cast to u64.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove acpi_hw_write_gpe_enable_reg, it had been reduced down to a
single line of code, and called from only one place.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add data table compiler output component
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Header file support.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The acpi_set_gpe() function is a little awkward, because it doesn't
really work as advertised in the "disable" case. Namely, if a GPE
has been enabled with acpi_enable_gpe() and triggered a notification
to occur, and if acpi_set_gpe() is used to disable it before
acpi_ev_asynch_enable_gpe() runs, the GPE will be immediately enabled
by the latter as though the acpi_set_gpe() had no effect.
Thus, since it's been possible to make all of its callers use
alternative operations to disable or enable GPEs, acpi_set_gpe() can
be dropped.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The GPE block initialization code in acpi_ev_initialize_gpe_block()
uses acpi_set_gpe() to make sure that the GPEs with nonzero
runtime counter will remain enabled, but since it already has
a struct acpi_gpe_event_info object for each GPE, it might use
the low-level GPE enabling function, acpi_clear_and_enable_gpe(),
for this purpose.
To make that happen, move acpi_clear_and_enable_gpe() to
drivers/acpi/acpica/evgpe.c and rename it to acpi_ev_enable_gpe(),
modify the two existing users of it accordingly and modify
acpi_ev_initialize_gpe_block() to use it instead of acpi_set_gpe()
and to check its return value.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The EC driver is the last user of acpi_set_gpe() and since it is
guaranteed that the EC GPE will not be shared, acpi_disable_gpe()
and acpi_enable_gpe() may be used for disabling the GPE temporarilty
if a GPE storm is detected and re-enabling it during EC transactions.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The suspend and resume routines provided by the EC driver are not
really necessary, because the handler of the GPE disabled by them
is not going to be executed after suspend_device_irqs() and before
resume_device_irqs() anyway.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
After the previous patch that introduced acpi_gpe_wakeup() and
modified the ACPI suspend and wakeup code to use it, the third
argument of acpi_{enable|disable}_gpe() and the GPE wakeup
reference counter are not necessary any more. Remove them and
modify all of the users of acpi_{enable|disable}_gpe()
accordingly. Also drop GPE type constants that aren't used
any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses reference counters to avoid disabling GPEs too early in
case they have been enabled for many times. This is done separately
for runtime and for wakeup, but the wakeup GPE reference counter is
not really necessary, because GPEs are only enabled to wake up the
system at the hardware level by acpi_enter_sleep_state(). Thus it
only is necessary to set the corresponding bits in the wakeup enable
masks of these GPEs' registers right before the system enters a sleep
state. Moreover, the GPE wakeup enable bits can only be set when the
target sleep state of the system is known and they need to be cleared
immediately after wakeup regardless of how many wakeup devices are
associated with a given GPE.
On the basis of the above observations, introduce function
acpi_gpe_wakeup() to be used for setting or clearing the enable bit
corresponding to a given GPE in its enable register's enable_for_wake
mask. Modify the ACPI suspend and wakeup code the use
acpi_gpe_wakeup() instead of acpi_{enable|disable}_gpe() to set
and clear GPE enable bits in their registers' enable_for_wake masks
during system transitions to a sleep state and back to the working
state, respectively. [This will allow us to drop the third
argument of acpi_{enable|disable}_gpe() and simplify the GPE
handling code.]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rename acpi_hw_gpe_register_bit to acpi_hw_get_gpe_register_bit
in order to be same with ACPICA code base.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Version 20100528.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
These ACPI tables have been seen in the field, but the actual
table definitions are unkown at this time.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On control method exit, only walk the namespace if the method is
known to have created namespace objects outside of its local scope.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove obsolete AOPOBJ_SINGLE_DATUM. Add AOPOBJ_INVALID for
use if the host OS rejects the address of an operation region
(currently only used by Linux.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change enhances the performance of namespace searches and
walks by adding a backpointer to the parent in each namespace
node. On large namespaces, this change can improve overall ACPI
performance by up to 9X. Adding a pointer to each namespace node
increases the overall size of the internal namespace by about 5%,
since each namespace entry usually consists of both a namespace
node and an ACPI operand object.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Expand the various device initialization counters from 16-bit
to 32-bit. Allows for very large namespaces.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
With only a few exceptions, ACPICA does not use signed integers.
Therefore, %d is incorrect.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Expand the various initialization counters from 16-bit to 32-bit.
Allows for very large namespaces.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
These objects are defined by "Windows Instrumentation", and are
not part of the ACPI spec. Adds compiler support and runtime
typechecking support in the ACPICA core. ACPICA BZ 860.
http://www.acpica.org/bugzilla/show_bug.cgi?id=860
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Because of package index values used for _BQC and _BCM.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6205/1: perf: ensure counter delta is treated as unsigned
ARM: 6202/1: Do not ARM_DMA_MEM_BUFFERABLE on RealView boards with L210/L220
ARM: 6201/1: RealView: Do not use outer_sync() on ARM11MPCore boards with L220
ARM: 6195/1: OMAP3: pmu: make CPU_HAS_PMU dependent on OMAP3_EMU
ARM: 6194/1: change definition of cpu_relax() for ARM11MPCore
ARM: 6193/1: RealView: Align the machine_desc.phys_io to 1MB section
ARM: 6192/1: VExpress: Align the machine_desc.phys_io to 1MB section
ARM: 6188/1: Add a config option for the ARM11MPCore DMA cache maintenance workaround
ARM: 6187/1: The v6_dma_inv_range() function must preserve data on SMP
ARM: 6186/1: Avoid the CONSISTENT_DMA_SIZE warning on noMMU builds
ARM: mx3: mx31lilly: fix build error for !CONFIG_USB_ULPI
[ARM] mmp: fix build failure due to IRQ_PMU depends on ARCH_PXA
[ARM] pxa/mioa701: fix camera regression
[ARM] pxa/z2: fix flash layout to final version
[ARM] pxa/z2: fix missing include in battery driver
[ARM] pxa: fix incorrect gpio type in udc_pxa2xx.h
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Fix incorrect branches event on AMD CPUs
perf tools: Fix find tids routine by excluding "." and ".."
x86: Send a SIGTRAP for user icebp traps
We should initialize the module dynamic debug datastructures
only after determining that the module is not loaded yet. This
fixes a bug that introduced in 2.6.35-rc2, where when a trying
to load a module twice, we also load it's dynamic printing data
twice which causes all sorts of nasty issues. Also handle
the dynamic debug cleanup later on failure.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (removed a #ifdef)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: remove block number from inode lookup code
xfs: rename XFS_IGET_BULKSTAT to XFS_IGET_UNTRUSTED
xfs: validate untrusted inode numbers during lookup
xfs: always use iget in bulkstat
xfs: prevent swapext from operating on write-only files
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/i7core:
MAINTAINERS: Add an entry for i7core_edac
i7core_edac: Avoid doing multiple probes for the same card
i7core_edac: Properly discover the first QPI device
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
kbuild: Propagate LOCALVERSION= down to scripts/setlocalversion
kbuild: Clean up and speed up the localversion logic
Hardware performance counters on ARM are 32-bits wide but atomic64_t
variables are used to represent counter data in the hw_perf_event structure.
The armpmu_event_update function right-shifts a signed 64-bit delta variable
and adds the result to the event count. This can lead to shifting in sign-bits
if the MSB of the 32-bit counter value is set. This results in perf output
such as:
Performance counter stats for 'sleep 20':
18446744073460670464 cycles <-- 0xFFFFFFFFF12A6000
7783773 instructions # 0.000 IPC
465 context-switches
161 page-faults
1172393 branches
20.154242147 seconds time elapsed
This patch ensures that the delta value is treated as unsigned so that the
right shift sets the upper bits to zero.
Cc: <stable@kernel.org>
Acked-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While doing some performance counter validation tests on some
assembly language programs I noticed that the "branches:u"
count was very wrong on AMD machines.
It looks like the wrong event was selected.
Signed-off-by: Vince Weaver <vweaver1@eecs.utk.edu>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: <stable@kernel.org>
LKML-Reference: <alpine.DEB.2.00.1007011526010.23160@cl320.eecs.utk.edu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Convert ppc4xx adma driver to use new node pointer location
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
While here, fixes the mailing list for i5400_edac
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As Nehalem/Nehalem-EP/Westmere devices uses several devices for the same
functionality (memory controller), the default way of proping devices doesn't
work. So, instead of a per-device probe, all devices should be probed at once.
This means that we should block any new attempt of probe, otherwise, it will
try to register the same device several times.
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Nehalem/Nehalem-EP/Westmere, the first QPI device is the last PCI bus.
The last bus is generally at 0x3f or 0xff, but there are also other systems
using different setups. For example, HP Z800 has 0x7f as the last bus.
This patch adds a logic to discover the last bus, dynamically detecting it
at runtime.
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When calculating the DCT channel from the syndrome we need to know the
syndrome type (x4 vs x8). On F10h, this is read out from extended PCI
cfg space register F3x180 while on K8 we only support x4 syndromes and
don't have extended PCI config space anyway.
Make the code accessing F3x180 F10h only and fall back to x4 syndromes
on everything else.
Cc: <stable@kernel.org> # .33.x .34.x
Reported-by: Jeffrey Merkey <jeffmerkey@gmail.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
RealView boards with certain revisions of the L210/L220 cache controller
may have issues (hardware deadlock) with the mandatory barriers (DSB
followed by an L2 cache sync) when ARM_DMA_MEM_BUFFERABLE is enabled.
The patch disables ARM_DMA_MEM_BUFFERABLE for these boards.
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
RealView boards with certain revisions of the L220 cache controller (ARM11*
processors only) may have issues (hardware deadlock) with the recent changes to
the mb() barrier implementation (DSB followed by an L2 cache sync). The patch
redefines the RealView ARM11MPCore mandatory barriers without the outer_sync()
call.
Cc: <stable@kernel.org>
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix page flip finish vs. prepare on plane B
drm/i915: change default panel fitting mode to preserve aspect ratio
drm/i915: fix uninitialized variable warning in i915_setup_compression()
drm/i915: take struct_mutex in i915_dma_cleanup()
drm/i915: Fix CRT hotplug regression in 2.6.35-rc1
i915: fix ironlake edp panel setup (v4)
drm/i915: don't access FW_BLC_SELF on 965G
drm/i915: Account for space on the ring buffer consumed whilst wrapping.
drm/i915: gen3 page flipping fixes
drm/i915: don't queue flips during a flip pending event
drm/i915: Fix incorrect intel_ring_begin size in BSD ringbuffer.
drm/i915: Turn on 945 self-refresh only if single CRTC is active
drm/i915/gen4: Fix interrupt setup ordering
drm/i915: Use RSEN instead of HTPLG for tfp410 monitor detection.
drm/i915: Move non-phys cursors into the GTT
Revert "drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on)."
(Included the "fix page flip finish vs. prepare on plane B" patch from
Jesse on top of the pull request from Eric. -- Linus)
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata_generic: implement ATA_GEN_* flags and force enable DMA on MBP 7,1
ahci,ata_generic: let ata_generic handle new MBP w/ MCP89
libahci: Fix bug in storing EM messages
When booting 2.6.35-rc3 on a x86 system without an ERST ACPI table with
the 'quiet' option, we still observe an "ERST: Table is not found!"
warning.
Quiesce it to the same info log level as the other 'table not found'
warnings.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 4bdadb9785 ("drm/i915:
Selectively enable self-reclaim"), we've been passing GFP_MOVABLE to the
i915 page allocator where we weren't before due to some over-eager
removal of the page mapping gfp_flags games the code used to play.
This caused hibernate on Intel hardware to result in a lot of memory
corruptions on resume. See for example
http://bugzilla.kernel.org/show_bug.cgi?id=13811
Reported-by: Evengi Golov (in bugzilla)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tested-by: M. Vefa Bicakci <bicave@superonline.com>
Cc: stable@kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We did this a long time ago in the DDX driver, but now this fix belongs
in the kernel.
Preserving the aspect ratio is a nicer default.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=18033.
Tested-by: Josh Triplett <josh@freedesktop.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes:
drivers/gpu/drm/i915/i915_dma.c: In function ‘i915_setup_compression’:
drivers/gpu/drm/i915/i915_dma.c:1311: error: ‘compressed_llb’ may be used uninitialized in this function
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
intel_cleanup_ring_buffer() calls drm_gem_object_unreference() (as
opposed to drm_gem_object_unreference_unlocked()) so it needs to be
called with "struct_mutex" held. If we don't hold the lock, it triggers
a BUG_ON(!mutex_is_locked(&dev->struct_mutex));
I also audited the other places that call intel_cleanup_ring_buffer()
and they all hold the lock so they're OK.
This was introduced in: 8187a2b70e "drm/i915: introduce
intel_ring_buffer structure (V2)" and it's a regression from v2.6.34.
Addresses: https://bugzilla.kernel.org/show_bug.cgi?id=16247
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reported-by: Benny Halevy <bhalevy@panasas.com>
Tested-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 7a772c492f has two bugs which
made the hotplug problems on my laptop worse instead of better.
First, it did not, in fact, disable the CRT plug interrupt -- it
disabled all the other hotplug interrupts. It seems rather doubtful
that that bit of the patch fixed anything, so let's just remove it.
(If you want to add it back, you probably meant ~CRT_HOTPLUG_INT_EN.)
Second, on at least my GM45, setting CRT_HOTPLUG_ACTIVATION_PERIOD_64
and CRT_HOTPLUG_VOLTAGE_COMPARE_50 (when they were previously unset)
causes a hotplug interrupt about three seconds later. The old code
never restored PORT_HOTPLUG_EN so this could only happen once, but
they new code restores those registers. So just set those bits when
we set up the interrupt in the first place.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Eric Anholt <eric@anholt.net>
Bob Moore
Rafael J. Wysocki
Lin Ming
Alexey Starikovskiy
Linus Torvalds
Yehuda Sadeh
Will Deacon
Vince Weaver
Dan Williams
Mauro Carvalho Chehab
Borislav Petkov
Michal Marek
Catalin Marinas
Jesse Barnes
Daniel J Blueman
Jesse Barnes
Prarit Bhargava
Dan Carpenter
Andy Lutomirski