If the available hardware exceeds DMAR_UNITS_SUPPORTED (previously set
to MAX_IO_APICS, or 128), it causes these messages: "DMAR: Failed to
allocate seq_id", "DMAR: Parse DMAR table failure.", and "x2apic: IRQ
remapping doesn't support X2APIC mode x2apic disabled"; and the system
fails to boot properly.
To support up to 64 sockets with 10 DMAR units each (640), make the
value of DMAR_UNITS_SUPPORTED default 1024.
Signed-off-by: Steve Wahl<steve.wahl@hpe.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Link: https://lore.kernel.org/linux-iommu/20220615183650.32075-1-steve.wahl@hpe.com/
Link: https://lore.kernel.org/r/20220702015610.2849494-7-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The IOMMU table tries to separate the different IOMMUs into different
backends, but actually requires various cross calls.
Rewrite the code to do the generic swiotlb/swiotlb-xen setup directly
in pci-dma.c and then just call into the IOMMU drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
When the dmar translation fault happens, the kernel prints a single line
fault reason with corresponding hexadecimal code defined in the Intel VT-d
specification.
Currently, when user wants to debug the translation fault in detail,
debugfs is used for dumping the dmar_translation_struct, which is not
available when the kernel failed to boot.
Dump the DMAR translation structure, pagewalk the IO page table and print
the page table entry when the fault happens.
This takes effect only when CONFIG_DMAR_DEBUG is enabled.
Signed-off-by: Kyung Min Park <kyung.min.park@intel.com>
Link: https://lore.kernel.org/r/20210815203845.31287-1-kyung.min.park@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The VT-d spec requires (10.4.4 Global Command Register, TE field) that:
Hardware implementations supporting DMA draining must drain any in-flight
DMA read/write requests queued within the Root-Complex before completing
the translation enable command and reflecting the status of the command
through the TES field in the Global Status register.
Unfortunately, some integrated graphic devices fail to do so after some
kind of power state transition. As the result, the system might stuck in
iommu_disable_translation(), waiting for the completion of TE transition.
This provides a quirk list for those devices and skips TE disabling if
the qurik hits.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=208363
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=206571
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Koba Ko <koba.ko@canonical.com>
Tested-by: Jun Miao <jun.miao@windriver.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200723013437.2268-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Similar to the commit 02d715b4a8 ("iommu/vt-d: Fix RCU list debugging
warnings"), there are several other places that call
list_for_each_entry_rcu() outside of an RCU read side critical section
but with dmar_global_lock held. Silence those false positives as well.
drivers/iommu/intel-iommu.c:4288 RCU-list traversed in non-reader section!!
1 lock held by swapper/0/1:
#0: ffffffff935892c8 (dmar_global_lock){+.+.}, at: intel_iommu_init+0x1ad/0xb97
drivers/iommu/dmar.c:366 RCU-list traversed in non-reader section!!
1 lock held by swapper/0/1:
#0: ffffffff935892c8 (dmar_global_lock){+.+.}, at: intel_iommu_init+0x125/0xb97
drivers/iommu/intel-iommu.c:5057 RCU-list traversed in non-reader section!!
1 lock held by swapper/0/1:
#0: ffffffffa71892c8 (dmar_global_lock){++++}, at: intel_iommu_init+0x61a/0xb13
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The intel-iommu driver assumes that the iommu state is
cleaned up at the start of the new kernel.
But, when we try to kexec boot something other than the
Linux kernel, the cleanup cannot be relied upon.
Hence, cleanup before we go down for reboot.
Keeping the cleanup at initialization also, in case BIOS
leaves the IOMMU enabled.
I considered turning off iommu only during kexec reboot, but a clean
shutdown seems always a good idea. But if someone wants to make it
conditional, such as VMM live update, we can do that. There doesn't
seem to be such a condition at this time.
Tested that before, the info message
'DMAR: Translation was enabled for <iommu> but we are not in kdump mode'
would be reported for each iommu. The message will not appear when the
DMA-remapping is not enabled on entry to the kernel.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
There are a few macros in IOMMU have single-char identifiers make the code
hard to read and debug. Replace them with meaningful names.
Link: http://lkml.kernel.org/r/1559566783-13627-1-git-send-email-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 33 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000435.254582722@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel VT-d spec added a new DMA_CTRL_PLATFORM_OPT_IN_FLAG flag in DMAR
ACPI table [1] for BIOS to report compliance about platform initiated
DMA restricted to RMRR ranges when transferring control to the OS. This
means that during OS boot, before it enables IOMMU none of the connected
devices can bypass DMA protection for instance by overwriting the data
structures used by the IOMMU. The OS also treats this as a hint that the
IOMMU should be enabled to prevent DMA attacks from possible malicious
devices.
A use of this flag is Kernel DMA protection for Thunderbolt [2] which in
practice means that IOMMU should be enabled for PCIe devices connected
to the Thunderbolt ports. With IOMMU enabled for these devices, all DMA
operations are limited in the range reserved for it, thus the DMA
attacks are prevented. All these devices are enumerated in the PCI/PCIe
module and marked with an untrusted flag.
This forces IOMMU to be enabled if DMA_CTRL_PLATFORM_OPT_IN_FLAG is set
in DMAR ACPI table and there are PCIe devices marked as untrusted in the
system. This can be turned off by adding "intel_iommu=off" in the kernel
command line, if any problems are found.
[1] https://software.intel.com/sites/default/files/managed/c5/15/vt-directed-io-spec.pdf
[2] https://docs.microsoft.com/en-us/windows/security/information-protection/kernel-dma-protection-for-thunderbolt
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Sohil Mehta <sohil.mehta@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
The enum is currently defined in Intel-specific DMAR header file,
but it is also used by APIC common code. Therefore, move it to
a more appropriate interrupt-remapping common header file.
This will also be used by subsequent patches.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The notifier function will take the dmar_global_lock too, so
lockdep complains about inverse locking order when the
notifier is registered under the dmar_global_lock.
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Fixes: 59ce0515cd ('iommu/vt-d: Update DRHD/RMRR/ATSR device scope caches when PCI hotplug happens')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
We don't actually need the full rculist.h header in sched.h anymore,
we will be able to include the smaller rcupdate.h header instead.
But first update code that relied on the implicit header inclusion.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The IRTE (Interrupt Remapping Table Entry) is either an entry for
remapped or for posted interrupts. The hardware distiguishes between
remapped and posted entries by bit 15 in the low 64 bit of the
IRTE. If cleared the entry is remapped, if set it's posted.
The entries have common fields and dependent on the posted bit fields
with different meanings.
Extend struct irte to handle the differences between remap and posted
mode by having three structs in the unions:
- Shared
- Remapped
- Posted
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Feng Wu <feng.wu@intel.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Cc: jiang.liu@linux.intel.com
Cc: iommu@lists.linux-foundation.org
Cc: dwmw2@infradead.org
Link: http://lkml.kernel.org/r/1433827237-3382-3-git-send-email-feng.wu@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Refine the interfaces to create IRQ for DMAR unit. It's a preparation
for converting DMAR IRQ to hierarchical irqdomain on x86.
It also moves dmar_alloc_hwirq()/dmar_free_hwirq() from irq_remapping.h
to dmar.h. They are not irq_remapping specific.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: iommu@lists.linux-foundation.org
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Link: http://lkml.kernel.org/r/1428905519-23704-20-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On Intel platforms, an IO Hub (PCI/PCIe host bridge) may contain DMAR
units, so we need to support DMAR hotplug when supporting PCI host
bridge hotplug on Intel platforms.
According to Section 8.8 "Remapping Hardware Unit Hot Plug" in "Intel
Virtualization Technology for Directed IO Architecture Specification
Rev 2.2", ACPI BIOS should implement ACPI _DSM method under the ACPI
object for the PCI host bridge to support DMAR hotplug.
This patch introduces interfaces to parse ACPI _DSM method for
DMAR unit hotplug. It also implements state machines for DMAR unit
hot-addition and hot-removal.
The PCI host bridge hotplug driver should call dmar_hotplug_hotplug()
before scanning PCI devices connected for hot-addition and after
destroying all PCI devices for hot-removal.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Introduce functions to support dynamic IOMMU seq_id allocating and
releasing, which will be used to support DMAR hotplug.
Also rename IOMMU_UNITS_SUPPORTED as DMAR_UNITS_SUPPORTED.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Introduce helper function dmar_walk_resources to walk resource entries
in DMAR table and ACPI buffer object returned by ACPI _DSM method
for IOMMU hot-plug.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Simplify include/linux/dmar.h a bit based on the fact that
both CONFIG_INTEL_IOMMU and CONFIG_IRQ_REMAP select CONFIG_DMAR_TABLE.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
It's not only for PCI devices any more, and the scope information for an
ACPI device provides the bus and devfn so that has to be stored here too.
It is the device pointer itself which needs to be protected with RCU,
so the __rcu annotation follows it into the definition of struct
dmar_dev_scope, since we're no longer just passing arrays of device
pointers around.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now we have a PCI bus notification based mechanism to update DMAR
device scope array, we could extend the mechanism to support boot
time initialization too, which will help to unify and simplify
the implementation.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Current Intel DMAR/IOMMU driver assumes that all PCI devices associated
with DMAR/RMRR/ATSR device scope arrays are created at boot time and
won't change at runtime, so it caches pointers of associated PCI device
object. That assumption may be wrong now due to:
1) introduction of PCI host bridge hotplug
2) PCI device hotplug through sysfs interfaces.
Wang Yijing has tried to solve this issue by caching <bus, dev, func>
tupple instead of the PCI device object pointer, but that's still
unreliable because PCI bus number may change in case of hotplug.
Please refer to http://lkml.org/lkml/2013/11/5/64
Message from Yingjing's mail:
after remove and rescan a pci device
[ 611.857095] dmar: DRHD: handling fault status reg 2
[ 611.857109] dmar: DMAR:[DMA Read] Request device [86:00.3] fault addr ffff7000
[ 611.857109] DMAR:[fault reason 02] Present bit in context entry is clear
[ 611.857524] dmar: DRHD: handling fault status reg 102
[ 611.857534] dmar: DMAR:[DMA Read] Request device [86:00.3] fault addr ffff6000
[ 611.857534] DMAR:[fault reason 02] Present bit in context entry is clear
[ 611.857936] dmar: DRHD: handling fault status reg 202
[ 611.857947] dmar: DMAR:[DMA Read] Request device [86:00.3] fault addr ffff5000
[ 611.857947] DMAR:[fault reason 02] Present bit in context entry is clear
[ 611.858351] dmar: DRHD: handling fault status reg 302
[ 611.858362] dmar: DMAR:[DMA Read] Request device [86:00.3] fault addr ffff4000
[ 611.858362] DMAR:[fault reason 02] Present bit in context entry is clear
[ 611.860819] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[ 611.860983] dmar: DRHD: handling fault status reg 402
[ 611.860995] dmar: INTR-REMAP: Request device [[86:00.3] fault index a4
[ 611.860995] INTR-REMAP:[fault reason 34] Present field in the IRTE entry is clear
This patch introduces a new mechanism to update the DRHD/RMRR/ATSR device scope
caches by hooking PCI bus notification.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Global DMA and interrupt remapping resources may be accessed in
interrupt context, so use RCU instead of rwsem to protect them
in such cases.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Introduce a global rwsem dmar_global_lock, which will be used to
protect DMAR related global data structures from DMAR/PCI/memory
device hotplug operations in process context.
DMA and interrupt remapping related data structures are read most,
and only change when memory/PCI/DMAR hotplug event happens.
So a global rwsem solution is adopted for balance between simplicity
and performance.
For interrupt remapping driver, function intel_irq_remapping_supported(),
dmar_table_init(), intel_enable_irq_remapping(), disable_irq_remapping(),
reenable_irq_remapping() and enable_drhd_fault_handling() etc
are called during booting, suspending and resuming with interrupt
disabled, so no need to take the global lock.
For interrupt remapping entry allocation, the locking model is:
down_read(&dmar_global_lock);
/* Find corresponding iommu */
iommu = map_hpet_to_ir(id);
if (iommu)
/*
* Allocate remapping entry and mark entry busy,
* the IOMMU won't be hot-removed until the
* allocated entry has been released.
*/
index = alloc_irte(iommu, irq, 1);
up_read(&dmar_global_lock);
For DMA remmaping driver, we only uses the dmar_global_lock rwsem to
protect functions which are only called in process context. For any
function which may be called in interrupt context, we will use RCU
to protect them in following patches.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Introduce for_each_dev_scope()/for_each_active_dev_scope() to walk
{active} device scope entries. This will help following RCU lock
related patches.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Move private structures and variables into intel-iommu.c, which will
help to simplify locking policy for hotplug. Also delete redundant
declarations.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Factor out function dmar_alloc_dev_scope() from dmar_parse_dev_scope()
for later reuse.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Simplify vt-d related code with existing macros and introduce a new
macro for_each_active_drhd_unit() to enumerate all active DRHD unit.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Functions alloc_iommu() and parse_ioapics_under_ir()
are only used internally, so mark them as static.
[Joerg: Made detect_intel_iommu() non-static again for IA64]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Function dmar_parse_dev_scope() should release the PCI device reference
count gained in function dmar_parse_one_dev_scope() on error recovery,
otherwise it will cause PCI device object leakage.
This patch also introduces dmar_free_dev_scope(), which will be used
to support DMAR device hotplug.
Reviewed-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Remove the Intel specific interfaces from dmar.h and remove
asm/irq_remapping.h which is only used for io_apic.c anyway.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The operation for releasing a remapping entry is iommu
specific too.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Convert these calls too:
* Disable of remapping hardware
* Reenable of remapping hardware
* Enable fault handling
With that all of arch/x86/kernel/apic/apic.c is converted to
use the generic intr-remapping interface.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch introduces irq_remap_ops to hold implementation
specific function pointer to handle interrupt remapping. As
the first part the initialization functions for VT-d are
converted to these ops.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
x86_64 allnoconfig:
In file included from arch/x86/kernel/pci-dma.c:3:
include/linux/dmar.h:248: warning: 'struct acpi_dmar_header' declared inside parameter list
include/linux/dmar.h:248: warning: its scope is only this definition or declaration, which is probably not what you want
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the platforms which are x2apic and interrupt-remapping
capable, Linux kernel is enabling x2apic even if the BIOS
doesn't. This is to take advantage of the features that x2apic
brings in.
Some of the OEM platforms are running into issues because of
this, as their bios is not x2apic aware. For example, this was
resulting in interrupt migration issues on one of the platforms.
Also if the BIOS SMI handling uses APIC interface to send SMI's,
then the BIOS need to be aware of x2apic mode that OS has
enabled.
On some of these platforms, BIOS doesn't have a HW mechanism to
turnoff the x2apic feature to prevent OS from enabling it.
To resolve this mess, recent changes to the VT-d2 specification:
http://download.intel.com/technology/computing/vptech/Intel(r)_VT_for_Direct_IO.pdf
includes a mechanism that provides BIOS a way to request system
software to opt out of enabling x2apic mode.
Look at the x2apic optout flag in the DMAR tables before
enabling the x2apic mode in the platform. Also print a warning
that we have disabled x2apic based on the BIOS request.
Kernel boot parameter "intremap=no_x2apic_optout" can be used to
override the BIOS x2apic optout request.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: yinghai@kernel.org
Cc: joerg.roedel@amd.com
Cc: tony.luck@intel.com
Cc: dwmw2@infradead.org
Link: http://lkml.kernel.org/r/20110824001456.171766616@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The stubs for CONFIG_INTR_REMAP disabled need to be functions
instead of values to eliminate build warnings.
arch/x86/kernel/apic/apic.c: In function 'lapic_suspend':
arch/x86/kernel/apic/apic.c:2060:3: warning: statement with no effect
arch/x86/kernel/apic/apic.c: In function 'lapic_resume':
arch/x86/kernel/apic/apic.c:2137:3: warning: statement with no effect
Reported-and-Tested-by: Fabio Comolli <fabio.comolli@gmail.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <20101122124834.74429004.randy.dunlap@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
irq_2_iommu is in struct irq_cfg, so we can do the irq_remapped check
based on irq_cfg instead of going through a lookup function. That's
especially interesting in the eoi_ioapic_irq() hotpath.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
That interrupt remapping code is x86 specific and tied to the io_apic
code. No need for separate allocator functions in the interrupt
remapping code. This allows to simplify the code and irq_2_iommu is
small (13 bytes on 64bit) so it's not a real problem even if interrupt
remapping is runtime disabled. If it's compile time disabled the
impact is zero.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
We return 1 if the IOMMU has been detected. Zero or an error number
if we failed to find it. This is in preperation of using the IOMMU_INIT
so that we can detect whether an IOMMU is present. I have not
tested this for regression on Calgary, nor on AMD Vi chipsets as
I don't have that hardware.
CC: Muli Ben-Yehuda <muli@il.ibm.com>
CC: "Jon D. Mason" <jdmason@kudzu.us>
CC: "Darrick J. Wong" <djwong@us.ibm.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: David Woodhouse <David.Woodhouse@intel.com>
CC: Chris Wright <chrisw@sous-sol.org>
CC: Yinghai Lu <yinghai@kernel.org>
CC: Joerg Roedel <joerg.roedel@amd.com>
CC: H. Peter Anvin <hpa@zytor.com>
CC: Fujita Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
LKML-Reference: <1282845485-8991-3-git-send-email-konrad.wilk@oracle.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'timers-for-linus-hpet' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: hpet: Make WARN_ON understandable
x86: arch specific support for remapping HPET MSIs
intr-remap: generic support for remapping HPET MSIs
x86, hpet: Simplify the HPET code
x86, hpet: Disable per-cpu hpet timer if ARAT is supported
This changes detect_intel_iommu() to set intel_iommu_init() to
iommu_init hook if detect_intel_iommu() finds the IOMMU.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: chrisw@sous-sol.org
Cc: dwmw2@infradead.org
Cc: joerg.roedel@amd.com
Cc: muli@il.ibm.com
LKML-Reference: <1257849980-22640-6-git-send-email-fujita.tomonori@lab.ntt.co.jp>
[ -v2: build fix for the !CONFIG_DMAR case ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Lu Baolu
Christoph Hellwig
Kyung Min Park
Yian Chen
Qian Cai
Amol Grover
Deepa Dinamani
Thomas Gleixner
Suravee Suthikulpanit
Joerg Roedel
Ingo Molnar
Jiang Liu
David Woodhouse
Joerg Roedel
Andrew Morton
Suresh Siddha
Randy Dunlap
Linus Torvalds
Konrad Rzeszutek Wilk
FUJITA Tomonori