The encoder variable can be NULL in this function so I believe it should
be checked before dereference.
Coverity CID: 13253
[airlied: extremely unlikely to happen]
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Stanse found a memory leak in radeon_master_create. master_priv is not
freed/assigned on all paths. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_pci_alloc() has input of address mask for setting pci dma
mask on the device, which should be properly setup by drm driver.
And leave it as a param for drm_pci_alloc() would cause confusion
or mistake would corrupt the correct dma mask setting, as seen on
intel hw which set wrong dma mask for hw status page. So remove
it from drm_pci_alloc() function.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is a possibility of a loop happening in the PLL output clock
chain on the S3C64XX series. clk_mpll's parent was set to be
clk_mout_mpll, but this is fed from clk_fout_epll (which is also
clk_mpll).
clk_mpll is meant to be the output from the MPLL, and clk_mout_mpll
is a seperate clock derived from the mux of clk_mpll and clk_fin_mpll
and thus should be considered a seperate clock.
Anything using clk_mpll directly really should not be relying on this
being the clock that is eventually routed to a peripheral, so remove the
loop and ensure that the clocks accurately represent the clock chain
in the device.
The clk_mpll is not being used outside of the s3c6400-clock.c code, so
this change should not break anything else.
Do the same for the EPLL.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (23 commits)
drm/i915: remove full registers dump debug
drm/i915: Add DP dpll limit on ironlake and use existing DPLL search function
drm/i915: Select the correct BPC for LVDS on Ironlake
drm/i915: Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake
drm/i915: Enable/disable the dithering for LVDS based on VBT setting
drm/i915: Permit pinning whilst the device is 'suspended'
drm/i915: Hold struct mutex whilst pinning power context bo.
drm/i915: fix unused var
drm/i915: Storage class should be before const qualifier
drm/i915: remove render reclock support
drm/i915: Fix RC6 suspend/resume
drm/i915: execbuf2 support
drm/i915: Reload hangcheck timer too for Ironlake
drm/i915: only enable hotplug for detected outputs
drm/i915: Track whether cursor needs physical address in intel_device_info
drm/i915: Implement IS_* macros using static tables
drm/i915: Move PCI IDs into i915 driver
drm/i915: Update LVDS connector status when receiving ACPI LID event
drm/i915: Add MALATA PC-81005 to ACPI LID quirk list
drm/i915: implement new pm ops for i915
...
The MMU code uses the copy_*_user_page() variants in access_process_vm()
rather than copy_*_user() as the former includes an icache flush. This
is important when doing things like setting software breakpoints with
gdb. So switch the NOMMU code over to do the same.
This patch makes the reasonable assumption that copy_from_user_page()
won't fail - which is probably fine, as we've checked the VMA from which
we're copying is usable, and the copy is not allowed to cross VMAs. The
one case where it might go wrong is if the VMA is a device rather than
RAM, and that device returns an error which - in which case rubbish will
be returned rather than EIO.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: David McCullough <david_mccullough@mcafee.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When working with FDPIC, there are many shared mappings of read-only
code regions between applications (the C library, applet packages like
busybox, etc.), but the current do_mmap_pgoff() function will issue an
icache flush whenever a VMA is added to an MM instead of only doing it
when the map is initially created.
The flush can instead be done when a region is first mmapped PROT_EXEC.
Note that we may not rely on the first mapping of a region being
executable - it's possible for it to be PROT_READ only, so we have to
remember whether we've flushed the region or not, and then flush the
entire region when a bit of it is made executable.
However, this also affects the brk area. That will no longer be
executable. We can mprotect() it to PROT_EXEC on MPU-mode kernels, but
for NOMMU mode kernels, when it increases the brk allocation, making
sys_brk() flush the extra from the icache should suffice. The brk area
probably isn't used by NOMMU programs since the brk area can only use up
the leavings from the stack allocation, where the stack allocation is
larger than requested.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current code will load the stack size and protection markings, but
then only use the markings in the MMU code path. The NOMMU code path
always passes PROT_EXEC to the mmap() call. While this doesn't matter
to most people whilst the code is running, it will cause a pointless
icache flush when starting every FDPIC application. Typically this
icache flush will be of a region on the order of 128KB in size, or may
be the entire icache, depending on the facilities available on the CPU.
In the case where the arch default behaviour seems to be desired
(EXSTACK_DEFAULT), we probe VM_STACK_FLAGS for VM_EXEC to determine
whether we should be setting PROT_EXEC or not.
For arches that support an MPU (Memory Protection Unit - an MMU without
the virtual mapping capability), setting PROT_EXEC or not will make an
important difference.
It should be noted that this change also affects the executability of
the brk region, since ELF-FDPIC has that share with the stack. However,
this is probably irrelevant as NOMMU programs aren't likely to use the
brk region, preferring instead allocation via mmap().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.33' of git://linux-nfs.org/~bfields/linux:
sunrpc: fix peername failed on closed listener
nfsd: make sure data is on disk before calling ->fsync
nfsd: fix "insecure" export option
Make sure compiler won't do weird things with limits. E.g. fetching
them twice may return 2 different values after writable limits are
implemented.
I.e. either use rlimit helpers added in
3e10e716ab
or ACCESS_ONCE if not applicable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Recent change is missing to update "rehash". With that change, it will
become the cause of adding dentry to hash twice.
This explains the reason of Oops (dereference the freed dentry in
__d_lookup()) on my machine.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Reported-by: Marvin <marvin24@gmx.de>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
pcibus_to_node can return -1 if we cannot determine which node a pci bus
is on. If passed -1, cpumask_of_node will negatively index the lookup array
and pull in random data:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
00000000,00000003,00000000,00000000
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
64-65
Change cpumask_of_node to check for -1 and return cpu_all_mask in this
case:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
ffffffff,ffffffff,ffffffff,ffffffff
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
0-127
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There're some warnings of "nfsd: peername failed (err 107)!"
socket error -107 means Transport endpoint is not connected.
This warning message was outputed by svc_tcp_accept() [net/sunrpc/svcsock.c],
when kernel_getpeername returns -107. This means socket might be CLOSED.
And svc_tcp_accept was called by svc_recv() [net/sunrpc/svc_xprt.c]
if (test_bit(XPT_LISTENER, &xprt->xpt_flags)) {
<snip>
newxpt = xprt->xpt_ops->xpo_accept(xprt);
<snip>
So this might happen when xprt->xpt_flags has both XPT_LISTENER and XPT_CLOSE.
Let's take a look at commit b0401d72, this commit has moved the close
processing after do recvfrom method, but this commit also introduces this
warnings, if the xpt_flags has both XPT_LISTENER and XPT_CLOSED, we should
close it, not accpet then close.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Cc: J. Bruce Fields <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
nfsd is not using vfs_fsync, so I missed it when changing the calling
convention during the 2.6.32 window. This patch fixes it to not only
start the data writeout, but also wait for it to complete before calling
into ->fsync.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Fix auth_gss printk format warning:
net/sunrpc/auth_gss/auth_gss.c:660: warning: format '%ld' expects type 'long int', but argument 3 has type 'ssize_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Correct misspelled "CONFIG_IPv6" that was introduced in commit
d14714df ("IB/addr: Fix IPv6 routing lookup"). The config variable
should be all uppercase.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
[ This was my fault when I munged the original patch. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If mlx4_init_port_info() fails, cleanup the initialized ports only.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In mlx4_ib_post_recv(), we should check the queue for overflow using
recv_cq instead of send_cq (current code looks like a copy-and-paste
mistake).
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
As for memfree mthca hardware, ConnectX also requires SRQ WQE scatter
entries to be initialized with the invalid L_Key at SRQ creation time.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With the recent irq migration fixes (post 2.6.32), Gary Hade has noticed
"No IRQ handler for vector" messages during the 2.6.33-rc1 kernel boot on IBM
AMD platforms and root caused the issue to this commit:
> commit 23359a88e7
> Author: Suresh Siddha <suresh.b.siddha@intel.com>
> Date: Mon Oct 26 14:24:33 2009 -0800
>
> x86: Remove move_cleanup_count from irq_cfg
As part of this patch, we have removed the move_cleanup_count check
in smp_irq_move_cleanup_interrupt(). With this change, we can run into a
situation where an irq cleanup interrupt on a cpu can cleanup the vector
mappings associated with multiple irqs, of which one of the irq's migration
might be still in progress. As such when that irq hits the old cpu, we get
the "No IRQ handler" messages.
Fix this by checking for the irq_cfg's move_in_progress and if the move
is still in progress delay the vector cleanup to another irq cleanup
interrupt request (which will happen when the irq starts arriving at the
new cpu destination).
Reported-and-tested-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1262804191.2732.7.camel@sbs-t61.sc.intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'davinci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci:
DaVinci: DM365: Add the device_enable for the DaVinci Keyscan
davinci: enable ARCH_HAS_HOLES_MEMORYMODEL for DaVinci
davinci: da8xx/omap-l1: mark RTC as a wakeup source
davinci: cp_intc: provide set_wake function
Davinci VPFE Capture: Take i2c adapter id through platform data
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] lpfc 8.3.7: Update Driver version to 8.3.7
[SCSI] lpfc 8.3.7: Fix discovery failures.
[SCSI] lpfc 8.3.7: Fix SCSI protocol related errors.
[SCSI] lpfc 8.3.7: Fix hardware/SLI relates issues
[SCSI] lpfc 8.3.7: Fix NPIV operation errors
[SCSI] lpfc 8.3.7: Fix FC protocol errors
[SCSI] stex: fix scan of nonexistent lun
[SCSI] pmcraid: fix to avoid twice scsi_dma_unmap for a command
[SCSI] qla2xxx: Update version number to 8.03.01-k9.
[SCSI] qla2xxx: Added to EEH support.
[SCSI] qla2xxx: Extend base EEH support in qla2xxx.
[SCSI] qla2xxx: Fix for a multiqueue bug in CPU affinity mode
[SCSI] qla2xxx: Get the link data rate explicitly during device resync.
[SCSI] cxgb3i: Fix a login over vlan issue
This one reverts 9e3a6d155e.
As reported by http://bugzilla.kernel.org/show_bug.cgi?id=14485,
this dump will cause hang problem on some machine. If something
really needs this kind of full registers dump, that could be done
within intel-gpu-tools.
Cc: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For some clocks, the old Ironlake DPLL calculator wold give m/n/p
combinations that didn't match the spreadsheet of what HW validation
tests. Instead, use the G4X DPLL calculator, which does a better job
at it.
So we use the intel_g4x_find_best_pll to calculate the DPLL for CRT/HDMI/LVDS
on ironlake. At the same time to consider the dpll setting for display port, we
add the display port DPLL limit on ironlake, which will directly use the
function of intel_find_pll_ironlake_dp to get the corresponding dpll setting.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Select the correct BPC for LVDS on Ironlake. If it is 18-bit LVDS panel,
the BPC will be 6. When it is 24-bit LVDS panel, the BPC will 8.
At the same time the BPC will be 8 when the output device is CRT/HDMI/DP.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Enable/disable the dithering for LVDS based on VBT setting. On the 965/g4x
platform the dithering flag is defined in LVDS register. And on the ironlake
the dithering flag is defined in pipeconf register.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As pinning (allocating and binding GTT memory) does not actually invoke
GPU commands, it is safe, and indeed is attempted, during resumption
from suspension:
[drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Hugh found an error path where we were attempting to unref a bo without
holding the struct mutex:
[drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16
------------[ cut here ]------------
WARNING: at drivers/gpu/drm/drm_gem.c:438 drm_gem_object_free+0x20/0x5e()
Hardware name: ESPRIMO Mobile V5505
Modules linked in: snd_pcm_oss snd_mixer_oss snd_seq snd_seq_device
Pid: 3793, comm: s2ram Not tainted 2.6.33-rc2 #4
Call Trace:
[<7815298e>] warn_slowpath_common+0x59/0x6b
[<781529b3>] warn_slowpath_null+0x13/0x18
[<78317c1a>] ? drm_gem_object_free+0x20/0x5e
[<78317c1a>] drm_gem_object_free+0x20/0x5e
[<78317bfa>] ? drm_gem_object_free+0x0/0x5e
[<7829df11>] kref_put+0x38/0x45
[<7833a5f0>] intel_init_clock_gating+0x232/0x271
[<78317bfa>] ? drm_gem_object_free+0x0/0x5e
[<7832c307>] i915_restore_state+0x21a/0x2b3
[<7832379d>] i915_resume+0x3c/0xbb
[<78174fe5>] ? trace_hardirqs_on_caller+0xfc/0x123
[<7831c756>] ? drm_class_resume+0x0/0x3e
[<7831c78d>] drm_class_resume+0x37/0x3e
[<78351e0a>] legacy_resume+0x1e/0x51
[<78351ece>] device_resume+0x91/0xab
[<7831c756>] ? drm_class_resume+0x0/0x3e
[<78352226>] dpm_resume+0x58/0x10f
[<783522fb>] dpm_resume_end+0x1e/0x2c
[<78180f80>] suspend_devices_and_enter+0x61/0x84
[<78180ff8>] enter_state+0x55/0x83
[<7818091c>] state_store+0x94/0xaa
[<7829d09e>] kobj_attr_store+0x1e/0x23
[<782098e0>] sysfs_write_file+0x66/0x99
[<781cd2f0>] vfs_write+0x8a/0x108
[<781cd408>] sys_write+0x3c/0x63
[<78125c10>] sysenter_do_call+0x12/0x36
---[ end trace a343537f29950fda ]---
It is in fact slightly more insiduous that first appears since we are
attempting to not just free the object without the lock, but are trying
to do the whole bo manipulation without holding the lock.
Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
drivers/gpu/drm/i915/i915_dma.c: In function 'i915_driver_load':
drivers/gpu/drm/i915/i915_dma.c:1114: warning: 'll_base' may be used uninitialized in this function
Partly this is because gcc isn't smart enough. But `ll_base' does get used
uninitialised in the DRM_DEBUG() call.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
This code generally fails to adjust the render clock, and when it does,
it conflicts with some other register settings and can cause problems.
So remove this code altogether. I'm reworking it now to do the right
thing, but the only bit it will share is the VBT check for whether
reclocking is supported, so I'm leaving that bit.
Reverts most of 652c393a33 ("add dynamic
clock frequency control"), though for many the regressions showed up
in the later 181a5336d6 ("Fix render
reclock availability detection").
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We restored RC6 twice on resume, even with modesetting off. Instead,
only restore it once and skip RC6 initialization entirely in non-KMS mode.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch adds a new execbuf ioctl, execbuf2, for use by clients that
want to control fence register allocation more finely. The buffer
passed in to the new ioctl includes a new relocation type to indicate
whether a given object needs a fence register assigned for the command
buffer in question.
Compatibility with the existing execbuf ioctl is implemented in terms
of the new code, preserving the assumption that fence registers are
required for pre-965 rendering commands.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: Remove pre-emptive clear_fence_reg()]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
[anholt: Removed dmesg spam]
Signed-off-by: Eric Anholt <eric@anholt.net>
Adds the device_enable function to the DaVinci Keyscan platform data
to setup the PINMUX configuration.
It also removes #ifdef from the DM365 EVM board in order to load it
properly as a module.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
All DaVinci platforms include a DSP or co-processor for
audio/video acceleration.
While creating memory for the DSP/co-processor, system
integrator can end up creating a hole in the memory map
of the sort:
<kernel memory> <hole (memory for DSP)> <kernel memory>
This sort of configuration needs ARCH_HAS_HOLES_MEMORYMODEL
enabled. See further details see this discussion on ARM
linux mailing list:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg15262.html
The patch is boot tested on OMAP-L138, DM6446 and DM355 EVMs
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Sriramakrishnan <srk@ti.com>
CC: Khasim Syed Mohammed <khasim@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On da850, RTC alarm is a wakeup source from deep sleep.
Mark it as a wakeup source after the rtc platform device
is registered.
Without this patch, the rtc-omap driver suspends the RTC
during the suspend sequence and hence it cannot wakeup the
SoC.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There is nothing special to be done for interrupts
which can wakeup the device from sleep on CP-INTC,
but not having a set_wake implemented prevents use
of common drivers which expect this function to be
implemented for all wakeup interrupt sources.
This patch fixes the issue encountered when using the
omap-rtc driver on DA850. On DA850 the RTC alarm
interrupt is used to wake up the SoC from deep sleep
mode. Without this patch, the disable_irq_wake throws
an unbalanced wake disable warning while resuming
because the previous enable call fails for lack of
set_wake implementation.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The I2C adapter ID is actually depends on Board and may vary, Davinci
uses id=1, but in case of AM3517 id=3.
So modified respective davinci board files.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
exofs: simple_write_end does not mark_inode_dirty
exofs: fix pnfs_osd re-definitions in pre-pnfs trees
* master.kernel.org:/home/rmk/linux-2.6-arm: (22 commits)
ARM: 5865/1: nuc900 ethernet driver needs mii
ARM: 5864/1: Implement arch_reset() in NUC900
ARM: 5863/1: fix bugs of clock source of NUC900
ARM: 5858/1: Remove unused vma_vm_flags macro from v7wbi_flush_user_tlb_range
imx/mx3: depend on USB_ULPI for otg_ulpi_create
ARM: MX3: make CPU revision number detection work on all boards
mx25: pdk: add platform code for FEC support
mx25: add support for FEC on i.MX25
mx25: s/NO_PAD_CTL/NO_PAD_CTRL/
mx31moboard: fix usbh device names
mx3: add support for the mt9v022 camera sensor to pcm037 platform
mx27: mxt_td60: Remove not used UART pins
[ARM] pxa/poodle: fix incorrect 'gpio_card_detect' of MMC
[ARM] pxa/zylonite: simplify reduntant gpio settings on mmc slot
[ARM] pxa/ttc_dkb: remove duplicate macro definition
[ARM] pxa/zeus: provide power-source information when APM is enabled
[ARM] pxa/zeus: relax memory timings on Zeus ethernet ports
[ARM] pxa/zeus: make internal zeus_get_pcb_info static
[ARM] pxa/littleton: select CPU_PXA300 and CPU_PXA310
[ARM] pxa/littleton: add UART3 GPIO config
...
Commit 35dead4 "modules: don't export section names of empty sections
via sysfs" changed the set of sections that have attributes, but did
not change the iteration over these attributes in add_notes_attrs().
This can lead to add_notes_attrs() creating attributes with the wrong
names or with null name pointers.
Introduce a sect_empty() function and use it in both add_sect_attrs()
and add_notes_attrs().
Reported-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Cc: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Look up primary dac adj values from the table if
there is no bios or bios dac table to reference.
The lookup table may need to be adjusted for certain
families.
Should fix kernel bug 14945.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Darren Jenkins
Jiri Slaby
Dave Airlie
Roel Kluin
Adam Jackson
Zhenyu Wang
Ben Dooks
Linus Torvalds
Jie Zhang
Mike Frysinger
Mike Frysinger
Tony Luck
OGAWA Hirofumi
Anton Blanchard
Xiaotian Feng
Christoph Hellwig
Randy Dunlap
Roland Dreier
Robert P. J. Day
Eli Cohen
Or Gerlitz
Jack Morgenstein
Suresh Siddha
Zhenyu Wang
Zhao Yakui
Chris Wilson
Andrew Morton
Tobias Klauser
Jesse Barnes
Andrew Lutomirski
Miguel Aguilar
Sekhar Nori
Vaibhav Hiremath
Ben Hutchings
Alex Deucher