The original MPIC MSI bank contains 8 registers, MPIC v4.3 MSI bank
contains 16 registers, and this patch adds NR_MSI_REG_MAX and
NR_MSI_IRQS_MAX to describe the maximum capability of MSI bank.
MPIC v4.3 provides MSIIR1 to index these 16 MSI registers. MSIIR1
uses different bits definition than MSIIR. This patch adds
ibs_shift and srs_shift to indicate the bits definition of the
MSIIR and MSIIR1, so the same code can handle the MSIIR and MSIIR1
simultaneously.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
[scottwood@freescale.com: reinstated static on all_avail]
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch drops the powerpc-specific irq_host structures and uses the common
irq_domain strucutres defined in linux/irqdomain.h. It also fixes all
the users to use the new structure names.
Renaming irq_host to irq_domain has been discussed for a long time, and this
patch is a step in the process of generalizing the powerpc virq code to be
usable by all architecture.
An astute reader will notice that this patch actually removes the irq_host
structure instead of renaming it. This is because the irq_domain structure
already exists in include/linux/irqdomain.h and has the needed data members.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Add support for vmpic-msi nodes to the fsl_msi driver. The MSI is
virtualized by the hypervisor, so the vmpic-msi does not contain a 'reg'
property. Instead, the driver uses hcalls.
Add support for the "msi-address-64" property to the fsl_pci driver.
The Freescale hypervisor typically puts the virtualized MSIIR register
in the page after the end of DDR, so we extend the DDR ATMU to cover it.
Any other location for MSIIR is not supported, for now.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On Freescale parts with multiple MSI controllers, the controllers are
combined into one "pool" of interrupts. Whenever a device requests an MSI
interrupt, the next available interrupt from the pool is selected,
regardless of which MSI controller the interrupt is from. This works
because each PCI bus has an ATMU to all of CCSR, so any PCI device can
access any MSI interrupt register.
The fsl,msi property is used to specify that a given PCI bus should only
use a specific MSI device. This is necessary, for example, with the
Freescale hypervisor, because the MSI devices are assigned to specific
partitions.
Ideally, we'd like to be able to assign MSI devices to PCI busses within
the MSI or PCI layers. However, there does not appear to be a mechanism
to do that. Whenever the MSI layer wants to allocate an MSI interrupt to
a PCI device, it just calls arch_setup_msi_irqs(). It would be nice if we
could register an MSI device with a specific PCI bus.
So instead we remember the phandles of each MSI device, and we use that to
limit our search for an available interrupt. Whenever we are asked to
allocate a new interrupt for a PCI device, we check the fsl,msi property
of the PCI bus for that device. If it exists, then as we are looping over
all MSI devices, we skip the ones that don't have a matching phandle.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the msi-address-64 property of a PCI node. This property
specifies the PCI address of MSIIR (message signaled interrupt index
register).
In commit 3da34aae ("powerpc/fsl: Support unique MSI addresses per PCIe Root
Complex"), the msi_addr_hi/msi_addr_lo fields of struct fsl_msi were redefined
from an actual address to just an offset, but the fields were not renamed
accordingly. These fields are replace with a single field, msiir_offset,
to reflect the new meaning.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Put all fsl_msi banks in a linked list. The list of banks then can be
traversed when allocating new msi interrupts. Also fix failing path
of fsl_setup_msi_irqs().
Signed-off-by: Zhao Chenhui <b26998@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is 90% straight forward, although we have to change a few
printk format strings as well because of the change in type of hwirq.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The FSL MSI code keeps a pointer to the of_node from the device
it represents. However it also has an irq_host, which contains
a pointer to the of_node, so use that one instead.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This MSI driver can be used on 83xx/85xx/86xx board.
In this driver, virtual interrupt host and chip were
setup. There are 256 MSI interrupts in this host, Every 32
MSI interrupts cascaded to one IPIC/MPIC interrupt.
The chip was treated as edge sensitive and some necessary
functions were setup for this chip.
Before using the MSI interrupt, PCI/PCIE device need to
ask for a MSI interrupt in the 256 MSI interrupts. A 256bit
bitmap show which MSI interrupt was used, reserve bit in
the bitmap can be used to force the device use some designate
MSI interrupt in the 256 MSI interrupts. Sometimes this is useful
for testing the all the MSI interrupts. The msi-available-ranges
property in the dts file was used for this purpose.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Minghuan Lian
Grant Likely
Timur Tabi
Li Yang
Michael Ellerman
Jason Jin