplify threaded interrupt handling: instead of passing
numbed parameters to gpiochip_irqchip_add_chained() we
create a new call: gpiochip_irqchip_add_nested() so the two
types are clearly semantically different. Also make sure
that all nested chips call gpiochip_set_nested_irqchip()
which is necessary for IRQ resend to work properly if
it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so
that anything != 0 will be send down to the driver as "1"
not the value passed in.
- ACPI can now support naming of GPIO lines, hogs and holes
in the GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem
and was moved over to a combined GPIO+pinctrl driver in the
pinctrl subsystem.
New features:
- Various cleanups to various drivers.
-----BEGIN PGP SIGNATURE-----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=2UpT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Luinus Walleij:
"Bulk GPIO changes for the v4.10 kernel cycle:
Core changes:
- Simplify threaded interrupt handling: instead of passing numbed
parameters to gpiochip_irqchip_add_chained() we create a new call:
gpiochip_irqchip_add_nested() so the two types are clearly
semantically different. Also make sure that all nested chips call
gpiochip_set_nested_irqchip() which is necessary for IRQ resend to
work properly if it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so that
anything != 0 will be send down to the driver as "1" not the value
passed in.
- ACPI can now support naming of GPIO lines, hogs and holes in the
GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem and was
moved over to a combined GPIO+pinctrl driver in the pinctrl
subsystem.
New features:
- Various cleanups to various drivers"
* tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (49 commits)
gpio: merrifield: Implement gpio_get_direction callback
gpio: merrifield: Add support for hardware debouncer
gpio: chardev: Return error for seek operations
gpio: arizona: Tidy up probe error path
gpio: arizona: Remove pointless set of platform drvdata
gpio: pl061: delete platform data handling
gpio: pl061: move platform data into driver
gpio: pl061: rename variable from chip to pl061
gpio: pl061: rename state container struct
gpio: pl061: use local state for parent IRQ storage
gpio: set explicit nesting on drivers
gpio: simplify adding threaded interrupts
gpio: vf610: use builtin_platform_driver
gpio: axp209: use correct register for GPIO input status
gpio: stmpe: fix interrupt handling bug
gpio: em: depnd on ARCH_SHMOBILE
gpio: zx: depend on ARCH_ZX
gpio: x86: update config dependencies for x86 specific hardware
gpio: mb86s7x: use builtin_platform_driver
gpio: etraxfs: use builtin_platform_driver
...
Use the new gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip() calls to properly created
a nested irqchip and mark all child irqs properly with
their parent IRQ.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes a problem where sx150x_regmap_reg_width() returns 8 for the
data register (reg 0) for sx1504 where it should return 4, and return
a correct 8 for sx1505 but for the wrong reason (both chips lack the
'advanced' register). This is not a real problem, since nothing depends
on the function returning 4 or 8, and certainly not if it is returning
8 for the wrong reason. But fix this to avoid nasty surprises down the
line.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This matches the datasheets and is less confusing since the register
has nothing to with advancing anything.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The code assumes 8-bit or 16-bit width registers, but three of the
chips (sx1501/sx1504/sx1507) are 4-bit. So, try to handle 4-bit chips as
well, they leave the high part of each register unused.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the default mode of GPIO16 pin is gpio, when set EINT16 to
IRQ_TYPE_LEVEL_HIGH, no interrupt is triggered, it can be
fixed when set its default mode as usb iddig.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It should be possible to use the GPIOLIB_IRQCHIP helper
library with the BCM2835 driver since it is a pretty straight
forward cascaded irqchip.
The only difference from other drivers is that the BCM2835
has several banks for a single gpiochip, and each bank has
a separate IRQ line. Instead of creating one gpiochip per
bank, a single gpiochip covers all banks GPIO lines. This
makes it necessary to resolve the bank ID in the IRQ
handler.
The GPIOLIB_IRQCHIP allows several IRQs to be cascaded off
the same gpiochip by calling gpiochip_set_chained_irqchip()
repeatedly, but we have been a bit short on examples
for how this should be handled in practice, so this is intended
as an example of how this can be achieved.
The old code did not model the chip as a chained interrupt
handler, but this patch also rectifies that situation.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Eric Anholt <eric@anholt.net>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a new driver for pinconf on TI DA850/OMAP-L138/AM18XX. These
SoCs have a separate controller for controlling pullup/pulldown groups.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We switch the default handler to be handle_bad_irq() instead of
handle_simple_irq() (which was not correct anyway).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
please pull the following:
- Rafal adds support for the Netgear R8500 routers, adds basic support
for the Tenda AC9 router which uses the new BCM53573 SoC (single core Cortex
A7). He also enables the UART on the Netgear R8000 and restructures the
include files a bit for the BCM47094 SoC, finally he adds USB 3.0 PHY nodes
which enables USB 3.0 on BCM5301X devices that support it. Finally he adds
support for the TP-LINK Archer C9 V1 router.
- Kamal adds support for the QSPI controller on the Northstar Plus SoCs and updates
the bcm958625k reference board to have it enabled
- Dan adds support for the Luxul XAP-1510 (using a BCM4708) and XWR-3100 (using
a BCM47094)
- Scott fixes the pinctrl names in the Cygnus DTS files
- Jonathan enables the Broadcom iProc mailbox controller for Broadcom Cygnus/iProc
SoCs, he adds interrupt support for the GPIO CRMU hardware block and finally adds
the node for the OTP controller found on Cygnus SoCs
- Dhananjay enables the GPIO B controller on Norstarh Plus SoCs
- Eric defines standard pinctrl groups in the BCM2835 GPIO node
- Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
to use their appropriate pinctrl functions
- Linus adds names for the Raspberry Pi GPIO lines based on the datasheet
- Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block
- Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
Device Tree nodes he also fixes the Raspberry Pi GPIO lines names and finally
adds names for the Raspberry Zero GPIO lines
-----BEGIN PGP SIGNATURE-----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=4GFQ
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.10/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.10" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoC Device Tree changes for 4.10,
please pull the following:
- Rafal adds support for the Netgear R8500 routers, adds basic support
for the Tenda AC9 router which uses the new BCM53573 SoC (single core Cortex
A7). He also enables the UART on the Netgear R8000 and restructures the
include files a bit for the BCM47094 SoC, finally he adds USB 3.0 PHY nodes
which enables USB 3.0 on BCM5301X devices that support it. Finally he adds
support for the TP-LINK Archer C9 V1 router.
- Kamal adds support for the QSPI controller on the Northstar Plus SoCs and updates
the bcm958625k reference board to have it enabled
- Dan adds support for the Luxul XAP-1510 (using a BCM4708) and XWR-3100 (using
a BCM47094)
- Scott fixes the pinctrl names in the Cygnus DTS files
- Jonathan enables the Broadcom iProc mailbox controller for Broadcom Cygnus/iProc
SoCs, he adds interrupt support for the GPIO CRMU hardware block and finally adds
the node for the OTP controller found on Cygnus SoCs
- Dhananjay enables the GPIO B controller on Norstarh Plus SoCs
- Eric defines standard pinctrl groups in the BCM2835 GPIO node
- Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
to use their appropriate pinctrl functions
- Linus adds names for the Raspberry Pi GPIO lines based on the datasheet
- Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block
- Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
Device Tree nodes he also fixes the Raspberry Pi GPIO lines names and finally
adds names for the Raspberry Zero GPIO lines
* tag 'arm-soc/for-4.10/devicetree' of http://github.com/Broadcom/stblinux: (29 commits)
ARM: bcm2835: Add names for the RPi Zero GPIO lines
ARM: bcm2835: Fix names for the Raspberry Pi GPIO lines
ARM: dts: enable GPIO-b for Broadcom NSP
ARM: BCM5301X: Add DT for TP-LINK Archer C9 V1
ARM: dts: Add node for Broadcom OTP controller driver
ARM: dts: Enable interrupt support for cygnus crmu gpio driver
ARM: dts: Enable Broadcom iProc mailbox controller
ARM: bcm2835: Add names for the Raspberry Pi GPIO lines
ARM: bcm2835: dts: add thermal node to device-tree of bcm283x
dt: bindings: add thermal device driver for bcm2835
ARM: dts: bcm283x: fix typo in mailbox address
DT: binding: bcm2835-mbox: fix address typo in example
ARM: dts: cygnus: fix naming of pinctrl node
ARM: BCM53573: Specify PMU and its ILP clock in the DT
ARM: BCM5301X: Add DT for Luxul XWR-3100
ARM: BCM5301X: Add DT for Luxul XAP-1510
ARM: BCM5301X: Specify USB 3.0 PHY in DT
ARM: BCM5301X: Enable UART on Netgear R8000
ARM: BCM5301X: Add separated DTS include file for BCM47094
ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes
...
All other registers on these chips are 8-bit, but reg_sense is 16-bits
and therefore needs to be moved down one notch.
This was apparently overlooked in the conversion to regmap, which only
updated the register locations for the 16-bit chips.
Fixes: 6489677f86 ("pinctrl-sx150x: Replace sx150x_*_cfg by means of regmap API")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the chip does not have an oscio pin, all pins are configured in
the same regmap register making it trivial to update all pins at
once, so do that. If an oscio pin is present, there needs to be
more locking in place to handle all cases correctly, so this is
skipped.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Smatch complains that we dereference "map" before testing it for NULL
which is true. We should be testing "*map" instead. Also on the error
path, we should free *map and set it to NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should return -ENOMEM instead of success if pcs_add_function() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gcc warns about a way that it could use an uninitialized variable:
drivers/pinctrl/sunxi/pinctrl-sunxi.c: In function 'sunxi_pinctrl_init':
drivers/pinctrl/sunxi/pinctrl-sunxi.c:1191:8: error: 'best_div' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This cannot really happen except if 'freq' is UINT_MAX and 'clock' is
zero, and both of these are forbidden. To shut up the warning anyway,
this changes the logic to initialize the return code to the first
divider value before looking at the others.
Fixes: 7c926492d3 ("pinctrl: sunxi: Add support for interrupt debouncing")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- DU and EtherAVB pin groups for R-Car M3-W,
- Bias handling cleanups and bug fixes,
- Drive-strength for non-GPIO pins for R-Car H3,
- EtherAVB MDIO & MII, and QSPI pin groups for R-Car H3.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Mv9x
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.10-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.10 (take two)
- DU and EtherAVB pin groups for R-Car M3-W,
- Bias handling cleanups and bug fixes,
- Drive-strength for non-GPIO pins for R-Car H3,
- EtherAVB MDIO & MII, and QSPI pin groups for R-Car H3.
This add pinctrl support for Rockchip RK1108 Soc.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Series-changes: 2
- add pull and drive-strength functionality
Series-changes: 3
- two minor CodingStyle fixes adviced by Heiko
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Group the QSPI0 and QSPI1 pins into similar groups found in other sh-pfc
drivers. The pins can not be muxed between functions other than QSPI,
but their drive strength can be controlled.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Group the AVB pins into similar groups found in other sh-pfc drivers.
The pins can not be muxed between functions other then AVB but their
drive strength can be controlled.
The group avb_mdc containing ADV_MDC and ADV_MDIO are on other SoCs
called avb_mdio. In pfc-r8a7795 the avb_mdc group already existed and
is in use in DT. Therefore add the ADV_MDIO pin to the existing group
instead of renaming it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are pins on the r8a7795 which are not part of a GPIO bank nor
can be muxed between different functions. They do however allow for the
drive-strength to be configured. Add those pins to the list of pins and
to the drive-strength configuration registers.
The pins can now be referred to in DT by function names and their
drive-strength modified.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pins not associated with a GPIO port can still have other configuration
parameters. Add a new macro SH_PFC_PIN_NAMED_CFG which allows for named
pins to be declared with a set of configurations. The new macro is an
modification of SH_PFC_PIN_NAMED to allow for optional configuration to
be assigned.
The flag SH_PFC_PIN_CFG_NO_GPIO is still enforced as this should only be
used to define pins not associated with a GPIO port.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Change the data structure and use the generic sh_pfc_pin_to_bias_info()
function to get the register offset and bit information.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There is a bug in the r8a7795 bias code where a WARN() is trigged
anytime a pin from PUEN0/PUD0 is accessed.
# cat /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins
WARNING: CPU: 2 PID: 2391 at drivers/pinctrl/sh-pfc/pfc-r8a7795.c:5364 r8a7795_pinmux_get_bias+0xbc/0xc8
[..]
Call trace:
[<ffff0000083c442c>] r8a7795_pinmux_get_bias+0xbc/0xc8
[<ffff0000083c37f4>] sh_pfc_pinconf_get+0x194/0x270
[<ffff0000083b0768>] pin_config_get_for_pin+0x20/0x30
[<ffff0000083b11e8>] pinconf_generic_dump_one+0x168/0x188
[<ffff0000083b144c>] pinconf_generic_dump_pins+0x5c/0x98
[<ffff0000083b0628>] pinconf_pins_show+0xc8/0x128
[<ffff0000081fe3bc>] seq_read+0x16c/0x420
[<ffff00000831a110>] full_proxy_read+0x58/0x88
[<ffff0000081d7ad4>] __vfs_read+0x1c/0xf8
[<ffff0000081d8874>] vfs_read+0x84/0x148
[<ffff0000081d9d64>] SyS_read+0x44/0xa0
[<ffff000008082f4c>] __sys_trace_return+0x0/0x4
This is due to the WARN() check if the reg field of the pullups struct
is zero, and this should be 0 for pins controlled by the PUEN0/PUD0
registers since PU0 is defined as 0. Change the data structure and use
the generic sh_pfc_pin_to_bias_info() function to get the register
offset and bit information.
Fixes: 560655247b ("pinctrl: sh-pfc: r8a7795: Add bias pinconf support")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The last else statement is missing braces, and the indentation level can
be reduced.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On some SoC there are no simple mapping of pins to bias register bits
and a lookup table is needed. This logic is already implemented in some
SoC specific drivers that could benefit from a generic implementation.
Add helpers to deal with the lookup which later can be used by the SoC
specific drivers. The logic used to lookup are different from the one it
aims to replace, this is intentional. This new method reduces the memory
consumption at the cost of increased CPU usage and fix a bug where a
WARN() would incorrectly be triggered if the register offset is 0.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Always stating PIN_CONFIG_BIAS_DISABLE is supported gives untrue output
when examining /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins if
the operation get_bias() is implemented but the pin is not handled by
the get_bias() implementation. In that case the output will state that
"input bias disabled" indicating that this pin has bias control
support.
Make support for PIN_CONFIG_BIAS_DISABLE depend on that the pin either
supports SH_PFC_PIN_CFG_PULL_UP or SH_PFC_PIN_CFG_PULL_DOWN. This also
solves the issue where SoC specific implementations print error messages
if their particular implementation of {set,get}_bias() is called with a
pin it does not know about.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Only the DU parallel RGB output signals are included, HDMI and TCON pins
will be added in separate groups. Based on a similar patch from Laurent
Pinchart for the r8a7795 PFC driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The pin controller found in the Allwinner SoCs has support for interrupts
debouncing.
However, this is not done per-pin, preventing us from using the generic
pinconf binding for that, but per irq bank, which, depending on the SoC,
ranges from one to five.
Introduce a device-wide property to deal with this using a microsecond
resolution. We can re-use the per-pin input-debounce property for that, so
let's do it!
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sunxi_pconf_reg helper introduced in the last patch gives us the
chance to rework sunxi_pconf_group_set to have it match the structure
of sunxi_pconf_(group_)get and make it easier to understand.
For each config to set, it:
1. checks if the parameter is supported.
2. checks if the argument is within limits.
3. converts argument to the register value.
4. writes to the register with spinlock held.
As a result the function now blocks unsupported config parameters,
instead of silently ignoring them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sunxi pinctrl driver only caches whatever pinconf setting was last
set on a given pingroup. This is not particularly helpful, nor is it
correct.
Fix this by actually reading the hardware registers and returning
the correct results or error codes. Also filter out unsupported
pinconf settings. Since this driver has a peculiar setup of 1 pin
per group, we can support both pin and pingroup pinconf setting
read back with the same code. The sunxi_pconf_reg helper and code
structure is inspired by pinctrl-msm.
With this done we can also claim to support generic pinconf, by
setting .is_generic = true in pinconf_ops.
Also remove the cached config value. The behavior of this was never
correct, as it only cached 1 setting instead of all of them. Since
we can now read back settings directly from the hardware, it is no
longer required.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to pinconf-generic.h, the argument for
PIN_CONFIG_BIAS_PULL_{DOWN,UP} is non-zero if the bias is enabled
with a pull up/down resistor, zero if it is directly connected
to VDD or ground.
Since Allwinner hardware uses a weak pull resistor internally,
the argument should be 1.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the recently refactored sunxi pinctrl library, we are only allocating
one set of pin configs for each pinmux setting node. When the pinctrl_map
structure is freed, the pin configs should also be freed. However the
code assumed the first map would contain the configs, which actually
never happens, as the mux function map gets added first.
The proper way to do this is to look through all the maps and free the
first one whose type is actually PIN_MAP_TYPE_CONFIGS_GROUP.
Also slightly expand the comment explaining this.
Fixes: f233dbca62 ("pinctrl: sunxi: Rework the pin config building code")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate, meaning
that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get the exact same change, so they are handled in batch.
Changes are (1) use builtin_platform_driver, (2) use init.h header
(3) delete module_exit related code, (4) delete MODULE_DEVICE_TABLE,
(5) delete MODULE_LICENCE/MODULE_AUTHOR and associated tags and (6)
drop ".remove" code and prevent sysfs unbind attempts to call ".remove".
Once this is done, the shared remove function in wmt.[ch] is no longer
used and hence it is removed as well.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE etc. tags since all that information
is already contained at the top of each file in the comments.
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch add the support of GPF[1-5] pin of Exynos5433 SoC. The GPFx need
to support the multiple memory map because the registers of GPFx are located
in the different domain.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch supports the multiple IORESOURCE_MEM resources for one pin-bank.
In the pre-existing Exynos series, the registers of the gpio bank are included
in the one memory map. But, some gpio bank need to support the one more memory
map (IORESOURCE_MEM) because the registers of gpio bank are separated into
the different memory map.
For example,
The both ALIVE and IMEM domain have the different memory base address.
The GFP[1-5] of exynos5433 are composed as following:
- ALIVE domain : WEINT_* registers
- IMEM domain : CON/DAT/PUD/DRV/CONPDN/PUDPDN register
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-gpio@vger.kernel.org
Suggested-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When dynamically unloading overlays, it is important that freed pins are
restored to being inputs to prevent functions from being enabled in
multiple places at once.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Contrary to the documentation, the BCM2835 GPIO controller actually
has four interrupt lines - one each for the three IRQ groups and one
common. Confusingly, the GPIO interrupt groups don't correspond
directly with the GPIO control banks. Instead, GPIOs 0-27 generate IRQ
GPIO0, 28-45 IRQ GPIO1 and 46-53 IRQ GPIO2.
Awkwardly, the GPIOs for IRQ GPIO1 straddle two 32-entry GPIO banks,
so split out a function to process the interrupts for a single GPIO
bank.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Chanwoo Choi
Neil Armstrong
Shyam Sundar S K
Linus Torvalds
Linus Walleij
Peter Rosin
Chunfeng Yun
David Lechner
Andy Shevchenko
Arnd Bergmann
Gary Bisson
Geliang Tang
Dan Carpenter
Andy Yan
Niklas Söderlund
Takeshi Kihara
Maxime Ripard
Chen-Yu Tsai
Paul Gortmaker
Phil Elwell