commit 65564157ae64cec0f527583f96e32f484f730f92 upstream.
We're seeing a GPU hang issue on a CHV platform, which was caused by commit
bac24f59f4 ("drm/i915/execlists: Enable coarse preemption boundaries for
Gen8").
The Gen8 platform only supports timeslicing and doesn't have a preemption
mechanism, as its engines do not have a preemption timer.
Commit 751f82b353 ("drm/i915/gt: Only disable preemption on Gen8 render
engines") addressed this issue only for render engines. This patch extends
that fix by ensuring that preemption is not considered for all engines on
Gen8 platforms.
v4:
- Use the correct Fixes tag (Rodrigo Vivi)
- Reworded commit log (Andi Shyti)
v3:
- Inside need_preempt(), condition of can_preempt() is not required
as simplified can_preempt() is enough. (Chris Wilson)
v2: Simplify can_preempt() function (Tvrtko Ursulin)
Fixes: 751f82b353 ("drm/i915/gt: Only disable preemption on gen8 render engines")
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/11396
Suggested-by: Andi Shyti <andi.shyti@intel.com>
Signed-off-by: Nitin Gote <nitin.r.gote@intel.com>
Cc: Chris Wilson <chris.p.wilson@linux.intel.com>
CC: <stable@vger.kernel.org> # v5.12+
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240711163208.1355736-1-nitin.r.gote@intel.com
(cherry picked from commit 7df0be6e6280c6fca01d039864bb123e5e36604b)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad97196379d0b8cb24ef3d5006978a6554e6467f upstream.
topa_entry->base is a bit-field. Bit-fields are not promoted to a 64-bit
type, even if the underlying type is 64-bit, and so, if necessary, must
be cast to a larger type when calculations are done.
Fix a topa_entry->base address calculation by adding a cast.
Without the cast, the address was limited to 36-bits i.e. 64GiB.
The address calculation is used on systems that do not support Multiple
Entry ToPA (only Broadwell), and affects physical addresses on or above
64GiB. Instead of writing to the correct address, the address comprising
the first 36 bits would be written to.
Intel PT snapshot and sampling modes are not affected.
Fixes: 52ca9ced3f ("perf/x86/intel/pt: Add Intel PT PMU driver")
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240624201101.60186-3-adrian.hunter@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5638bd722a44bbe97c1a7b3fae5b9efddb3e70ff upstream.
topa_entry->base needs to store a pfn. It obviously needs to be
large enough to store the largest possible x86 pfn which is
MAXPHYADDR-PAGE_SIZE (52-12). So it is 4 bits too small.
Increase the size of topa_entry->base from 36 bits to 40 bits.
Note, systems where physical addresses can be 256TiB or more are affected.
[ Adrian: Amend commit message as suggested by Dave Hansen ]
Fixes: 52ca9ced3f ("perf/x86/intel/pt: Add Intel PT PMU driver")
Signed-off-by: Marco Cavenati <cavenati.marco@gmail.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240624201101.60186-2-adrian.hunter@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5a6ff3d639d088d4af7e2935e1ee0d8b4e817d4 upstream.
The perf stat errors out with UNC_CHA_TOR_INSERTS.IA_HIT_CXL_ACC_LOCAL
event.
$perf stat -e uncore_cha_55/event=0x35,umask=0x10c0008101/ -a -- ls
event syntax error: '..0x35,umask=0x10c0008101/'
\___ Bad event or PMU
The definition of the CHA umask is config:8-15,32-55, which is 32bit.
However, the umask of the event is bigger than 32bit.
This is an error in the original uncore spec.
Add a new umask_ext5 for the new CHA umask range.
Fixes: 949b11381f ("perf/x86/intel/uncore: Add Sapphire Rapids server CHA support")
Closes: https://lore.kernel.org/linux-perf-users/alpine.LRH.2.20.2401300733310.11354@Diego/
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ian Rogers <irogers@google.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20240708185524.1185505-1-kan.liang@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a5465418f5fd970e86a86c7f4075be262682840 upstream.
The perf pending task work is never waited upon the matching event
release. In the case of a child event, released via free_event()
directly, this can potentially result in a leaked event, such as in the
following scenario that doesn't even require a weak IRQ work
implementation to trigger:
schedule()
prepare_task_switch()
=======> <NMI>
perf_event_overflow()
event->pending_sigtrap = ...
irq_work_queue(&event->pending_irq)
<======= </NMI>
perf_event_task_sched_out()
event_sched_out()
event->pending_sigtrap = 0;
atomic_long_inc_not_zero(&event->refcount)
task_work_add(&event->pending_task)
finish_lock_switch()
=======> <IRQ>
perf_pending_irq()
//do nothing, rely on pending task work
<======= </IRQ>
begin_new_exec()
perf_event_exit_task()
perf_event_exit_event()
// If is child event
free_event()
WARN(atomic_long_cmpxchg(&event->refcount, 1, 0) != 1)
// event is leaked
Similar scenarios can also happen with perf_event_remove_on_exec() or
simply against concurrent perf_event_release().
Fix this with synchonizing against the possibly remaining pending task
work while freeing the event, just like is done with remaining pending
IRQ work. This means that the pending task callback neither need nor
should hold a reference to the event, preventing it from ever beeing
freed.
Fixes: 517e6a301f ("perf: Fix perf_pending_task() UaF")
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240621091601.18227-5-frederic@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fd5ad3f310de22836cdacae919dd99d758a1f1b upstream.
When a task is scheduled out, pending sigtrap deliveries are deferred
to the target task upon resume to userspace via task_work.
However failures while adding an event's callback to the task_work
engine are ignored. And since the last call for events exit happen
after task work is eventually closed, there is a small window during
which pending sigtrap can be queued though ignored, leaking the event
refcount addition such as in the following scenario:
TASK A
-----
do_exit()
exit_task_work(tsk);
<IRQ>
perf_event_overflow()
event->pending_sigtrap = pending_id;
irq_work_queue(&event->pending_irq);
</IRQ>
=========> PREEMPTION: TASK A -> TASK B
event_sched_out()
event->pending_sigtrap = 0;
atomic_long_inc_not_zero(&event->refcount)
// FAILS: task work has exited
task_work_add(&event->pending_task)
[...]
<IRQ WORK>
perf_pending_irq()
// early return: event->oncpu = -1
</IRQ WORK>
[...]
=========> TASK B -> TASK A
perf_event_exit_task(tsk)
perf_event_exit_event()
free_event()
WARN(atomic_long_cmpxchg(&event->refcount, 1, 0) != 1)
// leak event due to unexpected refcount == 2
As a result the event is never released while the task exits.
Fix this with appropriate task_work_add()'s error handling.
Fixes: 517e6a301f ("perf: Fix perf_pending_task() UaF")
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240621091601.18227-4-frederic@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29e222085d8907ccff18ecd931bdd4c6b1f11b92 upstream.
Link up failure is observed as a result of flash read failure. Current
code does not check flash read return code where it relies on FW checksum
to detect the problem.
Add check of flash read failure to detect the problem sooner.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/202406210815.rPDRDMBi-lkp@intel.com/
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240710171057.35066-6-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c449b4198701d828e40d60a2abd30970b74a1d75 upstream.
On bsg timeout, hardware_lock is used as part of search for the srb.
Instead, qpair lock should be used to iterate through different qpair.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240710171057.35066-11-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3d98b12eef8db436e32f1a8c5478be57dc15621 upstream.
The device does not come online when the target port is online. There were
multiple RSCNs indicating multiple devices were affected. Driver is in the
process of finishing a fabric scan. A new RSCN (device up) arrived at the
tail end of the last fabric scan. Driver mistakenly thinks the new RSCN is
being taken care of by the previous fabric scan, where this notification is
cleared and not acted on. The laser needs to be blinked again to get the
device to show up.
To prevent driver from accidentally clearing the RSCN notification, each
RSCN is given a generation value. A fabric scan will scan for that
generation(s). Any new RSCN arrive after the scan start will have a new
generation value. This will trigger another scan to get latest data. The
RSCN notification flag will be cleared when the scan is associate to that
generation.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202406210538.w875N70K-lkp@intel.com/
Fixes: bb2ca6b3f0 ("scsi: qla2xxx: Relogin during fabric disturbance")
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240710171057.35066-2-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c184baccf0d5e2ef4cc1562261d0e48508a1c2b upstream.
Read/write callbacks registered with nvmem core expect 0 to be returned
on success and a negative value to be returned on failure.
cmos_nvram_read()/cmos_nvram_write() currently return the number of
bytes read or written, fix to return 0 on success and -EIO incase number
of bytes requested was not read or written.
Fixes: 8b5b7958fd ("rtc: cmos: use generic nvmem")
Cc: stable@vger.kernel.org
Signed-off-by: Joy Chakraborty <joychakr@google.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20240612083635.1253039-1-joychakr@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af649773fb25250cd22625af021fb6275c56a3ee upstream.
Since balancing mode was added in bda420b985 ("numa balancing: migrate
on fault among multiple bound nodes"), it was possible to set this mode
but it wouldn't be shown in /proc/<pid>/numa_maps since there was no
support for it in the mpol_to_str() helper.
Furthermore, because the balancing mode sets the MPOL_F_MORON flag, it
would be displayed as 'default' due a workaround introduced a few years
earlier in 8790c71a18 ("mm/mempolicy.c: fix mempolicy printing in
numa_maps").
To tidy this up we implement two changes:
Replace the MPOL_F_MORON check by pointer comparison against the
preferred_node_policy array. By doing this we generalise the current
special casing and replace the incorrect 'default' with the correct 'bind'
for the mode.
Secondly, we add a string representation and corresponding handling for
the MPOL_F_NUMA_BALANCING flag.
With the two changes together we start showing the balancing flag when it
is set and therefore complete the fix.
Representation format chosen is to separate multiple flags with vertical
bars, following what existed long time ago in kernel 2.6.25. But as
between then and now there wasn't a way to display multiple flags, this
patch does not change the format in practice.
Some /proc/<pid>/numa_maps output examples:
555559580000 bind=balancing:0-1,3 file=...
555585800000 bind=balancing|static:0,2 file=...
555635240000 prefer=relative:0 file=
Link: https://lkml.kernel.org/r/20240708075632.95857-1-tursulin@igalia.com
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Fixes: bda420b985 ("numa balancing: migrate on fault among multiple bound nodes")
References: 8790c71a18 ("mm/mempolicy.c: fix mempolicy printing in numa_maps")
Reviewed-by: "Huang, Ying" <ying.huang@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@vger.kernel.org> [5.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd50a974097bb82d52a458bd3ee39fb723129a0c upstream.
It will cause memory leakage when use driver API devm_free_percpu()
to free memory allocated by devm_alloc_percpu(), fixed by using
devres_release() instead of devres_destroy() within devm_free_percpu().
Fixes: ff86aae3b4 ("devres: add devm_alloc_percpu()")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/1719931914-19035-3-git-send-email-quic_zijuhu@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c884e3249f753dcef7a2b2023541ac1dc46b318e upstream.
Driver API devm_krealloc() calls alloc_dr() with wrong argument
@total_new_size, so causes more memory to be allocated than required
fix this memory waste by using @new_size as the argument for alloc_dr().
Fixes: f82485722e ("devres: provide devm_krealloc()")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/1719931914-19035-2-git-send-email-quic_zijuhu@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36e3b949e35964e22b9a57f960660fc599038dd4 upstream.
The NIC requires each TSO segment to not span more than 10
descriptors. NIC further requires each descriptor to not exceed
16KB - 1 (GVE_TX_MAX_BUF_SIZE_DQO).
The descriptors for an skb are generated by
gve_tx_add_skb_no_copy_dqo() for DQO RDA queue format.
gve_tx_add_skb_no_copy_dqo() loops through each skb frag and
generates a descriptor for the entire frag if the frag size is
not greater than GVE_TX_MAX_BUF_SIZE_DQO. If the frag size is
greater than GVE_TX_MAX_BUF_SIZE_DQO, it is split into descriptor(s)
of size GVE_TX_MAX_BUF_SIZE_DQO and a descriptor is generated for
the remainder (frag size % GVE_TX_MAX_BUF_SIZE_DQO).
gve_can_send_tso() checks if the descriptors thus generated for an
skb would meet the requirement that each TSO-segment not span more
than 10 descriptors. However, the current code misses an edge case
when a TSO segment spans multiple descriptors within a large frag.
This change fixes the edge case.
gve_can_send_tso() relies on the assumption that max gso size (9728)
is less than GVE_TX_MAX_BUF_SIZE_DQO and therefore within an skb
fragment a TSO segment can never span more than 2 descriptors.
Fixes: a57e5de476 ("gve: DQO: Add TX path")
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240724143431.3343722-1-pkaligineedi@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd6e9894b451e7c85cceb8e9dc5432679a70e7dc upstream.
zap_modalias_env() wrongly calculates size of memory block to move, so
will cause OOB memory access issue if variable MODALIAS is not the last
one within its @env parameter, fixed by correcting size to memmove.
Fixes: 9b3fa47d4a ("kobject: fix suppressing modalias in uevents delivered over netlink")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Lk Sii <lk_sii@163.com>
Link: https://lore.kernel.org/r/1717074877-11352-1-git-send-email-quic_zijuhu@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3415b10a03945b0da4a635e146750dfe5ce0f448 upstream.
After a recent change in clang to stop consuming all instances of '-S'
and '-c' [1], the stack protector scripts break due to the kernel's use
of -Werror=unused-command-line-argument to catch cases where flags are
not being properly consumed by the compiler driver:
$ echo | clang -o - -x c - -S -c -Werror=unused-command-line-argument
clang: error: argument unused during compilation: '-c' [-Werror,-Wunused-command-line-argument]
This results in CONFIG_STACKPROTECTOR getting disabled because
CONFIG_CC_HAS_SANE_STACKPROTECTOR is no longer set.
'-c' and '-S' both instruct the compiler to stop at different stages of
the pipeline ('-S' after compiling, '-c' after assembling), so having
them present together in the same command makes little sense. In this
case, the test wants to stop before assembling because it is looking at
the textual assembly output of the compiler for either '%fs' or '%gs',
so remove '-c' from the list of arguments to resolve the error.
All versions of GCC continue to work after this change, along with
versions of clang that do or do not contain the change mentioned above.
Cc: stable@vger.kernel.org
Fixes: 4f7fd4d7a7 ("[PATCH] Add the -fstack-protector option to the CFLAGS")
Fixes: 60a5317ff0 ("x86: implement x86_32 stack protector")
Link: 6461e53781 [1]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf6acd5d16057d7accbbb1bf7dc6d8c56eeb4ecc upstream.
The decompression code parses a huffman tree and counts the number of
symbols for a given bit length. In rare cases, there may be >= 256
symbols with a given bit length, causing the unsigned char to overflow.
This causes a decompression failure later when the code tries and fails to
find the bit length for a given symbol.
Since the maximum number of symbols is 258, use unsigned short instead.
Link: https://lkml.kernel.org/r/20240717162016.1514077-1-ross.lagerwall@citrix.com
Fixes: bc22c17e12 ("bzip2/lzma: library support for gzip, bzip2 and lzma decompression")
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Cc: Alain Knaff <alain@knaff.lu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 745d9f4a31defec731119ee8aad8ba9f2536dd9a upstream.
In case of a memory allocation failure in the volumes loop we can only
process the already allocated scan_eba and fm_eba array elements on the
error path - others are still uninitialized.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 00abf30415 ("UBI: Add self_check_eba()")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a83b22754e351f13fb46596c85f667dc33da71ec upstream.
The flag attribute of the struct clk_init_data isn't initialized before
the devm_clk_hw_register() call. This can lead to unexpected behavior
during registration.
Initialize the entire clk_init_data to zero at declaration.
Cc: stable@vger.kernel.org
Fixes: 58e1e2d2cd ("clk: davinci: cfgchip: Add TI DA8XX USB PHY clocks")
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Reviewed-by: David Lechner <david@lechnology.com>
Link: https://lore.kernel.org/r/20240718115534.41513-1-bastien.curutchet@bootlin.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce2065c4cc4f05635413f63f6dc038d7d4842e31 upstream.
Firmware only supports single DSDs in ELS Pass-through IOCB (0x53h), sg cnt
is decided by the SCSI ML. User is not aware of the cause of an acutal
error.
Return the appropriate return code that will be decoded by API and
application and proper error message will be displayed to user.
Fixes: 6e98016ca0 ("[SCSI] qla2xxx: Re-organized BSG interface specific code.")
Cc: stable@vger.kernel.org
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240710171057.35066-5-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fef55d8f78383c8e6d6d4c014b9597375132696 upstream.
If an NTFS file system is mounted to another system with different
PAGE_SIZE from the original system, log->page_size will change in
log_replay(), but log->page_{mask,bits} don't change correspondingly.
This will cause a panic because "u32 bytes = log->page_size - page_off"
will get a negative value in the later read_log_page().
Cc: stable@vger.kernel.org
Fixes: b46acd6a6a ("fs/ntfs3: Add NTFS journal")
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31643d84b8c3d9c846aa0e20bc033e46c68c7e7d upstream.
With the introduction of binder_available_for_proc_work_ilocked() in
commit 1b77e9dcc3 ("ANDROID: binder: remove proc waitqueue") a binder
thread can only "wait_for_proc_work" after its thread->looper has been
marked as BINDER_LOOPER_STATE_{ENTERED|REGISTERED}.
This means an unregistered reader risks waiting indefinitely for work
since it never gets added to the proc->waiting_threads. If there are no
further references to its waitqueue either the task will hang. The same
applies to readers using the (e)poll interface.
I couldn't find the rationale behind this restriction. So this patch
restores the previous behavior of allowing unregistered threads to
"wait_for_proc_work". Note that an error message for this scenario,
which had previously become unreachable, is now re-enabled.
Fixes: 1b77e9dcc3 ("ANDROID: binder: remove proc waitqueue")
Cc: stable@vger.kernel.org
Cc: Martijn Coenen <maco@google.com>
Cc: Arve Hjønnevåg <arve@google.com>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Link: https://lore.kernel.org/r/20240711201452.2017543-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 840b7a5edf88fe678c60dee88a135647c0ea4375 upstream.
Rockchip platforms use 'GPIO_ACTIVE_HIGH' flag in the devicetree definition
for ep_gpio. This means, whatever the logical value set by the driver for
the ep_gpio, physical line will output the same logic level.
For instance,
gpiod_set_value_cansleep(rockchip->ep_gpio, 0); --> Level low
gpiod_set_value_cansleep(rockchip->ep_gpio, 1); --> Level high
But while requesting the ep_gpio, GPIOD_OUT_HIGH flag is currently used.
Now, this also causes the physical line to output 'high' creating trouble
for endpoint devices during host reboot.
When host reboot happens, the ep_gpio will initially output 'low' due to
the GPIO getting reset to its POR value. Then during host controller probe,
it will output 'high' due to GPIOD_OUT_HIGH flag. Then during
rockchip_pcie_host_init_port(), it will first output 'low' and then 'high'
indicating the completion of controller initialization.
On the endpoint side, each output 'low' of ep_gpio is accounted for PERST#
assert and 'high' for PERST# deassert. With the above mentioned flow during
host reboot, endpoint will witness below state changes for PERST#:
(1) PERST# assert - GPIO POR state
(2) PERST# deassert - GPIOD_OUT_HIGH while requesting GPIO
(3) PERST# assert - rockchip_pcie_host_init_port()
(4) PERST# deassert - rockchip_pcie_host_init_port()
Now the time interval between (2) and (3) is very short as both happen
during the driver probe(), and this results in a race in the endpoint.
Because, before completing the PERST# deassertion in (2), endpoint got
another PERST# assert in (3).
A proper way to fix this issue is to change the GPIOD_OUT_HIGH flag in (2)
to GPIOD_OUT_LOW. Because the usual convention is to request the GPIO with
a state corresponding to its 'initial/default' value and let the driver
change the state of the GPIO when required.
As per that, the ep_gpio should be requested with GPIOD_OUT_LOW as it
corresponds to the POR value of '0' (PERST# assert in the endpoint). Then
the driver can change the state of the ep_gpio later in
rockchip_pcie_host_init_port() as per the initialization sequence.
This fixes the firmware crash issue in Qcom based modems connected to
Rockpro64 based board.
Fixes: e77f847df5 ("PCI: rockchip: Add Rockchip PCIe controller support")
Closes: https://lore.kernel.org/mhi/20240402045647.GG2933@thinkpad/
Link: https://lore.kernel.org/linux-pci/20240416-pci-rockchip-perst-fix-v1-1-4800b1d4d954@linaro.org
Reported-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Cc: stable@vger.kernel.org # v4.9
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28b8d7793b8573563b3d45321376f36168d77b1e upstream.
PERST# is active low according to the PCIe specification.
However, the existing pcie-dw-rockchip.c driver does:
gpiod_set_value(..., 0); msleep(100); gpiod_set_value(..., 1);
when asserting + deasserting PERST#.
This is of course wrong, but because all the device trees for this
compatible string have also incorrectly marked this GPIO as ACTIVE_HIGH:
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3568*
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3588*
The actual toggling of PERST# is correct, and we cannot change it anyway,
since that would break device tree compatibility.
However, this driver does request the GPIO to be initialized as
GPIOD_OUT_HIGH, which does cause a silly sequence where PERST# gets
toggled back and forth for no good reason.
Fix this by requesting the GPIO to be initialized as GPIOD_OUT_LOW (which
for this driver means PERST# asserted).
This will avoid an unnecessary signal change where PERST# gets deasserted
(by devm_gpiod_get_optional()) and then gets asserted (by
rockchip_pcie_start_link()) just a few instructions later.
Before patch, debug prints on EP side, when booting RC:
[ 845.606810] pci: PERST# asserted by host!
[ 852.483985] pci: PERST# de-asserted by host!
[ 852.503041] pci: PERST# asserted by host!
[ 852.610318] pci: PERST# de-asserted by host!
After patch, debug prints on EP side, when booting RC:
[ 125.107921] pci: PERST# asserted by host!
[ 132.111429] pci: PERST# de-asserted by host!
This extra, very short, PERST# assertion + deassertion has been reported to
cause issues with certain WLAN controllers, e.g. RTL8822CE.
Fixes: 0e898eb8df ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Link: https://lore.kernel.org/linux-pci/20240417164227.398901-1-cassel@kernel.org
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fea93a3e5d5e6a09eb153866d2ce60ea3287a70d upstream.
The intent of the code snippet is to always return 0 for both
PCI_INTERRUPT_LINE and PCI_INTERRUPT_PIN.
The check misses PCI_INTERRUPT_PIN. This patch fixes that.
This is discovered by this call in VFIO:
pci_read_config_byte(vdev->pdev, PCI_INTERRUPT_PIN, &pin);
The old code does not set *val to 0 because it misses the check for
PCI_INTERRUPT_PIN. Garbage is returned in that case.
Fixes: 4daace0d8c ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Link: https://lore.kernel.org/linux-pci/20240701202606.129606-1-wei.liu@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14cba6ace79627a57fb9058582b03f0ed3832390 upstream.
amd_rng_mod_init() uses pci_read_config_dword() that returns PCIBIOS_*
codes. The return code is then returned as is but amd_rng_mod_init() is
a module_init() function that should return normal errnos.
Convert PCIBIOS_* returns code using pcibios_err_to_errno() into normal
errno before returning it.
Fixes: 96d63c0297 ("[PATCH] Add AMD HW RNG driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c830eef806679dc243e191f962c488dd9d00708 upstream.
Andrea reported that the following innocuous litmus test:
C T
{}
P0(spinlock_t *x)
{
int r0;
spin_lock(x);
spin_unlock(x);
r0 = spin_is_locked(x);
}
gives rise to a nonsensical empty result with no executions:
$ herd7 -conf linux-kernel.cfg T.litmus
Test T Required
States 0
Ok
Witnesses
Positive: 0 Negative: 0
Condition forall (true)
Observation T Never 0 0
Time T 0.00
Hash=6fa204e139ddddf2cb6fa963bad117c0
The problem is caused by a bug in the lock.cat part of the LKMM. Its
computation of the rf relation for RU (read-unlocked) events is
faulty; it implicitly assumes that every RU event must read from
either a UL (unlock) event in another thread or from the lock's
initial state. Neither is true in the litmus test above, so the
computation yields no possible executions.
The lock.cat code tries to make up for this deficiency by allowing RU
events outside of critical sections to read from the last po-previous
UL event. But it does this incorrectly, trying to keep these rfi links
separate from the rfe links that might also be needed, and passing only
the latter to herd7's cross() macro.
The problem is fixed by merging the two sets of possible rf links for
RU events and using them all in the call to cross().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrea Parri <parri.andrea@gmail.com>
Closes: https://lore.kernel.org/linux-arch/ZlC0IkzpQdeGj+a3@andrea/
Tested-by: Andrea Parri <parri.andrea@gmail.com>
Acked-by: Andrea Parri <parri.andrea@gmail.com>
Fixes: 15553dcbca ("tools/memory-model: Add model support for spin_is_locked()")
CC: <stable@vger.kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21451dfd853e7d8e6e3fbd7ef1fbdb2f2ead12f5 upstream.
Sonix HD USB Camera does not support reading the sample rate which leads
to many lines of "cannot get freq at ep 0x84".
This patch adds the USB ID to quirks.c and avoids those error messages.
(snip)
[1.789698] usb 3-3: new high-speed USB device number 2 using xhci_hcd
[1.984121] usb 3-3: New USB device found, idVendor=0c45, idProduct=6340, bcdDevice= 0.00
[1.984124] usb 3-3: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[1.984127] usb 3-3: Product: USB 2.0 Camera
[1.984128] usb 3-3: Manufacturer: Sonix Technology Co., Ltd.
[5.440957] usb 3-3: 3:1: cannot get freq at ep 0x84
[12.130679] usb 3-3: 3:1: cannot get freq at ep 0x84
[12.175065] usb 3-3: 3:1: cannot get freq at ep 0x84
Signed-off-by: wangdicheng <wangdicheng@kylinos.cn>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20240722084822.31620-1-wangdich9700@163.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7010d9464f7ca3ee2d75095ea2e642a9009a41ff upstream.
The quirk_flags_table[] is sorted in the USB ID order, while the last
fix was put at a wrong position. Adjust the entry at the right
position.
Fixes: 74dba2408818 ("ALSA: usb-audio: Fix microphone sound on HD webcam.")
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20240722080605.23481-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 322a569c4b4188a0da2812f9e952780ce09b74ba upstream.
Move the non-VMX chunk of the "interrupt blocked" checks to a separate
helper so that KVM can reuse the code to detect if interrupts are blocked
for L2, e.g. to determine if a virtual interrupt _for L2_ is a valid wake
event. If L1 disables HLT-exiting for L2, nested APICv is enabled, and L2
HLTs, then L2 virtual interrupts are valid wake events, but if and only if
interrupts are unblocked for L2.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240607172609.3205077-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4aa99c71e42ad60178c1154ec24e3df9c684fb67 upstream.
There's no reason to have jbd2_journal_get_max_txn_bufs() public
function. Currently all users are internal and can use
journal->j_max_transaction_buffers instead. This saves some unnecessary
recomputations of the limit as a bonus which becomes important as this
function gets more complex in the following patch.
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://patch.msgid.link/20240624170127.3253-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce068e83976140badb19c7f1307926b4b562fac4 upstream.
ich7_lpc_probe() uses pci_read_config_dword() that returns PCIBIOS_*
codes. The error handling code assumes incorrectly it's a normal errno
and checks for < 0. The return code is returned from the probe function
as is but probe functions should return normal errnos.
Remove < 0 from the check and convert PCIBIOS_* returns code using
pcibios_err_to_errno() into normal errno before returning it.
Fixes: a328e95b82 ("leds: LED driver for Intel NAS SS4200 series (v5)")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240527132700.14260-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a17b9f590f6ec2b9f1b12b1db3bf1d181de6b272 upstream.
When changing the interface type we also need to update the bss_num, the
driver private data is searched based on a unique (bss_type, bss_num)
tuple, therefore every time bss_type changes, bss_num must also change.
This fixes for example an issue in which, after the mode changed, a
wireless scan on the changed interface would not finish, leading to
repeated -EBUSY messages to userspace when other scan requests were
sent.
Fixes: c606008b70 ("mwifiex: Properly initialize private structure on interface type changes")
Cc: stable@vger.kernel.org
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240510110458.15475-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8b632e89a101dae349a7b212c1771d7925f441b upstream.
io_uring_cancel_generic() should retry if any state changes like a
request is completed, however in case of a task exit it only goes for
another loop and avoids schedule() if any tracked (i.e. REQ_F_INFLIGHT)
request got completed.
Let's assume we have a non-tracked request executing in iowq and a
tracked request linked to it. Let's also assume
io_uring_cancel_generic() fails to find and cancel the request, i.e.
via io_run_local_work(), which may happen as io-wq has gaps.
Next, the request logically completes, io-wq still hold a ref but queues
it for completion via tw, which happens in
io_uring_try_cancel_requests(). After, right before prepare_to_wait()
io-wq puts the request, grabs the linked one and tries executes it, e.g.
arms polling. Finally the cancellation loop calls prepare_to_wait(),
there are no tw to run, no tracked request was completed, so the
tctx_inflight() check passes and the task is put to indefinite sleep.
Cc: stable@vger.kernel.org
Fixes: 3f48cf18f8 ("io_uring: unify files and task cancel")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/acac7311f4e02ce3c43293f8f1fda9c705d158f1.1721819383.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9ca51596bbfd0f9c386dd1c613c394c78d9e5e6 upstream.
The syzbot constructs a directory that has no dirblock but is non-inline,
i.e. the first directory block is a hole. And no errors are reported when
creating files in this directory in the following flow.
ext4_mknod
...
ext4_add_entry
// Read block 0
ext4_read_dirblock(dir, block, DIRENT)
bh = ext4_bread(NULL, inode, block, 0)
if (!bh && (type == INDEX || type == DIRENT_HTREE))
// The first directory block is a hole
// But type == DIRENT, so no error is reported.
After that, we get a directory block without '.' and '..' but with a valid
dentry. This may cause some code that relies on dot or dotdot (such as
make_indexed_dir()) to crash.
Therefore when ext4_read_dirblock() finds that the first directory block
is a hole report that the filesystem is corrupted and return an error to
avoid loading corrupted data from disk causing something bad.
Reported-by: syzbot+ae688d469e36fb5138d0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ae688d469e36fb5138d0
Fixes: 4e19d6b65f ("ext4: allow directory holes")
Cc: stable@kernel.org
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20240702132349.2600605-3-libaokun@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50ea741def587a64e08879ce6c6a30131f7111e7 upstream.
Syzbot reports a issue as follows:
============================================
BUG: unable to handle page fault for address: ffffed11022e24fe
PGD 23ffee067 P4D 23ffee067 PUD 0
Oops: Oops: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 0 PID: 5079 Comm: syz-executor306 Not tainted 6.10.0-rc5-g55027e689933 #0
Call Trace:
<TASK>
make_indexed_dir+0xdaf/0x13c0 fs/ext4/namei.c:2341
ext4_add_entry+0x222a/0x25d0 fs/ext4/namei.c:2451
ext4_rename fs/ext4/namei.c:3936 [inline]
ext4_rename2+0x26e5/0x4370 fs/ext4/namei.c:4214
[...]
============================================
The immediate cause of this problem is that there is only one valid dentry
for the block to be split during do_split, so split==0 results in out of
bounds accesses to the map triggering the issue.
do_split
unsigned split
dx_make_map
count = 1
split = count/2 = 0;
continued = hash2 == map[split - 1].hash;
---> map[4294967295]
The maximum length of a filename is 255 and the minimum block size is 1024,
so it is always guaranteed that the number of entries is greater than or
equal to 2 when do_split() is called.
But syzbot's crafted image has no dot and dotdot in dir, and the dentry
distribution in dirblock is as follows:
bus dentry1 hole dentry2 free
|xx--|xx-------------|...............|xx-------------|...............|
0 12 (8+248)=256 268 256 524 (8+256)=264 788 236 1024
So when renaming dentry1 increases its name_len length by 1, neither hole
nor free is sufficient to hold the new dentry, and make_indexed_dir() is
called.
In make_indexed_dir() it is assumed that the first two entries of the
dirblock must be dot and dotdot, so bus and dentry1 are left in dx_root
because they are treated as dot and dotdot, and only dentry2 is moved
to the new leaf block. That's why count is equal to 1.
Therefore add the ext4_check_dx_root() helper function to add more sanity
checks to dot and dotdot before starting the conversion to avoid the above
issue.
Reported-by: syzbot+ae688d469e36fb5138d0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ae688d469e36fb5138d0
Fixes: ac27a0ec11 ("[PATCH] ext4: initial copy of files from ext3")
Cc: stable@kernel.org
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20240702132349.2600605-2-libaokun@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d8491d3e726984343dd8c3cdbe2f2b47cfdd928 upstream.
On an Amiga 1200 equipped with a Warp1260 accelerator, an interrupt
storm coming from the accelerator board causes the machine to crash in
local_irq_enable() or auto_irq_enable(). Disabling interrupts for the
Warp1260 in amiga_parse_bootinfo() fixes the problem.
Link: https://lore.kernel.org/r/ZkjwzVwYeQtyAPrL@amaterasu.local
Cc: stable <stable@kernel.org>
Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20240601153254.186225-1-p.pisati@gmail.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a90d4471146de21745980cba51ce88e7926bcc4f upstream.
When the filesystem block bitmap is corrupted, we detect the corruption
while loading the bitmap and fail the allocation with error. However the
next allocation from the same bitmap will notice the bitmap buffer is
already loaded and tries to allocate from the bitmap with mixed results
(depending on the exact nature of the bitmap corruption). Fix the
problem by using BH_verified bit to indicate whether the bitmap is valid
or not.
Reported-by: syzbot+5f682cd029581f9edfd1@syzkaller.appspotmail.com
CC: stable@vger.kernel.org
Link: https://patch.msgid.link/20240617154201.29512-2-jack@suse.cz
Fixes: 1e0d4adf17 ("udf: Check consistency of Space Bitmap Descriptor")
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f409530e4db9dd11b88cb7703c97c8f326ff6566 upstream.
Re-introduce task_work_cancel(), this time to cancel an actual callback
and not *any* callback pointing to a given function. This is going to be
needed for perf events event freeing.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240621091601.18227-3-frederic@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68cbd415dd4b9c5b9df69f0f091879e56bf5907a upstream.
A proper task_work_cancel() API that actually cancels a callback and not
*any* callback pointing to a given function is going to be needed for
perf events event freeing. Do the appropriate rename to prepare for
that.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240621091601.18227-2-frederic@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bc73505a5cd2a18a7a542022722f136c19e3b87 upstream.
Inside unpack_profile() data->data is allocated using kvmemdup() so it
should be freed with the corresponding kvfree_sensitive().
Also add missing data->data release for rhashtable insertion failure path
in unpack_profile().
Found by Linux Verification Center (linuxtesting.org).
Fixes: e025be0f26 ("apparmor: support querying extended trusted helper extra data")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3af7524b14198f5159a86692d57a9f28ec9375ce upstream.
Running N CPU-bound tasks on an N CPUs platform:
- with asymmetric CPU capacity
- not being a DynamIq system (i.e. having a PKG level sched domain
without the SD_SHARE_PKG_RESOURCES flag set)
.. might result in a task placement where two tasks run on a big CPU
and none on a little CPU. This placement could be more optimal by
using all CPUs.
Testing platform:
Juno-r2:
- 2 big CPUs (1-2), maximum capacity of 1024
- 4 little CPUs (0,3-5), maximum capacity of 383
Testing workload ([1]):
Spawn 6 CPU-bound tasks. During the first 100ms (step 1), each tasks
is affine to a CPU, except for:
- one little CPU which is left idle.
- one big CPU which has 2 tasks affine.
After the 100ms (step 2), remove the cpumask affinity.
Behavior before the patch:
During step 2, the load balancer running from the idle CPU tags sched
domains as:
- little CPUs: 'group_has_spare'. Cf. group_has_capacity() and
group_is_overloaded(), 3 CPU-bound tasks run on a 4 CPUs
sched-domain, and the idle CPU provides enough spare capacity
regarding the imbalance_pct
- big CPUs: 'group_overloaded'. Indeed, 3 tasks run on a 2 CPUs
sched-domain, so the following path is used:
group_is_overloaded()
\-if (sgs->sum_nr_running <= sgs->group_weight) return true;
The following path which would change the migration type to
'migrate_task' is not taken:
calculate_imbalance()
\-if (env->idle != CPU_NOT_IDLE && env->imbalance == 0)
as the local group has some spare capacity, so the imbalance
is not 0.
The migration type requested is 'migrate_util' and the busiest
runqueue is the big CPU's runqueue having 2 tasks (each having a
utilization of 512). The idle little CPU cannot pull one of these
task as its capacity is too small for the task. The following path
is used:
detach_tasks()
\-case migrate_util:
\-if (util > env->imbalance) goto next;
After the patch:
As the number of failed balancing attempts grows (with
'nr_balance_failed'), progressively make it easier to migrate
a big task to the idling little CPU. A similar mechanism is
used for the 'migrate_load' migration type.
Improvement:
Running the testing workload [1] with the step 2 representing
a ~10s load for a big CPU:
Before patch: ~19.3s
After patch: ~18s (-6.7%)
Similar issue reported at:
https://lore.kernel.org/lkml/20230716014125.139577-1-qyousef@layalina.io/
Suggested-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Qais Yousef <qyousef@layalina.io>
Link: https://lore.kernel.org/r/20231206090043.634697-1-pierre.gondois@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nitin Gote
Adrian Hunter
Marco Cavenati
Kan Liang
Frederic Weisbecker
Nilesh Javali
Shreyas Deodhar
Quinn Tran
Manish Rangankar
Joy Chakraborty
Tvrtko Ursulin
Zijun Hu
Bailey Forrest
Nathan Chancellor
Ross Lagerwall
Fedor Pchelkin
Bastien Curutchet
Saurav Kashyap
Huacai Chen
tuhaowen
Carlos Llamas
Manivannan Sadhasivam
Niklas Cassel
Wei Liu
Ilpo Järvinen
Alan Stern
wangdicheng
Takashi Iwai
Sean Christopherson
Ricardo Ribalda
Jan Kara
Rafael Beims
Mickaël Salaün
Pavel Begunkov
Baokun Li
Paolo Pisati
Pierre Gondois