I get report from customer that his usb-serial
converter doesn't work well,it sometimes work,
but sometimes it doesn't.
The usb-serial converter's id:
vendor_id product_id
0x4348 0x5523
Then I search the usb-serial codes, and there are
two drivers announce support this device, pl2303
and ch341, commit 026dfaf1 cause it. Through many
times to test, ch341 works well with this device,
and pl2303 doesn't work quite often(it just work quite little).
ch341 works well with this device, so we doesn't
need pl2303 to support.I try to revert 026dfaf1 first,
but it failed. So I prepare this patch by hand to revert it.
Signed-off-by: Wang YanQing <Udknight@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On October 1 in 2011,
OKI SEMICONDUCTOR Co., Ltd. changed the company name in to LAPIS Semiconductor Co., Ltd.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 8020i protocol (also 8070i and QIC-157) uses 12-byte commands;
shorter commands must be padded. Simon Detheridge reports that his
3-TB USB disk drive claims to use the 8020i protocol (which is
normally meant for ATAPI devices like CD drives), and because of its
large size, the disk drive requires the use of 16-byte commands.
However the usb_stor_pad12_command() routine in usb-storage always
sets the command length to 12, making the drive impossible to use.
Since the SFF-8020i specification allows for 16-byte commands in
future extensions, we may as well accept them. This patch (as1490)
changes usb_stor_pad12_command() to leave commands larger than 12
bytes alone rather than truncating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Simon Detheridge <simon@widgit.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch contains additional affected webcam models, on top of the
patches commited to linux-next 2394d67e44
and 5b253d88cc
Signed-off-by: sordna <sordna@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below are codes for accessing usb sysif_regs in driver:
usb_sys_regs = (struct usb_sys_interface *)
((u32)dr_regs + USB_DR_SYS_OFFSET);
these codes work in 32-bit, but in 64-bit, use u32 to type cast the address
of ioremap is not right, and accessing members of 'usb_sys_regs' will cause
call trace, so use (void *) for both 32-bit and 64-bit.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in commit aa6e52a35 we introduce the support of overcurrent notification
but the set and get of the power without checking if the gpio is valid or not
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a race between the USB disconnect handler and the TTY close
handler which may cause the acm object to be freed while it's still
being used. This may lead to things like
http://article.gmane.org/gmane.linux.usb.general/54250
and
https://lkml.org/lkml/2011/5/29/64
This is the simplest fix I could come up with. Holding on to open_mutex
while closing the TTY device prevents acm_disconnect() from freeing the
acm object between acm->port.count drops to 0 and the TTY side of the
cleanups are finalized.
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We've had another report of the "chipmunk" sound on a Logitech C600 webcam.
This patch resolves the issue.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current TT scheduling doesn't allow to play and then record on a
full-speed device connected to a high speed hub.
The IN iso stream can only start on the first uframe (0-2 for a 165 us)
because of CSPLIT transactions.
For the OUT iso stream there no such restriction. uframe 0-5 are possible.
The idea of this patch is that the first uframe are precious (for IN TT iso
stream) and we should allocate the last uframes first if possible.
For that we reverse the order of uframe allocation (last uframe first).
Here an example :
hid interrupt stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 0 | 0 | 0 | 0 | 0 | 0 |
----------------------------------------------------------------------
iso OUT stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 125 | 39 | 0 | 0 | 0 | 0 | 0 |
----------------------------------------------------------------------
There no place for iso IN stream (uframe 0-2 are used) and we got "cannot
submit datapipe for urb 0, error -28: not enough bandwidth" error.
With the patch this become.
iso OUT stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 0 | 0 | 125 | 39 | 0 | 0 |
----------------------------------------------------------------------
iso IN stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 125 | 40 | 125 | 39 | 0 | 0 |
----------------------------------------------------------------------
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Signed-off-by: Thomas Poussevin <thomas.poussevin@parrot.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1494) fixes a problem in xhci-hcd's resume routine.
When the controller is runtime-resumed, this can only mean that one of
the two root hubs has made a wakeup request and therefore needs to be
resumed as well. Rather than try to determine which root hub requires
attention (which might be difficult in the case where a new
non-SuperSpeed device has been plugged in), the patch simply resumes
both root hubs.
Without this change, there is a race: The controller might be put back
to sleep before it can activate its IRQ line, and the wakeup condition
might never get handled.
The patch also simplifies the logic in xhci_resume a little, combining
some repeated flag settings into a single pair of statements.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1491) works around a bug in GCC-3.4.6, which is still
supposed to be supported. The number of microseconds in the udelay()
call in quirk_usb_disable_ehci() is fixed at 100, but the compiler
doesn't understand this and generates a link-time error. So we
replace the otherwise unused variable "delta" with a simple constant
100. This same pattern is already used in other delay loops in that
source file.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Konrad Rzepecki <krzepecki@dentonet.pl>
Tested-by: Konrad Rzepecki <krzepecki@dentonet.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch for the usb serial ark3116 driver fixes an initialisation
ordering bug that gets triggered on hotplug when using at least recent
debian/ubuntu userspace. Without it, ark3116 serial cables don't work.
Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Tested-by: law_ence.dev@ntlworld.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit de47725 (include: replace linux/module.h
with "struct module" wherever possible) introduced
a compilation breaked when it removed <linux/module.h>
from <linux/device.h> which musb glue layers were
(mistakenly) relying on.
Include that header to fix the compile error.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this the gadget will never be able to allocate a stream capable
endpoint. The manual says that the stream id is a 16bit id. It does not
talk about an upper limit in any other way. So I think 15 is a
reasonable limit :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
new endpoint should start from DATA0,
but mod_host didn't care it.
This patch fix it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
renesas_usbhs is caring pipe type and its direction.
but current usbhs_endpoint_alloc() didn't check direction.
this patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit "193ab2a usb: gadget: allow multiple gadgets to be built"
the udc controllers can be compiled as a module. The ci13xxx_msm driver
is missing the MODULE_LICENSE statement, so loading fails with:
ci13xxx_msm: module license 'unspecified' taints kernel.
ci13xxx_msm: Unknown symbol dev_set_name (err 0)
ci13xxx_msm: Unknown symbol platform_get_irq (err 0)
ci13xxx_msm: Unknown symbol device_unregister (err 0)
ci13xxx_msm: Unknown symbol usb_add_gadget_udc (err 0)
ci13xxx_msm: Unknown symbol put_device (err 0)
ci13xxx_msm: Unknown symbol platform_driver_register (err 0)
ci13xxx_msm: Unknown symbol platform_get_resource (err 0)
ci13xxx_msm: Unknown symbol device_register (err 0)
ci13xxx_msm: Unknown symbol usb_del_gadget_udc (err 0)
This patch adds the missing MODULE_LICENSE statement with GPL v2 according
to the header of the driver.
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following compile errors that show up if switching
on the debug trace code:
drivers/usb/gadget/ci13xxx_udc.c: In function 'ci13xxx_wakeup':
drivers/usb/gadget/ci13xxx_udc.c:2517:3: error: 'dev' undeclared (first use in this function)
drivers/usb/gadget/ci13xxx_udc.c:2517:3: note: each undeclared identifier is reported only once for each function it appears in
drivers/usb/gadget/ci13xxx_udc.c: In function 'udc_probe':
drivers/usb/gadget/ci13xxx_udc.c:2867:2: error: 'name' undeclared (first use in this function)
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The inline documentation of _gadget_stop_activity() states that the
function should be called holding the udc->lock. This however will
result in a deadlock, because _gadget_stop_activity() takes the udc->lock.
During normal operation _gadget_stop_activity() is always called unlocked,
but in ci13xxx_stop() it's called locked, this results in the following
deadlock during rmmod of a gadget driver.
This patch fixes the deadlock by calling _gadget_stop_activity() always
unlocked, the inline documentation is adjusted accordingly.
=============================================
[ INFO: possible recursive locking detected ]
3.1.0-rc6+ #159
---------------------------------------------
rmmod/121 is trying to acquire lock:
(udc_lock){-.-...}, at: [<c0229048>] _gadget_stop_activity+0x18/0x154
but task is already holding lock:
(udc_lock){-.-...}, at: [<c02291e0>] ci13xxx_stop+0x5c/0x164
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(udc_lock);
lock(udc_lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by rmmod/121:
#0: (udc_lock#2){+.+.+.}, at: [<c02286c0>] usb_gadget_unregister_driver+0x34/0x88
#1: (udc_lock){-.-...}, at: [<c02291e0>] ci13xxx_stop+0x5c/0x164
stack backtrace:
[<c000d41c>] (unwind_backtrace+0x0/0xf0) from [<c0056f94>] (check_deadlock.clone.24+0x284/0x2c4)
[<c0056f94>] (check_deadlock.clone.24+0x284/0x2c4) from [<c00589ac>] (validate_chain.clone.25+0x430/0x6fc)
[<c00589ac>] (validate_chain.clone.25+0x430/0x6fc) from [<c0059bac>] (__lock_acquire+0x494/0x8f0)
[<c0059bac>] (__lock_acquire+0x494/0x8f0) from [<c005a698>] (lock_acquire+0x98/0x1a8)
[<c005a698>] (lock_acquire+0x98/0x1a8) from [<c02f12a4>] (_raw_spin_lock_irqsave+0x64/0xa0)
[<c02f12a4>] (_raw_spin_lock_irqsave+0x64/0xa0) from [<c0229048>] (_gadget_stop_activity+0x18/0x154)
[<c0229048>] (_gadget_stop_activity+0x18/0x154) from [<c0229234>] (ci13xxx_stop+0xb0/0x164)
[<c0229234>] (ci13xxx_stop+0xb0/0x164) from [<c022867c>] (usb_gadget_remove_driver+0x88/0x98)
[<c022867c>] (usb_gadget_remove_driver+0x88/0x98) from [<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88)
[<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88) from [<c0065f2c>] (sys_delete_module+0x1fc/0x26c)
[<c0065f2c>] (sys_delete_module+0x1fc/0x26c) from [<c00092a0>] (ret_fast_syscall+0x0/0x38)
BUG: spinlock lockup on CPU#0, rmmod/121, c05b1644
[<c000d41c>] (unwind_backtrace+0x0/0xf0) from [<c01da000>] (do_raw_spin_lock+0x128/0x144)
[<c01da000>] (do_raw_spin_lock+0x128/0x144) from [<c02f12c8>] (_raw_spin_lock_irqsave+0x88/0xa0)
[<c02f12c8>] (_raw_spin_lock_irqsave+0x88/0xa0) from [<c0229048>] (_gadget_stop_activity+0x18/0x154)
[<c0229048>] (_gadget_stop_activity+0x18/0x154) from [<c0229234>] (ci13xxx_stop+0xb0/0x164)
[<c0229234>] (ci13xxx_stop+0xb0/0x164) from [<c022867c>] (usb_gadget_remove_driver+0x88/0x98)
[<c022867c>] (usb_gadget_remove_driver+0x88/0x98) from [<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88)
[<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88) from [<c0065f2c>] (sys_delete_module+0x1fc/0x26c)
[<c0065f2c>] (sys_delete_module+0x1fc/0x26c) from [<c00092a0>] (ret_fast_syscall+0x0/0x38)
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current driver sets the request's dma addr (mReq->req.dma) to 0 to
mark the DMA address as not valid. However some gadget drivers
(e.g. gadgetfs) set the request's dma addr to DMA_ADDR_INVALID to mark
the address as invalid. This leads to bogus data send because the
ci13xxx_udc driver assumes the request has already been mapped.
This patch fixes the problem, by using DMA_ADDR_INVALID instead of 0
to mark the request's DMA address as invalid.
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Under certain circumstances lockdep finds an inconsistent lock state in
gadgetfs. The problem can be reproduced with a hardware using the
ci13xxx_udc driver and the gadgetfs test program (needs a patch to support
the ci13xxx_udc, though):
http://www.linux-usb.org/gadget/usb.c
Start the test program, wait to initialize, then press Ctrl+c.
This patch fixes the following problem by using spin_lock_irqsave()
instead of spin_lock().
=================================
[ INFO: inconsistent lock state ]
3.1.0-rc6+ #158
---------------------------------
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
usb/113 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&(&dev->lock)->rlock){?.....}, at: [<bf000340>] gadgetfs_disconnect+0x14/0x80 [gadgetfs]
{IN-HARDIRQ-W} state was registered at:
[<c00596b8>] mark_irqflags+0x14c/0x1ac
[<c0059bf8>] __lock_acquire+0x4e0/0x8f0
[<c005a698>] lock_acquire+0x98/0x1a8
[<c02f10e0>] _raw_spin_lock+0x54/0x8c
[<bf000340>] gadgetfs_disconnect+0x14/0x80 [gadgetfs]
[<c0229104>] _gadget_stop_activity+0xd4/0x154
[<c022b130>] isr_reset_handler+0x34/0x1c0
[<c022c320>] udc_irq+0x204/0x228
[<c0069018>] handle_irq_event_percpu+0x64/0x3a0
[<c0069390>] handle_irq_event+0x3c/0x5c
[<c006ae5c>] handle_level_irq+0x8c/0x10c
[<c0068a34>] generic_handle_irq+0x30/0x44
[<c0009b2c>] handle_IRQ+0x30/0x84
[<c0008ef8>] __irq_svc+0x38/0x60
[<c0009c58>] default_idle+0x30/0x34
[<c0009e30>] cpu_idle+0x9c/0xd8
[<c04056f4>] start_kernel+0x278/0x2bc
irq event stamp: 6412
hardirqs last enabled at (6412): [<c02f1cd0>] _raw_spin_unlock_irqrestore+0x30/0x5c
hardirqs last disabled at (6411): [<c02f1278>] _raw_spin_lock_irqsave+0x20/0xa0
softirqs last enabled at (6381): [<c002833c>] irq_exit+0xa0/0xa8
softirqs last disabled at (6372): [<c002833c>] irq_exit+0xa0/0xa8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&dev->lock)->rlock);
<Interrupt>
lock(&(&dev->lock)->rlock);
*** DEADLOCK ***
1 lock held by usb/113:
#0: (udc_lock#2){+.+.+.}, at: [<c02286c0>] usb_gadget_unregister_driver+0x34/0x88
stack backtrace:
[<c000d41c>] (unwind_backtrace+0x0/0xf0) from [<c0058e98>] (print_usage_bug+0x144/0x1c4)
[<c0058e98>] (print_usage_bug+0x144/0x1c4) from [<c0059144>] (mark_lock_irq+0x22c/0x274)
[<c0059144>] (mark_lock_irq+0x22c/0x274) from [<c00592d4>] (mark_lock+0x148/0x3e0)
[<c00592d4>] (mark_lock+0x148/0x3e0) from [<c0059668>] (mark_irqflags+0xfc/0x1ac)
[<c0059668>] (mark_irqflags+0xfc/0x1ac) from [<c0059bf8>] (__lock_acquire+0x4e0/0x8f0)
[<c0059bf8>] (__lock_acquire+0x4e0/0x8f0) from [<c005a698>] (lock_acquire+0x98/0x1a8)
[<c005a698>] (lock_acquire+0x98/0x1a8) from [<c02f10e0>] (_raw_spin_lock+0x54/0x8c)
[<c02f10e0>] (_raw_spin_lock+0x54/0x8c) from [<bf000340>] (gadgetfs_disconnect+0x14/0x80 [gadgetfs])
[<bf000340>] (gadgetfs_disconnect+0x14/0x80 [gadgetfs]) from [<c0229104>] (_gadget_stop_activity+0xd4/0x154)
[<c0229104>] (_gadget_stop_activity+0xd4/0x154) from [<c0229240>] (ci13xxx_stop+0xbc/0x17c)
[<c0229240>] (ci13xxx_stop+0xbc/0x17c) from [<c022867c>] (usb_gadget_remove_driver+0x88/0x98)
[<c022867c>] (usb_gadget_remove_driver+0x88/0x98) from [<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88)
[<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88) from [<bf0003e8>] (dev_release+0x14/0x48 [gadgetfs])
[<bf0003e8>] (dev_release+0x14/0x48 [gadgetfs]) from [<c00cc158>] (__fput+0xa4/0x1f0)
[<c00cc158>] (__fput+0xa4/0x1f0) from [<c00c7f28>] (filp_close+0x5c/0x74)
[<c00c7f28>] (filp_close+0x5c/0x74) from [<c00c7fe8>] (sys_close+0xa8/0x150)
[<c00c7fe8>] (sys_close+0xa8/0x150) from [<c00092a0>] (ret_fast_syscall+0x0/0x38)
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The dynamic jack allocation of the MIDI gadget currently links all
external jacks to one single instance of an embedded jack. According to
the spec, this is only valid if these streams always carry the same data
stream, as described in the USB MIDI 1.0 spec, chapter 3.3.1.
Also, genius Windows 7(tm) terminates it's life cycle instantly with a
blue screen of death once a device with more than one input and output
port with the current implementation is connected.
While at it, and because it grew again by this change, allocate the
temporary function pointer list on the heap, not on the stack.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB-IF CV compliance tester is getting stricter, and it would
be valid for it to fail a mass-storage device that accepts an
invalid USB_BULK_RESET_REQUEST request. Although it doesn't do
that yet, let's be proactive and fix that now.
Suggested by Alan Stern.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The latest USB-IF CV tester checks for a valid length for this
request.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix up the following section mismatch warnings:
WARNING: drivers/usb/renesas_usbhs/renesas_usbhs.o(.text+0xf5d): Section
mismatch in reference from the function usbhs_mod_probe() to the function
.devinit.text:usbhs_mod_host_probe() The function usbhs_mod_probe() references
the function __devinit usbhs_mod_host_probe(). This is often because
usbhs_mod_probe lacks a __devinit annotation or the annotation of
usbhs_mod_host_probe is wrong.
WARNING: drivers/usb/renesas_usbhs/renesas_usbhs.o(.text+0xfd7): Section
mismatch in reference from the function usbhs_mod_probe() to the function
.devexit.text:usbhs_mod_host_remove() The function usbhs_mod_probe() references
a function in an exit section. Often the function usbhs_mod_host_remove() has
valid usage outside the exit section and the fix is to remove the __devexit
annotation of usbhs_mod_host_remove.
WARNING: drivers/usb/renesas_usbhs/renesas_usbhs.o(.text+0x1005): Section
mismatch in reference from the function usbhs_mod_remove() to the function
.devexit.text:usbhs_mod_host_remove() The function usbhs_mod_remove()
references a function in an exit section. Often the function
usbhs_mod_host_remove() has valid usage outside the exit section and the fix is
to remove the __devexit annotation of usbhs_mod_host_remove.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since renesas_usbhs mod_host didn't use
struct completion as static object, the warning of lockdep came out.
This patch fixup this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix compile error in file drivers/usb/gadget/fsl_udc_core.c.
drivers/usb/gadget/fsl_udc_core.c: In function 'portscx_device_speed':
drivers/usb/gadget/fsl_udc_core.c:1720: error: 'speed' undeclared (first
use in this function)
Introduced in commit e538dfdae8
(usb: Provide usb_speed_string() function)
Signed-off-by: Alexander Aring <a.aring@phytec.de>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "BCLR" in CFIFOCTR/DnFIFOCTR can flush the fifo of "CPU side" only.
To flush the fifo of "SIE side", we have to use the "ACLRM" in PIPEnCTR.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The udc-newstyle needs device_register in probe() of platform_device.
If it doesn't call, kernel panic happens in the sysfs_create_dir() when
we run modprobe a gadget driver.
[ balbi@ti.com : fix compile warning introduced by this patch ]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Those are simply giving information about the current
state of the UDC, nothing really fancy. We can let
everybody read those.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_gadget_disconnect() is responsible of removing
data pullups. Before doing that we must, first, tell
gadget driver we're disconnecting (by calling disconnect
method on gadget driver structure), unbind the gadget
driver and stop the controller.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
that has already being done by udc-core.c. It's
unnecessary and might cause issues with some gadget
drivers.
Tested: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should not be using dev_get_drvdata() because we
never call dev_set_drvdata(). Let's use container_of()
as all other sysfs attributes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-linus' of ra.kernel.org:/pub/scm/linux/kernel/git/sarah/xhci:
usb, xhci: Clear warm reset change event during init
xhci: Set slot and ep0 flags for address command.
usb, xhci: fix lockdep warning on endpoint timeout
.. with new name. Because nothing says "really solid kernel release"
like naming it after an extinct animal that just happened to be in the
news lately.
Mountpoint crossing is similar to following procfs symlinks - we do
not get ->d_revalidate() called for dentry we have arrived at, with
unpleasant consequences for NFS4.
Simple way to reproduce the problem in mainline:
cat >/tmp/a.c <<'EOF'
#include <unistd.h>
#include <fcntl.h>
#include <stdio.h>
main()
{
struct flock fl = {.l_type = F_RDLCK, .l_whence = SEEK_SET, .l_len = 1};
if (fcntl(0, F_SETLK, &fl))
perror("setlk");
}
EOF
cc /tmp/a.c -o /tmp/test
then on nfs4:
mount --bind file1 file2
/tmp/test < file1 # ok
/tmp/test < file2 # spews "setlk: No locks available"...
What happens is the missing call of ->d_revalidate() after mountpoint
crossing and that's where NFS4 would issue OPEN request to server.
The fix is simple - treat mountpoint crossing the same way we deal with
following procfs-style symlinks. I.e. set LOOKUP_JUMPED...
Cc: stable@kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf top: Fix live annotation in the --stdio interface
perf top tui: Don't recalc column widths considering just the first page
perf report: Add progress bar when processing time ordered events
perf hists browser: Warn about lost events
perf tools: Fix a typo of command name as trace-cmd
perf hists: Fix recalculation of total_period when sorting entries
perf header: Fix build on old systems
perf ui browser: Handle K_RESIZE in dialog windows
perf ui browser: No need to switch char sets that often
perf hists browser: Use K_TIMER
perf ui: Rename ui__warning_paranoid to ui__error_paranoid
perf ui: Reimplement the popup windows using libslang
perf ui: Reimplement ui__popup_menu using ui__browser
perf ui: Reimplement ui_helpline using libslang
perf ui: Improve handling sigwinch a bit
perf ui progress: Reimplement using slang
perf evlist: Fix grouping of multiple events
Commit 32aaeffbd4 (Merge branch
'modsplit-Oct31_2011'...) caused some build errors. Fix these
and make sure we always have export.h or module.h included
for MODULE_ and EXPORT_SYMBOL users:
$ grep -rl ^MODULE_ arch/arm/*omap*/*.c | xargs \
grep -L linux/module.h
arch/arm/mach-omap2/dsp.c
arch/arm/mach-omap2/mailbox.c
arch/arm/mach-omap2/omap-iommu.c
arch/arm/mach-omap2/smartreflex.c
Also check we either have export.h or module.h included
for the files exporting symbols:
$ grep -rl EXPORT_SYMBOL arch/arm/*omap*/*.c | xargs \
grep -L linux/export.h | xargs grep -L linux/module.h
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include linux/export.h to fix below build warning:
CC arch/arm/plat-omap/omap_device.o
arch/arm/plat-omap/omap_device.c:1055: warning: data definition has no type or storage class
arch/arm/plat-omap/omap_device.c:1055: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/arm/plat-omap/omap_device.c:1055: warning: parameter names (without types) in function declaration
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
forcedeth: fix a few sparse warnings (variable shadowing)
forcedeth: Improve stats counters
forcedeth: remove unneeded stats updates
forcedeth: Acknowledge only interrupts that are being processed
forcedeth: fix race when unloading module
MAINTAINERS/rds: update maintainer
wanrouter: Remove kernel_lock annotations
usbnet: fix oops in usbnet_start_xmit
ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined
etherh: Add MAINTAINERS entry for etherh
bonding: comparing a u8 with -1 is always false
sky2: fix regression on Yukon Optima
netlink: clarify attribute length check documentation
netlink: validate NLA_MSECS length
i825xx:xscale:8390:freescale: Fix Kconfig dependancies
macvlan: receive multicast with local address
tg3: Update version to 3.121
tg3: Eliminate timer race with reset_task
tg3: Schedule at most one tg3_reset_task run
tg3: Obtain PCI function number from device
...
This fixes the following sparse warnings:
drivers/net/ethernet/nvidia/forcedeth.c:2113:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2155:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2227:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2271:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2986:20: warning: symbol 'addr' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2963:6: originally declared here
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx byte count was off; instead use the hardware's count. Tx packet
count was counting pre-TSO packets; instead count on-the-wire packets.
Report hardware dropped frame count as rx_fifo_errors.
- The count of transmitted packets reported by the forcedeth driver
reports pre-TSO (TCP Segmentation Offload) packet counts and not the
count of the number of packets sent on the wire. This change fixes
the forcedeth driver to report the correct count. Fixed the code by
copying the count stored in the NIC H/W to the value reported by the
driver.
- Count rx_drop_frame errors as rx_fifo_errors:
We see a lot of rx_drop_frame errors if we disable the rx bottom-halves
for too long. Normally, rx_fifo_errors would be counted in this case.
The rx_drop_frame error count is private to forcedeth and is not
reported by ifconfig or sysfs. The rx_fifo_errors count is currently
unused in the forcedeth driver. It is reported by ifconfig as overruns.
This change reports rx_drop_frame errors as rx_fifo_errors.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wangyanqing
Tomoya MORINAGA
Alan Stern
sordna
Shaohui Xie
Jean-Christophe PLAGNIOL-VILLARD
Havard Skinnemoen
Josh Boyer
Thomas Poussevin
Bart Hartgers
Felipe Balbi
Sebastian Andrzej Siewior
Kuninori Morimoto
Marc Kleine-Budde
Michael Grzeschik
Daniel Mack
Paul Zimmerman
Alexander Aring
Yoshihiro Shimoda
Luciano Coelho
Mian Yousaf Kaukab
Greg Kroah-Hartman
Linus Torvalds
Al Viro
Tony Lindgren
Axel Lin
david decotigny
Mandeep Baines